Specific Lighting

Specific Lighting
Specific Lighting
Product Data Sheet
LTPL-C035GH530
Spec No.: DS23-2016-0106
Effective Date: 12/14/2016
Revision: -
LITE-ON DCC
RELEASE
BNS-OD-FC001/A4
LITE-ON Technology Corp. / Optoelectronics
No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.
Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660
http://www.liteon.com/opto
Specific Lighting
LTPL-C035GH530
1. Description
The LiteON C034 Product is a revolutionary, energy efficient and ultra-compact new light source, combining the lifetime
and reliability advantages of Light Emitting Diodes with the brightness of conventional lighting. It gives you total design
freedom and unmatched brightness, creating a new opportunities for solid state lighting to displace conventional lighting
technologies.
Features




I.C. compatible
RoHS compliant and Pb free
Lower operating costs
Reduced maintenance costs
2. Outline Dimensions
Notes :
1.
All dimensions are in millimeters and dimension tolerances are ± 0.2mm except lens height and ceramic
length / width dimension tolerance are ± 0.1mm
2.
Thermal pad of the device is electrically neutral from the anode and cathode pads
1/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
3. Absolute Maximum Ratings at Ta=25°C
Parameter
Symbol
Rating
Unit
DC Forward Current
If
500
mA
Power Consumption
Po
1.9
W
Operating Temp Range
Topr
-40 ~ +85
°C
Storage Temp Range
Tstg
-55 ~ +100
°C
Junction Temperature
Tj
125
°C
Notes:
Operating the LED under reverse bias condition long time might result in damage or failure of the component.
2/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
4. Electro-Optical Characteristics at Ta=25°C
Parameter
Forward Voltage
Luminous Flux
Dominant Wavelength
Symbol
Vf
lm
Values
Min.
2.6
Typ.
3.0
Max.
3.8
Min.
90
Typ.
120
Max
150
Min.
520
Max
540
Wd
Test Condition
Unit
If = 350mA
V
If = 350mA
mW
If = 350mA
nm
Viewing Angle
2θ1/2
Typ.
130
If = 350mA
°
Thermal Resistance
Rthjc
Typ
9
---
°C/W
Notes:
1. Luminous flux (lm) is the total Luminous flux output as measured with an integrating sphere.
2. Thermal resistance (Junction to case) measurement tolerance is ± 10%
3/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
5. Bin Code List
Vf : Forward Voltage Spec. Table
Vf (V) @ If = 350mA
Vf Bin
Min.
Max.
V0
2.6
3.0
V1
3.0
3.4
V2
3.4
3.8
Forward Voltage Tolerance: +/- 0.1 V
lm Luminous Flux Spec. Table
Φe (mW) @ If = 350mA
lm Bin
Min.
Max.
L1
90
110
L2
110
130
L3
130
150
Luminous Flux Tolerance: +/- 10%
Wd: Dominant Wavelength Spec table
Wd (nm) @ If = 350mA
Wd Bin
Min.
Max.
D5E
520
525
D5F
525
530
D5G
530
535
D5H
535
540
Dominant Wavelength Tolerance: +/- 3nm
Notes:
1.
Bin classification code is marked on each packing bag.
2.
If there is any special or limited bin request, please contact with LiteOn’s sales
4/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
6. Typical Electrical / Optical Characteristics Curves
(25C Ambient Temperature Unless Otherwise Noted)
Fig 1. Relative Luminous Flux vs. Forward Current
Fig 2. Relative Spectral Distribution
5/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
Fig 3. Radiation Characteristics
Fig 4. Forward Current vs. Forward Voltage
6/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
Fig.5 Relative Luminous Flux vs Case Temperature
7/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
7. Reliability Test Plan
No
Test item
Condition
Duration
Number
of Failed
Low Temperature Operating Life
1
Tc= -30°C, IF=350mA
1000 hrs
0/10
25°C, IF= 350mA
1000 hrs
0/10
Tc=85°C, IF= 60mA
1000 hrs
0/10
60°C/90%RH, IF= 350mA
500 hrs
0/10
100 cycles
0/10
1000 hrs
0/10
(LTOL)
Room Temperature Operating Life
2
(RTOL)
High Temperature Operating Life
3
(HTOL)
Wet High Temperature Operating Life
4
(WHTOL)
Non-Operating Thermal Shock
-40°C to 125°C
(TMSK)
30minutes dwell, <10 seconds transfer
High temperature storage
TA=100°C
5
6
Notes:
1. Operating life test are mounted on thermal heat sink
2. Storage item are only component, not put on heat sink.
Criteria for Judging the Damage
Criteria for Judgment
Item
Symbol
Test Condition
Min.
Max.
Forward Voltage
Vf
If = Typical Current
-10%
+10%
Luminous Flux
lm
If = Typical Current
-15%
+15%
8/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
8. User Guide
Suggested Reflow Soldering Characteristics
Notes:
1.
All temperatures refer to topside of the package, measured on the package body surface.
2.
The soldering profile could be further referred to different soldering grease material characteristic. The grease
vendor will provide this information.
3.
A rapid-rate process is not recommended for the LEDs cooling down from the peak temperature.
4.
Although the recommended reflow conditions are specified above, the reflow or hand soldering condition at
the lowest possible temperature is desirable for the LEDs.
5.
LiteOn cannot make a guarantee on the LEDs which have been already assembled using the dip soldering
method.
9/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Recommend Printed Circuit Board Attachment Pad
Specific Lighting
LTPL-C035GH530
Notes:
1.
The LEDs can be soldered using the reflow soldering or hand soldering method. The recommended hand
soldering condition is 300°C max. and 2secs max. only once, and the operation of reflow soldering is only up to
three times at maximum.
2.
All temperatures refer to topside of the package, measured on the package body surface.
3.
The soldering profile could be further referred to different soldering grease material characteristic. The grease
vendor will provide this information.
4.
A rapid-rate process is not recommended for the LEDs cooling down from the peak temperature.
5.
Although the recommended reflow conditions are specified above, the reflow or hand soldering condition at
the lowest possible temperature is desirable for the LEDs.
6.
LiteOn cannot make a guarantee on the LEDs which have been already assembled using the dip soldering
method.
10/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
Package Dimensions of Tape
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 7 inch reel-maximum 500 pieces per reel.
3. The maximum number of consecutive missing lamps is two.
4. In accordance with EIA-481-1-B specifications.
11/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
9. Cautions
Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
Do not use unspecified chemical liquid to clean LED, it could harm the package.
Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel
in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with
each LED as shown in Circuit below.
LED
Circuit model A
LED
Circuit model B
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those
LEDs.
(C) This LED should be used under forward current, particularly not used under continuous reverse current to avoid
the damage to LED.
The electrode pads are plated with gold, but it is still not recommended to the use under any of the following
conditions, please confirm the performance and reliability are well enough if you use it under any of the following
conditions
・Do not use sulfur-containing materials in commercial products including the materials such as seals and
adhesives that may contain sulfur.
・Do not put this product in a place with a lot of moisture (over 85% relative humidity), dew condensation, briny air,
and corrosive gas (Cl, H2S, NH3, SO2, NOX, etc.).
Manual Handling Remark
The LED should only be picked up by making contact with the sides of the LED body. It should not put any pressure
on the lens either by finger or any hand tool. Do not puncture or push the lens.
12/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:
・Use a conductive wrist band or anti-electrostatic glove when handling these LEDs.
・All devices, equipment, and machinery must be properly grounded.
・Work tables, storage racks, etc. should be properly grounded.
・Use ion blower to neutralize the static charge which might have built up on surface of the
LED’s plastic lens as a result of friction between LEDs during storage and handling.
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward
voltage, or “no light up” at low currents. To verify for ESD damage, check for “light up” and V F of the suspect LEDs
at low currents. The VF of “good” LEDs should be >2.0V@0.5mA.
Training and Certification
1.
Working area is ESD-certified.
2.
Training records and re-certification dates monitored.
Static-Safe Workstation & Work Areas
1.
Static-safe working stations or work-areas have ESD signs.
2.
All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V.
3.
All ionizer activated, positioned towards the units.
4.
Each work surface mats grounding is good.
Personnel Grounding
1.
Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring.
2.
If conductive footwear used, conductive flooring also present.
3.
Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V.
4.
The wrist strap or heel strap/conductive shoes are checked daily and result recorded.
5.
All wrist strap or heel strap checkers calibration up to date.
Device Handling
1.
Each ESDS items identified by EIA-471 labels on item or packaging..
2.
No static charge generators (e.g. plastics) inside shielding containers with ESDS items.
3.
All flexible conductive and dissipative package materials are inspected before reuse or recycles
13/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
Storage
This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handling this
moisture sensitive product is important to ensure the reliability of the product.
The package is sealed:
The LEDs should be stored at 30°C or less and 85%RH or less. And the LEDs are limited to use within one year,
while the LEDs is packed in moisture-proof package with the desiccants inside.
The package is opened:
The LEDs should be stored at 30°C or less and 60%RH or less. The LEDs are limited to solder process within
168hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the storage limiting time since
opened, we recommended to baking LEDs at 60°C at least 24hours before solder. To seal the remainder LEDs
return to package, it’s recommended to be with workable desiccants in original package.
14/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Specific Lighting
LTPL-C035GH530
10. Datasheet Version:
Version
Date
Owner
1.
2016/6/14
ChunChieh
2.
2016/8/29
ChunChieh
Change Item
Initial Version
Change Radiant Flux Bin to Luminous Flux Bin
P.4
Change Peak Wavelength Bin to Dominant Wavelength Bin
P.4
15/15
Part No. : LTPL-C035GH530
BNS-OD-FC002/A4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising