CERTIFICATE OF INSTALLATION

CERTIFICATE OF INSTALLATION
CERTIFICATE OF INSTALLATION - USER INSTRUCTIONS
Single Dwelling Unit Hot Water System Distribution
CF2RͲPLBͲ02ͲE
(Page 1 of 2)
Instructions to CF2R ͲPLBͲ02
A. Dwelling Unit Name
01 This identifies the dwelling unit on this form and is reference from the CF1R. One form is required for each dwelling unit in the building.
B.
Design
Central
Water
Heating
Systems
Information
This table reports the water heating system features that were specified on the registered CF1R compliance document for this project. For information only and requires no
user input.
Heating
Systems
Information
C.
Installed
Central
Water
This table reports the water heating system information that is being installed. Require one line for each central system.
01 Water Heating System ID or Name - Reference information from CF
Ͳ1R
system type are DHW, or Combined Hydronic
02 Water Heating System Type - Reference information from CF
Ͳ1R. The different kinds of water heating
03 Water Heater Type - Information from CFͲ1R. The different kinds of water heaters are Large Storage, Small Storage, Heat Pump, Boiler, Large Instantaneous, Small
Instantaneous or Indirect
04 # of Water Heaters in
system - Reference information from CF
Ͳ1R
05 Water Heater Storage Volume (gal) - User input. Value may be N/A if water heater type is instantaneous with zero storage..
06 Fuel Type - Reference information from CFͲ1R. The different kinds of fuel types are natural gas, propane, oil, or electricity.
07 Rated Input Type - Reference information from CF Ͳ1R. For natural gas, propane and oil fuel type the input type is Btu/Hr. For electric the input type is kW
08 Rated Input Value - User input. Numerical value of the rated input. Must be equal to or less than value indicated on the CFͲ1R
Ͳ1R. Different efficiency types are Energy Factor, AFUE, and
Thermal Efficiency
09 Heating Efficiency Type - Reference information from CF
10 Heating Efficiency Value - User input. Numerical value of the Heating Efficiency. Must be equal to or higher efficiency than value indicated on the CF Ͳ1R
11 Standby Loss - User input. Must be equal to or less than value indicated on the CFͲ1R. Value may be N/A if CFͲ1R value is N/A.
12 Exterior Insul. R ͲValue - User input. Must be equal to or higher than value indicated on the CF Ͳ1R. Value may be N/A if CF Ͳ1R value is N/A.
13 Central DHW System Distribution Type Ͳ Reference information from CFͲ1R
14 Dwelling Unit DHW System Distribution Type Ͳ Reference information from CFͲ1R
Water
Heater
Manufacturer
Information
D.
Installed
This table reports the manufacturer information of the installed water heater(s). Require one line for each installed water heater
01 Water Heating System ID or Name - Reference information from CF
Ͳ1R.
02 Manufacturer - User input. Enter the name of the water heater manufacturer.
03 Model Number - User input. Enter the model number of the water heater.
E.
MANDATORY
MEASURES
FOR
ALL
DOMESTIC
HOT
WATER
DISTRIBUTION
SYSTEMS
This table lists the requirements for all central recirculation systems. Installer must ensure all the requirements on this table are met.
CA Building Energy Efficiency Standards Ͳ 2013 Residential Compliance
June 2014
CERTIFICATE OF INSTALLATION - USER INSTRUCTIONS
Single Dwelling Unit Hot Water System Distribution
CF2RͲPLBͲ02ͲE
(Page 2 of 2)
F.
Standard
Distribution
System
Requirements
(trunk
and
branch
systems
only)
This table only applies to systems indicated in B14 and C14 as Standard Distribution System. In additional the mandatory requirements in Table E, the installer must ensure the
requirements on this table are met.
G.
Pipe
Insulation
Credit
Requirements
(For
trunk
and
branch
Hot
Water
system)
This table only applies to systems indicated in B14 and C14 as Pipe Insulation Credit. In additional the mandatory requirements in Table E, the installer must ensure the
requirements on this table are met.
H.
Parallel
Piping
Requirements
This table only applies to systems indicated in B14 and C14 as Parallel Piping. In additional the mandatory requirements in Table E, the installer must ensure the requirements
on this table are met.
I. Recirculation Non
Ͳdemand controls Requirements
This table only applies to systems indicated in B14 and C14 as Recirculation NonͲdemand controls. In additional the mandatory requirements in Table E, the installer must
ensure the requirements on this table are met.
J.
Demand
Recirculation
Manual
Control
Requirements
This table only applies to systems indicated in B14 and C14 as Demand Recirculation Manual Control. In additional the mandatory requirements in Table E, the installer must
ensure the requirements on this table are met.
K.
Demand
Recirculation
Sensor
Control
Requirements
This table only applies to systems indicated in B14 and C14 as Demand Recirculation Senor Control. In additional the mandatory requirements in Table E, the installer must
ensure the requirements on this table are met.
CA Building Energy Efficiency Standards Ͳ 2013 Residential Compliance
June 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising