Tactical Power and Specialty Solutions - Power Solutions

Tactical Power and Specialty Solutions - Power Solutions
Tactical Power and
Specialty Solutions
power.apitech.com
Section 1
Expeditionary Specialty Solutions
Section 3
Section 2
Power Distribution for Ground and Mobile
System Solutions for the Field
Custom Solutions
TPS Tactical Power Supply Series
Weatherproof Power Supply with Battery Charger and Remote Monitoring and Control
PART - 7200-A-161-RC
The API Technologies TPS Tactical Power Supply Series by API Technologies is a
expeditionary commercial-off-the-shelf (COTS) solution designed to power C4ISR
systems, critical electronic warfare(EW) and weapons equipment. The TPS features
weatherproof & ruggedized construction which allows it to withstand extreme
temperature and harsh environments. When fielded, the TPS supports powering
fielded special ops equipment reducing vehicle wear and tear and fuel consumption.
The TPS converts AC power from generators or community power and converts
power to 28 VDC power at a variety of amperages (150A, 100A, and 75A models).
Source power of AC can be one of three different AC inputs.
• 1 x Three Phase WYE, 208/120 VAC
• 1 x Single Phase, 240/120 VAC Mid-Point Neutral
• 3 x Single Phase, 100-127 VAC
Features
AC INPUT:
1 x Three Phase WYE, 208/120 VAC
1 x Single Phase, 240/120 VAC
Mid-Point Neutral
3 x Single Phase, 100-127 VAC
DC OUTPUT: 28 VDC @ 10 A
Integrated battery charger;
28 Volts of DC power at 10A;
Battery detect feature to ensure
connection and state of charge;
Reverse polarity protection
included;
The reverse polarity protected battery charger provides 28 Volts of DC power at 10
2
Amps to a connected battery. The battery detect feature identifies when a battery is
connected and determines state of charge and float charges the battery to 100% for
immediate crank-ready state.
Withstands extreme temperatures,
shock and vibration; Weatherproof
and water resistant housing; Meets
MIL-STD 810
The TPS has a built-in “soft start” feature, circuit protection, and transient voltage
suppression. Integrated forced air cooling and heat sinks aid in heat dissipation while
automatic over-temperature shut down to protect the TPS and critical loads. Manually
check status of AC inputs, DC output, LAN connection, Transient Voltage Suppression
(TVS), battery charger, and temperature with the “push to view” status indicator
button on the front panel.
Remote monitoring with user
enabled remote ON/OFF for the
DC outlet and the battery charger.
Alarm limits creation for line input
voltage, and more. Telnet and Web
Interface communication and
monitoring protocols.
The TPS provides remote monitoring via communication and monitoring protocols
include Telnet, SNMPv2, and Web Interface. Users can remotely turn the DC outlet
on/off, get the battery charger status, create alarm limits DC Voltage and monitor the
voltage and current status.
EMI filtering protecting against
noise and interference is compliant
to MIL-STD 461
2
Transient voltage and circuit
protection
Technical Specifications (7200-A-161 and 7200-A-155)
Item
Specification
AC Power Entry Connector
MIL-DTL-5015, 28-1P Locking Bayonet Connector
Input Power Single connector permits three
types of input power
1 x Three Phase WYE, 208/120 VAC
1 x Single Phase, 240/120 VAC Mid-Point Neutral
3 x Single Phase, 100-127 VAC
Input Frequency
47 - 63 Hz
Input Current
20A/Line @ Full Load
Overload Protection
25A/3P Circuit Breaker, Flat Rocker Style
DC Output Connectors
MIL-DTL-5015
32-5S Locking Bayonet Connector
Communication Interface
10/100 BaseT Ethernet
Network Interface
TCP/IP, Telnet, SNMPv2, HTTP, Web
Push to View Status Indicators
AC Power Input, DC Power Output, Battery Charger, LAN, High Temperature,
Transient Voltage Suppression (TVS)
Battery Charger
28VDC@10A bulk charging capacity MIL-DTL-5015, 16-11S locking bayonet connector Intelligent
battery charging Reverse polarity protection
Operating Temperature
-40°F (-40°C) to 140°F (60°C)
Cooling
Integrated Forced Air Cooling
Humidity
Humidity: 0 to 95% (Non-condensing)
Elevation
Elevation: 15,000 ft (4,572 meters)
Storage Temperature
-40°F (-40°C) to 140°F (60°C)
Humidity
Humidity: 0 to 95% (Non-Condensing)
Elevation
Elevation: 32,808 ft (10,000 meters)
Mechanical Characteristics
Enclosed, Waterproof Chassis Rugged construction designed per MIL-STD 810
Remote Monitoring
AC Line Input Voltage; DC Output Voltage; DC Output Current; Operational Status
Remote Control
DC power output On/Off; battery charger On/Off
P/N
Output Voltage
Output Current
Weight 1
Dimensions1
7200-A-155
150 A @ 28VDC
4200 Watts
85 lbs
17” W x 17.475” H x 13” D
7200-A-161
75 A @ 28VDC
2100 Watts
55 lbs
13.75” W x 11.5” H x 12” D
Note 1: Optional Mounting Brackets and Roll Cage Change Dimensions & Weight
Maximum Operating
Ranges
7200-A-155
7200-A-161
175 A
150 A
Product Designed to Meet
MIL-STD Environment
Standards
150 Amps @ -40 to 40°
125 A
100 A
75 A
75 Amps @ 60°
75 Amps @ -40 to 50°
50 Amps @ 60°
50 A
Maximum operating ratings in
chart are for AC input configuration:
three-phase 4 wire WYE,
190-220 L-L VAC
+1 888.588.3448
powersales@apitech.com
25 A
(C°)-40°
(-40 F °)
0°
40° 50° 60° (C °)
20°
Ambient Temperature
3
(140 F °)
•
•
•
•
•
•
•
•
Water Resistant
Thermal Shock
Salt & Fog
Blowing Sand & Dust
Fungus
Mechanical Shock & Vibration
Ground Bond
MIL STD 810 & 461
PART - 7200-A-161
with the roll cage
and cables
Cable Accessory Information
for the TPS75
input connector
+1 888.588.3448
powersales@apitech.com
PART - JB-155
Junction Box with Cables
Available Options
Portable TPS are available with or without
features such as: Battery Charger, Remote
Communications, EPO (Emergency Power Off),
Roll Cage, Cable Sets, Junction Box, and more...
4
Military Applications
• Expeditionary Power
• Special Operations
• C4ISR
• Ground System Shelters
• Mission Control Shelters
• Satellite Communication (SATCOM)
• UAV Ground Stations
• Transit Cases
• Simulation and Training Shelters
• Network Infrastructure
• Forward Operating Base (FOB)
• Tactical Operations Center (TOC)
• Automated Test Equipment (ATE)
• Airborne (400Hz Models)
• Ground Radar Platforms
Rev: 09/18/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
5
www.apitech.com
Junction Box, Tactical Temporary PDU
Weatherproof Power Distribution Unit
PART - RC-JB155
The Junction Box or “Turtle” Series by API Technologies is a portable commercial+off-the-shelf (COTS) solution designed for distributing power from a TPS75 series
power supply supporting command & control communications systems and other
critical electronic warfare(EW) & weapons equipment. The Junction Box features
weatherproof & ruggedized construction which allows it to withstand extreme
temperatures (-40°C to 85°C) and harsh environments including shock, vibration,
and water spray. When fielded, the Junction Box, working together with the TPS75,
reduces fuel consumption and wear and tear on vehicles by eliminating run time to
support powering fielded special ops equipment.
Features
(4) 28 VDC outputs
Battery Charger Pass-Through
when using the TPS75 or TPS155
and the appropriate cable
Withstands extreme temperatures,
shock and vibration; Weatherproof
and waterproof housing; Meets
MIL-STD 810
EMI filtering protecting against
noise and interference is compliant
to MIL-STD 461
Transient voltage and circuit
protection
6
Technical Specifications JB155 Junction Box
Item
Specification
DC Input Characteristics:
Voltage
28VDC
Current
150A DC Input
Current
10A Battery Charger
Input Connector
MIL-DTL-5015, 32-15P Threaded Coupling
Circuit Protection
None
DC Output Characteristics J1:
Voltage
28VDC
Current
75A DC
Battery Charger Current
10A
J1 Output Connector
MIL-DTL-5015, 24-12S Locking Bayonet
Circuit Protection:
1P75A UL489 Circuit Breaker
DC Output J2-J4
Voltage
28VDC
Current
50A
J2-J4 Output Connector
MIL-DTL-5015, 24-12S Locking Bayonet
Circuit Protection
1P50A UL489 Circuit Breaker
Mechanical and Environmental Characteristics:
Material
Aluminum Enclosed, Waterproof Chassis
Operating Temperature
-40F (-40C) to 140F (60C)
Operating Humidity
0 to 95% (Non-Condensing)
Elevation
15,000 Ft. (4,572 meters)
Storage Temperature
-40F (-40C) to 185F (85C)
Storage Humidity
0 to 95% (Non-Condensing)
Storage Elevation
32,808 Ft. (10,000 meters)
Compliance
MIL-STD-810G
Military Applications
PART - JB155
Junction Box with Cables
PART - 7200-A-161
with the roll cage
and cables
• C4ISR
• Common Ground System Shelters
• Mission Control Shelters
• Satellite Communication (SATCOM)
• UAV Ground Stations
• Transit Cases
• Simulation and Training Shelters
• Network Infrastructure
• Forward Operating Base (FOB)
• Tactical Operations Center (TOC)
• Automated Test Equipment (ATE)
• Airborne (400Hz Models)
• Ground Radar Platforms
Available Options
Portable TPS75 Tactical
Power Supply can be paired
with the Junction Box and are
available with or without features
such as: Battery Charger, Roll Cage,
Cable Sets, and more...
Rev: 09/18/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
7
www.apitech.com
PEP Portable Power Entry and Export Panels
10KW AC Distribution Powered by Shore (Community) and Onboard Inverter with Battery
Charger and Transfer Switch
PART - 7200-A-126
The API Technologies Tactical PEP Portable Power Entry and Export Panel with
Transfer Switch is a 10KW AC Power Panel designed to support expeditionary “On the
Move” and “At the Halt” continuous power needs of the soldiers in the field. Designed
to be integrated in vehicles, shelters or mission cases, the PEP will work in conjunction
with a variety of power sources and has been tested for environmental durability;
meeting the Military desired wide operating temperatures from -46°C to 60°C and
MIL-STD-810.
While in the vehicle, a 3 Phase 208 VAC Inverter plugged into the AUXILIARY input
power connector enables the system to support a complete mission package
containing SIPRNET and NIPRNET suites to operate while “On the Go”. While
stationary, the PEP can be transferred quickly to a generator or community power
by connecting to the second MAIN input connector. The system can quickly discern
that a primary power source has been made available. When confirmed to be a good
source, the transfer switch in the power panel sends a signal to disconnect from the
Inverter and immediately connect to the generator or community power. This transfer
takes place in less than 17mSec. The PEP can be used in a fielded state not mounted
to a vehicle and operate effectively in any 3 phase power environment.
This Power Panel features 5 AC outlets with circuit breakers protecting the panel
and its associated loads. To provide flexibility while embedded in the vehicle or
mission case a Monitoring system complete with LAN access for Telnet and SNMP
communication has been provided for easy user visibility.
Dual AC Power Input:
3Ø 208V 30 Amps per phase shore
power or inverter vehicle power
5 AC Power Outputs:
4 x 120 VAC @ 20 Amps, 1 @ 30 Amps
AC Solid State automatic transfer
switch transfers power in less
than 17mSec
28 VDC @ 10A Battery Charger
Monitors 3Ø Output Voltage &
Current; Power Source Utilized:
Mains, Aux, None; Temp and voltage
threshold settings; Circuit Breaker
Status; Alarm/Warnings and More
Remote control through LAN
10/100 TCP/IP, Telnet, SNMPv2
Rugged Construction that meets
water fording requirements
Elapsed time indicator
EMI filtering to protect against noise
and interference
8
Transient voltage and circuit
protection
Technical Specification 7200-A-126
Item
Specification
Input Power
208/120 3Ø WYE VAC 47-63Hz, 30A
MAIN (J1): shore power at the halt
AUXILIARY (J5): vehicle inverter on the go
Input Power Monitoring
(Main & Aux Power)
Over-Voltage Detection
Under-Voltage Detection
Power Must Comply to both OV & UV for at Least 5 Seconds Prior to Power Transfer Occurring
Output Power
4 x 120 VAC @ 20A 47-63Hz
1 x 120 VAC @ 30A 47-63Hz
Battery Charger 28 VDC @ 10A
Overload Circuit Protection
UL489 Electromagnetic Circuit Breakers
Automatic Transfer Switch (ATS)
3Ø Solid State construction
•
•
•
•
Source Transfer Time < 17mSec (Clean sine wave to clean sine wave)
Front panel LEDs indicate voltage source availability
Transfer occurs only if sources comply with the transfer protocol
Once a transfer occurs to inverter or main, the ATS remains at either inverter or
main for 5 seconds before initiating another transfer.
Power Filtering
High Performance EMI/RFI L-G and N-G Filtering
Transient & Voltage Surge Suppression
Metal Oxide Varistors are Utilized, L-G, N-G, L-L, L-N; Energy Absorption: 215 Joules
Indicators
Elapsed Time Indicator; Push to test A Phases, B Phases, C Phases; Battery Charger; LAN; Temp.
Network Interface & Firmware
Standard IEEE 802.3
10/100 Base T: Telnet & SNMP
Networking Function Monitors
Battery Charger
Physical and Environmental
•
•
•
•
•
•
•
Three Phase Output Voltage & Current
Power Source Utilized: Mains, Aux, None
Internal temp & Hi temp threshold settings
Surge arrestor status
Circuit Breaker Position Status
Hi & Lo Voltage Threshold Settings
Alarm/Warning for Voltage, Current, Temp, and More
Dual Level, Battery State-of-Charge (SOC) Operation
Bulk Charge Current @ 10 Amps
Charger will Deliver Inverter Standby Current while Providing Charge Current to the Battery Dependent on Battery State-of-Charge (SOC)
Meets MIL-STD 810F Environmental Standards
Operating Temp
-46˚C to 60˚C
Dimensions
7.313” H x 20.5” W x 18.61” D
Weight
62 lbs
Military Applications
• Command Post Platforms
• Shore and Onboard Tactical Vehicle
Power Distribution
• Defense Mobile Command Vehicles
• Unmanned Vehicles & Vessels
• Mobile Command Posts
• Tactical Operations Centers
• Towed Radar Platforms & Generator
Platforms
• Transit Case for “MEP”
+1 888.588.3448
powersales@apitech.com
power.apitech.com
Rev: 09/17/14
9
www.apitech.com
PEP Power Entry and Export Panels
Wide Operating Temperature Input/Output Power Interface with AC & DC Shore and
Onboard Power Distribution for Command Post Platforms
PART - 7200-A-125
The API Technologies PEP Power Entry and Export Panel is designed for
Command Post Platforms to distribute onboard vehicle power as well as shore
power. This ensures reliable power to critical communications and telemetry
equipment with minimal downtime and optimal performance.
This Power Panel offers ideal Input/
Output (I/O) power and features both
+24/28 VDC (5.6 kW) @ 200 Amps and
3 Phase AC (21.6 kW) @ 60 Amp per
Phase I/O distribution capability. The
power panel also includes a 3 Phase
60 Amp pass through connector
interface to support additional forward
operating base requirements.
The panel has been tested for
environmental durability, Army required
wide operating temperature, and
MIL-STD 461E. The PEP is capable
of performing in temperatures from
-46°C to 60°C, and able to withstand
shock, vibration, water exposure, high
concentrations of sand, dust, salt fog,
and meets the Army performance
requirements of MIL-STD 810.
Input: 208/120 VAC, 3 Phase 60A
Output: 3 x 208/120 VAC, 3 Phase,
60A, 30A, 25A and 1 x 120 VAC
Single Phase , 15A
Input: 24 VDC at +200 Amps and
28 VDC at -200 Amps
Output: 28 VDC @ 35 Amps
+28 VDC @ 5A Battery Charger
Internal relay over voltage detection
and under voltage detection
Emergency Power Off; Kill switch
controlled externally
Tested for MIL-STD 810F
Environment Standards
Rugged Construction that meets
water fording requirements
“Push to View” status indicators
EMI filtering for both AC and
DC to protect against noise and
interference
The panel is a reliable fault protected
power distribution system capable of
preventing damage to critical mission
sensitive data and communication
hardware in the shelter or
tactical vehicles.
Transient voltage and circuit
protection; Surge protection on
all power lines
10
Technical Specification 7200-A-125
Item
Specification
Input Power
from generator or shore power
208/120 VAC, 3Ø 60Hz, 60A; Power Supply +28 VDC -200A; HMMWV Battery - 200A
Output Power
Battery Charger Power
+28 VDC
Export Power
208/120 VAC, 3Ø, 60Hz, 60A
Environmental Control Unit Power:
208/120 VAC, 3Ø, 60Hz, 30A
DC Power Supply
208/120 VAC, 3Ø, 60Hz, 25A
GCFI Power Outlet (Optional)
120 VAC, 1Ø, 60Hz, 15A
PTIP
120 VAC, 1Ø, 60Hz, 15A and +28 VDC, 35A
Shelter Config. Specifics Avail.
Overload Circuit Protection
UL489 Electromagnetic circuit breaker
Input AC Voltage Monitoring
Over-Voltage Detection
Under-Voltage Detection
Power Filtering
High Performance EMi/RFI L-G and N-G Filtering
Transient & Voltage Surge Suppression
AC Line Suppression
DC Line Suppression
Shelter Power
AC: 208/120 VAC, 3Ø, 60Hz, 60A DC: +28 VDC, 200A
Physical and Environmental Specifications
Operating Temperature
-46˚C to 60˚C
Dimensions
13.13’’ H x 13.38’’ W x 16.10’’ D
Weight
72 lbs
Military Applications
• Command post platforms
• Shore and onboard tactical vehicle
power distribution
• Defense mobile command vehicles
• Unmanned vehicles & vessels
• Mobile command posts
• Communications & telemetry cases
• Towed radar & generator platforms
Rev: 09/17/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
11
www.apitech.com
AC Power Master PDU Series
High Powered Three Phase Power Distribution Units with Sequencing, Overload & Circuit
Protection, and Remote Power Monitoring
PART - 7200-A-131-2
The API Technologies 3 Ø AC Power Master (ACPM) series delivers great value
in the versatility it provides. These high powered devices have a wide variety of
available configurations, multiple outlets that can be all different power outputs,
and many different communication protocols for monitoring, sequencing and fault
management.
The 3 Ø (Phase) ACPM series of PDUs minimize inrush currents that avoid nuisance
system tripping utilizing power sequencing and fault management solutions. The
ACPM effectively distributes 3 Ø (Phase) source power to multiple system loads
supporting a variety of customer applications.
The ACPM is available in versions that provide remote monitoring and remote power
cycling for those hard to get to locations. The benefit of remote monitoring is having
the ability to take action to avoid unintended power interruption and reduce the
threat of downtime.
The ACPM are designed for the industry standard 19 inch rack. Most models are 4U
tall with optional mounted slide rails for easy accessibility.
Features
AC INPUT/OUTPUT
3 phase power with phase
detection and phase correction
Power Sequencing and outlet
sequencing to minimize inrush
currents avoiding nuisance
system tripping
EMI filtering to protect against
noise and interference from other
electronic devices.
Transient voltage and circuit
protection
7200-A-131-2
Wide operating temperature
range that meets MIL-STD
requirements; auto temperature
shutdown
LAN Control
7200-A-131
12
Web Interface Monitoring Page for the 7200-A-131-2
Remote monitoring frequency,
phase voltage, Phase sequence
detecting, line current,
temperature and more
Internal and External Temp.
monitoring with Shut down
conditions, warnings, and alarms
Emergency Power OFF
Elapsed time indicator
Digital LED Status Indicators
This product can be modified in
color, shape, outlet style (NEMA
or IEC), power inputs, and more.
Technical Specifications
Part
Number
Input
Voltage
Max
Current
Output
Voltage
Physical
Dimensions
(W x D x H) in.
Sequencing
7200-A-135-1
3 Ø WYE, 208 VAC 50/60 Hz
70A Max/Phase
208 VAC - 3 Ø (3 x L21-30R)
208 VAC (3 x C19)
120 VAC (4 x C13)
19 x 24 x 6.95
No
N/A
No
7200-A-135-2
3 Ø WYE, 208 VAC 50/60 Hz
70A Max/Phase
208 VAC - 3 Ø (3 x L21-30R)
208 VAC (3 x C19)
120 VAC (4 x C13)
19 x 24 x 6.95
No
N/A
No
7200-A-135-3
3 Ø Δ, 208 VAC 50/60 Hz
60A Max/Phase
208 VAC - 3 Ø (3 x L15-30R)
208 VAC (3 x C19)
208 VAC (3 x C13)
19 x 24 x 6.95
No
N/A
No
7200-A-131
3 Ø WYE, 208 VAC 60 Hz
60A Max/Phase
208 VAC - 3 Ø (1 x L21-30R)
120 VAC (3 x L5-30R)
120 VAC (8 x 5-20R)
19 x 28.75 x 6.95
Yes
Telnet
TCP/IP
SNMPv2
Yes
7200-A-131-001A
3 Ø WYE, 200-240 VAC
50/60 Hz
80A Max/Phase
200-240 VAC 3 Ø (3 x L21-30R)
100-120 VAC (1 x L5-30R)
100-120 VAC (4 x 5-20R)
19 x 28.75 x 6.95
Yes
Telnet
TCP/IP
SNMPv2
Yes
19 x 20 x 6.95
Yes
Telnet
SNMPv2
Web
Yes
Com.
EPO
7200-A-131-2
3 Ø WYE, 208 VAC 50/60 Hz
60A Max/Phase
208 3 Phase:
(1) L21-30R, (1) L21-20R 120
Single Phase:
(9) L5-20R, (1) L5-15R
7200-A-49
3 Ø WYE, 208 VAC 60 Hz
70A Max/Phase
208 VAC - 3 Ø (1 x L21-30R)
120 VAC (3 x L5-20R)
120 VAC (8 x 5-15R)
19 x 28.75 x 6.95
Yes
RJ422
RJ435
Yes
7200-A-146
3 Ø Δ, 208 VAC 400 Hz
40A Max/Phase
208 VAC - 3 Ø Δ 6 x Switching
MIL-DTL-5015 2 x Unswitched
MIL-DTL-5015
19 x 20 x 5.19
No
Telnet,
SNMPv2
Web
No
7200-A-154
3 Ø WYE 208VAC 50/60 Hz
70A Max/Phase
208 VAC - 3 Ø (2 x MIL-DTL-5015)
208 VAC (2 x MIL-DTL-5015)
120 VAC (1 x MIL-DTL-5015)
19 x 24 x 6.95
No
N/A
No
+1 888.588.3448
powersales@apitech.com
13
Military Applications
• C4ISR
• Common Ground System Shelters
• Mission Control Shelters
• Satellite Communication (SATCOM)
• UAV Ground Stations
• Transit Cases
• Simulation and Training Shelters
• Network Infrastructure
• Forward Operating Base (FOB)
• Tactical Operations Center (TOC)
• Automated Test Equipment (ATE)
• Airborne (400Hz Models)
• Ground Radar Platforms
Satellite Communication (SATCOM)
Available to Meet MIL-STD
810 Standards
Transit Cases
• Thermal Shock
• Salt Fog
• Blowing Sand & Dust
• Fungus
• Mechanical Shock & Vibration
• Ground Bond
• MIL-STD-1686C ESD Control
• MIL-STD-461E EMC Compliance
Commercial Applications
• Medical Equipment Testing
• Test & Training’s ATE Centers
• Test Instrumentation for
Wafer Fabrication & Laser
Triming Applications
• Industrial Automation & Control
• Locomotive and Light Rail Transit
• Testing & Simulation Equipment
• Communication Equipment
• Server Rack Systems
+1 888.588.3448
powersales@apitech.com
14
Custom design collaboration is a hassle-free experience for customers.
Clients can work directly with our design team which helps reduce the design phase of the project. The experienced design team
at API Technologies has a proven track record for developing complex solutions within limited time frames. Advanced technology
is employed for a comprehensive system review of packaging preparation and manufacturability.
All products are tested for agreed upon electrical, mechanical, and environmental metrics. We administer our test procedures
not only for prototypes, but for each and every power product we manufacture. This focus on quality and reliability is part of the
commitment we make to our customers.
Optional Features & Benefits
• Single Phase or Three Phase
• Rack Mount & Non-Rack Designs
• Remote Monitoring & Control
• Remote Power Cycling/Sequencing
• Monitor: Frequency, Phase Voltage,
Line Current, Temperature, more.
• Power Quality Monitoring
• Rugged Field Packaging
• Phase Sequence Detection
with Phase Correction
• Wide Operating
Temperature Range
• Variety of Outlets & Plugs
(IEC, NEMA, MIL, and more)
• Up to 70 Amps/Phase Current
• Circuit Protection with
UL-Listed Breakers
• Transient Voltage Suppression
• Breaker On/Off/Reset
• Safety Lock-Out During Config
• Local Power Meter
• Battery Charger
• Automatic Transfer Switch (ATS)
• Digital LED Status Indicators
• Emergency Power Off (EPO)
• Elapsed Time Indicator
• EMP Protection
• EMI Filtering
• Common Mode &
Differential Mode Filtering
• Units up to 70 Amps/Phase
• Units up to 400Hz
http://power.apitech.com/custom-three-phase.aspx
Rev: 09/18/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
15
www.apitech.com
DC SMARTStart® Power Distribution Series
DC Switched Power Distribution with True Remote Cycling Capability:
Available in -48 or +24/+28 VDC
PART - 7832S60
The API Technologies DC SMARTStart® power distribution unit (PDU) with circuit
protection reliably cycles -48 VDC or +24/+28 VDC input power to devices with
DC power supplies. The DC Switched PDU uses specialized electronic switchable
solid state breakers to provide a true remote power cycling capability. To minimize
downtime, the breaker auto reset function can be activated. Then the on-board
SMARTStart® computer will pole the tripped channel position to determine whether
there is a fault, such as a short circuit. If this condition is determined to be non
catastrophic, the breaker is reset. The unit also features integral circuitry to provide
LVD and OVD protection automatically.
Using a visual basic interface, an operator can power cycle all 12 solid state breakers
as well as the 2 Remote Operated Circuit Breakers (ROCB) mains breakers. (Refer to the
Solid State Breaker Ratings table for respective trip currents.) Operators can program
the power up/down sequence and power up/down delays for each channel, along
with the low voltage disconnect (LVD) and over voltage disconnect (OVD) thresholds.
The PDU monitors line voltage, circuit breaker status and internal temperature
to provide the required power and circuit protection to connected equipment.
Operational control is performed either manually by front panel push buttons or
remotely through either an RS-232 serial console port 10/100 BASE-T or LAN TCP/IP
socket or telnet session.
There are numerous ROCB values available that provide primary current protection
to the PDU and down stream equipment powered by the PDU. The ROCBs are UL
listed primary circuit protection for the six outputs on side A and B. The high current,
direct feed version provides easy power cycling to -48 VDC powered routers/switches,
DSLAMS and other enterprise-related equipment via remote activated circuit
breakers rated up to 100 Amps.
The DC SMARTStart® and power monitoring set have been employed together or
individually in various applications in many industries.
16
Features
-48 VDC or +24/+28 VDC input
power; voltage configurable for
International use
User defined power up sequence
order and delay & current limiting.
Fully programmable sequence &
delay on a per channel basis
Solid state electronic circuit breaker
technology; Auto reset to nuisance
trip breakers - user configurable
Monitors line voltage. circuit
breaker status, and internal
temperature of the PDU, LVD & OVD
On board 6 month event log
LAN TCP/IP socket, Telnet
connection or RS-232 serial console
port remote control capability
SNMP agent on board
Flash upgradable in the field
Front Panel push buttons for
local output control. Output status
is displayed through individual
tri-colored LEDs for each output.
EMI filtering to protect against noise
and interference
Independent programmable
power on and off sequencing
delays to reduce/manage the
level of inrush current transients
Technical Specifications
Distributed Output P/N
Specifications
7832S30
Input Voltage VDC
7832S3024
7832S60
Direct A and B P/N
7832S6024
7832RB050
7832RB080
7832RB100
-48
+24
-48
+24
-48
-48
-48
Input Current
30 Amps
30 Amps
60 Amps
60 Amps
50 Amps
80 Amps
100Amps
Individual Output
Steady State Load Max
5 Amps
5 Amps
10 Amps
10 Amps
50 Amps
80 Amps
100Amps
Factory Set Trip Current
Nominal
5.9 Amps
5.9 Amps
11.2 Amps
11.2 Amps
60 Amps
100 Amps
120Amps
Input Connection
Non-rotational terminal block 5/8” centers, 1/4-20 threads
Output Config.
6 A, 6B
6 A, 6B
6 A, 6B
Non-rotational terminal block 5/8” centers,
1/4-20 threads
6 A, 6B
1 A, 1B
1 A, 1B
1 A, 1B
Electrical and Mechanical Specifications
Input Voltage
-48, or +24 VDC
Size (Overall)
17.25”W x 1.75”H x 8.00”D (43.8cm W x 4.44cm H x 20.4cm D)
Weight
13.3 lbs. (6.1 kg)
Operating Temp.
0 - 45°C (32 - 113°F)
Operating Humidity
0 - 95% (non-condensing)
Operating Elevation
0 - 10,000 ft. (0 - 3000 m)
Solid State Breaker Rating
Trip Curve
Steady State Amps
Factory Set Trip Current
Slow
(51-110 msec)
Medium
(11-50 msec)
Fast
(<10 msec)
3
3.45



5
5.75



7.5
8.625



10
11.5



15
17.25



20
23
N/A
N/A

Military Applications
•
•
•
•
Unmanned Vehicles
Command Post Platforms
Simulators
Competitive Local Exchange Carriers
(CLECs)
• Incumbent Local Exchange Carriers
(ILECs)
Commercial Applications
• XDSL applications, CATV enterprises
• blade servers
• Power several devices including
blades, servers, switches,
communications equipment
UL listed and NEBS
Level 3 certified.
Complies to FCC and
CE requirements.
Rev: 09/17/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
17
www.apitech.com
Night Vision Test Set
Using the Night Vision Test Set, military personnel can determine the resolution
performance of night vision devices. This small, portable test set can be operated
in the field for a quick “go/no go” analysis of night vision devices to support mission
safety and success.
The test set evaluates the performance of Gen II and Gen III devices providing a near
infrared uniformly illuminated target as well as two toggle switches to select high and
low light level conditions.
Features
Subject to export control under
the jurisdiction of the International
Traffic in Arms Regulations (ITAR).
Unauthorized exportation is
prohibited.
Tests all US Military standard night
vision devices
Night Vision Test Set Includes:
• Test set unit with goggle adapter and
lens cap
Uses commercially available 9V
batteries
- AN/PVS-5A, B and C
- AN/PVS-7A, B and C
- AN/PVS-14
- AN/PVS-6(V)1, 2 and 3
Compact and lightweight;
- AN/PVS-9 (F4949), all
models, and (F5050)
• Weapon sight adapter for
AN/PVS-4 and AN/TVS-5
Built in Calibration Sensor
• Driver’s viewer adapter for
AN/VVS-2, V1, V2, V3
• Lens Tissue
Applications
• Carrying bag
• Goggles
• Weapon sights
• Drivers’ viewers
• Shipping/storage case
18
Hawk-iTM
Video Aiming Device for Explosive Ordnance Disposal (EOD) Robots
Take the guesswork out of aiming your PAN™ disrupters. The Hawk-i™ Video Aiming
Device utilizes a camera and a rangefinder to automatically place crosshairs on your
monitor. As you approach a target the crosshairs shift based on your range to the
target to show operators the true point of impact for their shot. No calibration is
required and no adjustments are needed by the operator to account for the range
to the target. The system also displays range to target in the upper left corner of the
video image.
This camera sighting system is designed to work from a robot and will mount onto
the barrel of the disrupter. Versions are available for several popular EOD robots, and
the system can be configured for other robotic platforms, contact sales.
The camera projects crosshairs on the target and they are seen on the robot’s
monitor. This way you can mount the camera to one barrel and be able to see the
crosshairs for each barrel. The Hawk-i rangefinder will measure the distance from
the end of the barrel to the target that will display in the upper left corner of your
monitor. The rangefinder is good up to 48 inches.
The camera can project two sets of crosshairs if you have a dual mount. The crosshairs
are overlaid on the video image and then sent back to the robot control station
through the robot’s accessories port or weapons port. While approaching a target, the
crosshairs shift based on your range to the target to show operators the true point of
impact for their shot. It takes less than 5 minutes to integrate the aiming system to
the robotic platform.
Tilt (Angle of Fire): An additional capability to the Hawk-i video sighting system
that can be enabled as an option at the factory.¹ The Hawk-i can display the tilt
angle of the disrupter barrel. This is an additional piece of data often desired by EOD
technicians to ensure that the disrupter shot is taken at the ideal angle to produce
the optimal result. The tilt readout, when enabled, will be displayed underneath the
range reading on the video screen. The angle is given in degrees.
20
Features
Crosshairs are projected on to
operator’s video monitor and are
automatically updated based on
range to target; Provides
crosshairs for dual barrels
through one system3
Range to target is displayed
on operator’s video monitor;
Requires access to one analog
video channel on a robotic
platform
Sealed enclosure for environment
and shock resistance; 5-minute
integration; No external monitor
or hardware required at the
robot’s base station
Minimum Standoff Distance:
9 inches2; Maximum Standoff
Distance: 48 inches2; No
calibration required
2011 Edison Gold Award for
Best New Product!
Configuration and Delivery Details:
•
•
•
•
•
Standard mounting offset for Hawk-i™ from end of barrel is 0.75”; custom offset must be stated at time of order.3
Hawk-i™ and Cobra Sight™ aiming systems are not ITAR-restricted.
Hawk-i™ versions are available for ANDROS F6A, tEODor, and TALON; contact us about Telemax support.
Hawk-i™ for F6A is compatible with ANDROS F5, F6A, F6B, HD-1, HD-1J.
Hawk-i™ is compatible with 12-gauge PAN™ disrupter; contact us about support for Benelli Super 90.
The Hawk-i™ Video Aiming Device can also be utilized in conjunction with the Cobra Sight™ Laser Aiming Device.
Notes:
1. Rev 2 systems and later
2. Measured from face of video module
3. Requires programming for given barrel configuration at factory
System P/N(s)
B00272-D00
Description
Hawki for
Teodor (PAL)
Component P/N
B00273-D00
Hawki for
F6A
CEU
1.2
5.5 x 3.25 x 1.75
Video Module
CEU Cable
Video Cable
0.6
0.2
0.2
3.25 x 2.25 x 1.75
18 long
28 long
23-6416-0141
Mounting bracket
0.3
5.48 x 3.00 x 0.25
B00659-D02
Hardware Kit
0.1
6-32 3/16" Phillips screws (CEU to mounting plate)
two (2) x 8-32 3/16” set screws (video module to barrel)
0.2
17 pages 8.5 x 11
2.8
17.5 x 12.5 x 4.5
Install/Operation
Manual
Carry Case
Total Weight of
System:
5.6
B00006-D00
CEU
1.2
5.5 x 3.25 x 1.75
B00004-D03
72-1031-24086
72-1031-26008
23-6416-0141
Video Module
CEU Cable
Video Cable
Mounting bracket
0.6
0.2
0.2
0.3
B00659-D02
Hardware Kit
0.1
3.25 x 2.25 x 1.75
18 long
28 long
5.48 x 3.00 x 0.25
6-32 3/16" Phillips screws (CEU to mounting plate)
two (2) x 8-32 3/16” set screws (video module to barrel)
5/64" short-arm hex L-key 2" long (for set screws)
B00272-D00_IOM
Install/Operation
Manual
0.2
17 pages 8.5 x 11 (same as B00272-D00)
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
B00006-D00
B00004-D00
72-1031-24085
72-1031-26008
Total Weight of
System:
CEU
Video Module
CEU Cable
Video Cable
B00276-A00
Mounting bracket
B00659-D00
B00273-D00_IOM
B00274-D00
+1 888.588.3448
powersales@apitech.com
Dimensions (inches)
B00006-D00
B00274-D00
Hawki for
Teodor
(NTSC)
Weight
(lbs)
B00004-D02
72-1031-24086
72-1031-26008
B00272-D00_IOM
B00272-D01
Component
Description
5.6
Hardware Kit
Install/Operation
Manual
Carry Case
Total Weight of
System:
21
1.2
0.6
0.2
0.2
5.5 x 3.25 x 1.75
3.25 x 2.25 x 1.75
18 long
28 long
0.4
5.48 x 3.00 x 0.25
0.1
four (4) x 10-32 3/8" Phillips screws (CEU to mounting
plate)
two (2) x 10-24 1/2" Phillips screws (mounting plate to
robot)
two (2) x 8-32 1/2" Phillips screws (mounting plate to
robot)
0.2
16 pages 8.5 x 11
2.8
17.5 x 12.5 x 4.5
5.7
System P/N(s)
B00273-D01
Description
Hawki for
AFMSR
Component P/N
B00797-D00
B01039-D00
Hawki for
Telemax
+1 888.588.3448
powersales@apitech.com
Weight
(lbs)
Dimensions (inches)
B00006-D00
CEU
1.2
5.5 x 3.25 x 1.75
B00004-D00
Video Module
0.6
3.25 x 2.25 x 1.75
72-1031-24085
CEU Cable
0.2
18 long
72-1031-26008
Video Cable
0.2
28 long
B00276-A00
Mounting bracket
0.4
5.48 x 3.00 x 0.25
B00659-D00
Hardware Kit
0.1
(4) x 10-32 3/8" Phillips screws (CEU to mounting plate)
(2) x 10-24 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 3/16” set screws (video module to barrel)
5/64” short-arm hex L-key 2” long (for set screws)
B00273-D00_IOM
Install/Operation
Manual
0.2
16 pages 8.5 x 11 (same as B00273-D00)
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
5.7
CEU
1.2
B00006-D00
Hawki for
TALON
Component
Description
5.5 x 3.25 x 1.75
B00004-D00
Video Module
0.6
3.25 x 2.25 x 1.75
72-1031-00101
CEU Cable
0.2
24 long
72-1031-26008
Video Cable
0.2
28 long
B00276-A00
Mounting bracket
0.4
5.48 x 3.00 x 0.25 (see Note 1 below)
B00659-D00
Hardware Kit
0.1
(4) x 10-32 3/8" Phillips screws (CEU to mounting plate)
(2) x 10-24 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 3/16” set screws (video module to barrel)
5/64” short-arm hex L-key 2” long (for set screws)
B00797-D00_IOM
Install/Operation
Manual
0.2
16 pages 8.5 x 11
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
5.7
B00006-D00
CEU
1.2
5.5 x 3.25 x 1.75
B00004-D02
Video Module
0.6
3.25 x 2.25 x 1.75
72-1031-24087
CEU Cable
0.2
18 long
72-1031-26008
Video Cable
0.2
28 long
B00276-A00
Mounting bracket
0.4
5.48 x 3.00 x 0.25
B00659-D00
Hardware Kit
0.1
(4) x 10-32 3/8" Phillips screws (CEU to mounting plate)
(2) x 10-24 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 1/2” Phillips screws (mounting plate to robot)
(2) x 8-32 3/16” set screws (video module to barrel)
5/64” short-arm hex L-key 2” long (for set screws)
B01039-D00_IOM
Install/Operation
Manual
0.2
15 pages 8.5 x 11
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
5.7
22
Hawk-i™ Benefits:
• The automatic crosshairs created by the Hawk-i™ video
aiming system enables faster action, as less guesswork
is involved in creating a target shot
• Compatible with all 12-gauge PAN™ Disrupters
• Significant improvement over venetian blind
• Increased effectiveness is also guaranteed, as less time will
need to be spent on aiming
• When used in union with the Cobra Sight™ Laser Aiming
Device, the effectiveness and accuracy of
aiming at targets increases
• The aiming system also decreases the chances of human
error causing misfiring
Cobra Sight™ Laser Aiming Device:
The Cobra Sight™ Laser aiming device is an inventive new tactical device which utilizes true
boresight technology. With this aiming device the end of the barrel remains uncovered,
making zeroing in much faster. Two line lasers are utilized to project a true crosshair on your
target for ranges greater than 7 inches without adjustment. With the Cobra Sight™ Laser, a
more precise shot is guaranteed.
To learn more about API Technologies Power Solutions, including the Hawk-i™ Video
Aiming Device or Cobra Sight™ Laser Aiming Device, please contact +1 (888) 588-3448
or email powersales@apitech.com
Rev: 08/26/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
23
www.apitech.com
Cobra Sight™
Laser Aiming Device for Explosive Ordnance Disposal (EOD) Robots
The Cobra Sight™ Laser Aiming Device is an inventive new tactical device which
utilizes true boresight technology. With this aiming device, the end of the barrel
remains uncovered, making zeroing in both fast and simple. Two line lasers project a
true crosshair on the target for ranges greater than 7 inches without adjustment. The
Cobra Sight™ Laser aiming system enables people to act quicker, as the aiming device
makes zeroing in faster. With a more accurate aim, less misfires and mistakes will
occur because of shot placement issues and more precise shot is guaranteed.
Cobra Sight™ Key Benefits
• Compatible with all 12-gauge
PAN™ Disrupters
• No removal required before a shot
is taken
• Minimum Standoff Distance: 7 inches
• PAN™ Stand Version: 2 AA Batteries
• Robot-Mount Version: 12 V/200mA
• Class 3R Device (two class 3A lasers)
• Factory-calibrated, but also
user-adjustable
• True boresight technology
Features
Two line lasers intersect to
produce a true crosshair
Sealed enclosure for
environmental and
shock resistance;
ON / OFF controlled by robot’s
own laser switch or by external
switch (PAN Stand Version).
Factory-calibrated, but also useradjustable
The Cobra Sight™ Laser Aiming Device can also be used in conjunction with the
Hawk-iTM Video Aiming Device.
Hawk-i™ Video Aiming Device
The Hawk-i™ Video Aiming Device utilizes a camera and a
rangefinder to automatically place crosshairs on your monitor.
While approaching a target, the crosshairs shift based on your
range to the target to show operators the true point of impact for
their shot. No calibration is required and no adjustments are needed
by the operator to account for the range to the target. The system also
displays range to target in the upper left corner of the video image. The Hawk-i™
Video Aiming Device promotes a more accurate shot.
24
To learn more about the API Technologies’
Power & Systems Solutions, including
Explosive Ordnance Disposal (EOD) Robotic
Subsystems, the Hawk-i™ Video Aiming
Device or Cobra Sight™ Laser Aiming Device,
please contact +1 (888) 588-3448 or email
powersales@apitech.com
System P/N(s)
Description
Component P/N
B01055-D00
B00279-D00
Cobra Sight
for Teodor
Cobra Sight
for PANstand
Dimensions (inches)
CEU
1.2
5.5 x 3.25 x 1.75
B00005-D00
Laser Module
0.4
3.25 x 2.25 x 1.75, attached cable 18
long (includes all set screws)
CEU Cable
0.2
18 long
Mounting bracket
0.4
5.48 x 3.00 x 0.25
B00276-A00
Cobra Sight
for F6A
Weight (lbs)
B00006-D00
72-1031-24085
B00895-D00
Component
Description
B00659-D03
Hardware Kit
0.1
four (4) x 10-32 3/8" Phillips screws
(CEU to mounting plate)
two (2) x 10-24 1/2” Phillips screws
(mounting plate to robot)
two (2) x 8-32 1/2” Phillips screws
(mounting plate to robot)\
5/64” short-arm hex L-key 2” long
(for set screws)
B00895-D00_
IOM
Install/Operation
Manual
0.2
13 pages 8.5 x 11
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
5.3
B00006-D00
CEU
1.2
5.5 x 3.25 x 1.75
B00005-D00
Laser Module
0.4
3.25 x 2.25 x 1.75, attached cable 18
long (includes all set screws)
72-1031-24086
CEU Cable
0.2
18 long
23-6416-0141
Mounting bracket
0.3
5.48 x 3.00 x 0.25
B00659-D04
Hardware Kit
0.1
6-32 3/16" Phillips screws (CEU to
mounting plate)
5/64” short-arm hex L-key 2” long
(for set screws)
B01055-D00_
IOM
Install/Operation
Manual
0.2
13 pages 8.5 x 11
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
5.2
B00081-D00
Battery Box w/
Mounting Plate
0.9
5.13 x 2.82 x 2.75 (includes 2 x AA
batteries)
B00005-D00
Laser Module
0.4
3.25 x 2.25 x 1.75, attached cable 18
long (includes all set screws)
B00276-A00
Mounting bracket
0.4
5.48 x 3.00 x 0.25
B00279-D00_
IOM
Install/Operation
Manual
0.2
10 pages 8.5 x 11
B00274-D00
Carry Case
2.8
17.5 x 12.5 x 4.5
Total Weight of
System:
4.7
Rev: 09/18/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
25
www.apitech.com
Box Builds and Build to Print
Technology Capabilities
API Technologies is a fully integrated “one-stop shop” for engineering, design, and
manufacturing of solutions. With our breadth of expertise, established business
partners, and design-formanufacturing capabilities, we are ready to dedicate
ourselves to understanding your needs with the end result of moving your project
forward seamlessly.
Our team can support all box builds, build-to-print, and turn-key solutions. We will
collaborate from the early stages of development, provide prototyping capabilities,
and ensure quality through testing with the end goal of volume production.
Product Verification: quality and reliability is our commitment to our customer
• Products are tested for electrical, mechanical, and environmental metrics.
• In order to provide the most accurate and specific testing procedures, our team
uses custom and automated test equipment that is used at critical points in our
manufacturing operation.
• We administer our test procedures not only for prototypes, but for each and every
power product we manufacture.
• Dependent on application, our team can tailor additional tests to provide verification
for unique application environments.
Technology Capabilities
API employs a diversified array of state-of-the-art equipment for applications in
research & development prototypes, test, measurement, and simulation of electrical
components & systems using our in-house design tools. Our team models and
accurately defines the best design and package solution. API Technologies prides
itself in having the capability to handle a one of a kind prototype unit as well as
moderate volume assembly and test. We also run production lines utilizing custom
designed automated test stations for specific applications, geared to provide
optimum cost and manufacturing efficiencies.
• Large Scale Production Systems
• Development, Integration, Staging,
Testing, Installation, and Maintenance
Training
• High Temperature at Full Load
• Low Temperature at Full Load
• DC Resistance
• Short Circuit Test
• Thermal cycling
• Humidity Resistance
• Salt Spray
• High Temperature Burn-In
• ATE for Electrical Verification
• Laser Welding
• Screen Printing
• Pick and Place
• CNC Machining
• Thermal Imaging
• Schematic Capture
• Allegro PCB Design
• Solidworks Modeling
Rev: 08/26/14
+1 888.588.3448
powersales@apitech.com
power.apitech.com
26
www.apitech.com
COTS & MOTS & Custom Solutions
Commercial-Off-The-Shelf, Modified/Military-Off-The-Shelf, and Custom Power Distribution
API Technologies understands that not every need can be met with our standard
product offering. If you cannot find a standard solution that matches your exact
needs, we are more than happy to tailor a unique solution for your application.
Whether you need a slight modification to an existing design or a completely
customized solution, we are pleased to provide our vast array of engineering skills to
design and develop your desired solution.
Custom design collaboration is a hassle-free experience for API customers. Clients
work directly with our design team, eliminating any 3rd party companies, which
helps reduce design time. Our design team has a proven track record for developing
complex solutions within limited time frames.
Advanced technology is employed for a comprehensive system review of packaging
preparation and manufacturability. All products are tested for agreed upon electrical,
mechanical, and environmental metrics. We administer our test procedures not only
for prototypes, but for each and every power product we manufacture. This focus on
quality and reliability is part of the commitment we make to our customers.
Rugged Features:
• Rugged Designs
• MIL-STD-810
• MIL-STD-461E
• MIL-STD-1275D
• MIL-STD-1686C
• Wide Operating Temperature Range
(-46°C to 60°C)
• Quality Testing for Unique Environments
Defense Capabilities
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
+1 888.588.3448
powersales@apitech.com
power.apitech.com
27
AC & DC Capabilities
Single Phase AC
Three Phase AC
-48, +12, or +24/+28 VDC
0U, 1U, or 2U Rack Mount Designs
Non-Rack Mount Designs
Variety of Receptacles and Plugs
Circuit Protection with UL-Listed
Circuit Breakers
Audible Alarm
Local Power Meter
Remote Capture of Power Draw &
Temperature
Remote Cycling & Sequencing of
Device Loads
Automatic Transfer Switch (ATS)
UL Listed/CE Mark
Surge Suppression
Emergency Power Off (EPO)
Elapsed Time Indicator
EMI Filtering
Transient Voltage Suppression
Voltage Ride Through
EMP Protection
Customer Private Label
Internal R&D
In-house Design Team
Company Owned Manufacturing
Facilities
Reverse Engineering Capabilities
Full Vertical Integration
www.apitech.com
Rev: 08/26/14
Notes
Notes
API Technologies Corp. (NASDAQ: ATNY) is a leading technology provider
of RF/microwave, microelectronics, and security technologies for critical and
high-reliability applications, including aerospace, defense, industrial, medical,
energy, and communications. The company’s international customers include
leading Fortune 500 firms, as well as the governments of the U.S., Canada,
the United Kingdom, NATO and the European Union.
RF/Microwave & Microelectronics
A leader in high-performance RF/microwave & microelectronic solutions, the company
designs, develops and manufactures one of the world’s largest selections of RF, microwave
and millimeter wave components and systems for use in commercial, defense, and space
applications. The company offers both US and Europe-based design and manufacturing
options.
Featured Products: Integrated Microwave Assemblies (IMAs), RF Components, Microwave
Filters, Frequency Sources, Amplifiers, Low Cost High Volume SMT Amplifiers, Thin Film,
and RF Build-to-Print, Microelectronics, 1553 Data Bus, Custom Hybrids , Solid State Power
Control, Hybrid-related Manufacturing, Advanced Ceramics, Thin Film
Electromagnetic Integrated Solutions
Trusted components to aid EMC compliance, power storage for high voltage inverters, energy
efficiency and power management, including the world’s largest selection of EMI filtering
components, and EMC Compliance Lab.
Featured Products: Coaxial Filters & Interconnects, Power Filters & Film Capacitors for High
Voltage Apps, Magnetics, Specialty Connectors & Cabling
Secure Systems & Information Assurance
Security products and solutions, which address emerging cyber security threats for
government, defense and the enterprise. In situations where compromised data could have
financial, political and/or life-threatening consequences, information assurance is the highest
priority. API offers a variety of security solutions for these sensitive environments.
Featured Products: Encryption Solutions, Secure Applications, Information Assurance,
TEMPEST & Emanation Security
Power Solutions
Leading supplier of AC and DC power distribution for military, commercial, and industrial
applications. Experienced engineering and design team specialize in military, custom power
distribution, box builds, COTS (Commercial off-the-shelf), and OEM/ODM services.
Featured Products: Rack Mount & Non-Rack Power Distribution Units & Power Strips,
Three Phase PDUs, Monitored & Sequenced PDUs, Power Supplies, MIL-STD Power Panels
Electronics Manufacturing Services (EMS)
Manufacturing and prototyping services provided to defense, industrial & commercial OEM’s.
Featured Products: Component Selection Optimization, New Product Introduction (NPI)
& Rapid Prototyping, Electronics Manufacturing, Substrate Manufacturing, Mechanical
Production, Design Engineering (DfM), Integration, Testing & Programming of Hardware
Learn more at www.apitech.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising