Start Here Install GoContol Panel

Start Here Install GoContol Panel
START HERE
DO-IT-YOURSELF
SECURITY AND AUTOMATION PACKAGE
ESSENTIAL STEPS
HERE ARE SOME KEY POINTS YOU’LL WANT TO KNOW.
1. TEST YOUR SYSTEM
Press Security Menu Toolbox Enter 4 digit master code System Test. Then trigger each sensor to provide feedback at the panel.
2. ACTIVATE YOUR SYSTEM
After installing your system your 24/7 monitoring will not be activated until you call 1-877-826-5443 or email activations@linkinteractive.com.
You will receive an email providing you with the phone number for the monitoring center, your account number and password. You will
also receive an attachment to the email which contains a Certificate of Monitoring which you may provide to your insurance company in
order to receive any discounts offered.
Please note that if you do not install your system within 30 days from the ship date, we will automatically activate your system for you.
3. ADD LINK INTERACTIVE TO YOUR SAFE-SENDERS LIST
We will be communicating with you via email with information regarding your system. Please add the following email address to your
safe-senders list:
customerservice@linkinteractive.com
4. REGISTER YOUR ALARM SYSTEM WITH LOCAL AGENCIES
You may be required to register your new alarm system with your local police department, sheriff’s office or emergency agencies depending on your installation address. It is your responsibility to contact your local authorities to determine registration, permit or licensing
requirements. Failure to comply with the permitting requirements of your local authorities may result in a fine. Any fines or fees assessed to
Link Interactive for failing to comply with the permitting requirements will be charged in full to your customer account.
Please call with any questions: 877-826-5443 - M-F 7 a.m. to 8 p.m. and Saturday 8 a.m. to 4 p.m. - Mountain Time
5. REVIEWS AND REFERRALS
We love to read your reviews and want to know that you’re completely satisfied with our products and services. Please review us on Yelp,
Angie’s List, Google+, TrustPilot or the BBB.
Much of our business is grown through our customer’s referrals to friends and family. If someone you know orders a system from us and
lets us know you referred them, we’ll say ‘thank you’ by crediting both accounts with one free month of monitoring!
STOP! DO NOT RETURN EQUIPMENT TO RETAILER. CONTACT LINK FOR ALL PRODUCT RETURNS/WARRANTY QUESTIONS.
!
1-877-826-5443
!
Start Here:
Install Go!Control
Alarm Panel
For installation instructions for all other components go to
https://www.linkinteractive.com/installation-guide/
STEP 1
Remove your equipment from the shipping box. Open the
inner box that contains your alarm panel marked with the
green sticker. Do not plug your panel into an electrical outlet
at this time.
STEP 2
DESK MOUNT OPTION
With a small Phillips screwdriver, remove the screw on top of
the panel (fig 1). Insert a small straight screwdriver into the
slots and give a gentle quarter turn, releasing the back plate
(fig 2). Remove the AC barrel plug from panel, feed it
through the desk mount, back plate and reconnect to panel
and reattach back plate to panel (fig 3). Place the flat
antenna inside the desk mount. Snap the desk mount to the
back of the panel (fig 4).
fig 1
fig 2
WALL MOUNT OPTION
Make sure your desired location has a non-GFI wall outlet
nearby. With a small Phillips screwdriver, remove the screw
on top of the panel (fig 1). Insert a small straight screwdriver
into the slots and give a gentle quarter turn, releasing the
back plate (fig 2). Gently bring the antenna through the back
plate opening towards the panel. Using care not to break the
back plate, pop off the tabs in the wire channel guide on the
back and press the power cord into it. Mount the back plate
to the wall. Create a small hole in the wall directly behind the
small oval opening. Feed the antenna back through the
small oval opening and into the hole in the wall to allow the
antenna to hang freely inside the wall behind the back plate.
Mount the panel to the back plate by snapping it onto the
back plate and replacing the screw.
fig 3
STEP 3
Choose a central location for your alarm panel that is not
visible from outside your home. Plug the panel into an outlet
that is not a GFI or controlled by a switch, then wait approximately 30 seconds while it powers up and receives its
cellular connection
STEP 4
Change your panel’s default code from 1111 to a safer
master code. At the panel follow this sequence:
press Security press Menu press Toolbox
enter 1111 press User Management press Master User
press Change Pin 1111 enter new code press OK
enter new code again to confirm and press OK
press Home button.
STEP 5
For installation instructions for all other components go to
https://www.linkinteractive.com/installation-guide/
Note
You can enter up to 31 other user codes with optional operational
and expiration dates.
fig 4
Setting the Chime Feature
At the panel follow this sequence:
press Security > press Menu > press Toolbox
choose which item to set Chime for
press OK
press Home Button
press Chimes
choose Chime option
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising