Using smoke alarm detectors with free@home Integration of smoke

Using smoke alarm detectors with free@home Integration of smoke
Using smoke alarm detectors with free@home
Integration of smoke alarm detectors
GPG Building Automation
Doc.-Type:
Step-by-Step Guide
Doc.-Nr.
9AKK106930A5450
Department: Global Support
Author:
C. Bachenheimer-Schäfer
System:
free@home
Product:
free@home
Page:
1/7
Date:
19.01.2017
Doc.-Version:
1.1
Liability Disclaimer:
This document serves the sole purpose of providing additional, technical information and possible application
and use cases for the contained products and solutions.
It does not replace the necessary technical documentation required for planning, installation and
commissioning of the product. Technical details are subject to change without notice.
Despite checking that the contents of this document are consistent with the current versions of the related hard
and software of the products mentioned within, deviations cannot be completely excluded. We therefore assume
no liability for correctness. Necessary corrections will be introduced as and when new versions of the document
are generated.
.
Introduction
The following example described in this document helps in the creation of a smoke alarm detector function with
free@home. In the free@home system we want to network smoke detectors. When one of the detectors is
triggered, we want a light scene to be activated, e.g. “escape route – open blinds” and/or “Escape route
lighting”.
Objectives of the document
−
The purpose of this document is to provide guidance to the electrician and/or user by which he can set up a
small smoke alarm detector function with free@home.
Content
6834-84
6834-84 +
Binary input
BI-F-2.0.1
6241/2.0U
6834-84 + 6828
System Access
Point
Relay
6929-84
Power supply
Fig. 1: Overview diagram
Note:
− There must be at least one detector with radio module.
− Since the release of free@home 2.0 it is possible to send an additional e-mail or notification.
1. The smoke detector as well as the relay module are linked wirelessly, as described in the manual. The NO
contact is connected to the relay module’s binary input.
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
2/7
2. Drag the binary input into the floor plan, for example into the plant room. It serves as actuator there.
3. Create a light scene “Fire alarm”, during which the blinds shall move up and the lights shall light up.
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
3/7
4. Link the binary input with the light scene “Fire alarm”. Make sure you have DEACTIVATED the function
“Long press of the button > Retain scene”.
5. Since the release of free@home 2 you can also send a message via the actions screen.
Make sure that the binary input is not linked with a light scene. At this point, it is recommended to add the binary
input once more to the floor plan here.
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
4/7
6. Precondition with any desired period.
7. Add an event and select a channel. Select a binary input for the sensor.
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
5/7
8. The event shall be started upon “Activation” the device. It is possible to add an additional action later, which
defines the neutralization of the alarm.
9. Add an action and associate it with the previously created light scene “Fire alarm”.
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
6/7
10. Add a notification: When the action is triggered the system shall send a notification (e.g. e-mail or push
notification). You can create an individual text and subject line.
References to other documents
−
FAQ Home and Building Automation
−
FAQ free@home
−
Engineering Guide Database
© ABB
No liability for printing errors.
This version is from the 19.01.2017
Title:
Doc.-Nr.:
Author:
Page:
Using smoke alarm detectors with free@home
9AKK106930A5450
C. Bachenheimer-Schäfer
7/7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising