Ergotron STSR2GM CPU SideRack Installation Manual

Add to my manuals
3 Pages

advertisement

Ergotron STSR2GM CPU SideRack Installation Manual | Manualzz

Built with Anthro-DNA ™

Anthro Steve's Station

TM

SideRack-Outboard

User's Guide

For the latest User Installation Guide please visit: www.ergotron.com

300-5564-00 rev. B • 06/16 1 of 3

04

02

08

03

01

PA R T S L I S T

Before beginning this assembly, please take a moment to review the parts listed below to verify that your shipment is complete. The Steve's Station table (shown shaded) is not included with this accessory.

01 Cross

02 Inside Arm (X)

03 Inside Arm (Y)

04 Outside Arm (X)

05 Outside Arm (Y)

06 Non-skid Pad

07 3-1/2" Bolt

08 1" MDF Wood Screw

09 Knob

1

4

1

1

1

1

125-4192-00

225-4397-00

225-4398-00

225-2454-00

225-2455-00

175-5148-00

2

4

2

325-5000-00

325-5580-00

325-5213-00

07

TO O L S

The Anthro 5/32" hex driver, provided with your Steve's Station table, is required for this installation.

09

05

S T E P 1

Install the Inside Arms

 Your Steve's Station SideRack-Outboard can be installed on the left or the right. Choose the side.

 Locate the set of four installation holes on each side of the table, next to the leg. One at a time, align the Inside Arms with the holes on the table.

The tabs on the top of each arm should bend toward each other when installed. Attach each arm to the table with two 1" MDF Wood Screws using the Anthro driver.

1” Button Hd PB Screw

325-5580-00

2 of 3 300-5564-00 rev. B • 06/16

S T E P 2

Install the Cross Tube

 Align the Cross Tube with the Inside Arms. Loosely attach using two

3-1/2" Tube Bolts. Check that the SideRack is level, then tighten the screws.

 Tighten the screws that attach the SideRack to the top and to the side gussets.

3-1/2” Bolt

325-500 0-00

S T E P 3

Adjust the Outside Arms

 Align Outside Arm X with Inside Arm X, inserting the Pin on the Inside

Arm through the Slot on the Outside Arm.

 Align the Slot with the threaded hole and carefully thread the Knob into the hole.

 Repeat for Inside and Outside Arm Y.

S T E P 4

Install the Adhesive Pads & Adjust your SideRack

 Install the four Adhesive Pads onto the tabs on the Arms.

 To adjust your SideRack, loosen the knobs and slide the Outside Bracket to fi t your CPU.

 Place your CPU into the SideRack, slide the brackets back in, and tighten the Knobs.

CO N G R AT U L AT I O N S ! YO U R S I D E R AC K - O U T B OA R D A S S E M B LY I S CO M P L E T E !

For Warranty visit: www.ergotron.com/warranty

For Service visit: www.ergotron.com

For local customer care phone numbers visit: http://contact.ergotron.com

© 2016 Ergotron, Inc. All rights reserved.

All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.

Anthro-DNA is a trademark of Ergotron Inc., Ergotron Inc.

300-5564-00 rev. B • 06/16 3 of 3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

What are the components of Ergotron STSR2GM?
It consists of a Cross Tube, Inside Arms (X and Y), Outside Arms (X and Y), 3-1/2" Tube Bolts, 1" MDF Wood Screws, Knobs, and Adhesive Pads.
Which tools do I need for installation?
You will need an Anthro 5/32" hex driver, which is usually provided with the Steve's Station table.
Can I install the SideRack-Outboard on either side of the table?
Yes, you can choose to install the SideRack-Outboard on the left or right side of the Steve's Station table.
How do I attach the Inside Arms to the table?
Align the Inside Arms with the installation holes on the table, next to the leg. Secure each arm using two 1" MDF Wood Screws with the Anthro driver.
How do I adjust the Outside Arms?
Align Outside Arm X with Inside Arm X, insert the Pin on the Inside Arm through the Slot on the Outside Arm, align the Slot with the threaded hole, and carefully thread the Knob into the hole. Repeat the process for Inside and Outside Arm Y.

Related manuals

Download PDF

advertisement