automate - Total Window Concepts

automate - Total Window Concepts
AUTOMATE
Li-ion ARC TUBULAR MOTOR
433 MHZ
BI-DIRECTIONAL
ELECTRONIC
LIMIT
SELECTABLE
RPM
FAVORITE
POSITION
LEVEL CONTROL
WIREFREE
SOLAR
POWERED
AUTOMATE | Li-ion ARC motors offer a wirefree rechargeable easy to use and program
solution to suit a large range of applications, torques and speeds.
The Leveling Control feature allows for precise positioning of multiple shades ensuring
perfect alignment.
Additionally, a favorite position can be pre-set and recalled at any time.
FEATURES:
• Electronic Limits
• 433 MHz Bi-Directional RF Communication
INSTR. MTDCBRF V1.2 JUNE 2016
• Leveling Control
• 3 x Selectable Rpm
• Favorite Position
• Roller & Tilt Modes.
NOTES
2 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
CONTENTS
1ASSEMBLY
5
2WIRING
6
2.1 Charging options
6
3
P1 BUTTON FUNCTIONS
7
4
INTIAL SET-UP
8
4.1 Pair motor with controller
8
4.2 Check motor direction
8
4.3 Set limits
9
5
ADJUSTING LIMITS
10
5.1 Adjust upper limit
10
5.2 Adjust lower limit
10
6
11
ADDING OR REMOVING CONTROLLERS AND CHANNELS
6.1 Using motor P1 button
11
6.2 Using a pre-existing controller
11
7
12
FAVORITE POSITIONING
7.1 Set a favorite position
12
7.2 Send shade to favorite position
12
7.3 Delete favorite position
12
8
ADJUSTING MOTOR SPEED
13
8.1 Increase or decrease motor speed
13
9
14
TILT & ROLLER MODE
9.1 Enter tilt mode
14
9.2 Enter roller mode (Default)
14
10TROUBLESHOOTING
15
3 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
SAFTEY INSTRUCTIONS
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
CAUTION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not expose to moisture or extreme temperatures.
Do not allow children to play with this device.
Use or modification outside the scope of this instruction manual will void warranty.
Installation and programming to be performed by a suitably qualified installer.
For use within tubular blinds.
Ensure correct crown and drive adaptors are used for the intended system.
Keep antenna straight and clear from metal objects
Do not cut the antenna.
Use only Rollease Acmeda hardware.
Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.
Ensure torque and operating time is compatible with end application.
Do not expose the motor to water or install in humid or damp environments.
Motor is to be installed in horizontal application only.
Do not drill into motor body.
The routing of cable through walls shall be protected by isolating bushes or grommets.
Ensure power cable and aerial is clear and protected from moving parts.
If cable or power connector is damaged do not use.
Important safety instructions to be read prior to operation.
•
•
•
•
•
•
•
It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
should not be allowed to use this product.
Keep remote controls away from children.
Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
Keep motor away from acid and alkali.
Do not force the motor drive.
Keep clear when in operation.
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
4 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
1
ASSEMBLY
Please refer to Rollease Acmeda System Assembly Manual for full assembly instructions relevant to the hardware system being used.
Step 1. Cut roller tube to required length.
Step 2. Ensure roller tube is clean and free from burrs.
Step 3. Fit required crown, drive and bracket adapters.
Crown
Tube must be close fitting with chosen crown
and drive adapters. Refer to Rollease Acmeda
System Assembly Manual for recommended
crown, drive, and bracket adapter kits.
Retaining
Clip
Drive
Step 4. Slide Motor into tube.
Insert by aligning keyway in crown and
drive wheel to the tube.
Step 5. Mount motorized tube onto brackets.
Motor Head
Refer to Rollease Acmeda System
Assembly Manual for recommended crown,
drive, and bracket adapter kits.
Adapter
Bracket
5 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
2
WIRING
2.1 Charging options
This motor has a 12V built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 12.6V / 1000mAh.
•
Before first use please charge motor for 6 hours. Using the reccomended AC charger.
•
During operation, if voltage drops to less than 10V, the motor will beep 10 times to prompt it needs to be
charged.
•
Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is
greater than 7.5V.
AC Charger
ITEM NO.:
# MTDCB-CHARGE-US
# MTDCB-CHARGE-AU
# MTDCB-CHARGE-EU
Solar Panel
ITEM NO.:
#MTSOLPAN-B
Ensure cable is kept clear of fabric.
Ensure antenna is kept straight and away from metal objects.
6 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
3
P1 BUTTON FUNCTIONS
P1 Press
Short Press
Condition
Function Achieved
Visual
Feedback
Audible
Feedback
Function Described
If limit is NOT
set
None
No Action
None
No Action
If limits are set
Operational control
of motor, run to limit.
Stop if running
Motor runs
None
If motor is in
“Sleep Mode” &
limits are set
Wake and control
Motor wakes
and runs in a
direction
None
Hold P1
Operational control
of motor after pairing
and limit setting is
completed first time
Motor is restored from
Sleep Mode and RF
control is active
P1
Activate Pairing
Mode
Approx.
Motor Response
Sleep Mode
Approx.
Motor Response
Reverse
Direction
Approx.
Motor Response
Reset To Factory
Settings
Approx.
Motor Response
7 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
4
INTIAL SET-UP
4.1 Pair motor with controller
Select channel on
controller.
IMPORTANT
Hold P1 button on motor
head.
Hold STOP on controller.
Motor Response
Motor Response
Consult user manual for your
controller for information on
selecting channel.
Motor is now in step mode and ready for setting limits
4.2 Check motor direction
To check travel direction of shade, press UP
or DOWN on controller.
To reverse shade direction, hold both UP and
DOWN.
Quick Press = Step
Long Press = Continuous Travel
Motor Response
IMPORANT
Damage to shade may occur when operating
motor prior to setting limits. Attention should
be given.
IMPORTANT
Reversing motor direction using this method is only possible
during initial set-up.
8 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
4.3 Set limits
To save upper limit, hold UP and STOP.
Move shade to the desired highest or lowest
position by pressing the UP or DOWN buttons
on controller.
To save lower limit, hold DOWN and STOP.
IMPORTANT
Cycle shade up and down prior to setting limits to settle fabric
Motor Response
5 SECS
IMPORTANT
After setting limits, motor will automatically exit from initial
set-up mode.
Initial set-up is now complete
9 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
5
ADJUSTING LIMITS
5.1 Adjust upper limit
Hold UP and STOP on
controller.
Move shade to the desired
highest position by
pressing the UP button.
Motor Response
To save upper limit, hold
UP and STOP.
Motor Response
5 SECS
5 SECS
5.2 Adjust lower limit
Hold DOWN and STOP on
controller.
Move shade to the
desired lowest position
by pressing the DOWN
button.
Motor Response
5 SECS
10 | Automate Programming Instructions | Tubular Li-ion Motors
To save lower limit, hold
DOWN and STOP.
Motor Response
5 SECS
ROLLEASE ACMEDA
6
ADDING OR REMOVING CONTROLLERS AND CHANNELS
6.1 Using motor P1 button
Hold P1 button on motor head.
Hold STOP on controller to add or remove.
Motor Response
Motor Response
6.2 Using a pre-existing controller
Press P2 on existing
controller.
Motor Response
IMPORTANT
Consult user manual for your
controller or sensor.
Press P2 on existing
controller.
Motor Response
Press P2 on new
controller.
Motor Response
7
FAVORITE POSITIONING
7.1 Set a favorite position
Move shade to the desired position by pressing the UP or DOWN button on the controller.
Press P2 on controller.
Motor Response
Press STOP on controller.
Press STOP on controller.
Motor Response
Motor Response
7.2 Send shade to favorite position
Hold STOP on controller.
7.3 Delete favorite position
Press P2 on controller.
Motor Response
Press STOP on controller.
Press STOP on controller.
Motor Response
Motor Response
12 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
8
ADJUSTING MOTOR SPEED
8.1 Increase or decrease motor speed
Press UP.
Press UP.
Press DOWN.
Press DOWN.
Press P2 on controller.
Motor Response
Motor Response
Motor Response
IMPORTANT
If motor does not react to speed
adjustment, the maximum or
minimum speed has already been
reached.
13 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
9
TILT & ROLLER MODE
9.1 Enter tilt mode
Hold UP and DOWN on controller.
Press STOP.
Motor Response
Motor Response
5 SECS
9.2 Enter roller mode (Default)
Hold UP and DOWN on controller.
Motor Response
Press STOP.
Motor Response
5 SECS
10
TROUBLESHOOTING
Problem
Motor is not responding
Motor beeps 10 times when in use
Cause
Remedy
Battery in motor is depleted
Recharge with compatible AC
adaptor and check connection and
positioning of PV panel.
Insufficient charging from Solar
(PV) Panel
Check connection and orientation
of PV panel.
Transmitter battery is discharged
Replace battery
Battery is inserted incorrectly
into transmitter
Check battery polarity
Radio interference/shielding
Ensure transmitter is positioned
away from metal objects and the
aerial on motor or receiver is kept
straight and away from metal
Receiver distance is too far from
transmitter
Move transmitter to a closer
position
Power failure
Check power supply to motor is
connected and active
Incorrect wiring
Check that wiring is connected
correctly (refer to motor
installation instructions)
Battery voltage is low / PV (solar)
panel issue
Recharge with AC adaptor or check
connection and positioning of PV
pane
Always reserve an individual
channel for programming
functions
Cannot program a single Motor
(multiple motors respond)
Multiple motors are paired to the
same channel.
SYSTEM BEST PRACTICE - Provide
an extra 15 channel remote in your
multi motor projects, that provides
individual control for each motor
for programming purposes
Place all other motors into sleep
mode (ref to P1 function overview
- section 3)
15 | Automate Programming Instructions | Tubular Li-ion Motors
ROLLEASE ACMEDA
ROLLEASE ACMEDA
AUSTRALIA
110 Northcorp Boulevard,
Broadmeadows VIC 3047
T +61 3 9355 0100 | F +61 3 9355 0110
Western Australia Branch
Unit 1, 41 Mulgul Road,
Malaga WA 6090
T +61 8 9248 5571 | F +61 8 9248 5572
ROLLEASE ACMEDA
USA
200 Harvard Avenue
Stamford, CT 06902 6320
T +1 203 964 1573 | F +1 203 964 0513
ROLLEASE ACMEDA
EUROPE
Via Conca Del Naviglio 18, Milan
(Lombardia) Italy
T +39 02 8982 7317 | F +39 02 8982 7317
info@rolleaseacmeda.com
rolleaseacmeda.com
16 | Automate Programming Instructions | Tubular Li-ion Motors
Queensland Branch
Unit 2/62 Borthwick Avenue,
Murarrie QLD 4172
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising