INFORMATION Cylinder Speed Checker (Built-in Magnet Cylinder) RoHS Speed (mm/s) 3 measurement Time required for stroke (s) modes Operation count (Times) Realizes increase in efficiency with visualization of air cylinder operation. Quantification of cycle time improvements For reduction of numerical management/adjustment labor when starting up equipment For reduction of numerical confirmation/inspection labor during periodic maintenance Caution Example of cycle time measurement T he measurement may not be performed with an air gripper or rotary actuator, or the measurement deviation may increase. Please contact SMC for more information. IN574-95/-73 14-E641 B IN574-95/-73 M 3 Measurement Modes Speed (mm/s) Measures the speed of cylinders. Sensor head Reverse direction (Rod retraction end) Rated measurement range Note) Positive direction –1999 to 1999 mm/s Note) Minus (-) is added to the measured value to distinguish the extension and retraction of a cylinder. Rod extension end: Positive direction Rod retraction end: Reverse direction (–) Red (Rod extension end) Green Stroke direction to be measured ∗ Although a measurement can be done even when the sensor is mounted in the reverse direction, the display direction is also reversed. Display part Cylinder Time required for stroke (s) Measures the time required for the stroke of the cylinder (rod retraction end to rod extension end). Timing chart (When rod extends) Rod retraction end Rated measurement range Rod extension end Field wireable connector (Refer to page 2.) Note) −999.9 to 999.9 s Note) Minus (-) is added to the measured value to distinguish the extension and retraction of a cylinder. Rod extension end: Positive direction Rod retraction end: Reverse direction (–) Measurement timing Time required for stroke Measurement start Operation count (Times) Time Y connector (Refer to page 2.) Auto switch (Refer to page 2.) Measurement end Display part Timing chart Measures the operation count of a cylinder for 1 minute. Cylinder Rated measurement range 0 to 999 times Count timing Measurement start Increase Count (1 time) Increase Count (2 times) M Compact: 40 (Width) x 110 (Height) x 20 (Depth) mm M Lightweight: Approx. 65 g (Body)/25 g (Sensor) ∗ Excluding dry cell batteries. M Battery powered: 2A dry cell battery x 2, continuous use for 15 hours or more. 1 M With backlight M With auto power-off function∗ ∗ If a button is not operated for 15 min. or more, the power supply will turn off automatically. Cylinder Speed Checker RoHS IN574-95/-73 How to Order Sensor head + Display part Sensor head IN574-95 IN574-73 Display part Sensor head Speed Measurement Type Model IN574-95 q Sensor head (q Sensor head + w Display part) w Display part q Sensor head w Display part Application example Time Required for Stroke/Operation Count Measurement Type + w Display part e Auto switch with pre-wired connector or r Auto switch with lead wire entry Order separately when using the time required for stroke/operation count measurement modes. Application example t Y connector e Auto switch with pre-wired connector w Display part e Auto switch with pre-wired connector D M9N S A PC Applicable auto switch ∗ The sensor head is not used when the checker is used for the time required for stroke/operation count measurement. Application example t Y connector Function Electrical entry Applicable model Grommet (In-line) M9N — Grommet (Perpendicular) M9NV M9NW 2-color Grommet (In-line) indication Grommet (Perpendicular) M9NWV M9NA Water Grommet (In-line) resistant Grommet (Perpendicular) M9NAV Ordering example · IN574-95 1 pc. Cylinder Speed Checker (Sensor head + Display part)∗ · D-M9NSAPC 2 pcs. Auto switch with pre-wired connector · PCA-1557798 1 pc. Y connector Connector model A M8-3 pin D M12-4 pin y Field wireable connector r Auto switch with lead wire entry Lead wire length S 0.5 m M 1.0 m w Display part ∗ Please contact SMC for other applicable auto switches. r Auto switch with lead wire entry t Y connector D M9N M8 M12 Ordering example 1 pc. · IN574-95 Cylinder Speed Checker (Sensor head + Display part)∗ · D-M9N 2 pcs. Auto switch with lead wire entry · PCA-1557730 2 pcs. Field wireable connector · PCA-1557798 1 pc. Y connector ∗ The sensor head is not used when the checker is used for the time required for stroke/operation count measurement. PCA-1557798 y Field wireable connector Applicable auto switch Function Electrical entry Applicable model Grommet (In-line) M9N — Grommet (Perpendicular) M9NV M9NW 2-color Grommet (In-line) indication Grommet (Perpendicular) M9NWV M9NA Water Grommet (In-line) resistant Grommet (Perpendicular) M9NAV M8 M8 Lead wire length 0.5 m Nil 1.0 m M ∗ Please contact SMC for other applicable auto switches. ∗ The lead wire is converted to M8/M12 connector for use. M12 M12 PCA-1557785 PCA-1557730 M8 Two auto switches with M8 connectors can be connected. M12∗ PCA-1557743 Two auto switches with M12 connectors can be connected. M12 M12 Attached to end of the lead wire of the auto switch. Used in combination with PCA-1557798. Attached to end of the lead wire of the auto switch. Used in combination with PCA-1557785. ∗ Note that although it can be connected, the IP65/67 may not be held depending on the assembly method. Refer to the WEB catalog for the details on the auto switches (e, r) and the M8/M12 connectors (t, y). 2 IN574-95/-73 Specifications Note 1) Environmental resistance Model IN574-95 Measurement mode Speed Time required for stroke Operation count (Times) Rated measurement range –1999 to 1999 mm/s –999.9 to 999.9 s 0 to 999 times Minimum 0.01 s (0.00 to 99.99 s, 0.00 to –99.99 s) 1 mm/s 1 time display unit 0.1 s (100.0 to 999.9 s, –100.0 to –999.9 s) Measurement accuracy — ±20% or less ±0.2 s or less 2 x 1.5 VDC 2A alkali dry cell batteries Note 2) Power supply (continuous use for 15 hours or more) Applicable cylinder Built-in magnet Enclosure IP40 Operating Operating: 0 to 40°C, Stored: –10 to 60°C temperature range (with no freezing or condensation) Operating Operating/Stored: 35 to 85% R.H. humidity range (with no condensation) Vibration 10 to 150 Hz at 1.5 mm amplitude or 98 m/s2 acceleration whichever is smaller, resistance in X, Y, Z directions for 2 hrs. each (De-energized) Impact resistance 100 m/s2 in X, Y, Z directions 3 times each (De-energized) Weight Sensor part: 25 g, Body: 65 g (excluding dry cell batteries) Standards RoHS, CE Speed Measurement Sensor/D-F8N Power supply voltage 4.5 to 28 VDC Current consumption 10 mA or less Load voltage 28 VDC or less Load current 40 mA or less Internal voltage drop 1.5 V or less (0.8 V or less at 10 mA) Leak current 100 µA or less Operating time 1 ms or less Indicator light Red LED is illuminated when turned ON. Ambient temperature –10 to 60°C Applicable Auto Switches for the Time Required for Stroke/ Operation Count Measurement Power supply voltage Output type ON voltage OFF current 14 VDC or less NPN open collector 2 V or less 100 µA or less Note 1) The above specifications may change depending on the operating environment. Note 2) 2A alkali dry cell batteries are not included, and must be acquired separately. Dimensions 20 IN574-95 (Sensor head + Display part) D-F8N (2 pcs.) 230 Red tape 110 20 40 500 Green tape M12 Connector Tube (3 places) Sensor head Wiring Terminal no. 1 Description +15 V Note — 2 Output signal 1 D-F8N 3 GND — 4 Output signal 2 D-F8N 2 1 3 4 Plug connector A-coded (Normal key) 5 1 2 4 3 Socket connector A-coded (Normal key) Display part Safety Instructions Be sure to read the “Handling Precautions for SMC Products” (M-E03-3) and “Operation Manual” before use.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project