Other DMX products
Other DMX products
Control Gear
Installation Guide
PRODUCT CARE AND HANDLING
•KKDC products are delivered in appropriate packaging. Any handling instructions on the packaging must be observed. Products
should remain in packaging ‘as delivered’ until installation or for ongoing transportation and storage.
•Inspect products carefully before installation. Do not proceed to install any product that may have been damaged in transportation,
storage or handling.
•Handle with care. Many KKDC products contain precision electrical components and are not designed to withstand excessive
stresses from tension or compression.
•Please follow standard ESD (Electrostatic discharge) protection measures when handling and installing KKDC LED products.
SAFETY AND WARRANTY
•Installation is only to be carried out by suitably qualified persons in accordance with installation instructions and all applicable
regulations or standards. (Improper installation can create an electrical hazard with risk of electric shock, fire or injury).
•KKDC will not be held responsible for any consequences arising from improper product handling, storage or installation.
•KKDC products must be installed as supplied. Disassembly, modification or attempted repair will invalidate warranty and may create
an electrical hazard.
•The KKDC product warranty is available with this document or in the following link:
http://www.kkdc.lighting/warranty-information.php on our website – www.kkdc.lighting.
PREPARATION
•Install KKDC products in accordance with the Wiring and Mounting instructions supplied with the product, using only the
recommended accessories, tools and fixings where specified.
•Product specification and installation information is also available from the KKDC website www.kkdc.lighting.
•Products should only be installed in areas appropriate to their IP rating, operable temperature and humidity range.
•Carefully plan and check the physical layout and circuit structure of the installation before starting work. Note wiring methods , cable
type and connection points along with positioning and rating of power supplies and any control gear.
Refer to all product information – including that for power supplies/control gear – and confirm choice of power supply, control gear,
cable thickness and cable length.
•For safe and reliable operation KKDC LED products must only be used with suitable KKDC supplied or recommended
power supplies and control gear. Contact KKDC for further information.
•These KKDC products require, 12V or 24V DC ‘constant voltage’ power supplies as specified for the LED products controlled.
AFTER INSTALLATION
•Ensure that paints, organic solvents and caustic or corrosive cleaning chemicals do not come into contact with KKDC products.
For example DO NOT USE –
- Benzene, Toluene, Xylene, Acetone, Carbon tetrachloride, Gasoline, Ether,
- Sodium/Calcium hydroxide, Sodium Carbonate.
•For cleaning or sanitization – products in sealed IP rated housings may be wiped with a soft cloth dampened with an alcohol cleaner
or with cool, soft water diluted (5% or less) bleach (Sodium Hypochlorite) solution.
•Please retain this information and pass to those responsible for installation/site maintenance.
Note:KKDC may change product specifications and installation guidance without prior notice.
See KKDC website for product document updates.
www.kkdc.lighting
OtherDMXProductsIG-01EN-20150703
DMX repeater
Control Gear
Installation Guide – Wiring
READ BEFORE INSTALLATION
•Cables used for connecting KKDC products must be of a suitable type and recommended gauge. Cable insulation must remain
undamaged and conductors free from dirt and corrosion.
•Control cables should be of a suitable shielded type and not xed in proximity to high voltage power cables or other sources of
electromagnetic interference.
•When connecting LED products always observe the correct polarity (+/-). Failure to do so may destroy the product.
•Electrical circuits should be wired with power off and all wiring and connections should be complete and checked thoroughly before
power is switched on. Take particular care not to confuse any control and power wiring. Do not remove any supplied product cable labels.
•Remove only the minimum of cable insulation necessary to make wiring connections to eliminate the possibility of short circuit.
•Cables should be joined with terminal blocks and adequately protected against water immersion or moisture ingress with suitable
tapes and sealants, potting compounds and IP rated junction boxes as appropriate to the installation and operating environment.
WIRING EXAMPLES
DMX repeater wiring
DMX input from DMX devices
9-24V input
9-24V
output
DMX output to DMX devices
DMX controller + visDIM DMX + KKRP-01 DMX repeater
(KKMC-01 or approved
DMX controller)
15m
RGB LED product
KKRP-01
#2
(T=DN)
visDIM DMX
sub-controller
RGB LED product
visDIM DMX
sub-controller
visDIM DMX
sub-controller
#1
(T=DN)
PSU
#32
#32 max
(T=UP)
RGB LED product
RGB LED product
PSU
PSU
12-24V DC PSU
#2
(T=DN)
visDIM DMX
sub-controller
#1
(T=DN)
visDIM DMX
sub-controller
visDIM DMX
sub-controller
15m
PSU
KKRP-01
#32 max
(T=UP)
RGB LED product
RGB LED product
PSU
#2
10m
#2
(T=DN)
visDIM DMX
sub-controller
RGB LED product
PSU
12-24V DC PSU
visDIM DMX
sub-controller
visDIM DMX
sub-controller
15m
10m
#1
(T=DN)
PSU
50m
KKRP-01
PSU
#1
PSU
12-24V DC PSU
RGB LED product
#32 max
(T=UP)
RGB LED product
CABLE PREPARATION
15mm
7mm
26 - 12 AWG
(0.5 -2.5mm2)
Note: This guide is produced from testing with KKDC approved power supplies or control gear.
Performance with other power or control products cannot be guaranteed. Contact KKDC for further information.
KKDC may change product specifications and installation guidance without prior notice.
See KKDC website for product document updates.
www.kkdc.lighting
DMXRepeaterWG-01EN-20150722
Product Warranty
In the unlikely event that purchasers should experience a product failure, this should in the first instance be dealt with by contacting the supplier or
local authorised KKDC representative.
Our warranty is provided in addition to any statutory legal rights and details the terms under which claims can be made.
1. Duration of Warranty
This warranty applies to all KKDC manufactured products for 3 years from the date of installation (or date of manufacture if the installation date is not
known or verifiable) An extended 5 year warranty may be offered at the discretion of KKDC if appropriate project registration criteria are met.
2. Repair or Replacement
Should a KKDC product fail to function within the warranty period, KKDC will on its sole discretion provide a replacement free of charge or repair
defective components in accordance with the terms set out below. Purchasers shall bear the cost of removal and return of any product subject to a
warranty claim and that of installing a replacement. Any other costs, including but not limited to replacement costs upon installation; costs caused
from failures of the installation or other damages and/or consequential damages are not covered by this warranty.
Replacement products shall as far as possible match the specification of the original but may have superior performance characteristics in line with
ongoing product development.
3. Return of a Defective Product
The purchaser making a warranty claim shall contact KKDC (or their authorised representative) at the earliest opportunity to be provided with an
address for return of the product. On receipt of returned product/s the validity of the claim will be checked. Proof of purchase may be required.
KKDC reserve the right to conduct diagnostic examination of any defective or failed product to determine patterns of usage and cause of failure and
reserve the right to be the sole judge as to whether a returned product is defective within the terms of this warranty.
4. Notes / Conditions of Warranty
This warranty applies only to defects in materials and workmanship and only where KKDC Products are properly handled, stored, installed, wired
and maintained in accordance with the most recent published KKDC product usage guides, installation instructions, specification sheets, and any
applicable local electrical safety standards and wiring regulations.
(The most recent versions of KKDC product documentation are available from the website www.kkdc.co.uk)
This warranty does not constitute any inference as to the suitability of any product for any purpose. In no event shall KKDC be liable for any other costs
or damages including lost profits, incidental, special or consequential damages.
Warranty claims will be invalid in the event of :
Product damage due to abuse, unauthorised alteration or modification, accident, fire, flood, lightning, rodents, insects, negligence or acts of God.
Product installation by unqualified persons.
Product modification, disassembly or attempted repair by non KKDC staff.
Product installation or storage in ‘abnormal’ conditions or locations, including but not limited to those where :
Ambient Temperatures are in excess of 60 Deg C.
Installation in areas of excessive humidity.
Any product subjected to excessive mechanical stress, or physical damage.
Inadequate heat sinking provision for any unhoused ‘bare PCB’ type LED product.
IP67 class luminaires installed without adequate local drainage, or becoming immersed in water.
Chemical contamination or damage from salt laden air.
Damage from use of pressure washers or other mechanical cleaners.
Improper use of ‘sanitizing products’ and maintenance using improper or unapproved chemical compounds/solvents.
Unauthorised use of parts or accessories not manufactured by KKDC in conjunction with KKDC Products.
‘Constant Voltage’ (CV) KKDC LED Products supplied with incorrect voltage.
‘Constant Current’ (CC) KKDC LED products supplied with incorrect current.
Incorrect layout, cutting and connection of wiring; intermittent or improper mains electrical supply.
Product/s having damaged serial number, cable or Certificate labels.
Product/s which have been installed more than once or have not been returned promptly and directly to KKDC for fault diagnosis and testing.
5. Warranty contacts
Warranty claims can be made only by the original purchaser by contacting KKDC or local KKDC authorised representative details of which can be
found via the supplier or on the website – www.kkdc.lighting.
6. Implied Terms
6.1 Subject to sub-clause 6.2, any condition or warranty which would otherwise be implied is excluded.
6.2 Where legislation implies any condition or warranty, and that legislation avoids or prohibits provisions in a contract excluding or modifying
the application of or exercise of or liability under such condition or warranty, the condition or warranty shall be deemed to be included in this
warranty. However the liability of KKDC for any breach of such condition or warranty shall be limited, at the option of KKDC, to the following:
If the breach relates to any KKDC Product:
(i) the replacement or the supply of equivalent KKDC Product;
(ii) repair of product (excluding costs of removal and installation);
(iii) payment of the cost of replacement or of acquiring equivalent product; or
(iv) payment of the cost of repair of product (excluding costs of removal and installation).
Note: KKDC reserves the right to make changes to product specifications and installation guidance without prior notice.
See KKDC website for product document updates.
www.kkdc.lighting
WRT-04EN-20150703
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising