CAM5000 Installation Manual

CAM5000 Installation Manual
CAM5000
COLOR CCTV CAMERA
P R E -W
WIRE AND INSTALLATION INSTRUCTIONS
The CAM5000 Color CCTV Camera provides a
significant upgrade in performance in a smaller
package than the original CAM2010.
The CAM5000 features a miniature weather-tight
die-cast aluminum housing built to withstand the
harshest weather conditions. The camera can
rotate 360 degrees and pivot 90 degrees to
enable it to be mounted in virtually any position.
The flexible mounting bracket enables the dealer
to optimally adjust the viewing angle.
The camera's high-resolution, low lux 1/3" CCD
element provides clear images even in low light
conditions. Built-in automatic iris control ensures
an optimal picture on bright, sunny days without
"blooming" or "washouts". The fixed focal-length
lens has a horizontal viewing angle of 120
degrees with no "fish eye" distortion.
FEATURES AND APPLICATIONS
Extremely small size makes it easy to
conceal.
Auto White Balance enables true color
reproduction in varying light conditions.
Ideal for a wide variety of applications including residences, nurseries, storefronts,
swimming pool areas, boat docks, cabanas,
etc.
Outstanding video signal-to-noise ratio of
48dB for a noise-free picture.
Low power requirements ensure low heat
and long life.
MOUNTING THE CAM5000 AND
POWERING IT FROM A REMOTE
LOCATION
The CAM5000 includes a multi-purpose mounting bracket. This bracket enables the CAM5000
to be securely attached to almost any mounting
surface.
1. Use the appropriate hardware to securely
mount the CAM5000’s bracket to the desired
mounting surface.
2. Using the male RCA-to-female F adapter
included with the CAM5000, connect the
camera to your RG-6 or RG-59 coax cable.
3. Most installations will require the CAM5000
be powered from a remote location (i.e. the
main equipment location). To accomplish this:
a. Remove the power connector from the
power supply (included) and the
CAM5000 as shown in Figure 1 (other
side).
b. Strip back the insulation on the red and
black camera power wires and terminate
them to the 18/2 wire you have run to the
camera location - be sure to maintain
proper polarity on CAM5000, the 18/2,
and the remotely located power supply
(the included power supply’s white striped
lead is POSITIVE. NOTE: DO NOT
remove the CAM5000’s yellow (video)
RCA jack connector!
4. Screw the camera chassis to the mounting
bracket and aim the camera for optimum
coverage. NOTE: The camera is in its proper
position when its Power and Video cable is
located in the upper-right when viewing the
camera from the rear. See Figure 1 (other
side).
CAM5000 SPECIFICATIONS:
Imaging Element...........................................CCD
Lux....................................................0.5 minimum
Resolution.........................................380 TV lines
Horizontal Viewing angle...................120 degrees
Vertical Viewing angle.......................100 degrees
Video Output:..............................1V peak-to-peak
Video Output Impedance........................75 Ohms
Power Requirements..................12VDC @ 90mA
(power supply included)
Wiring Requirements......................RG59 or RG6
(for video) and 18/2 (for Power)
NOTE: Mounting hardware is included, but additional hardware may be required depending on
the desired mounting surface.
© ELAN Home Systems • 2002 • All rights reserved. 5/02
P/N 9890003
ELAN
HOME
CAM5000
SYSTEMS
INSTALLATION MANUAL
(Remove)
CAM5000
(REAR VIEW)
BLACK = ( - )
18/2 (for Power)
RED = (+)
12VDC
800mA
WHITE STRIPE
is POSITIVE (+)
MALE RCA-TO-FEMALE
F- CONNECTOR
RG-6 or RG59 COAX
To ELAN Z880
or ELAN MOD30000
Video Modulator
Figure 1
Limited Warranty
ELAN HOME SYSTEMS, L.L.C. ("ELAN") warrants equipment manufactured by it to be free from defects in materials
and workmanship for one (1) year from the date of purchase, with the exception of speakers and SVC AND MVC
Series volume controls, which have a five (5) year warranty, V•Series volume controls, which have a ten (10) year
warranty and the Z• Amplifiers, which have a two (2) year warranty.
If within the applicable warranty period above purchaser discovers such item was not as warranted above and
promptly notifies ELAN in writing, ELAN shall repair or replace the items at the company's option. This warranty shall
not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been installed by other than
an authorized ELAN installer, (c) to installed equipment which is not installed to ELAN's specifications, (d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall have been subjected to negligence, accident, or damage by circumstances beyond ELAN's control, including, but not limited to,
lightning, flood, electrical surge, tornado, earthquake, or any other catastrophic events beyond ELAN's control, or to
improper operation, maintenance or storage, or to other than normal use of service.
With respect to equipment sold by, but not manufactured by ELAN, the warranty obligations of ELAN shall in all
respects conform and be limited to the warranty actually extended to ELAN by its supplier. The foregoing warranties
do not cover reimbursement for labor, transportation, removal, installation, or other expenses which may be incurred
in connection with repair or replacement.
© ELAN Home Systems • 2002 • All rights reserved. 5/02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising