GU10 Spotlights: - Eterna Lighting

GU10 Spotlights: - Eterna Lighting
MODELNO.
SPOT
Range
INSTALLATION INSTRUCTIONS
A guide for qualified electricians
SPOT3CRPL
SPOT1WHWC
Pack contents:
1 x Fitting
1 x Fixing kit
SPOT2SN
874/2012
SPOT3WHBAR
SPOT4SN
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” effective August 2005—UK
WEEE Regulations effective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST - DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Clean this light fitting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specific
instructions regarding individual installations.
GU10 Spotlights:
Single: SPOT1WHWC, SPOT1CRWC, SPOT1SNWC
Twin Bar: SPOT2WH, SPOT2CR, SPOT2SN
Triple Bar: SPOT3WHBAR, SPOT3CRBAR, SPOT3SNBAR
Triple Plate: SPOT3WHPL, SPOT3CRPL, SPOT3SNPL
Quad Split Bar: SPOT4WH, SPOT4CR, SPOT4SN
These instructions are provided as a guideline to assist you.
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Issue 0216
Visit our website: www.eterna-lighting.co.uk
Made in China
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this fitting
is fit for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service. Using
this fitting in any other environments may result in
a shortened working life, for example where there
is prolonged periods of use or higher than normal
ambient temperatures such as lighting public or
shared spaces or in nursing / care home facilities.
This light fitting must be installed in accordance
with the Building Regulations making reference to
the current edition of the IEE Wiring Regulations
(BS7671).
Switch off the mains before commencing installation
and remove the appropriate circuit fuse.
Suitable for indoor use only.
This product is only suitable for use in living areas
(not for areas constantly subject to moisture).
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current edition
of the IEE Wiring Regulations (BS7671).
This product is designed for permanent connection
to fixed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit. We recommend that the supply
incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation. Wrap any loose terminal blocks well with
insulating tape.
INSTALLATION:
1) Choose the location for your new spotlight
according to the conditions listed opposite.
2) L oosen the screws on either side of the back of
the fitting and turn the fixing strap clockwise and
remove it.
3) Using the fixing strap as a template, mark the
position of the fixing holes on your mounting
surface. If you are mounting your spotlight on a
wall, use a spirit level to ensure that the fitting is
level (if required).
4) S ecure the fixing bracket to the wall using the
fixings supplied. If the fixings supplied are not
appropriate to your installation, select suitable
alternatives. Take care not to trap your supply
wire.
5) M
ake the electrical connections according to the
colour code opposite.
6) O
ffer the fitting to the fixing strap, turn into
position and tighten the screws. Take care not to
trap any wires.
This product must be connected to Earth.
7) Fit the lamp (not supplied).
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specified in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
8) Restore the power and switch on.
LAMP REPLACEMENT:
Switch off the electricity at the mains.
Turn the lamp anti-clockwise and withdraw.
Insert new lamp, turn clockwise to the stop.
We do not recommend fitting spotlights in
bathrooms (due to the risk from broken glass if a
bulb breaks).
Restore the power and switch on.
This product is suitable for installation on surfaces
with normal flammability e.g. wood, plasterboard,
masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).
Requires 1 x 50W Max. 240V GU10 halogen or LED
lamp per lampholder (not included).
Before making fixing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new fitting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
The lamp must be positioned so that there is at least
0.5M (500mm) between the bulb and any illuminated
surface. Spotlights should be positioned well away
from curtains and beds to ensure this distance is
maintained.
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
REPLACEMENT LAMP TYPE:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising