User Manual - Dolphin Solutions

User Manual - Dolphin Solutions
BC 230C Dolphin Chrome Plated Hand Dryer
User Manual
Please read carefully before use
Thank you for purchasing the BC 230C Dolphin Hand Dryer.
This hand dryer is controlled by CPU, and adopts an infrared sensor. The all-metal cover and double
protection against overheating ensure that the automatic hand dryer is durable, safe and ergonomic.
With 30m/s air speed and 270m3/h air volume it dries hands quicker than other hand dryers.
Adjustable air nozzle as 360°, makes it could be used to dry your hair and body. It is an ideal choice
for hotel, office, washroom, etc.
l Durable all-metal cover
l High air volume
l Reliable with high power motor gives fast air speed for quicker drying time
l Adjustable air nozzle swivels through 360°,to dry hair, face or hands.
1. Screw
2. Cover
3. Sensor (No.IV :manual button)
4. Air nozzle
Recommended installation height(measured from air outlet to the floor):for man 1.2m,for woman 1.1m,
for child 0.9m.
Electrical connection must be made to the fixed wiring of the property using a double pole isolating
switch, with a break contact distance of at least 3mm.
This product must be earthed.
BC 230 User Manual
Remove the cover in order of ĺĹĸķ as shown in (Figure3); Do not overexert while removing the
cover to prevent from breaking the wire between the cover and the base;
Drill 4 holes of 8mm diameter, 35mm deep; (Figure1)
Fix the base to the holes by using the plugs and the screws attached; (Figure2)
Fix the hand dryer as shown in (Figure3), ķ Connect the ground wire to the cover; ĸ Connect the lead
wires of sensor in the cover and base; as shown in Ĺˈhang the cover at the top of the base; lastly, press
the cover to the base, and use the Allen key attached to screw down the screws as shown in ĺ.
Switch on the power, the hand dryer will work automatically when hands placed.
Concealed wire installation: remove the original power cord, lead the prepared wire into the hand dryer
through the base hole, and connect the wire to the wiring terminal N, L and
After finish the installation, switch on the power, and the hand dryer will work automatically when
place hands underneath the air outlet.
The hand dryer blows the hot air when hands are 11cm or closer to the air outlet, and it stops working 1
second after removing hands. It will also stop working automatically after 1 minute consecutive use. To
restart the hand dryer, put hands back underneath and re-operate the sensor.
For No.IV, press the button, it blows hot air that lasts for 30±5 seconds, and stops automatically.
Repress to restart working.
In order to meet different circumstances, the induction sensibility of the hand dryer is set at the highest
point. If it works for overlong or does not work after installation, please adjust the sensor.
The hand dryer must be installed away from the place for shower bath;
Do not install the product near the bathtub, washbowl or other vessels that contain water;
Avoid spattering the product with water;
Do not cover the air inlet and outlet;
Do not shake the hand dryer;
When the hand dryer is out of order during use, please cut off the power immediately, stop using it, and
contact our company or find a qualified electrician to fix it;
7. This product is not intended to use by persons (include children) who are disabled, or lack of
experience and knowledge, unless they are given instruction concerning about the use of the product
and supervised by a person who is responsible for their safety;
8. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a qualified
electrician in order to avoid a hazard.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
This marking indicates that this product should not be disposed with other household wastes
throughout the EU.To prevent possible harm to the environment or human health from uncontrolled
waste disposal,recycle it responsibly to promote the sustainable reuse of material resources.To return
your used device,please use the return and collection systems or contact the retailer where the product
was purchased.They can take this product for environmental safe recycling.
One set of hand dryer
One copy of user manual and one copy of installation template
One pack of screws 4pcs,gexagon wrench 1pc and 嘶8mm plugs 4pcs
Bell-Chem Products Company, Haywood Way, Hastings, TN35 4PL
Tel: 01424 202224 Fax: 01424 205200
BC 230 User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF