"Aktor M" Electromotive actuators

"Aktor M" Electromotive actuators
“Aktor M”
Electromotive actuators
Technical information
Tender specification:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control
(0-10 V), with squeeze connection and position feedback signal
0-10 V.
Models:
Item no.:
24 V, steady control with 0-10 V
or switching as two or three point control.
Type of characteristic line
(linear, equal percentage) adjustable.
With enclosed adapter for Oventrop valves.
1158010
Same actuator as item no. 1158010
but without enclosed adapter
1158011
24 V ~/=
4.9 W during operation
8.7 W in final lift position
0 - 10 V
10 mm
500 N
7.5 / 15 s / mm
IP 54 according to EN 60529
120 °C
-10 °C up to +55 °C
-10 °C up to +55 °C
5 x 0.5 mm²
157
Operating current:
Power consumption:
Drive:
Max. piston stroke:
Operating power:
Floating time:
Protection:
Max. fluid temperature:
Ambient temperature:
Storage temperature:
Connecting cable:
63
43.5
Actuator
Technical data:
Adapter
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
122
35
126.5
Dimensions with mounted adapter
Variant
(3pt)
Variante 11 (3pt)
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
24 V~/=
open/stop/close
Depending on the wiring (see connection diagrams), the actuators
item no. 1158010/11 can be used as two point, three point or
0-10 V actuator.
BN BK
RD GY
MM 01 02
BU
03 05
Application:
The actuators can be combined with the following Oventrop
valves:
Variant
2 (2pt)
(2pt)
Variante 2
24 V~/=
open / close
Item no. 1158010:
“Cocon QTR/QFC” DN 40 and DN 50
Item no. 1158011:
Two-way valves item no. 11308.. and 16708 DN 15-DN 50
BU
Function:
BN BK
RD GY
MM 01 02
03 05
Variant 3 (0-10 V)
Variante 3 (0-10 V)
–Synchronous motor with activation and switch off technology
24 V~/=
y=0...10 V
–Maintenance-free gear with magnetic coupling
–Gear release for manual positioning of the valve. To do so,
activate the lateral sliding switch and set the actuator to the
required position with the help of the enclosed key.
y0=0...10 V
–Electronic recognition of the limit of travel via timer
BU
BN
BK
MM
01
02
RD
GY
03
05
A/D
P
M
Connection diagrams item no.1158010/11
2017 Oventrop
1
“Aktor M”
Electromotive actuators
Tender specification:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control, with
squeeze connection and position feedback signal 0-10 V.
1158020:
0(2)..10 V=
1158021/22:
0(2)..10 V= or 0(4)..20 mA
With enclosed adapter for Oventrop valves.
Models:
Item no.:
24 V, steady control with 0(2)-10 V
or switching as three point control.
Linear characteristic line.
1158020
24 V, steady control with 0(2)-10 V or 0(4)-20 mA
or switching as two or three point control.
Linear characteristic line.
With spring return.
Valves opening with current “off”.
1158021
24 V, steady control with 0(2)-10 V or 0(4)-20 mA
or switching as two or three point control.
Linear characteristic line.
With spring return.
Valves closing with current “off”.
1158022
Item no. 1158020 and adapter
Technical data:
Item no. 1158020:
Operating current:
Power consumption:
Drive:
Max. piston stroke:
Operating power:
Floating time:
Protection:
Max. fluid temperature:
Ambient temperature:
Storage temperature:
Actuator:
24 V ~; 50/60 Hz
4.8 W during operation and in
final lift position
0 (2)– 10 V
20 mm
800 N
9 s / mm
IP 54 according to EN 60529
120 °C
0 up to 50 °C
0 up to 50 °C
reversible synchronous motor
Item no. 1158021/22 and adapter
Item no. 1158021/22:
Operating current:
Power consumption:
Drive:
Max. piston stroke:
Operating power:
Floating time:
Emergency setting time:
Protection:
Max. fluid temperature:
Ambient temperature:
Storage temperature:
Actuator:
24 V ~; 50/60 Hz
26 W during operation and in
final lift position
0(2) – 10 V or 0(4) – 20 mA
20 mm
1000 N
2 s / mm
1 s / mm
IP 54 according to EN 60529
120 °C
0 up to 50 °C
0 up to 50 °C
brushless direct current motor
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
Depending on the wiring (see connection diagrams), the actuators
item no. 1158020/21/22 can be used as two point, three point or
0(2) -10V or 0(4) - 20 mA actuator.
Dimensions of actuators and connections sizes of adapter
2
2017 Oventrop
„Aktor M“
Elektromotorische Stellantriebe
Application:
The actuators can be combined with the following Oventrop
valves:
(steady)
“Cocon QTR/QFC“ DN 40 up to DN 100
Function:
–electronic switching operation depending on the motive force
–compensation of external interferences by dynamic hysteresis
–linear characteristic line
–valve blocking function, short stroke lift if the actuator has not
moved within 24 h (optionally adjustable)
–automatic piston stroke adaptation by initialization
–manual setting of item numbers 1158021/22 by removing the
cover and by setting the actuator to the required position with
the help of a 4 mm Allen key
–maintenance-free
(2pt)
LED display:
Item no. 1158020:
Permanent light:
Slow flashing:
Irregular fast flashing:
Off:
Item no. 1158021/22:
Permanent light:
Short flashing:
Long flashing:
Normal operation
Initialization run or partial initialization
after power failure
Valve is blocked or manual setting
Power supply interrupted or actuator
fuse defective
Normal operation
Malfunction / reverse polarity
Initialization run
(3pt)
Priority for 2pt & 3pt: “Drive stem closing down“
Connection diagrams item no. 1158020
(steady)
(2pt)
24 V AC
OV AC/DC
1
3
1 = On
2 = Stop
3 = Closed
(3pt)
24 V AC
OV AC/DC
1 2 3
Connection diagrams item no. 1158021/22
2017 Oventrop
3
“Aktor M”
Electromotive actuators
Tender specification:
Oventrop electromotive actuators for steady control. The actuator
can be used for two point, three point or proportional control
(0-10 V or 4-20 mA), with squeeze connection and position feedback signal 0-10 V.
With enclosed adapter for Oventrop valves.
Models:
Item no.:
24 V, steady control with 0-10 V or 4-20 mA
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
1158030
24 V, steady control with 0-10 V or 4-20 mA
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
With spring return.
Valves opening with current “off”
1158031
24 V, steady control with 0-10 V or 4-20 mA
or switching as to or three point control.
Type of characteristic line (linear, square-law,
equal percentage) adjustable.
With spring return.
Valves closing with current “off”
1158032
Actuator and adapter
230
60
57
18.5
Item no. 1158031/32:
Operating current:
Power consumption:
Drive:
Max. piston stroke:
Operating power:
Floating time:
Protection:
Max. fluid temperature:
Ambient temperature:
Storage temperature:
Number of spring returns:
Ø 44
90
24 V ~/=
10 W during operation
20 W in final lift position
0-10 V or 4-20 mA
40 mm
2000 N
2 / 4 / 6 s / mm
IP 66 according to EN 60529
120 °C
-10 °C up to +55 °C
-10 °C up to +55 °C
> 4000
64
30
Drive:
Max. piston stroke:
Operating power:
Floating time:
Protection:
Max. fluid temperature:
Ambient temperature:
Storage temperature:
24 V ~/=
10 W during operation
18 W in final lift position
0-10 V or 4-20 mA
40 mm
2500 N
2 / 4 / 6 s / mm
IP 66 according to EN 60529
120 °C
-10 °C up to +55 °C
-10 °C up to +55 °C
289
Operating current:
Power consumption:
136
Technical data:
Item no. 1158030:
Dimensions of actuators and connection sizes of adapter
Installation:
The connecting cable must not come into contact with the hot pipe
as excessive heat will accelerate the ageing of the cable insulation.
Electrical connection must be carried out in accordance with the
requirements of the local Electricity Board.
The Oventrop electromotive actuators can be installed in any
position, except for vertical downward position.
Depending on the wiring (see connection diagrams), the actuators
item no. 1158030/31/32 can be used as two point, three point or
0-10 V or 4-20 mA actuator.
4
2017 Oventrop
“Aktor M”
Electromotive actuators
Application:
The actuators can be combined with the following Oventrop
valves:
2pt
3pt
24V~/=
24V~/=
“Cocon QFC” DN 125 up to DN 200
Two-way valves item no. 11308.. and 16708.. DN 65 up to DN 150
1 2a 2b 3u3i 44
Function:
1 2a 2b 3u3i 44
–electronic switching operation depending on the motive force
–automatic recognition of the input control signal
–setting of the characteristic line at the actuator (linear, squarelaw, equal percentage)
Steady
24V~/=
–automatic adaptation
y = 0…10V
–free choice of mode of operation
1 2a 2b 3u
3i
y = 4…20mA
44
y0 = 0…10V
–choice of characteristic line
–setting of floating time via coding switch
–the actuator can be set manually with the crank handle
–reinitialization is triggered with the crank handle
S1 S2 S3 S4
LED display:
Both LEDs flash red:
One LED glows green: Idle position, last direction of travel
according to LED
Off:
Final position, valve position according
to LED
Connection module 230 V
1158033
For the connection of the 24 V actuators “Aktor M”, item no.
1158030/31/32 to the 230 V supply voltage.
Module for plug-in connection to the actuator.
3i
44
4mA
OV
100% 10V 20mA 10V
0% 10V 20mA OV
2b
100% OV 4mA 10V
Stem
0%
100%
Connection diagrams item no. 1158030
2pt
3pt
24V~/=
No power supply or no activation in
three point mode
Accessories:
3u
OV
S1, S2 = Floating time
S3, S4 = Type of characteristic line
One LED flashes green:A piston stroke is carried out by the
actuator, direction according to LED
One LED glows red:
2a
On
Off
Initialization
0%
24V~/=
21 1 2a 2b 3u3i 44
21 1 2a 2b 3u3i 44
Steady
24V~/=
y = 0…10V
21 1 2a 2b 3u
S1 S2 S3 S4
2a
On
Off
2b
0%
3i
y = 4…20mA
3u
3i
44
OV
4mA
OV
y0 = 0…10V
100% 10V 20mA 10V
0% 10V 20mA OV
100% OV 4mA 10V
S1, S2 = Floating time
S3, S4 = Type of characteristic line 1158031 1158032
21
44
Stem
0%
100%
100%
0%
2pt, 3pt, steady
Connection diagrams item no. 1158031/32
Subject to technical modifications without notice.
Product range 3
ti 315-EN/10/MW
Edition 2017
2017 Oventrop
Gedruckt auf chlorfrei
gebleichtem Papier.
5
3.38
2017 Oventrop
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising