ThinAir® HAND DRYER
TECHNICAL DATA SHEET
ThinAir HAND DRYER
®
MODELS: TA - ABS SB
-VOLTAGE (See Chart)
PERFORMANCE
DRY TIME: 14 SECONDS*
ENERGY PER USE: 3.7 Wh*
Wattage: 950 Watts (Heat On) - 300 Watts (Heat Off)
Certifications:
RoHS
CONSTRUCTION
A.All covers will be fastened to a base plate by one chrome plated tamper-proof bolt.
The cover shall be composed of:
ABS – White polymer with SanaForTM antimicrobial additive.
SB – Brushed Stainless Steel.
TA-SB
Brushed Stainless Steel
B.Base plate shall be equipped with (3) 7/8" (22 mm) diameter knockouts, one of which
is located on the right side and suitable for use with surface conduit.
C.All internal parts shall be coated according to Underwriters' Laboratories, Inc.
requirements.
D.Entire mechanism shall be internally grounded, per UL requirements.
TA-ABS
White Polymer
(ABS)
TA-SB
Brushed Stainless
Steel
ADA COMPLIANCE
E.Accessories (optional)
Microban® Antimicrobial Wall Guards:
89W (White), 89B (Black), 89S (Brushed Stainless Steel)
MECHANISM
A.Motor shall be a thermally protected, series commutated, through-flow discharge
vacuum motor/blower (~½ hp / high-30,000 rpm, low-20,000 rpm) which provides
air velocity of up to 16,000 LFM (linear feet per minute) at the air outlet. Includes a
washable metal mesh filter for more reliable performance.
ADA guidelines state that fixtures mounted above 27"
must not protrude more than 4" from the wall.
4"
Maximum: 48"
Recommended: 37"
37"
UL Environment published the first global Product Category Rules (PCR) for
Hand Dryers and Excel Dryer is proud to have been selected to chair the
project. The PCR created evaluation methods through industry consensus that
compare products' environmental impact and performance. Third party testing
results then enable specifiers and buyers to make a true apples-to-apples
comparison of products and more informed decisions.
FOR ARCHITECT/ENGINEER APPROVAL
B.Heating element (550 W) is constructed of Nichrome wire and mounted inside the
blower housing behind air baffle, thereby being vandal resistant. It shall be protected by
an automatic resetting thermostat, which shall open whenever air flow is cut off and
shall close when flow of air is resumed. It shall produce an air temperature of up to
141°F (61°C) at a 72°F (22°C) ambient room temperature at the outlet and 101°F (38°C)
at the hands (4 inches [102 mm] below air outlet).
C. Control assembly is activated by an infrared optical sensor located next to the air outlet.
The dryer shall operate as long as hands are under the air outlet. Control includes a
speed and sound control mechanism, adjustable heat control with High, Medium, Low
and Off settings and a filter sensor which is activated should the filter become clogged.
There is a 35-second lockout feature if hands are not removed. Sensor equipped with
externally visible Red LED light that can flash error codes to assist in troubleshooting.
LIMITED WARRANTY
Job Name
Date
Model Specified
Quantity
The dryer shall be guaranteed to be free from defects for a period of five (5) years.
Warranty shall include labor performed at factory as well as the repair or exchange of
defective parts, at manufacturer's option.
QUANTITY RECOMMENDATIONS
Voltage Specified
One dryer for every two washbasins is sufficient for most applications. If restroom traffic is
unusually heavy, we suggest one dryer per washbasin in small installations and two dryers for
every three washbasins in larger installations. When a 54" washfountain is used, we suggest
four to five dryers.
Customer/Wholesaler
Contractor
Architect
EXCEL DRYER, Inc.
E a s t L o n g m e a d o w, M A Phone 1.800.255.9235
Fax 1.413.525.2853
s a l e s @ e x c e l d r y e r. c o m
w w w . e x c e l d r y e r. c o m
FEB
2017
16TAT0006
TECHNICAL DATA SHEET
ThinAir HAND DRYER
®
MODELS: TA - ABS SB
-VOLTAGE (See Chart)
6 1/2"
(165mm)
8 29/32”
(226mm)
3 1/4"
(82.5mm)
LOCATION OF
SURFACE MOUNT
KNOCKOUT GASKET
WALL
13 15/16”
(354 mm)
13 11/16"
(348mm)
11 13/32"
(290mm)
SURFACE
ELECTRICAL INLET
(1) 7/8” (22mm) DIA.
HOLES
8 25/32"
(223mm)
3 1/4"
(83mm)
ELECTRICAL INLETS
(2) 7/8” (22mm) DIA.
HOLES
3 1/8"
(79.5mm)
4"
(102mm)
1 1/8"
(29mm)
6 1/4"
(159mm)
COVER
BASE PLATE
(Side View)
(Front View)
OVERALL DIMENSIONS
Width: 9 5 ⁄ 32" (233 mm)
Height: 13 15 ⁄16 " (354 mm)
Depth: 4" (102 mm)
WEIGHT
ACTIVATION
MOUNTING
Automatic Sensor Activated
Surface-Mounted
SUGGESTED MOUNTING HEIGHTS
TA-ABS: 8 lbs. (3.6 kgs.)
from floor to bottom of dryer:
TA-SB: 10 lbs. (4.5 kgs.)
ELECTRICAL
Units are Single Phase; 950 Watts or as low as 300 Watts
(without heat) and available as specified in:
VOLTS
AMPS
WATTS
NO HEAT AMPS
NO HEAT WATTS
HERTZ
110-120V
7-7.7A
770-915W
3-3.2A
310-370W
50/60 Hz
208-277V
3.6-4A
735-950W
1.5-1.9A
300-375W
50/60 Hz
230V
3.9A
890W
1.7A
375W
50 Hz
EXCEL DRYER, Inc.
E a s t L o n g m e a d o w, M A Phone 1.800.255.9235
Fax 1.413.525.2853
Men
45" (114 cm)
Women
43" (109 cm)
Teenagers
41" (104 cm)
Small Children
35" (89 cm)
Accessible
37" (94 cm)
*Dry time and energy use testing performed by SGS International on standard Thin Air Hand Dryers to 0.25g or less
of residual moisture, pursuant to the UL Environment Global Product Category Rules (PCR) for Hand Dryers.
s a l e s @ e x c e l d r y e r. c o m
w w w . e x c e l d r y e r. c o m
FEB
2017
16TAT0006
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising