IVES Architectural Hardware Products Catalog

IVES Architectural Hardware Products Catalog
Architectural
hardware
products
i
Ives Architectural hardware products
Table of Contents
A
Hinges & Pivots
page
Terms and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii-vi
Index by Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Index by Part Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Finish Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Packaging, Handing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
B
Pulls & Plates
A - Hinges and Pivots
Architectural Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2 - A11
Residential Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
Continuous Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A13 - A30
Pivots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A31 - A49
Pocket Pivot/Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A50
C
Flush Bolts & Coordinators
B - Pulls and Push Plates
Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2 - B8
Push Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8 - B9
Vandal Resistant Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B10 - B12
Protection Plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13 - B14
Mounting Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B15 - B17
C - Flush Bolts & Coordinators
Flush Bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C2 - C11
Coordinators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12 - C16
D
Latches, Catches & Bolts
D - Latches, Catches & Bolts
Surface Bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2 - D6
Door Guards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
Roller Latches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D8 - D10
Angle Stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D11
Latches/Catches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12 - D16
E
Stops
E - Stops
Floor Stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2 - E5
Stops & Holders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6 - E8
Wall Bumpers/Stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9 - E14
Wall Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
Kick Down Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E16 - E17
Plunger Door Holders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E17
Roller Bumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19
Residential Door Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20 - E21
Hinge Pin Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21 - E22
Silencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23
Exterior Hardware
F
F - Exterior Hardware
Lock Guards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2 - F4
Door Viewers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5 - F6
Door Knockers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7
Letter Box/Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
Door Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
Storm Door Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
Screen Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
Crash Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
Miscellaneous Hardware
Ives Architectural hardware products
G
G - Miscellaneous Hardware
Hooks & Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2 - G6
Window Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6 - G8
Hobby Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9 - G12
Cabinet/Closet Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13 - G16
ii
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Terms and Conditions
iii
1. GENERAL/ACCEPTANCE. (a) This Agreement contains the only terms and conditions
by which Company will quote and sell Deliverables to Customer; (b) The terms “purchase
order” or “order” for the purposes of this Agreement include the term “request for quotation,”
as appropriate; (c) This Agreement supersedes all pre-printed or boilerplate terms and
conditions set forth in any purchase order issued by Customer; (d) No reference herein to
Customer’s purchase order will in any way incorporate different or additional terms and
conditions, all of which Company hereby expressly objects to; (e) ANY ACCEPTANCE BY
COMPANY OF CUSTOMER’S PURCHASE ORDER IS EXPRESSLY CONDITIONED ON
THE CUSTOMER’S ASSENT TO AND ACCEPTANCE OF THE TERMS AND CONDITIONS
CONTAINED IN THIS AGREEMENT; (f) Company reserves the right to decline any order, in
whole or in part, for any reason.
2.ORDERS.
a. Order Processing. When Customer wishes to place an order for Deliverables, it will
deliver to Company a purchase order. All such purchase orders must (i) be in a written format
acceptable to Company, (ii) be legible, (iii) include a purchase order number, (iv) include
Customer’s account number, invoice address, ship to address, shipping method, shipper’s
letter of instruction for international shipments, part number, pricing, and designated contact
information, (v) include, if applicable, any special configuration ID numbers, necessary
programming information, special factory instructions, and requested specifications regarding
a particular finish, handing, design, backset, or strike, and (vi) reference any applicable pricing
discounts under an ongoing buying program or based on a written quote from Company,
along with the applicable buying program number or quotation number.
b. Minimum Orders. In the event the order value does not meet any required minimum
net Deliverable value, Company may, at its sole discretion, (i) increase the quantity of items
in the order to meet the minimum net Deliverable value requirement; (ii) apply a minimum
order charge; (iii) reject the order, or (iv) waive the requirement, provided that the waiver of
a requirement for one order shall not constitute a waiver of the requirement for any future
orders.
c. Acceptance of Purchase Orders. Company will endeavor to (i) acknowledge receipt
of each purchase order issued in accordance with this Agreement, and (ii) notify Customer
whether Company accepts or rejects the purchase order. If Company fails to accept or reject
a purchase order within a reasonable time period, such failure to respond will be deemed a
rejection of the entire order.
d. Changes to Order/ Cancellation of Orders. Additional terms and conditions regarding
order changes and cancellations are available on the Allegion customer website, WHICH
TERMS ARE EXPRESSLY INCORPORATED HEREIN BY REFERENCE. Unless otherwise
provided herein, Customer acknowledges that (i) requesting a Change Order may cause
a delay in the scheduled shipment date, a longer lead time or result in a new scheduled
shipment date; (ii) Orders may not be changed after 48 hours of Company’s order
acknowledgment; (iii) After 48 hours of Company’s order acknowledgment, all changes
to an accepted purchase order will be subject to a Change Order charge of 25% of the net
Deliverable value, plus the cost of labor and fabrication or raw material that Company
incurred prior to the receipt of the Change Order from Customer, or that may be required due
to the Change Order; (iv) the requested change may result in additional charges for labor,
fabrication, and raw material, and (v) if Customer cancels an order or portion of an order
that includes Deliverables that have been manufactured and prepped for shipping, a 35%
restocking fee will apply. Notwithstanding the foregoing, Customer cannot change or cancel
credential orders, reader orders, biometrics orders or any non-cataloged, special, Custom or
nonstandard items once they have been placed. All cancelled orders for a Non Recurring
Expense (NRE), credential orders, reader orders, biometrics orders, and/or Custom orders will
be subject to a cancellation charge of 100% of the acknowledged price.
e. Add-ons. Add-on orders will not be accepted. Additions to orders will be entered as
separate stand-alone orders and must qualify for all terms of sale, including discounts, on an
individual basis.
f. Fast-Track Orders. No changes or cancellations will be accepted on the 24-Hour
Fast Track Program. For 3-day Fast Track orders, changes and cancellations may only be
requested by Customer within 24 hours of Company’s order acknowledgment if the order has
not shipped. For 5-Day Fast Track orders, changes and cancellations may only be requested
by Customer if the order has not shipped and if the request is made to Company within
48 hours of Company’s order acknowledgment. Return Material Authorization (RMA) for
Deliverables must be processed through Fast Track Customer Service.
g. Steelcraft Orders. For all Steelcraft orders, changes or cancellations are allowed
without penalty only if made within 48 hours of Company’s order acknowledgment, and
provided that the order has not shipped. Some exceptions do apply – please consult the
factory. Changes are not allowed on Rapid Program orders after the order has been entered
and acknowledged. After 48 hours of Company’s order acknowledgment, all changes or
cancellations are subject to a charge of 25% of the order. Unless otherwise specified by
Company in writing, any changes to orders acknowledged by Company that affect the delivery
date will be deemed a new order and will require acknowledgement by Company as provided
in this Section. Additional products, features, terms and conditions regarding the Rapid
Program are available on the Allegion, WHICH TERMS ARE EXPRESSLY INCORPORATED
HEREIN BY REFERENCE.
3. PRICES, INVOICES AND PAYMENT.
a. Prices. The prices in Company’s Price Book are subject to change at any time, without
notice to Customer. Company may charge Customer additional amounts if Customer requests
special packing, marking, shipment, product modification, or engineering services. Oral prices
specified by Company are null and void. Quote numbers must be referenced on Customer’s
purchase order in order for the Company’s quoted pricing to apply. Orders that do not
reference a quote number will receive buy program pricing or book net pricing. Quoted prices
are for those specific products quoted for a specified job, and are subject to the Price Book in
effect at the time the quote was issued by Company.
b. Taxes. Prices do not include any present or future federal, state or local property,
license, privilege, sales, use, excise, gross receipts or other like taxes or assessments which
may result from transactions or any services performed in connection therewith. Any taxes,
charges, or duties imposed by any governmental authority on the sale of Deliverables will be
paid by Customer, in addition to the selling price specified by Company.
c. Payment Terms. Company will deliver to Customer an invoice with each shipment of
Deliverables hereunder. Customer will pay all invoiced amounts within 35 days of the invoice
date, provided that Customer may take a 2% discount if Customer pays in cash and Company
receives said payment within 20 days of the invoice date. For the avoidance of doubt, cash
discounts do not apply to credit card payments. Customer will make all payments in United
States dollars. Past due invoices will be subject to a late payment service charge of 1.5%
per month on any overdue unpaid balance, equivalent to 18% per annum, or the maximum
rate permitted by law, whichever is less. Customer shall reimburse Company for all costs of
collection, including, without limitation, reasonable attorneys’ fees, for any overdue amount
Ives Architectural hardware products
owed by Customer to Company, and such collection costs shall also be subject to interest
charges.
4.QUOTATIONS.
a. Project Quotations. Project or new construction quotes are restricted to the specific
project quoted for the quantities, finishes, and series of Deliverables referenced on the quote.
Company reserves the right to require proof of sale of Company products for any quoted
project.
b. Stock Quotations. Deliverables fulfilling stock quotations may only be used for the
following: i) Stocking of the Customer’s shelves for small, quick-turn, discretionary projects,
or ii) Sale to a general contractor or installer for new construction. Stock quotations may
not be used for any project containing any Company no-substitution, specified products.
Deliverables purchased under Stock Quotations cannot be redistributed to other Customer
branch locations or re-sold to other resellers or used for aftermarket sales, end-user annual
contracts or sold over the counter to any walk in trade.
c. General. All quotes are subject to this Agreement, unless otherwise specified by
Company, and are subject to change at any time prior to Company’s acceptance of a purchase
order referencing the applicable quote number. Company, its representatives and employees
reserve the right, in their sole discretion and for any reason, to refuse a Customer’s request
to quote a price other than the standard list price, regardless of whether Company or its
representatives or employees have previously quoted discounted prices to the Customer on
some or all of its orders. Customer’s failure to comply with this Section 4 will be considered
a material breach of this Agreement, and will entitle Company to immediately terminate any
purchase orders and/or Customer’s ability to distribute Company’s products.
5. SECURITY INTEREST. Customer grants Company, and Company retains, a purchase
money security interest and lien on any and all of Customer’s rights, title and interest in
each Deliverable sold by Company to Customer, wherever located, until the invoice for the
applicable Deliverable(s) is paid in full, including any late charges and costs of collection.
Customer authorizes Company to, and will assist Company in, taking all necessary steps to
perfect and maintain Company’s interest in such Deliverables.
6. CREDIT TERMS. Unless Customer pre-pays all of its purchase orders in advance, its
purchase orders will be subject to the credit limit and other terms of credit (“Credit Terms”)
set forth in Company’s credit application, which Credit Terms Customer acknowledges are
subject to change by Company at any time. Company reserves the right to request payment
in advance of shipment or any order or to request adequate assurances for Customer’s
payment of an order and may withhold or stop shipment, without any liability to Company,
until Customer submits payment or adequate assurance of payment.
7. RESALE OF DELIVERABLES. Customer agrees and warrants that it will offer Company
products in support of Company-written specifications and will maintain sufficient inventory
to adequately support End Users, installers, and/or general contractors’ needs. Customer
will adhere to any MSRP or resale pricing programs of Company. Failure to comply with this
provision will be considered a material breach of this Agreement, and will entitle Company to
immediately terminate any purchase order and/or Customer’s ability to distribute Company’s
products. Customer shall, at its own expense, gain and maintain sufficient knowledge of the
industry and products competitive with Deliverables so as to be able to (a) explain in detail to
End Users, installers, and/or general contractors the differences between the Deliverables and
competing products, (b) ensure that an adequate number of trained, capable and qualified
technical personnel with sufficient knowledge of the Deliverables and who have obtained all
necessary licenses and permits are available to assist End Users, installers, and/or general
contractors, and (c) respond to such End Users, installers, and/or general contractors with
respect to the general operation and use of the Deliverables including, but not limited to, (1)
acting as a liaison between the End Users, installers and/or general contractors and Company
in matters requiring Company participation, (2) providing general product information and
configuration support on standard protocols and features, (3) collecting relevant technical
problem identification information, and (4) posting and distributing any warranty information
concerning the Products in accordance with Company’s instructions. Customer is responsible
for all service and support resulting from the re-sale of any Deliverable to End-Users, installers
and/or general contractors, examples of which may include, but are not limited to, support
activities such as installation, initialization, software set-up, training, trouble-shooting,
technical support and field service. In the event Customer is unwilling or unable to perform
said support activities, Company reserves the right to recover from Customer any and all
expenses incurred by Company to resolve the afore-mentioned End-User, installer and/or
general contractor issues. Technical product training is recommended for Customer in order to
fully service and support Deliverables purchased from Company that are resold to End-Users,
installers and/or general contractors.
8. DEFAULT. If Customer is in default of payment or otherwise with respect to any purchase
order or other contract with Company, Company shall have the right, in addition to all other
legal remedies and without prejudice to any of its right hereunder, to defer further shipments
under that or any other purchase order until such default is corrected and to declare all
outstanding bills of Customer to be immediately due and payable.
9. INSPECTION AND DELIVERY.
a. Inspection. Customer will inspect all Deliverables immediately after receiving them.
Customer will be deemed to have accepted the Deliverables unless Customer notifies
Company in writing of any nonconformance within 10 days of delivery and provides Company
written evidence reasonably documenting that nonconformance. Inspection of Deliverables at
Company’s facility is not permitted.
b. Delivery. Delivery schedules for Deliverables are based upon current production
capacities, material or component availability, and inventory, and may be changed by
Company as conditions require. Delivery schedules for services are based upon Company’s
prompt receipt of, and prompt access to, Customer’s equipment and all information necessary
to complete the services. In no event will any delivery date be construed as falling within
the meaning of “time is of the essence.” Partial delivery shall be accepted by Customer and
paid for at the price and on the terms stated herein. Any partial delivery shall constitute a
separate sale, and payment shall be separately made when due. If any part of a delivery
hereunder is not delivered by Company in accordance with Customer’s purchase order, this
Agreement shall not be affected thereby.
10. TITLE & RISK OF LOSS. Unless otherwise specified by Company, (i) where the Customer
is located in the United States, all Deliverables will be sold “Uniform Commercial Code, FOB
Origin, Company’s factory”; and (ii) where the Customer is located outside of the United
States, all Products will be sold “Ex-works, Company’s factory (Incoterms 2010).” In either
instance, title and risk of loss will pass to Customer upon delivery to the carrier at Company’s
Terms and Conditions
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
D
17. TRADEMARKS. Except as agreed to by Company in writing, Customer agrees not to (a)
use Company’s name in any form of publicity; or (b) use, create, register or market, directly or
indirectly, in whole or in part, Company’s names, logos, brands, or any other trademarks, or
names that are now or may hereafter be owned by Company, as part of Customer’s corporate
or business name, as part of an internet domain name, uniform resource locator (URL), or
in any way connected with Customer’s business, trade address or other designations. Upon
termination of this Agreement or upon the request of company for any reason, any use of
Company’s trademarks or names will be immediately discontinued.
20. INDEMNIFICATION AND LIMITATION OF LIABILITY. a. Customer shall indemnify,
defend and hold Company, and its officers, directors, employees, customers, Affiliates,
suppliers, users and agents, (collectively the “Indemnitees”) harmless from and against any
and all damages, claims, losses, expenses, costs, obligations, liabilities, including without
limiting the generality of the foregoing, liabilities for court costs and attorneys’ fees, suffered
directly or indirectly by an Indemnitee by reason of, or arising out of any injury, death or loss to
any person, or injury to any property (collectively, “Damages”), received
or sustained by any person(s) or property, arising out of, occasioned by, attributable or related
to i) any breach of any representation or warranty made by Customer, its officers, directors,
employees, affiliates, users, agents, representatives or customers to Company or any third
party, (ii) any failure by Customer to perform or fulfill any of its covenants, acts and/or
omissions to Company or to any third party, or (iii) any litigation, proceeding or claim by any
third party relating in any way to the obligations of Customer and/or the Deliverables sold by
Company to Customer hereunder. Customer shall not consummate any settlement of any
indemnified claim without the Indemnitees’ prior written consent. Customer’s obligation to
Latches, Catches & Bolts
16. CONFIDENTIAL INFORMATION.
a. Non-Use And Non-Disclosure. Customer shall not use the Confidential Information of
the Company except for the purpose of performing its obligations under this Agreement or
exercising the rights granted herein (the “Purpose”). Customer shall protect Confidential
Information of the Company from disclosure and unauthorized use in the same manner that
it protects its own Confidential Information, but in no event shall such standard of care be
less than reasonable care. Customer may disclose Confidential Information of the Company
only to its employees who require such information for the Purpose and who are subject to
confidentiality obligations at least as protective as those set forth herein.
b. Proprietary Information and Advice. (a) All designs, data, and specifications provided by
Company are proprietary and may not be disclosed or reused by Customer without the prior
written consent of Company; (b) Company assumes no obligation or liability for any advice
given by Company, the results obtained, or damages incurred as a result of such advice, and all
such advice is given and accepted at Customer’s risk.
c. Return. Upon the termination or expiration of a purchase order or this Agreement or upon
the request of the Company, the Customer agrees to end all further use of, to immediately
return to the Company the original version of, and to delete or destroy all copies of, any and all
Confidential Information of the Company.
19. LIMITATION OF REMEDIES.
CUSTOMER’S EXCLUSIVE AND SOLE REMEDY ON ACCOUNT OF, OR IN RESPECT
OF, THE FURNISHING OF NON-CONFORMING DELIVERABLES, SHALL BE TO (A)
SECURE REPAIR OR REPLACEMENT OF THE PRODUCTS; OR (B) SECURE REPAIR
OR RE-PERFORMANCE OF THE SERVICES OR TO OBTAIN A REFUND OF THE
PRICE PAID FOR THE DEFECTIVE SERVICE, ALL AT COMPANY’S OPTION. IN NO
EVENT WILL THE COMPANY’S MAXIMUM LIABILITY EXCEED THE SELLING PRICE
FOR THE DELIVERABLE. THE WARRANTY, OBLIGATIONS AND LIABILITIES OF
COMPANY (INCLUDING ITS SUPPLIERS) AND THE RIGHTS AND REMEDIES OF
CUSTOMER ARE EXCLUSIVE AND ARE IN LIEU OF AND CUSTOMER HEREBY WAIVES
AND RELEASES ALL OTHER WARRANTIES, OBLIGATIONS, REPRESENTATIONS
OR LIABILITIES EXPRESS OR IMPLIED ARISING BY LAW, IN CONTRACT, TORT
(INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO (I) ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR ANY WARRANTY IMPLIED THROUGH COURSE
OF PERFORMANCE, COURSE OF DEALING, OR USAGE OF TRADE OR (II) CLAIMS
ARISING OUT OF THE NEGLIGENCE OF COMPANY OR COMPANY’S SUPPLIERS OR
(III) ANY OTHER CLAIM ARISING OUT OF, CONNECTED WITH, OR RESULTING FROM
THE PERFORMANCE OF COMPANY OR FROM THE DESIGN, MANUFACTURE, SALE,
REPAIR, LEASE OR USE OF THE DELIVERABLE, OR ANY COMPONENT THEREOF,
DELIVERED OR RENDERED HEREUNDER OR OTHERWISE.
C
15. PRODUCT RETURNS. Unless otherwise agreed by the parties in writing, Deliverables
that are correctly furnished by Company per the purchase order may not be returned
unless Customer receives written authorization from Company. If returns are authorized
by Company, a return merchandise authorization (“RMA”) number must be provided by
Company. Deliverables identified under such RMA must be returned to Company within 90
days of issuance of the RMA. Such RMA number and any accompanying RMA documents, the
original invoice number, and a written explanation for the return must be included with the
returned Deliverables in order for Company to inspect and approve a credit for the return. For
warranty returns, a credit in the amount of the original purchase price will only be issued if,
after Company’s receipt and inspection of the returned Deliverables, Company confirms, in
its sole discretion, the defect is valid and approves the return. For non-warranty returns, (a)
in the event Company approves such a return, a credit will be made to Customer’s account
in the amount of the original purchase price less freight and a handling charge of 35% of
the net material on the original invoice; and (b) Only Deliverables that are new, current,
standard, non-obsolete, non-specially manufactured, unused, in their original condition as
at the time of sale by Company to Customer, in their original packaging and in Customer’s
inventory less than 180 days from the date of shipment by the Company may be considered by
Company for return. Such credit will only be issued if, after Company’s receipt and inspection
of Deliverables, Company approves the return. The amount of final credit will be determined
upon receipt at the factory and following Company’s inspection and analysis of the condition
of the returned material. Company retains the right to deny credit to anyone for any reason.
Flush Bolts & Coordinators
14. PRODUCT USAGE LIMITATION. Customer agrees: (i) not to sell or use a Deliverable in
any manner contrary to the manner in which the Deliverable is intended to be used; and/or
(ii) not to modify the design of any Deliverable for use with another product without the prior
written consent of Company.
B
13. PRODUCT CHANGES. Company’s product policy is one of ongoing update and revision,
and accordingly, Company reserves the right to change, without notice, the design of, or the
process of manufacturing, the Deliverables covered by this Agreement.
Pulls & Plates
12. CLAIMS. All claims must be submitted in writing to Company as follows: (i) All claims
for prices must be submitted within thirty (30) days from the date of invoice; (ii) All claims
regarding Deliverable quantity or incorrect orders must be submitted within ten (10) days from
the date of delivery; (iii) All claims for damage to Deliverables (while in the care, custody, and
control of Company) must be submitted within thirty (30) days from the date of invoice; (iv)
All claims for loss or damage to Deliverables while in the care, custody, and/or control of a
carrier will be the responsibility of Customer, unless otherwise agreed by the parties.
A
11.SHIPPING & SHIPPING PROGRAMS.
a. Freight Charges. Company will ship all Deliverables in accordance with Company’s freight
shipment guidelines, which are set forth on the Allegion customer website (“Freight Shipping
Guidelines”), WHICH TERMS ARE EXPRESSLY INCORPORATED HEREIN.
b. Rush Charges. Expedited order options are available as set forth in Company’s freight
shipping guidelines.
c. Packing and Marking. Company will pack, mark, and ship Deliverables according to its
standard procedures for shipment, unless the parties agree, in writing, that Company will
comply with any special instructions provided by Customer. Special instructions may result in
an increased price.
d. International Shipments. For all international orders, a Shipper’s letter of instruction
must be submitted in writing with the order. Failure to do so will result in the order being
rejected. Complete adherence to this order requirement will be strictly enforced. Company
will not be held liable for any charges resulting from delays due to lack of complete required
information being supplied.
e. Once received by the Company, a purchase order cannot be combined with any other order
to qualify for freight allowances. In addition, Customer may not combine any Company brands
or product categories on a single order to meet the applicable net freight allowance, except
in the case of: i) FastTrack 24 Hour/5 Day Program, which is available for Schlage, Von Duprin,
LCN and Glynn-Johnson products; ii) FastTrack 24 Hour/3 Day Program, which is available for
Falcon Locks, Exits and Closers and Ives products. When an order includes products from the
brands listed in both (i) and (ii) above, the order will automatically default to the FastTrack
24 Hour/5 Day Program lead times and freight allowance.
18. LIMITED WARRANTY.
COMPANY MAKES NO OTHER WARRANTIES EXCEPT THOSE STATED IN
COMPANY’S LIMITED WARRANTY IN EFFECT ON THE DATE COMPANY
ACCEPTS EACH APPLICABLE PURCHASE ORDER (“LIMITED WARRANTY”).
THE LIMITED WARRANTY MAY BE FOUND IN THE APPLICABLE PRICE BOOK
AND ON THE ALLEGION CUSTOMER WEBSITE, WHICH TERMS ARE EXPRESSLY
INCORPORATED HEREIN BY REFERENCE. COMPANY WILL MAIL CUSTOMER A
HARD COPY OF THIS WARRANTY UPON CUSTOMER’S WRITTEN REQUEST. IN
THE EVENT THAT CERTAIN DELIVERABLE WARRANTIES ARE NOT FURNISHED
BY THE COMPANY TO CUSTOMER, COMPANY WARRANTS ONLY TO CUSTOMER
THAT THE DELIVERABLES WILL BE FREE FROM DEFECTS IN MATERIAL AND
WORKMANSHIP FOR A PERIOD OF 12 MONTHS FROM THE DATE OF SHIPMENT OF
THE DELIVERABLES. COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY IS
LIMITED TO REPAIRING OR REPLACING, AT COMPANY’S OPTION, THE DEFECTIVE
DELIVERABLE, PROVIDED WRITTEN NOTICE OF THE DEFECT OR NONCONFORMANCE
IS PROVIDED BY CUSTOMER WITHIN 30 DAYS OF DISCOVERY OF THE DEFECT OR
NONCONFORMANCE. COMPANY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, WITH RESPECT TO THE DELIVERABLES, INCLUDING BUT NOT LIMITED
TO, ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR A PARTICULAR PURPOSE.
a. Exclusions. The provisions of this Limited Warranty do not apply to Deliverables that:
(A) are not the proper size for the application; (B) are not installed in accordance with
Company’s published installation instructions; (C) are installed with improper or incorrect
parts and/or are used for purposes for which they are not designed or intended; (D) have
been repaired or altered without the Company’s prior written consent; (E) have been
subjected to misuse, abuse, negligence or accident; (F) have been improperly stored, installed,
maintained or operated; (G) have been used in violation of written instructions provided by
Company to Customer; (H) have been subjected to improper temperature, humidity, or other
environmental conditions, or (I) have been affected by normal wear and tear. In addition,
the provisions of this Limited Warranty do not apply to any defects or issues with the design
or performance of equipment or products not manufactured by Company, nor does it apply
to any code compliance or permit requirements for the assembly, installation, erection or
construction of any goods. Company is not responsible for loss or damage resulting from
use of Deliverables in conjunction with parts or systems not manufactured by Company.
Accessories or products furnished by the Company, but manufactured by others, shall carry
whatever warranty the manufacturers have conveyed to the Company and which can be
passed to Customer.
b. Services. Company warrants that its services will be free from defects in material
and workmanship for a period of 12 months from the date of completion of the particular
items of service. Company’s sole obligation under this service warranty is limited to repair
or reperformance, at its option of the service, provided however, if repair or reperformance
is either impractical or impossible, the Company will refund to Customer that portion of the
price paid to Company for any defective service, provided written notice of the defect or
nonconformance is provided by Customer within 30 days of discovery of the nonconformance.
c. Notification. Customer agrees to immediately notify Company in writing if any claim is
made against Customer for any damages caused by any modules, parts, products, service or
other Deliverables which may be the direct result of any defect in the manufacture of such
aforementioned products. Customer agrees to cooperate with Company and its counsel in
the defense of such claim and Customer agrees not to settle such claim without Company’s
written consent. If Customer fails to notify Company of such claim or fails to cooperate in
such defense as aforesaid, then Company shall be discharged from any obligations under this
Section and shall have no further liability to Customer.
d. Exceptions. The following costs and expenses are not covered by the provisions of these
limited warranties: (i) labor costs for the removal and reinstallation of Deliverables or other
manufacturer’s products; (ii) shipping and freight expenses required to return Deliverables
to Company; (iii) normal maintenance; and (iv) economic losses. In addition, the provisions
of this warranty are not applicable to anything other than defects in Company’s material
(products only) or workmanship.
Hinges & Pivots
factory, provided, however, as set forth herein, Company shall retain a security interest in the
Deliverables until full payment has been made therefore, and Customer agrees, upon request,
to do all things and acts necessary to protect Company’s interest by adequately insuring
the Deliverables against loss or damage from any cause and to have Company named as
an additional insured. Customer will promptly provide Company with a copy of the relevant
certificate of insurance upon Company’s request.
iv
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Terms and Conditions
v
indemnify Indemnitees will continue in full force and effect notwithstanding the termination
or expiration of any order under this Agreement. In any claim against an Indemnitee by an
employee of Customer or any subcontractor or anyone directly or indirectly employed by any
of them or anyone for whose acts they may be liable, the indemnification obligations set
forth in this Section shall not be limited in any way by or for Customer or any subcontractor
under any applicable worker’s compensation act, disability or other employee benefit act.
This provision shall survive termination of any order or Agreement. IN NO EVENT WILL
COMPANY, ITS OFFICERS, DIRECTORS, EMPLOYEES, CUSTOMERS, AFFILIATES,
USERS AND AGENTS, (NOR COMPANY’S SUPPLIERS) BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF
ANY KIND OR NATURE UNDER ANY CIRCUMSTANCES INCLUDING, BUT NOT LIMITED
TO, LOSS OF USE OF THE PRODUCTS, SERVICE INTERRUPTION, LOSS OF PROFITS,
LOSS OF REVENUE, LOSS OF INTEREST, LOST GOODWILL, LOSS OF DATA, WORK
STOPPAGE, IMPAIRMENT OF OTHER GOODS, LOSS BY REASON OF SHUTDOWN
OR NON-OPERATION, INCREASED EXPENSES OF OPERATION, OR CLAIMS OF
CUSTOMER’S CUSTOMERS, OR ANY OTHER LOSSES OR DAMAGES ARISING
OUT OF ANY LACK OR LOSS OF USE OF THE DELIVERABLES WHETHER BASED
ON CONTRACT, WARRANTY, TORT (INCLUDING, BUT NOT LIMITED TO, STRICT
LIABILITY OR NEGLIGENCE), PATENT INFRINGEMENT, OR OTHERWISE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
b)INTELLECTUAL PROPERTY INDEMNITY. Company makes no representation or
warranty to the Customer that the Deliverables shall not infringe any intellectual property
rights including, without limitations, claims arising from patent, copyright, trademark, trade
secret, or other intellectual property infringement. Customer agrees to hold Company
harmless from and defend the Company against any such claim of intellectual property
infringement, including any Damages resulting from that claim, the cost of complying
with any preliminary or permanent injunction, and all other costs of defense (including the
attorneys’ fees and costs), in connection with the foregoing.
c) To the extent that applicable law does not permit any limitations set out in this
Agreement, such limitation shall not be applied or invoked. Nothing in this Agreement will
be interpreted to disclaim liability of Company or the Indemnitees for gross negligence or
willful misconduct. The limitations of remedy and liability herein shall not be interpreted to
affect Company’s obligations, if any, for claims for (i) property damage, (ii) personal injury,
or (iii) wrongful death asserted by persons who are not parties to or beneficiaries of this
Agreement. Further, the limitations of remedy and liability herein shall not be interpreted
to limit Company’s or Customer’s right, if permitted by applicable law, to assert a claim for
contribution among joint tortfeasors in connection with a claim by a person who is not a party
to this Agreement.
21. CERTIFICATIONS. Certification of Deliverables for compliance with UL and ANSI
standards are tested and performed by third-party independent laboratories. Any field
modification or alteration of certified Deliverables will void certification and Company is not
liable to Customer to certify any modified or altered Deliverable.
22. TERM FOR CLAIMS. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS
AGREEMENT BY COMPANY MAY BE BROUGHT BY CUSTOMER MORE THAN ONE (1)
YEAR AFTER THE CAUSE OF ACTION HAS ARISEN.
23. CONSUMER PRODUCTS
WITH RESPECT TO “CONSUMER PRODUCTS” AS DEFINED UNDER THE MAGNUSONMOSS WARRANTY ACT (“MMWA”), THE FOLLOWING STATEMENTS ARE MADE. (A)
SOME STATES OR LOCAL LAWS DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU;
(B) IF ANY IMPLIED WARRANTY IS PROVIDED UNDER THE MMWA, IT IS LIMITED
TO THE DURATION OF THE WARRANTY PROVIDED IN SECTION 18 ABOVE. (C)
SOME STATES OR LOCAL LAWS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU; AND (D) THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE OR LOCATION TO LOCATION.
24. FORCE MAJEURE/EXCUSABLE DELAY. Any delay or failure of Company to perform its
obligations hereunder will be excused to the extent that it is caused by an event or occurrence
beyond Company’s control such as, by way of example and not by way of limitation, acts
of God, acts by any governmental authority (whether valid or invalid), governmental laws
and regulations not presently in effect, fires, floods, windstorms, explosions, riots, natural
disasters, wars, sabotage, accidents, labor problems (including, without limitation, lockouts,
strikes, and slowdowns) at Company’s facility, its source plant or their suppliers, inability
to obtain power, material, labor equipment, or transportation, or court injunction or order.
The delivery date will be extended for a time equal to that of the delay and the schedule for
Company’s performance will be deemed adjusted to that effect.
25. ENTIRE AGREEMENT AND AMENDMENT. This Agreement, together with the
attachments, exhibits, webpages, or supplements specifically referenced and incorporated
herein, constitute the entire agreement between Company and Customer with respect to
the matters contained herein and supersede all previous communications, representations,
or agreements, either oral or written between Company and Customer. No agreement or
understanding varying or expanding this Agreement will be binding upon either party unless it
is in writing and signed by a duly authorized representative of each party hereto.
26. CONFLICTS. In the event of any conflict or inconsistency between the terms of any
agreement, or any part of an agreement or the various documents (including, but not
limited to, electronic documents) between Company and Customer, unless the parties
agree otherwise in writing, the various components of the agreements shall be given the
following precedence (in descending order of precedence): a) any master agreement or long
term agreement between Company and Customer; b) any specific terms, conditions and/
or warranties of the individual products or Deliverables; c) the terms and conditions of this
Agreement, and d) any purchase order.
27. UNSATISFACTORY CREDIT/TERMINATION FOR INSOLVENCY OR DEFAULT.
Customer shall furnish Company with statements evidencing Customer’s financial condition
as Company may, from time to time, reasonably request, and shall notify Company
immediately of any and all events that may have a material adverse effect on Customer’s
business or financial condition. If Company determines, in its sole discretion, that Customer’s
financial condition or creditworthiness is inadequate or unsatisfactory, then in addition to
Company’s other rights, Company may without liability or penalty, take any of the following
actions: (i) modify the payment terms for any outstanding and/or future purchases; (ii) cancel
Ives Architectural hardware products
any previously accepted orders; (iii) delay any further shipment of Deliverables to Customer;
or (iv) any combination of the above.
Company may immediately terminate an order from Customer by giving written notice to
Customer in the event of the happening of any of the following or any other comparable
event: (i) insolvency of the Customer; (ii) filing of a petition in bankruptcy by or against the
Customer; (iii) appointment of a receiver or trustee for the Customer; (iv) execution of an
assignment for the benefit of creditors by the Customer, all of which will allow Company to
demand reclamation of all affected orders; (v) Customer ceases or threatens to cease to
trade; (vi) Company determines that Customer does not meet or no longer meets the credit
requirements of Company or Customer’s credit account is closed; (vii) any Customer violation
of law, specifically including, without limitation, those laws set forth in this Agreement.
In the event of termination in accordance with this section, Company will not be obligated
to accept any existing or additional orders from Customer and Company will be released
from its obligation to deliver under orders accepted prior to such termination. The rejection
or termination of any order by Company will not entitle Customer to any termination or
severance compensation, or to any payment in respect to any goodwill established by
Customer, or render Company liable for damages on account of the loss of prospective
profits, or on account of any loss, expenditure, investment or obligation incurred or made by
Customer.
No action taken under this Section 27 by Company (nor any failure of Company to act under
this Section 27) will constitute a waiver by Company of any of its rights to enforce Customer’s
obligations, including the obligation of Customer to make payments as required under this
Agreement. Upon termination of any order, all amounts owed by Customer to Company will
become immediately due and payable, whether or not otherwise then due or payable.
28. CREDIT RISK ON RESALE OF DELIVERABLES. Customer is responsible for all credit
risks with respect to, and for collecting payment for, all Deliverables sold to third parties
(including End Users, installers, and/or general contractors) whether or not Customer has
made full payment to Company for such Deliverables. The inability of Customer to collect
payment for any Deliverable shall not affect Customer’s obligation to pay Company for any
Deliverable.
29. GOVERNING LAW; VENUE; AND EXPENSES. Any dispute or claim relating to this
Agreement shall be governed by and construed according to the laws of the State of Indiana
(excluding its conflict of laws principles); and not by the provisions of the 1980 United Nations
Convention on the International Sale of Goods. Any disputes or claims shall be instituted
and maintained in the courts of the State of Indiana. Customer consents to the exercise of
jurisdiction over it by such courts and agrees that Indiana is not an inconvenient forum for any
action arising from or relating to this Agreement. Customer agrees to pay for all expenses
(including, but not limited to, collection costs, court costs and attorneys’ fees) incurred by
Company in enforcing the obligations of Customer under this Agreement.
30. RELATIONSHIP OF THE PARTIES. Nothing in this Agreement or any other document
creates an employment, partnership, joint venture, or agency relationship between Company
and Customer, including that of franchisee/franchisor. No party will have any power or
authority to enter into any commitment on behalf of or otherwise bind the any other party
on any matter. No employee of Customer will be deemed to be an employee of Company.
If any provision of this Agreement is deemed to create a franchise relationship or business
opportunity between the Parties, then Company may terminate any purchase order or this
Agreement or the Parties shall negotiate in good faith to modify this Agreement so as to
effect the original intent of the Parties as closely as possible in a mutually acceptable manner
in order that the transactions contemplated hereby are consummated as a reseller agreement
and not a franchise or business opportunity agreement.
31. SETOFF. Customer does not have the right to setoff or to back charge against any
amounts which become payable to Company under this Agreement or otherwise. Company
will not accept responsibility for backcharges for the cost of material or labor by Customer or
any third party.
32. ELECTRONIC COMMUNICATIONS AND ELECTRONIC SIGNATURES. Both parties
expressly agree to electronic transactions and acknowledge that documents they sign
electronically will bind them to the same extent as a paper signature. Customer represents
and warrants to Company that only employees authorized to bind Customer legally shall
electronically sign any document under this Agreement. Customer shall comply with any
method of electronic communication/payment processing specified by Company, including
electronic funds transfer, pay-on-receipt processes/systems, order transmission, releases,
electronic signature, and electronic communication systems, including, without limitation, the
use of electronic data interchange (“EDI”) portals. Notwithstanding the foregoing, e-mails,
even those containing a signature block of one of Company’s representatives, shall not
constitute a signed writing.
33. COMPLIANCE WITH APPLICABLE LAWS.
a. General. Company and Customer will comply with all applicable federal, state and
municipal laws, regulations, codes, ordinances and orders that pertain to the Deliverables,
including but not limited to full compliance with any applicable provisions of The Health
Insurance Portability and Accountability Act. Where the Customer is located outside the
United States, or where the customer intends to ship the product outside the United States,
the Customer shall be responsible for compliance with all U.S. export laws, and for filing all
U.S. Electronic Export Information, as applicable.
b. The Customer acknowledges and agrees that: (i) it shall not violate applicable laws
and regulations in performing its duties under this Agreement; (ii) it does not and shall not
engage in any conduct that shall violate any applicable anti-bribery or anti-corruption laws
or regulations; (iii) it (and its owners, officers, directors, employees and agents) shall not
pay, offer, promise or authorize the payment of, either directly or indirectly, anything of value
(including but not limited to cash, gifts and entertainment) to (a) any government official
or employee of any government; (b) any official or employee of any department, agency, or
instrumentality of a government; (c) any employee of any corporation or entity owned or
controlled by a government; (d) any family member of such officials or employees; (e) any
political party, party official, or political candidate; or (f) any other persons, owners, officers,
directors, employees and agents of any corporation or entity; to improperly or illegally assist
in obtaining or retaining business (including but not limited to any contracts, avoidance
of duties or reduction of tariffs, reduction of taxes or to obtain money owed, or to obtain
regulatory approval) or for the purpose of causing, soliciting or inducing the sale and purchase
of the Deliverables by any party, and (iv) it has full knowledge of and will comply with the
Terms and Conditions
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
D
40. MISCELLANEOUS. (a) This Agreement does not make either party the agent or legal
representative of the other party. Neither party is authorized to create any obligation on behalf
of the other party including, but not limited to, the obligation for payment of any service or
warranty obligation hereunder; (b) The rights and remedies herein reserved to Company are
cumulative and additional to any other rights and remedies provided at law or equity; (c) The
official text of this Agreement is in the English language. If this Agreement is translated into
another language, the English text will govern any question with respect to interpretation; (d)
The headings in this Agreement are for convenience of reference only and do not affect the
meaning of this Agreement in any manner.
Latches, Catches & Bolts
39. NO IMPLIED WAIVER. The failure of either party at any time to require performance by
the other party of any provision of this Agreement will in no way affect the right to require
such performance at any time thereafter, nor will the waiver of either party of a breach of any
provision of this Agreement constitute a waiver of any succeeding breach of the same or any
other provision.
C
38. SEVERABILITY. If any provision of this Agreement is held to be invalid, illegal, or
unenforceable under any statute, regulation, ordinance, executive order, or other rule of law,
that provision will be deemed severed to the extent necessary to comply with such statute,
regulation, ordinance, order, or rule. In the event such provision is deemed severed, the parties
will negotiate in good faith to arrive at an alternative arrangement approximating the original
business objective of the parties. The remaining terms and conditions of this Agreement will
remain in effect.
Flush Bolts & Coordinators
37. ASSIGNMENT. Customer may not assign this Agreement without the prior written
consent of Company. Company may assign its rights and delegate its duties under this
Agreement, without the prior consent of Customer, to an Affiliate, or to a third party in the
event of a spin-off, merger, business combination, consolidation or sale of all, or substantially
all, of its assets or business that are related to this Agreement. The rights and duties in this
Agreement shall bind and inure to the benefit of any such assignee.
B
36. NOTICES AND CHANGE OF ADDRESS. All notices or other communications under this
Agreement shall be in writing and delivered in person, or sent by receipted courier, express
mail, e-mail, or postage prepaid certified or registered mail, addressed to the party for whom it
is intended, at the addresses set forth in this Agreement. Either party may change its address
for notice by giving written notice to the other party. Any notice or other communication shall
be deemed given no later than the date actually received. Notice by courier, express mail,
certified mail, or registered mail shall be deemed given on the date it is officially recorded as
delivered and, in the absence of such record of delivery, it shall be rebuttably presumed to
have been delivered on the third Business Day after it was deposited. Notices sent by e-mail
require tangible confirmation of receipt from addressee.
Pulls & Plates
35. NO THIRD-PARTY BENEFICIARY. Each party is entering into this Agreement solely
based on the representations contained herein for its own purposes and not for the benefit of
any third party.
A
34. REPRESENTATIONS AND WARRANTIES. Customer represents, warrants and
covenants to Company that: (a) it has the right, power, and authority to enter into this
Agreement and fully perform its obligations hereunder; (b) it has all necessary rights in and
to its respective Content and Marks for use within the scope of this Agreement, including
the licenses granted herein; and (c) it complies, and at all times shall comply, with all laws,
rules, and regulations in effect that are applicable to its performance under this Agreement,
including obtaining all such approvals and/or permits as may be required hereunder.
DEFINITIONS.
Capitalized terms have the meanings set forth in this Section, or in the Section in which they
first appear in this Agreement.
“Agreement” means these Allegion Terms and Conditions of Sale and Service, together with
any applicable Country Supplement or Region Supplement provided by Company, and all of
the documents referenced herein or therein.
“Affiliate” means any Person that directly or indirectly, through one or more intermediaries,
controls, is controlled by, or is under common control with, the Company. The term “control”
(including the terms “controlled by” and “under common control with”) means the possession,
directly or indirectly, of the power to direct or cause the direction of the management and
policies of a Person, whether through the ownership of voting securities, by contract or
otherwise.
“Business Day” means any day except Saturday, Sunday or any other day on which
commercial banks located in the United States are authorized or required by Law to be closed
for business.
“Company” means Schlage Lock Company, LLC or any subsidiary or affiliate thereof selling
products that are part of the Allegion product portfolio. Schlage Lock Company and/or its
subsidiary or affiliates will be severally but not jointly liable under the Agreement.
“Company Marks” refers to the Marks of Company.
“Confidential Information” shall mean any and all information provided by either party
to the other party pertaining to the disclosing party’s business. Confidential Information
shall include, but not be limited to, any bitting lists, formulae for products, manufacturing
processes, production techniques, packaging processes, methods, research materials, ideas,
marketing plans and related materials, quality standards, test results and data, apparatus,
engineering drawings, contract documents, computer software, hardware, or firmware,
business activities information such as financial information, reports, projections, books
and records, customer and supplier information, and operations, customer and supplier lists
and data, specifications, know how, and other Proprietary Information or Trade Secrets (as
defined herein) that either party may furnish to the other party. Confidential Information
shall not include information that: (a) is or becomes publicly known if such public knowledge
or disclosure is not the result of any act or failure to act on the part of the receiving party;
(b) is, at the time of disclosure, already known to the Receiving Party without utilizing the
Confidential Information; (c) is information disclosed to the Receiving Party by a third party
which is not to the Receiving Party’s knowledge, after inquiry of the third party, under a duty
of confidentiality to the Disclosing Party; or (d) is independently developed by the Receiving
Party without the use of Confidential Information. The Receiving Party shall have the burden
of proof as to prior knowledge and absence of breach. Confidential Information may be
furnished in any tangible or intangible form including, but not limited to, writings, drawings,
computer and other electronic media, logic diagrams, component specifications, graphs,
prototypes, samples, or verbal communications and regardless of whether such information
is marked or designated as “confidential.” For the avoidance of doubt, all information,
knowledge or data disclosed by Company to Customer, regardless of whether disclosed in
written, tangible, oral, visual or other form, including, without limitation, sample products,
equipment, software, or other objects or material, provided by Company to Customer, and all
information, knowledge or data which was obtained by Customer from visits to Company’s
facilities, shall be considered “Confidential Information” under this Agreement.
“Content” means all information (including without limitation any text, music, sound,
photographs, video, graphics, data or software), in any medium, on a particular Company Web
page or Website or in Marketing Materials.
“Customer” means the purchaser of Deliverables from Company.
“Deliverables” means any good or service or both purchased by Customer from Company
under these General Terms and Conditions of Sale and Service.
“End Users” means the purchaser that (a) has acquired a Deliverable from Customer for (i)
its own and its Affiliate’s/Affiliates’ internal use and not for resale, remarketing or distribution
or (ii) incorporation into its own products and (b) is an individual or entity, other than any
federal, state or local agency, office or division.
“IP” means all intellectual property and industrial property rights comprising or relating to/
of the following: (a) Patents; (b) Trademarks; (c) internet domain names, whether or not
Trademarks, registered by any authorized private registrar or Governmental Authority, web
addresses, web pages, website and URLs; (d) works of authorship, expressions, designs and
design registrations, whether or not copyrightable, including copyrights and copyrightable
works, software and firmware, application programming interfaces, architecture, files, records,
schematics, data, data files, and databases and other specifications and documentation; (e)
Trade Secrets; and (f) all other intellectual property and industrial property rights, and all
rights, interests and protections that are associated with, equivalent or similar to, or required
for the exercise of, any of the foregoing, however arising, in each case whether registered or
unregistered and including all registrations and applications for, and renewals or extensions of,
such rights or forms of protection pursuant to the Laws of any jurisdiction throughout in any
part of the world.
“Marketing Materials” means all marketing brochures, buckslips, pamphlets, emails, text,
call scripts or other material, whether in printed format, audio or audiovisual format, or in
any other format, that contain any (i) Content relating to the Company Deliverables or (ii)
Company Marks.
“Marks” means collectively the domain names, trademarks, trade names, service marks,
trade dress, logos, and the like used or provided by either party for use in connection with this
Agreement.
“Patents” means all patents (including all reissues, divisionals, provisionals, continuations
and continuations-in-part, re-examinations, renewals, substitutions and extensions thereof),
patent applications, and other patent rights and any other Governmental Authority-issued
indicia of invention ownership (including inventor’s certificates, petty patents and patent
utility models).
“Person” means a person or entity.
“Price Books” mean Company’s current Price Book in effect for the applicable Deliverable
being purchased by Customer.
“Trade Secrets” means and includes business or technical information of either party,
including processes, formulas, devices, techniques, compilations and other material that
a party attempts to maintain in secret and that derive commercial value for such party
from not being generally known to the public or readily ascertainable through independent
development or reverse engineering.
Hinges & Pivots
Company’s Code of Conduct for Business Partners as set forth on the Allegion customer
website, WHICH IS HEREBY INCORPORATED BY REFERENCE.
c. The Customer shall indemnify and hold the Company harmless from any claim, demand,
expense or cost arising from any breach of this Article.
d. The Customer shall permit the Company to conduct an audit or review of the Customer’s
financial books and records and business operations at such other times that the Company
considers it necessary to confirm compliance with this provision. Such audit may be conducted
by representatives of the Company or, at the Company’s sole discretion, by a certified public
accounting firm selected by the Company. The Customer shall cooperate with any inquiries
from the Company’s Ethics & Compliance Group.
e. A violation of this provision constitutes a material breach of this Agreement and the
Company may terminate any purchase order or this Agreement immediately, with no
opportunity to cure, in accordance with Section 27 of this Agreement.
f. Notwithstanding the foregoing provisions of this Section 33, (i) Company is not responsible
for obtaining or maintaining any permits for the performance of services or the verification
or compliance with any code requirements relative to the performance of services, (ii) to the
extent any sale of Deliverables pursuant to this Agreement may require approval of the U.S.
Government, Company’s obligations under this Agreement are conditioned upon the grant of
such approval and upon compliance by Customer with any restrictions imposed by the U.S.
Government in connection with such approval, and (iii) in the event the Deliverables are to
be used in a nuclear facility, the Customer shall, prior to such use, arrange for insurance or
governmental indemnity protecting Company against liability. The Customer hereby releases
and agrees to indemnify Company and its suppliers for any nuclear damage including, but not
limited to, loss of use, in any manner arising out of the nuclear incident, whether alleged to be
due, in whole or in part by Company or its suppliers.
g. No Inducements. Each party represents to each other that neither it nor any person
acting on its behalf has, in contravention of any applicable law, given or offered to give or will
give or offer to give, any sum of money or other material consideration to any person, directly
or indirectly, as an inducement to obtain business hereunder or to influence the granting
of licenses or other governmental permissions to enter into this Agreement or perform
obligations hereunder.
h. Equal Employment Opportunity. Company is a U.S. federal contractor that complies with
Executive Order 11246, as amended, and applicable regulations in 41 CFR Parts 60-1 through
60-60, 29 U.S.C. § 793 and applicable regulations in 41 CFR § 60-741; and 38 U.S.C. § 4212 and
applicable regulations in 41 CFR Part 60-250 and 60-300. THE FOLLOWING PROVISIONS
ARE INCORPORATED HEREIN BY REFERENCE: Executive Order 11246 and 41 CFR §
60-4.3(a); Executive Order 11701 and 41 CFR §§ 60-250.5(a), 60-300.5; Executive Order 11758
and 41 CFR § 60-741.5(a); U.S. immigration laws, including the L-1 Visa Reform Act of 2004
and the H-1B Visa Reform Act of 2004; and Executive Order 13496.
i. Ethical Business Conduct. Customer shall adopt and comply with Company’s Business
Partner Code of Conduct which is EXPRESSLY INCORPORATED HEREIN BY REFERENCE.
vi
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Index by Product Description
vii
A
G
Angle Stop. . . . . . . . . . . . . . . . . . . . . . . . . D11
Automatic Flush Bolt. . . . . . . C2, C3, C4
Automatic Wall Holder. . . . . . . . . . . E15
Auxiliary Pusher . . . . . . . . . . . . . . . . . . D12
Gravity Coordinator. . . . . . . . . . . . . . . C14
H
Pocket Sliding Door Bolt. . . . . . . . . . G15
Protection Plates. . . . . . . . . . . . . . . . . B13
Pull Plate . . . . . . . . . . . . . . . . . . . . . B7, B8
Pull Plate (less pull). . . . . . . . . . . . . . . B6
Push Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . B8
Push Bar with Pull. . . . . . . . . . . . . . . . . B9
Push Plate. . . . . . . . . . . . . . . . . . . . . . . . . B6
Carry Bar. . . . . . . . . . . . . . . . . . . . . . . . . . C14
Casement Adjuster. . . . . . . . . . . . . . . . G8
Casement Fastener. . . . . . . . . . . . G7, G8
Ceiling Hook . . . . . . . . . . . . . . . . . . . . . . . G4
Chain Door Guard. . . . . . . . . . . . . . . . . . D7
Chest Handle. . . . . . . . . . . . . . . . . . . . . G12
Closet Pole Socket. . . . . . . . . . . . . . . . . G6
Coat & Hat Hook. . . . . . . . . . . . . . . G3, G4
Constant Latching Flush Bolt. . . . . . C5
Coordinator, Bar. . . . . . . . . . . . . . . . . . C12
Coordinator, Filler Bar . . . . . . . . . . . . C12
Coordinator, Mounting Bracket. . . C13
Crash Stop. . . . . . . . . . . . . . . . . . . . . . . . F10
Handrail Bracket. . . . . . . . . . . . . . . . . . . G2
Hasp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
Hinge Pin Stop. . . . . . . . . . . . . . . E21, E22
Hinge, 3 Knuckle,
Full Mortise. . . . . . . . . . . . . . . . . . . . A5, A6
Hinge, 5 Knuckle,
Full Mortise. . . . . . . . . . . . A6, A7, A8, A9
Hinge, 5 Knuckle, Half Surface. . . . A10
Hinge, Continuous
Pin & Barrel Full Mortise. . . . . . . . . A28
Hinge, Continuous Geared
Full Surface. . . . . . . . . . . . . . . . . A19, A20
Hinge, Continuous Geared
Half Surface . . . . . . . . . . . . . . . . . A21, A22
Hinge, Continuous Pin & Barrel
Full Mortise, Full Wrap. . . . . . A29, A30
Hinge, Continuous Pin & Barrel
Swing Clear. . . . . . . . . . . . . . . . . . . . . . A29
Hinge, Electrifies. . . . . . . . . . . . . . . . . . . A11
Hinge, Pocket. . . . . . . . . . . . . . . . . . . . . A52
Hinge, Residential . . . . . . . . . . . . . . . . A12
Hobbyist Barrel Bolt. . . . . . . . . . . . . . . G9
Holder, Kick Down. . . . . . . . . . . . E16, E17
Hook and Hasp. . . . . . . . . . . . . . . . . . . . G11
Hook and Staple. . . . . . . . . . . . . . . . . . . G9
D
I
Decorative Corner. . . . . . . . . . . . . . . . . . G11
Decorative Hasp. . . . . . . . . . . . . . . . . . G10
Decorative Hinge . . . . . . . . . . . . . . . . . G10
Door Base Stop, Residential. E20, E21
Door Bolt, Dutch. . . . . . . . . . . . . . . . . . . D6
Door Bolt, Mortise . . . . . . . . . . . . . . . . . D6
Door Guard, Chain . . . . . . . . . . . . . . . . . D7
Door Guard, Solid Bar. . . . . . . . . . . . . . D7
Door Knocker. . . . . . . . . . . . . . . . . . . . . . F7
Door Numbers. . . . . . . . . . . . . . . . . . . . . F9
Door Pull. . . . . . . . . . . . . . . B2, B3, B4, B5
Door Pull, Offset. . . . . . . . . . . . . . . . . . . B5
Door Silencer. . . . . . . . . . . . . . . . . . . . . E23
Draw Catch. . . . . . . . . . . . . . . . . . . . . . . G12
Dust Proof Strike . . . . . . . . . . . . . . . . . . C11
Dutch Door Bolt. . . . . . . . . . . . . . . . . . . . D6
Invisible Latch. . . . . . . . . . . . . . . . . . . . D12
Vandal Resistant Trim. . . B10, B11, B12
Viewer, One Way . . . . . . . . . . . . . . F5, F6
K
W
B
Ball Catch. . . . . . . . . . . . . . . . . . . . D13, D16
Ball Catch, Adjustable. . . . . . . . . . . . D16
Ball Catch, Dual Adjustable. . . . . . . D16
Bar Coordinator. . . . . . . . . . . . . . . . . . . C12
Bar Window Lift . . . . . . . . . . . . . . . . . . . G7
Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
Broad Butt Hinge. . . . . . . . . . . . . . . . . . G9
C
Kick Down Holder. . . . . . . . . . . . . E16, E17
Knocker, Door. . . . . . . . . . . . . . . . . . . . . . F7
L
Letter Box Plate. . . . . . . . . . . . . . . . . . . F8
Letter Box Sleeve. . . . . . . . . . . . . . . . . . F8
Lock Guard. . . . . . . . . . . . . . . . . . F2, F3, F4
Long Pulls . . . . . . . . . . . . . . . . . . . . . . . . . B6
M
Elbow Catch. . . . . . . . . . . . . . . . . . . . . . G13
Magnetic Catch. . . . . . . . . . . . . . . . . . . D14
Manual Flush Bolt. C6, C7, C8, C9, C10
Manual Wall Holder . . . . . . . . . . E9, E14
Middle Butt Hinge . . . . . . . . . . . . . . . . . G9
Mortise Door Bolt. . . . . . . . . . . . . . . . . . D6
Mounting Brackets . . . . . . . . . . . . . . . C13
F
N
Filler Bar. . . . . . . . . . . . . . . . . . . . . . . . . . C12
Finger Pull. . . . . . . . . . . . . . . . . . . . . . . . G13
Flexible Door Stop, Residential.E20, E21
Floor Stop . . . . . . . . . . . . . . E2, E3, E4, E5
Floor Stop & Automatic Holder.E6, E8
Floor Stop & Manual Holder. . . . . . . E7
Floor Stop & Semi-automatic Holder.E6
Flush Bolt, Automatic . . . . . . C2, C3, C4
Flush Bolt, Constant Latching. . . . . C5
Flush Bolt, Manual.C6, C7, C8, C9, C10
Flush Pull. . . . . . . . . . . . . . . . . . . . G13, G14
Friction Lid Support. . . . . . . . . . . . . . . . G11
Numbers, Door. . . . . . . . . . . . . . . . . . . . . F9
E
Ives Architectural hardware products
P
Pivot, 1/2" Offset . . . . . . . . . . . A43, A44
Pivot, 3/4" Offset
A36, A37, A38,
A39, A40,
A41, A42
Pivot, Center Hung
A45, A46,
A47, A48
Pivot, Intermediate. . . . . . . . . A49, A50
Pivot, Intermediate, Electrified. . . A51
Pivot, Pocket . . . . . . . . . . . . . . . . . . . . . A52
R
Riser . . . . . . . . . . . . . . . . . . . . . . . . . . . E2, E4
Roller Bumper . . . . . . . . . . . . . . . . . . . . E19
Roller Catch. . . . . . . . . . . . . . . . . . . . . . . D15
Roller Latch. . . . . . . . . . . . . . . D8, D9, D10
S
Screen Door Pull. . . . . . . . . . . . . . . . . . F10
Side Window Lock. . . . . . . . . . . . . . . . . G7
Slide Door Edge Pull. . . . . . . . . . . . . . G15
Sliding Door Pull. . . . . . . . . . . . . . . . . . G16
Solid Bar Door Guard . . . . . . . . . . . . . . D7
Stop, Crash . . . . . . . . . . . . . . . . . . . . . . . F10
Stop, Hinge Pin. . . . . . . . . . . . . . E21, E22
Strike Plate. . . . . . . . . . . . . . . . . . . . . . . D10
Strike, Dust Proof. . . . . . . . . . . . . . . . . . C11
Storm Door Latch. . . . . . . . . . . . . . . . . . F9
Support Hinge. . . . . . . . . . . . . . . . . . . . . G11
Surface Bolt . . . . . . . . . . . . . . . . . . . D2, D3
Surface Bolt, Decorative. . . . . . . D4, D5
V
Wall Bumper. . . . . . . . . . . . . . . . . . E11, E12
Wall Holder, Automatic . . . . . . . . . . E15
Wall Holder, Manual. . . . . . . . . . E9, E14
Wall Stop. . . . . . . . . . . . . . . . E9, E10, E14
Wardrobe Hook. . . . . . . . . . . . . . . . . . . . G5
Window Lock. . . . . . . . . . . . . . . . . . . . . . G6
Numerical Part Index
B
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
E
Stops
7226, 7226F. . . . . . . . . . . . . . . . . . . . . . . A37
7227, 7227F. . . . . . . . . . . . . . . . . . . . . . A38
7230F. . . . . . . . . . . . . . . . . . . . . . . . . . . . A39
7230F-7237F INT . . . . . . . . . . . . . . . . A48
7237F. . . . . . . . . . . . . . . . . . . . . . . . . . . . A40
7244F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A41
7244F-7245F INT. . . . . . . . . . . . . . . . A48
7245F. . . . . . . . . . . . . . . . . . . . . . . . . . . . A42
7253 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A43
7255 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A44
7255J . . . . . . . . . . . . . . . . . . . . . . . . . . . . A44
7256. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A45
7259. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A46
8102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2
8103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2
8103EZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3
8105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3
8111-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B4
8112-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B4
8121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5
8190. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5
8200. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
8300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
8302. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8303. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8311. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8
8400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13
8402. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13
9011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9041. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9042. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9070. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9071. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9072. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8
9103EZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B9
9110. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9190. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B9
9210 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9220. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9264. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
9265. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
9266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
9267. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
9311. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9320. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9321. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9330. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9340. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
91105F. . . . . . . . . . . . . . . . . . . . . . . . . . . A50
91105F-PT. . . . . . . . . . . . . . . . . . . . . . . A50
Pulls & Plates
F
Exterior Hardware
G
Miscellaneous Hardware
FS448 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
WS449 . . . . . . . . . . . . . . . . . . . . . . . . . . . E14
FS450 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E7
FS452. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
SB453 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2
FS455. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
FB457. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C9
FB458 . . . . . . . . . . . . . . . . . . . . . . . . . . . . C10
FB458 . . . . . . . . . . . . . . . . . . . . . . . . . . . . C10
RB470. . . . . . . . . . . . . . . . . . . . . . . . . . . . E19
RB471. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19
RB472. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19
481. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
482. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
FS495 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8
FS496 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8
FS497. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8
FS544. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E17
FS555. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E17
571. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
572. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
574. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
575. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
580. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
581. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G5
582 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G5
585 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
586. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
600, 700. . . . . . . . . . . . . . . . . . . . . . . . . . A27
601. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
602, 702. . . . . . . . . . . . . . . . . . . . . . . . . . A27
611, 711. . . . . . . . . . . . . . . . . . . . . . . . . . . . A28
620. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
STK685. . . . . . . . . . . . . . . . . . . . . . . . . . . D10
STK685L . . . . . . . . . . . . . . . . . . . . . . . . . D10
U696 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5
698. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5
U698 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5
700. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A27
700. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6
U700. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6
701. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6
U701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6
702 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A27
705 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A28
711. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A28
715. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A29
VR810-DT. . . . . . . . . . . . . . . . . . . . . . . . . B10
VR810-NL. . . . . . . . . . . . . . . . . . . . . . . . . B10
VR814-DT. . . . . . . . . . . . . . . . . . . . . . . . . B10
VR814-NL. . . . . . . . . . . . . . . . . . . . . . . . . B10
AS895. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D11
VR900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . B11
VR900LLP. . . . . . . . . . . . . . . . . . . . . . . . . B11
VR910-DT. . . . . . . . . . . . . . . . . . . . . . . . . B12
VR910M-DT. . . . . . . . . . . . . . . . . . . . . . . B12
VR910M-NL. . . . . . . . . . . . . . . . . . . . . . . B12
VR910-NL. . . . . . . . . . . . . . . . . . . . . . . . . B12
980. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
990. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G16
991. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G16
1010. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
1011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
1012. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
1020. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
1021. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
RL1152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
FS1153 . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18
FS1154 . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18
SB1600. . . . . . . . . . . . . . . . . . . . . . . . . . . . D3
SB1601M1. . . . . . . . . . . . . . . . . . . . . . . . . . D3
SB1601M2. . . . . . . . . . . . . . . . . . . . . . . . . . D3
02-3107, . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
02/25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7
7212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A34
7212-7212V-7222 INT. . . . . . . . . . . . . . A47
7212V . . . . . . . . . . . . . . . . . . . . . . . . . . . . A34
7215, 7215F. . . . . . . . . . . . . . . . . . . . . . . . A35
7215-7226-7227 INT. . . . . . . . . . . . . . . A47
7215F-7226F-7227F INT. . . . . . . . . . . A47
7215PT-7226PT-7227PT . . . . . . . . A49
7222 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A36
A
WS45X . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
046HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . A19
S48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D6
FB51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C4
COR52. . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
FB52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C4
053HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . A22
FB53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C4
054,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D6
054HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . A22
59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
059,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
060, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
COR60. . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
061,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
FB61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C5
FB62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C5
63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
SR64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23
SR65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23
WS65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E10
66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G8
066. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
SR66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23
69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G8
72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
COR72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
112HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A21
CS115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
157HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A21
159. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
210HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A22
218. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
221. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
222. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
223. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
224HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . A22
227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
253. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D5
261. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C6
262 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C6
265 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C7
325. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
326 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
327. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
330 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
335. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
336 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
345 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
347. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
349. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
FB358. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C8
SB360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2
WS401. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E11
WS402 . . . . . . . . . . . . . . . . . . . . . . . . . . . . E11
WS404CVX. . . . . . . . . . . . . . . . . . . . . . . . E11
405. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
WS406. . . . . . . . . . . . . . . . . . . . . . . . . . . E12
WS407. . . . . . . . . . . . . . . . . . . . . . . . . . . . E12
411R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E13
430. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS434. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
R435. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS436. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
R437. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS438. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS441 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
WS443. . . . . . . . . . . . . . . . . . . . . . . . . . . . E14
FS444 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
WS445. . . . . . . . . . . . . . . . . . . . . . . . . . . .E14
FS446 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E7
WS447. . . . . . . . . . . . . . . . . . . . . . . . . . . . E14
Hinges & Pivots
CB1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C14
DP1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C11
LG1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2
MB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB1F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB1V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
DP2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C11
MB2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB2F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB2V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
3CB1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5
3CB1HW. . . . . . . . . . . . . . . . . . . . . . . . . . . A6
3PB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5
3SP1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A6
MB1F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB3F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB3V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
5BB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7
5BB1HW . . . . . . . . . . . . . . . . . . . . . . . . . . . A8
5BB1SC. . . . . . . . . . . . . . . . . . . . . . . . . . . A10
5BB1SCHW. . . . . . . . . . . . . . . . . . . . . . . A10
5BB1WT. . . . . . . . . . . . . . . . . . . . . . . . . . . . A8
5BB4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A9
5BB4HW. . . . . . . . . . . . . . . . . . . . . . . . . . . A9
5PB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7
07,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
COR7G. . . . . . . . . . . . . . . . . . . . . . . . . . . . C14
LB7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2
FS9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
COR9G. . . . . . . . . . . . . . . . . . . . . . . . . . . . C14
LG10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2
CL11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
LG11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3
WS11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
WS11X. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
CL12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
LG12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3
FS13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
LG13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
CL14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
LG14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
R14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
FS17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
AS18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D11
FS18L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
FS18S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
FL20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
WS20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
WS20X . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
CL21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
CL21A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
CL22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
026. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
026,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
2 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
RL30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D8
FB31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C2
COR32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
FB32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C2
FL32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
RL32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D8
FB33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C2
WS33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E10
WS33X. . . . . . . . . . . . . . . . . . . . . . . . . . . . E10
RL36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
RL38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D4
FS40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
WS40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
FB41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C3
FS41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
COR42. . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
FB42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C3
FS42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
FS43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
FL44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
045HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . A19
WS45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
Ives Architectural hardware products
viii
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Finishes
ix
BHMA US
Description
609
US5
Satin Brass Plated, Blackened, Satin Relieved, Clear Coated
628
US28
Satin Aluminum, Clear Coated
666
US3
Bright Brass Plated, Clear Coated
666
US3AL
Bright Brass Plated, Clear Coated
667
US4
Satin Brass Plated, Clear Coated
668
US10A
Satin Bronze Plated, Clear Coated
668
US10AL Satin Bronze Plated, Clear Coated
669
US14
Bright Nickel Plated 670
US15
Satin Nickel Plate
673
US92
Aluminum, Clear Coated
689
US65
Aluminum Painted
702
US26D Satin Chrome Plated
703
US10B
Oxidized Satin Bronze Plated, Oil Rubbed
710
313AN
Dark Bronze Anodized
711
315AN
Black Anodizes
713 US26D
716
A10B
Satin Bronze Plated, Clear Coated
BLK
Black Epoxy Coated
W
White Epoxy Coated
T
Tan Epoxy Coated
BRN
Brown Epoxy Coated
CLR
Clear Expoxy Coated
US5
Satin Brass Plated, Blackened, Satin Relieved, Clear Coated
A5Aluminum
AP
Aluminum, Prime Paint
R
Red Epoxy Coated
US26D Satin Chrome Plated
690
US69
Dark Bronze Painted
605
US3
Bright Brass, Clear Coated
606
US4
Satin Brass, Clear Coated
689
SP28
Aluminum Painted
691
SP10
Light Bronze Painted
693
SPBLK
Black Painted
695
SP313
Dark Bronze Painted
706SP4 Brass
716
Satin Bronze Plated, Clear Coated
P600
P600
Primed for Paint BRNBrown
GRYGray
TANTan
White
White Rubber
618
US14
Bright Nickel Plated, Clear Coated
619
US15
Satin Nickel Plated, Clear Coated
620
US15A
Satin Nickel Plated, Blackened, Satin Relieved, Clear Coated
622
US19
Flat Black Coated
625
US26
Polished Chrome Plated
626
US26D Satin Chrome Plated
612
US10
Satin Bronze, Clear Coated
Ives Architectural hardware products
Base Material
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Aluminum
Any
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass
Brass, Bronze
Brass, Bronze
Brass, Bronze
Brass, Bronze
Brass, Bronze
Brass, Bronze
Bronze
Finishes
Base Material
Bronze
Plastic
Plastic
Plastic
Plastic
Plastic
Rubber
Rubber
Rubber
Rubber
Rubber
Stainless Steel 300
Stainless Steel 300
Stainless Steel 400
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Zinc/Brass
A
Hinges & Pivots
B
Pulls & Plates
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
E
Stops
BHMA US
Description
613
US10B
Dark Oxidized Satin Bronze, Oil Rubbed Finish
White
White
BLK
Black Plastic
BRN
Brown Plastic
CLR
Clear Plastic
P
Plastic
A3Rubber
RRubber
Brown
Brown Rubber
Tan
Tan Rubber
Gray
Gray Rubber
629
US32
Polished Stainless Steel
630
US32D
Satin Stainless Steel
654
US32D
Satin Stainless Steel
600
USP
Primed for Paint - Steel
600
FP
Primed for Paint - Steel
603
2G
Zinc Plated
603
2C
Zinc Plated
604
2G
Zinc Plated/Dichromate Sealed
632
US3
Bright Brass Plated, Clear Coated
638
US5
Satin Brass Plated, Blackened, Satin Relieved, Clear Coated
639
US10
Satin Bronze Plated, Clear Coated
640
US10B
Dark Oxidized Satin Bronze, Oil Rubbed Finish
645
US24
Bright Nickel Plated, Clear Coated
646
US15
Satin Nickel Plated, Clear Coated
652
US26D Satin Chrome Plated
689
SP28
Aluminum Painted
693
SPBLK
Black Painted
695
SP313
Dark Bronze Painted
695
SP313
Dark Bronze Painted
706SP4 Brass
716
Satin Bronze Plated, Clear Coated
716 F10B
A5Steel
406
Exterior Hardware
Antimicrobial Coating (AM) inhibits the growth of bacteria, available on many Ives Architectural Hardware Products.
F
G
Miscellaneous Hardware
Ives Architectural hardware products
x
A
Hinges & Pivots
Packaging, Handing
Packaging Key
Many Ives items are available in a variety of packaging forms designated by a prefix. The Ives Price Book
contains the specific packaging options for each Ives product. Below is a description of these options.
B
Pulls & Plates
Symbol
Description of Package
CCarded
CGC
Commercial Grade Carded
SC
Schlage Branded Carded
SPS
Schlage Branded Slim-Pak
Door Handing
LH
INSIDERH
Left Hand
Right Hand
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
SPSlim-Pak
OUTSIDE
INSIDE
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
LRBRRB
Left Hand
Right Hand
Reverse Bevel
OUTSIDE
Reverse Bevel
xi
Ives Architectural hardware products
Architectural Hinges, Continuous Hinges and Pivots
A1
Hinges & Pivots
Table Of Contents
D
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A31
Latches, Catches & Bolts
Pivots
C
Continuous Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A13
Flush Bolts & Coordinators
Residential Hinges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A12
B
3PB1 3 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5
3CB1 3 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5
3CB1HW 3 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A6
3SP1 3 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A6
5PB1
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7
5BB1
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7
5BB1HW
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A8
5BB1WT
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A8
5BB4
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A9
5BB4HW
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A9
5BB1SC
5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10
5BB1SCHW 5 Knuckle, Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A10
Electrified Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A11
Pulls & Plates
Architectural Hinges
page
General Hinge Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2
How to Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
ANSI Hinge Identification Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
A1
General Hinge Information
SELECTION OF THE PROPER WEIGHT AND BEARING TYPE
Standard Weight . . . . . Plain Bearing
Standard Weight . . . . . Ball Bearing, Concealed Bearing
Heavy Weight. . . . . . . . . Ball Bearing, Concealed Bearing
Considerations to determine Weight and Bearing type:
- Weight of Door
- Frequency of use
- Frame
- Door Hardware
Always use ball bearing or concealed bearing hinges for doors with door
closers and in all fire rated openings. Heavy weight doors and high frequency doors should use heavy weight ball bearing or concealed bearing
hinges.
GUIDELINES FOR HINGE METAL
- Interior door or non-corrosive area use: Plated or painted Steel
- Interior labeled door use: Plated or Painted Steel, Stainless Steel
- Interior door in corrosive area use: Stainless Steel , Brass, Bronze
- Exterior doors use: Stainless Steel, Brass, Bronze
Standard pin material are Brass Hinge – Steel Pin,
Stainless Steel Hinge – Stainless Steel Pin, Steel Hinge – Steel Pin
GUIDELINES FOR FREQUENCY OF DOOR USAGE:
Build Type
Daily Usage Hinge Type
High Frequency/ Heavy Weight Door
Large Department Store Entrance 5,000
Heavy Weight
Hospital Corridor and Surgical Doors 5,000
Heavy Weight
Large Office Building Entrance
4,000
Heavy Weight
School Entrance
1,250
Heavy Weight
School Toilet Door
1,250
Heavy Weight
Office Stairwell
500
Heavy Weight
Office Building Toilet Door
400
Heavy Weight
Medium Frequency/ Medium Weight Door
School Corridor Door
100
Standard Weight
Hospital Consultation Rooms
100
Standard Weight
Office Building Corridor Door
80
Standard Weight
Store Toilet Door
60
Standard Weight
Storage Room
50
Standard Weight
Low Frequency /Light Door
Residential Entrance
30
Plain Bearing
Interior Residential
20
Plain Bearing
A2
Considerations to determine Hinge size
- Door Width
- Door Thickness
- Weight
- Clearance
GUIDELINES FOR HINGE HEIGHT
OOR THICKNESS
D
IN INCHES
1-3/8”
1-3/8
1-3/4
1-3/4
1-3/4
2” - 2-1/2”
2” - 2-1/2”
DOOR WIDTH
IN INCHES
Up to 32”
32” to 37”
Up to 36”
36” to 48”
Over 48”
Up to 42”
Over 42”
Grade 1:
Grade 2:
Grade 3:
2,500,000Heavy Weight Ball & Concealed Bearing
1,500,000 Standard Weight Ball & Concealed Bearing
350,000 Light Weight Plain Bearing
DOOR THICKNESS
CLEARANCE NEEDED
HINGE OPEN WIDTH
1-3/8
3/4
4
1-3/4
1
4
1-3/4
1-1/2
4-1/2
1-3/4
2
5
1-3/4
3
6
2
1
4-1/2
2
1-1/2
5
2
2-1/2
6
2-1/4
1
5
2-1/4
2
6
2-1/2
3/4
5
2-1/2
1-3/4
6
3
3/4
8
3
2-3/4
8
*Distance needed between wall and door at 180º to allow for any projections
from wall; trim, decorative molding, etc.
GUIDELINES FOR NUMBER OF HINGES
- Doors under 7'6" . . . . . . . . . 3 hinges
- Doors over 7'6". . . . . . . . . . . 4 hinges
LOCATION OF HINGES
Top hinge 5" from jamb
rabbet to top of barrel
5"
(127mm)
Equal
Bottom hinge 10" from
bottom edge of barrel to
finished floor
Third hinge centered
between top and bottom
hinges
10"
(254mm)
Ives Architectural hardware products
HINGE HEIGHT
IN INCHES
3-1/2
4”
4-1/2”
5”
6”
5” heavy weight
6” heavy weight
Clearance Requirement*
ANSI/BHMA Grade/Minimum Cycle requirements
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A2
Hinges & Pivots
Architectural Hinges, Continuous Hinges and Pivots
Note: Some western
states use a standard 7"
from top and 11" from the
bottom
Architectural Hinges, Continuous Hinges and Pivots
5
-
BB
-
1
-
HW - 4.5x4.5 - 652
-
NRP
B
Pulls & Plates
Number of Knuckles:
3 - 3 Knuckle
5 - 5 Knuckle
Type:
1
2
3
4
Full Mortise
Half Mortise
Full Surface
Half Surface
C
Plain Bearing
Ball Bearing
Concealed Bearing
Spring Hinge
Flush Bolts & Coordinators
Function:
PB
BB
CB
SP
D
5x6
5x7
Latches, Catches & Bolts
Weight/Options:
Blank Standard Weight
HW
Heavy Weight
SC
Swing Clear
SH
Security Stud
WT
Wide Throw
HT
Hospital Tip
RC Round Corners, 1/4" or 5/8" Radius
Size Examples:
4.5 x 5
3.5 x 3.5
4.5 x 6
4 x 4
5 x 4.5
4.5 x 4
5x5
4.5 x 4.5
A3
How to Order:
Hinges & Pivots
Ives Hinge Number System
Please note: For availability of specific models, please refer to the item’s catalog page or consult Customer Service.
Larger sizes, up to 6 x 8 are available. Consult factory.
E
Stops
Finish (Some models require extended lead times):
600
USP - Steel
605
US3 - Brass
606
US4 - Brass
612
US10 - Brass
613
US10B - Brass
619
US15 - Brass
625
US26 - Brass
626
US26D - Brass
630
US32D - Stainless
632
US3 - Steel
633
US4 - Steel
639 US10 - Steel
640
US10B - Steel
641 US10A - Steel
643 US11 - Steel
646
US15 - Steel
651 US26 - Steel
652 US26D - Steel
F
Exterior Hardware
Miscellaneous Hardware
G
Special Pins Applications:
NRP
Non-Removable Pin
TW4
Four Wire
TW8
Eight Wire
MONMonitor
TW4M Four Wire with Monitor
TW8M Eight Wire with Monitor
Ives Architectural hardware products
A3
A4
Hinges & Pivots
Architectural Hinges
ANSI Hinge Identification Reference
Second number indicates product type
1 – Full mortise
2 – Half mortise
3 – Full surface
4 – Half surface
5 – Anchor, pivot reinforced or thrust pivot unit or hinge sets
6 – Olive knuckle hinges
7 – Pivot hinge
8 – Rescue hardware
E
Stops
D
Latches, Catches & Bolts
C
B
Pulls & Plates
First number indicates material
1 – Cast, forged or extruded brass or bronze
2 – Wrought brass or bronze
5 – Stainless steel
8 – Wrought or forged steel, or malleable iron
Flush Bolts & Coordinators
A = ANSI
Third number indicates function
1 – Anti-friction bearing
2 – Anti-friction bearing, swing clear
3 – Plain bearing
4 – 4 to 0, special conditions
Fourth number indicates grade
1 – Grade 1, 4BB Extra Heavy Duty
2 – Grade 2, 2BB Standard Duty
3 – Grade 3, Plain Bearing
G
Miscellaneous Hardware
F
Exterior Hardware
Example:
A8111 – Steel, Full Mortise, Anti-friction, Grade 1
A5112 – Stainless, Full Mortise, Anti Friction Bearing, Grade 2
A4
Ives Architectural hardware products
Architectural Hinges
• For standard weight doors
• Low frequency usage
• Packed with wood and metal screws
Not for use with a door closer.
D
E
Stops
F
Exterior Hardware
US10
US10B US10A
US11
US15
US26 US26D
US3
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
US26D
652
G
Miscellaneous Hardware
BHMA
US4
605606 612 613 614 616 619 625 626
Finishes steel
Ives Finish
USP
Latches, Catches & Bolts
BHMA
3 Knuckle, Concealed Bearing Full Mortise Hinge
• For standard weight doors
• Medium frequency usage
• Packed with wood and metal screws
Options
• NRP, Non-Removable Pin
• SH, Security stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Dimensions
Size (Inches) Size (mm) Gauge
3.5 x 3.5
90 x 90
0.134
4 x 4
102 x 102 0.134
4.5 x 4
114 x 102
0.134
4.5 x 4.5
114 x 114
0.134
5 x 4.5
127 x 114
0.134
Meets ANSI/BHMA A156.1
A8112 – Steel
A5112 – Stainless Steel
A2112 – Brass
Finishes brass
Ives Finish
US3 Gauge
0.134
0.134
0.134
0.134
0.134
C
3CB1
Size (mm)
90 x 90
102 x 102 114 x 102
114 x 114
127 x 114
Flush Bolts & Coordinators
Dimensions
Size (Inches)
3.5 x 3.5
4 x 4
4.5 x 4
4.5 x 4.5
5 x 4.5
B
Meets ANSI/BHMA A156.1
A8133 – Steel
A5133 – Stainless Steel
A2133 – Brass
Pulls & Plates
Options
• NRP, Non-Removable Pin
• SH, Security Stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fasteners - Pin-in-Socket
A5
3 Knuckle, Plain Bearing Full Mortise Hinge
Hinges & Pivots
3PB1
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
629630
Ives Architectural hardware products
A5
A6
Hinges & Pivots
Architectural Hinges
3CB1HW 3 Knuckle, Concealed Bearing Full Mortise Hinge
Dimensions
Size (Inches)
4.5 x 4
4.5 x 4.5
5 x 4.5
5 x 5
Meets ANSI/BHMA A156.1
A8112 – Steel
A5112 – Stainless Steel
A2112 – Brass
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
• For heavy weight doors
• High frequency usage
• Packed with wood and metal screws
Options
• NRP, Non-Removable Pin
• SH, Security stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
D
UL listed for use with fire rated doors
E
Stops
F
Exterior Hardware
3SP1
3 Knuckle Spring Full Mortise Hinge
• For automatic closing of doors
• Packed with wood and metal screws
Dimensions
Size (Inches)
4 x 4
4.5 x 4
4.5 x 4.5 Finishes brass
Ives Finish
US3 BHMA
US3
US10B US10A
Gauge
0.134
0.134
0.134
US11
US15
US26 US26D
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
US10
Size (mm)
102 x 102
114 x 102
114 x 114
605606 612 613 614 616 619 625 626
Finishes steel
Ives Finish
USP
BHMA
US4
G
Miscellaneous Hardware
Gauge
0.180
0.180
0.190
0.190
Options
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.7
K81071F – Steel
K51071F – Stainless Steel
A6
Size (mm)
114 x 102
114 x 114
127 x 114
127 x 127
629630
Ives Architectural hardware products
US26D
652
Architectural Hinges
• For standard weight doors
• Low frequency usage
• Packed with wood and metal screws
Not for use with a door closer.
C
Latches, Catches & Bolts
5 Knuckle, Ball Bearing Full Mortise Hinge
E
Size (Inches) Size (mm)
5 x 4.5
127 x 114
5 x 5
127 x 127
Gauge
0.146
0.146
F
Exterior Hardware
Gauge
0.130
0.130
0.134
0.134
Stops
Size (mm)
80 x 102
102 x 102
114 x 102
114 x 114
D
Dimensions
Size (Inches)
3.5 x 3.5
4 x 4
4.5 x 4
4.5 x 4.5 US4
US10
US10B US10A
US11
US15
US26 US26D
605606 612 613 614 616 619 625 626
US3
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
US26D
652
G
Miscellaneous Hardware
Finishes steel
Ives Finish
USP
BHMA
Gauge
0.123
0.134
0.134
0.134
0.134
• For standard weight doors
• Medium frequency usage
• 2 ball bearing
• Packed with wood and metal screws
Options
• NRP, Non-Removable Pin
• SH, Security Stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.1
A8112 – Steel
A5112 – Stainless Steel
A2112 – Brass
BHMA
Flush Bolts & Coordinators
5BB1
Size (mm)
89 x 89
102 x 102
114 x 102
114 x 114
127 x 114
B
Dimensions
Size (Inches)
3.5 x 3.5
4 x 4
4.5 x 4
4.5 x 4.5 5 x 4.5
Pulls & Plates
Options
• NRP, Non-Removable Pin
• SH, Security Stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.1
A8133 – Steel
A5133 – Stainless Steel
A2133 – Brass
Finishes brass
Ives Finish
US3 A7
5 Knuckle, Plain Bearing Full Mortise Hinge
Hinges & Pivots
5PB1
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
629630
Ives Architectural hardware products
A7
Architectural Hinges
A8
Hinges & Pivots
5BB1HW
B
Pulls & Plates
• For heavy weight doors
• High frequency usage
• 4 ball bearing
• Packed with wood and metal screws
Options
• NRP, Non-Removable Pin
• SH, Security Stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.1
A8111 – Steel
A5111 – Stainless Steel
A2111 – Brass
Dimensions
Size (Inches) Size (mm)
4.5 x 4
114 x 102
4.5 x 4.5
114 x 114
Gauge
0.180
0.180
Size (Inches) Size (mm)
5 x 4.5
127 x 114
5 x 5
127 x 127
5BB1WT
Meets ANSI/BHMA A156.1
A8111 – Steel
BHMA
US3
A8
US10B US10A
Gauge
0.134
0.134
0.146
0.146
0.146
US11
US15
US26 US26D
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
US10
Size (mm)
114 x 127
114 x 152
127 x 152
127 x 178
127 x 203
605606 612 613 614 616 619 625 626
Finishes steel
Ives Finish
USP
BHMA
US4
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
Dimensions
Size (Inches)
4.5 x 5
4.5 x 6
5 x 6
5 x 7
5 x 8
Finishes brass
Ives Finish
US3 5 Knuckle, Ball Bearing, Wide Throw
Full Mortise Hinge
• For medium weight doors
• Medium frequency usage
• 2 ball bearing
• Packed with wood and metal screws
Options
• NRP, Non-Removable Pin
• SH, Security Stud
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
5 Knuckle, Ball Bearing, Heavy Weight
Full Mortise Hinge
629630
Ives Architectural hardware products
US26D
652
Gauge
0.190
0.190
Architectural Hinges
•
•
•
•
For standard weight doors
Medium frequency usage
2 ball bearing
Packed with through bolts, grommets and sheet metal screws
B
Meets ANSI/BHMA A156.1
A8412 – Steel
Pulls & Plates
Options
• NRP, Non-Removable Pin
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
A9
5 Knuckle, Ball Bearing, Half Surface Hinge
Hinges & Pivots
5BB4
C
Flush Bolts & Coordinators
Dimensions
Size (Inches) Size (mm) Gauge
4.5 1140.134
5BB4HW 5 Knuckle, Ball Bearing, Half Surface
Heavy Weight Hinge
•
•
•
•
For heavy weight doors
High frequency usage
4 ball bearing
Packed with through bolts, grommets and sheet metal screws
D
Options
• NRP, Non-Removable Pin
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.1
A8411 – Steel
F
Exterior Hardware
US4
US10
US10B US10A
US11
US15
US26 US26D
605606 612 613 614 616 619 625 626
US3
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
US26D
652
G
Miscellaneous Hardware
Finishes steel
Ives Finish
USP
BHMA
E
BHMA
Stops
Dimensions
Size (Inches) Size (mm) Gauge
4.5 1140.180
Finishes brass
Ives Finish
US3 Latches, Catches & Bolts
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
629630
Ives Architectural hardware products
A9
A10
Hinges & Pivots
Architectural Hinges
5BB1SC
5 Knuckle, Ball Bearing, Swing Clear
Full Mortise Hinge
•
•
•
•
•
For standard weight doors
Square edge standard
Medium frequency usage
2 ball bearing
Packed with flat head wood and metal screws
Options
• NRP, Non-Removable Pin
• B, beveled edge door
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
Meets ANSI/BHMA A156.1
A8122 – Steel
A5122 – Stainless Steel
A2122 – Brass
Flush Bolts & Coordinators
B
Pulls & Plates
Designed to completely clear the opening when door is opened 92 degrees.
C
Dimensions
Size (Inches) Size (mm)
Gauge
4.5 1140.134
5 1270.145
Latches, Catches & Bolts
5BB1SCHW 5 Knuckle, Ball Bearing, Swing Clear
Heavy Weight Full Mortise Hinge
D
Options
• NRP, Non-Removable Pin
• B, beveled edge door
• HT, Hospital Tip
• RC, Round Corners - 1/4" or 5/8" Radius
• SEC, Security Fastners - Pin-in-Socket
E
Stops
F
Exterior Hardware
Dimensions
Size (Inches) Size (mm) Gauge
4.5 1140.180
5 1270.190
Finishes brass
Ives Finish
US3 BHMA
US3
US10B US10A
US11
US15
US26 US26D
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
US10
605606 612 613 614 616 619 625 626
Finishes steel
Ives Finish
USP
BHMA
US4
G
Miscellaneous Hardware
For heavy weight doors
High frequency usage
2 ball bearing
Packed with flat head wood and metal screws
Designed to completely clear the opening when door is opened 92 degrees.
Meets ANSI/BHMA A156.1
A8121 – Steel
A10
•
•
•
•
629630
Ives Architectural hardware products
US26D
652
Architectural Hinges
US11
US15
C
US10B US10A
US26 US26D
605606 612 613 614 616 619 625 626
US3
US4
US10
US10B US10A
US11
US15
US26
600632 633639640641 643646 651
US26D
652
D
Finishes stainless steel
Ives Finish
US32 US32D
BHMA
Latches, Catches & Bolts
Finishes steel
Ives Finish
USP
BHMA
US10
Flush Bolts & Coordinators
BHMA
US4
B
Finishes brass
Ives Finish
US3 Through-Wire is rated for 50 volts AC/DC at 3.5 amp continuous and 16 amp pulse,
maximum pulse 400 mili second.
Monitor rated 30VDC at .5 amp
Special wire configurations available, contact factory.
Pulls & Plates
UL Listed - UL634
Meets ANSI/BHMA A156.1
A8111 – Steel
A5111 – Stainless Steel
A2111 – Brass
- Through Wire - TW4 (4 wires) & TW8 (8 wires)
- Monitor – MON
- Through Wire with Monitor – TW4M & TW8M
Available in 3 and 5 Knuckle
One hinge per box, packed with wood and machine screws
Hinge is NRP as a standard
High quality brass ferrules and plastic tubing protect the wires
Through-wire hinges cycle tested to ensure durability
Ives warranty applies - 12 months from date of shipment
A11
•
•
•
•
•
•
Hinges & Pivots
Electrified Hinge
Available Options
629630
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
A11
1000 Series Residential Hinges
•
•
•
Full mortise hinges in 2 sizes: 3-1/2" and 4".
Two corner options: Square corners and 5/8" or 1/4"
radius corners.
Substrates include: Steel.
1010
Schlage Carded Only
1011
Model
Size Corner
1010
1011
1012
1020
1021
3-1/2" x 3-1/2"
3-1/2" x 3-1/2"
3-1/2" x 3-1/2"
4" x 4"
4" x 4"
Square Corner
5/8" Radius Corner
1/4" Radius Corner
Square Corner
5/8" Radius Corner
C
Flush Bolts & Coordinators
B
Pulls & Plates
A12
Hinges & Pivots
Architectural Hinges
1020
Schlage Carded Only
Schlage Carded Only
Latches, Catches & Bolts
1012
BHMA
632646 651
D
* not available on 1012 hinge
* only available on 1011
1021
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
Schlage Carded Only
A12
Finishes steel
Ives Finish
F605E F609E F619E F620E* F625E** F716E
Ives Architectural hardware products
Continuous Hinges
D
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
Latches, Catches & Bolts
Pin and Barrel Hinges
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A24
Electrified Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A24
How to Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A25
Door Sizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A26
600, 700. . . . . . . . . . . . . . . . . Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A27
602, 702 . . . . . . . . . . . . . . . . . Full Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A27
611, 711. . . . . . . . . . . . . . . . . . . . Swing Clear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A28
705. . . . . . . . . . . . . . . . . . . . . . . Full Mortise, Full Wrap. . . . . . . . . . . . . . . . . . . . . . A28
715 . . . . . . . . . . . . . . . . . . . . . . . Full Mortise, Full Wrap. . . . . . . . . . . . . . . . . . . . . . A29
Electrical Cutouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A30
C
Aluminum Geared Hinges
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A16
Electrified Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A16
How to Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A17
Door Sizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A18
045HD . . . . . . . . . . . . . . . . . . . Half Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A19
046HD. . . . . . . . . . . . . . . . . . . Half Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A19
053HD . . . . . . . . . . . . . . . . . . . Half Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A20
054HD . . . . . . . . . . . . . . . . . . . Half Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A20
112HD. . . . . . . . . . . . . . . . . . . . . Full Mortise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A21
157XY . . . . . . . . . . . . . . . . . . . . Full Surface, Center Pivot. . . . . . . . . . . . . . . . . . . A21
210HD. . . . . . . . . . . . . . . . . . . . Full Surface, Swing Clear . . . . . . . . . . . . . . . . . . . A22
224HD. . . . . . . . . . . . . . . . . . . . Full Mortise, Edge Protector . . . . . . . . . . . . . . . . A23
Electrical Cutouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A23
Flush Bolts & Coordinators
page
Continuous Hinge Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A14
Cross Reference Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A15
B
Continuous Hinge Table Of Contents
Pulls & Plates
Continuous hinges are available in two styles; aluminum geared
and pin and barrel in steel or stainless steel.
A13
The design of a continuous hinge eliminates the gap between the
door and the frame. The absence of gap also helps prevents finger
from being pinched, making it a safer device than traditional hinges.
These benefits result in higher efficiency and less maintenance,
maximizing the value of your opening investment.
Hinges & Pivots
Ives Continuous Hinges are designed to last the life of the building.
The unique design distributes the weight of the door along the entire
length of the frame, reducing the high amount of stress normally
associated at top of door and frame on butt hinge applications. Not
only does this reduce hinge failure, it also keeps your door in constant
alignment, eliminating the chance of door sag. These characteristics
make continuous hinges suitable for high use/high traffic doors.
A13
A14
Hinges & Pivots
Continuous Hinges
Aluminum Geared
B
Pulls & Plates
Geared continuous hinges utilize a single gear section for the leaf and
a separate gear section for the frame side of the door. The two are
held in place together by a full length cover channel and rotate on a
series of bearings.
Flush Bolts & Coordinators
I ve s 6 1 1 , 7 1 1
1-3/8”
GA 0.075” Hi n ge
T h i ck n es s
3/8”
C
I ve s 5 0 0 , 6 0 0 , 7 0 0
1/4”
1-9/16”
1/2”
1-3/4”
Latches, Catches & Bolts
3/8”
Pin and Barrel
1/8”
GA 0.075” Hi n ge T h i ck n es s
2-1/4 ”
3/4”
1-3/4”
5/32”
E
Stops
D
Pin and Barrel hinges share many of the same characteristics of a
traditional hinge. Both have a center pin and rolled knuckles.
However, a continuous
Pin and Barrel hinge stretches along the
1/16”
entire length of the
frame. IVES offers both stainless steel and
1/4 ”
primed steel to best match your specific application.
1 3/8" [34.9]
HINGE
5/16"
[7.9]
1/2"
[12.7]
3/4"
[19.1]
GA. 0.060"
[1.5]
[44.5]
GA. 0.075" HINGE THICKNESS
1 3/4"
1/4"
[6.4]
9/16" 1/2"
[14.3] [12.7]
DOOR
1/8"
[9.5]
1/2"
3/8"
[9.5]
[12.7]
HINGE
1/2"
[12.7]
GA. 0.060"
[1.5]
1 1/16"
3/4"
[19.1]
3/4"
[19.1]
2 3/16"
Lifetime Warranty Ives continuous hinges carry a limited lifetime warranty, ensuring your opening will function to your satisfaction every time.
FRAME
Ives Architectural hardware products
[1.3]
GA. 0.050"
1/16"
7/32" [5.6] HINGE ALLOWANCE
[1.6]
2" [50.8]
G
A14
5/8"
[15.9]
Miscellaneous Hardware
[55.5]
GA 0.075" HINGE THICKNESS
[44.5]
F
FRAME
0.750"
[19.0]
GA. 0.050"
[1.3]
Exterior Hardware
2" [50.8]
5/32" [4.0] HINGE ALLOWANCE
DOOR
Continuous Hinges
A15
Hinges & Pivots
Cross Reference Guide
Ives
Hager
Markar
McKinney
Pemko
Select
Stanley
780-112HD
MCK-12HD
FMSLFHD
SL11HD
661HD
B
Geared
045HD780-045HD
046HD780-046HD
053HD780-053HD
054HD
780-054HD
780-210HD
MCK-22HD
FSHD
SL21HD
665HD
224HD
780-224HD
MCK-25HD
FMHD
SL24HD
662HD
157XY*
780-157HD
MCK-58HD
FSCPHD
SL57HD
664HD
157HD
780-157HD
MCK-58HD
FSCPHD
SL57HD
664HD
D
Pin and Barrel
Latches, Catches & Bolts
210HD
C
Flush Bolts & Coordinators
112HD
Pulls & Plates
600
FM200
SL200
602
FS202
611
N/A
700
790-900
FM300
SL300
702
FS302
SL302
705
790-905
HG305
SL305
652
711
790-911
HG311
SL311
656
715
790-915
HG315
653
651
E
Stops
F
Exterior Hardware
*Application only. Features and benefits exceed current market standard.
G
Miscellaneous Hardware
Ives Architectural hardware products
A15
A16
Hinges & Pivots
Continuous Hinges
Aluminum Geared Hinges
General Information
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
Material
6063-T6 Aluminum
Standard Lengths
83", 85", 95", 120"
Custom lengths are available up to 120", consult factory.
Finishes
CL - US28 (628) Clear Anodized
BR - 313AN (710) Dark Bronze
Hinge Duty
All Ives Aluminum Geared Hinges are Heavy Duty (HD).
Amount of bearings varies by size:
83" – 32 Bearings
85" – 32 Bearings
95" – 36 Bearings
120"- 47 Bearings
Door Weight
Each hinge can hold a door up to 450 lbs (Rivet nuts recommended)
and a max door width of 4'0".
ANSI Certified
All Ives Aluminum Geared Hinges excluding the 157XY are certified to ANSI 156.26, Grade 1
UL Listed
All Ives Aluminum Geared Hinges excluding the 157XY are tested and approved UL 10C (90 minutes).
Field Modifications:
All Ives Aluminum Geared Continuous Hinges can be cut to length during installation. The unique
mounting pattern allows to cut up to 6" from bottom while still having double row fasteners. If cut
more than 13.5", other modifications may be necessary.
Electrification Options
Electric Power Transfer (EPT)
Electric power transfer provides a means of transferring power from the door frame to the edge of a
swinging door. Ives Continuous Hinges provide standard cut outs to fit Von Duprin EPT-2, EPT-10 and
PNT-1 devices. Consult factory for other electrical cut out options.
Electrical Through-Wire (TW)
Provides electric power transfer from the frame to the door in order to supply power to an electrified
mortise or cylindrical locks, exit devices with electric latch retraction, and/or electric strikes (pairs of
doors). Through-wire is rated 50 volts AC/DC at 3.5 amp continuous and 16 amp pulse. Maximum pulse
400 milliseconds. Ives thru-wire hinges are fully compatible with 4 wire and 8 wire installations.
G
Miscellaneous Hardware
F
Exterior Hardware
Only available for the full mortise hinges
A16
Ives Architectural hardware products
Continuous Hinges
Hinges & Pivots
A17
Aluminum Geared Hinges
How to Order:
112HD
CL
-
83
-
EPT
B
Pulls & Plates
Half Surface
Half Surface
Half Surface
Half Surface
Full Mortise
Full Surface - Center Pivot
Full Surface - Center Pivot
Full Surface - Swing Clear
Full Mortise - Edge Protector
C
Flush Bolts & Coordinators
Model
045HD
046HD
053HD
054HD
112HD
157XY
157HD
210HD
224HD
-
D
Latches, Catches & Bolts
Finish
CLClear
BRBronze
Custom finishes available, consult factory
Length
83"
* 85"
95"
120"
Other lengths available up to 120", consult factory. Handing required.
E
Stops
Electric Power Transfer Prep
Electric Through Wire
Security Fasteners - Pin-in-Socket
Wood Fasteners
Thread forming screws (pilot hole required)
Hospital Tip
Through Wire Panel
F
Exterior Hardware
Options
**EPT
**TW8
*SEC
WD
TF
HT
TWP
* Not available with 157XY Continuous Hinge
** Full Mortise Models Only
G
Miscellaneous Hardware
Ives Architectural hardware products
A17
Aluminum Geared Hinges - Clearance Requirements
Hinge
Side
Clearance
1/8”
Hinge
Side
Clearance
3/16”
Hinge
Side
Clearance
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A18
Hinges & Pivots
Continuous Hinges
1/32”
Frame
Irregularity
1/16”
Frame
Irregularity
SINGLE DOOR
Door Under-Sizing
Hinge-Side Lock-Side
Frame Beveled Door Square
Beveled
Model
Clearance ClearanceIrregularity Clearance Edged
Edged
045HD5/32" 1/8" 1/32" 1/32"5/16"11/32"
046HD5/32" 1/8" 1/32" 1/32"5/16"11/32"
053HD5/32" 1/8" 1/32" 1/32"5/16"11/32"
054HD5/32" 1/8" 1/32" 1/32"5/16"11/32"
112HD 5/16" 1/8"1/32"1/32"
15/32"1/2"
224HD5/16" 1/8"1/32"1/32"
15/32"1/2"
210HD 1/16" 1/8"1/32"1/32"7/32"1/4"
157XY 1/16" 1/8"1/32"1/32"7/32"1/4"
G
Miscellaneous Hardware
F
Exterior Hardware
PAIR OF DOORS
Door Under-Sizing
A18
Square Square BeveledBeveled
Hinge-Side Lock-Side
Frame Beveled Door Edged
Edged
Edged
Edged
Model
Clearance Clearance Irregularity Clearance
Total
Each Door
Total
Each Door
045HD5/32"3/16"1/16" 1/16"9/16"9/32" 5/8" 5/16"
046HD5/32" 3/16"1/16" 1/16"9/16"9/32" 5/8" 5/16"
053HD5/32"3/16"1/16" 1/16"9/16"9/32" 5/8" 5/16"
054HD5/32"3/16"1/16" 1/16"9/16"9/32" 5/8" 5/16"
112HD 5/16" 3/16"1/16" 1/16"7/8" 7/16" 15/16"15/32"
224HD 5/16" 3/16"1/16" 1/16"7/8" 7/16" 15/16"15/32"
210HD 1/16" 3/16"1/16" 1/16"3/8" 3/16" 7/16"7/32"
157XY 1/16" 3/16"1/16" 1/16"3/8" 3/16" 7/16"7/32"
Templates and installation instructions available on line at www.allegion.com/us
Ives Architectural hardware products
Continuous Hinges
•
•
•
•
A19
Hinges & Pivots
045HD Half Surface Continuous Hinge
Half surface for retrofit or new construction
Handing required when modified
Frame leaf depth 1-9/16"
9/32" door inset
B
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 x 1/2" steel self tapping screw
1/4-20 x 1-1/2" AL Sex Bolt
1/4-20 x 1" Steel Shoulder Bolt
12-24 x 3/4" Steel Self Drilling Shoulder Bolt
Optional SEC-Security Fasteners available
1-9/32"
C
Custom Anodizing and Painting are
available, consult factory.
Flush Bolts & Coordinators
3-1/16"
Finishes
Clear (CL), Dark Bronze (DB)
2-9/32"
1-9/16"
Latches, Catches & Bolts
D
5/32" Clearance for Square Edge Door
3/16" Clearance For Beveled Edge Door
046HD Half Surface Continuous Hinge
•
•
•
•
Half surface for retrofit or new construction
Handing required when modified
Frame leaf depth 1-15/16"
9/32" door inset
1-9/32"
2-5/8"
1-15/16"
G
Miscellaneous Hardware
Custom Anodizing and Painting are
available, consult factory.
F
Finishes
Clear (CL), Dark Bronze (DB)
3-1/16"
Exterior Hardware
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 x 1/2" steel self tapping screw
1/4-20 x 1-1/2" AL Sex Bolt
1/4-20 x 1" Steel Shoulder Bolt
12-24 x 3/4" Steel Self Drilling Shoulder Bolt
Optional SEC-Security Fasteners available
E
Stops
5/32" Clearance for Square Edge Door
3/16" Clearance For Beveled Edge Door
Ives Architectural hardware products
A19
A20
Hinges & Pivots
Continuous Hinges
053HD
Half Surface Continuous Hinge
•
•
•
•
Half surface for retrofit or new construction
Handing required when modified
Frame leaf depth 1-9/16"
1/8" door inset
Flush Bolts & Coordinators
B
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 x 1/2" steel self tapping screw
1/4-20 x 1-1/2" AL Sex Bolt
1/4-20 x 1" Steel Shoulder Bolt
12-24 x 3/4" Steel Self Drilling Shoulder Bolt
Optional SEC-Security Fasteners available
Finishes
Clear (CL), Dark Bronze (DB)
C
Custom Anodizing and Painting are
available, consult factory.
2-1/8"
1-5/32"
2-9/32"
Latches, Catches & Bolts
1-9/16"
D
5/32" Clearance for Square Edge Door
3/16" Clearance For Beveled Edge Door
054HD Half Surface Continuous Hinge
E
Stops
•
•
•
•
Half surface for retrofit or new construction
Handing required when modified
Frame leaf depth 1-15/16"
1/8" door inset
F
Exterior Hardware
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 x 1/2" steel self tapping screw
1/4-20 x 1-1/2" AL Sex Bolt
1/4-20 x 1" Steel Shoulder Bolt
12-24 x 3/4" Steel Self Drilling Shoulder Bolt
Optional SEC-Security Fasteners available
2-1/8"
1-5/32"
Finishes
Clear (CL), Dark Bronze (DB)
2-5/8"
1-15/16"
G
Miscellaneous Hardware
Custom Anodizing and Painting are
available, consult factory.
A20
5/32" Clearance for Square Edge Door
3/16" Clearance For Beveled Edge Door
Ives Architectural hardware products
Continuous Hinges
• Non Handed
• Flush Mounted, No Inset
• 48" Maximum Door Width
• Beveled or Square Edge Doors
For Doors Weighing up to 450 pounds without reinforcing,
600 pounds with reinforcing
A21
Full Mortise Aluminum Geared Continuous Hinge
Hinges & Pivots
112HD
Pulls & Plates
B
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 X 3/4" Steel Self Drilling, Self Tapping Screws
Optional WD - Wood Screws or SEC - Security Fasteners Available
Flush Bolts & Coordinators
Finishes
Clear (CL), Dark Bronze (DB)
Custom Anodizing and Painting are
available, consult factory.
C
D
•
•
•
•
•
•
•
Non Handed
Narrow Frame
1/16" Door Inset
48" Maximum Door Width
Beveled or Square Edge Doors
A patented easy-to-install, heavy duty, full surface continuous hinge
Lateral and vertical adjustability while the door is still hanging
E
Full Surface, Center Pivot
Aluminum Geared Continuous Hinge
Stops
157XY
Latches, Catches & Bolts
5/16" Clearance for Square Edge Door
1/32" Clearance For Beveled Edge Door
For Doors Weighing up to 550 pounds
Allow 1/8" for
cover moldings
F
3-3/16"
Exterior Hardware
Standard lengths 83", 95", 119"
Standard Mounting Hardware
12-24 X 1/2" Steel Self Drilling
and Tapping Screws,
Optional Wood Screws and
Min. frame
Security Fasteners Available
width
Custom Paint Finish Available
Max. door
opening
7/8"
G
Miscellaneous Hardware
Finishes
Clear (CL), Dark Bronze (DB)
1-5/8"
1-1/4"
Ives Architectural hardware products
A21
A22
Hinges & Pivots
Continuous Hinges
210HD
Full Surface, Swing Clear
Aluminum Geared Continuous Hinge
•
•
•
•
For Doors Weighing up to 600 pounds
Flush Bolts & Coordinators
B
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 X 1/2" Steel Self Tapping Screws,
1/4-20 X 1-1/2" AL Sex Bolt
1/4-20 X 1" Steel
Shoulder Bolt, 12-24 X 3/4" Steel Self Drilling,
Optional SEC - Security Fasteners Available
Finishes
Clear (CL), Dark Bronze (DB)
Latches, Catches & Bolts
C
Custom Anodizing and Painting are
available, consult factory.
F
Exterior Hardware
E
Stops
D
1/16" Clearance for Square Edge Door
3/32" Clearance For Beveled Edge Door
G
Miscellaneous Hardware
A22
Handing required when modified
1/32" Door Inset
48" Maximum Door Width
Beveled or Square Edge Doors
Ives Architectural hardware products
Continuous Hinges
•
•
•
•
•
Handing required when modified
Door Edge Protector
48" Maximum Door Width
1/16" Door Inset
Beveled or Square Edge Doors
A23
Full Mortise Aluminum Geared Continuous Hinge
Hinges & Pivots
224HD
For Doors Weighing up to 450 pounds without reinforcing,
600 pounds with reinforcing
B
Flush Bolts & Coordinators
Finishes
Clear (CL), Dark Bronze (DB)
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
12-24 X 3/4" Steel Self Drilling, Self Tapping Screws
Optional WD - Wood Screws or SEC - Security Fasteners Available
Custom Anodizing and Painting are
available, consult factory.
C
EPT
112HD
EPT
224HD
Because clearances may vary between door and frame
manufacturer, and locations can be influenced by the door
hardware it is always recommend contacting Ives Customer
Technical for specific template information.
For your general information below are standard locations
for Von Duprin EPT2 or EPT10, and monitor switch.
F
“C
TW”
“C
TW”
LL TW”
L “C
When ordering indicate the following:
1. Opening size.
2. Handing. LH, RH, RHR or LHR.
3. Manufacturer and model number of the electrical product
being used. Example; Von Duprin EPT2
Exterior Hardware
“C
EPT”
“C
EPT”
LL EPT”
L “C
TopTop
of of
Top
of
hinge/door
hinge/door
hinge/door
E
“C
EPT”
“C
EPT”
LL EPT”
L “C
TopTop
of of
Top
of
hinge/door
hinge/door
hinge/door
Stops
TopTop
of of
Top
of
hinge/door
hinge/door
hinge/door
Ives Aluminum Geared Continuous Hinges are available with
factory modified cutouts to accommodate most electrical
frame to door requirements. Special templates are required.
TW
TW
TW
TW
112HD
112HD
112HD
112HD
224HD
224HD
224HD
224HD
224HD
224HD
224HD
112HD
112HD
112HD
D
Electrical Cutouts
Latches, Catches & Bolts
5/16" Clearance for Square Edge Door
1/32" Clearance For Beveled Edge Door
From Top Edge of Door to Center Line of Cut-Out
TWP option centered in hinge.
Ives Architectural hardware products
G
Note: See ordering guide in price book for proper placement.
Miscellaneous Hardware
Standard112HD 224HD 112HD/224HD
Length
EPTEPTTW
83" 30"30"41-1/2"
85" 32"32"42-1/2"
95" 42"42"57-3/4"
120" 67"67"81-25/32"
A23
A24
Hinges & Pivots
Continuous Hinges
Pin and Barrel Hinges
Standard Lengths
83", 85", 95", 120"
Custom lengths are available up to 120", consult factory.
Finishes
US32D (630) Satin Stainless Steel
USP (600) Steel, Primed for Paint
Barrel Type
Twin Self Lubricated Nylon Bearings with Stainless Steel Pin.
Door Weight
Each hinge can hold a door up to 600 lbs (Rivet nuts recommended) and a max door width of 4'0".
ANSI Certified
All Ives Pin and Barrel Hinges certified to ANSI 156.26, Grade 1.
UL Listed
All Ives Steel and Stainless Steel Pin and Barrel Hinges are tested and approved UL 10C (3 hr).
Field Modifications
All Ives Pin and Barrel Continuous Hinges can be cut to length during installation. If more than 6" from
bottom of hinge, additional modifications may be necessary.
Electrification Options
Only available for the Full Mortise Hinges
Electric Power Transfer (EPT)
Electric power transfer provides a means of transferring power from the door frame to the edge of a
swinging door. Ives Continuous Hinges provide cut outs to fit Von Duprin EPT-2, EPT-10 and
PNT-1 devices. Consult factory for other EPT cut out options.
Electrical Through-Wire (TW)
Provides electric power transfer from the frame to the door in order to supply power to an electrified
mortise or cylindrical locks, exit devices with electric latch retraction, and/or electric strikes (pairs of
doors). Through-wire is rated for 3.5 amp continuous and 16 amp pulse. Ives thru-wire are fully
compatible with 4 wire and 8 wire installations.
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
General Information
A24
Ives Architectural hardware products
Continuous Hinges
A25
Hinges & Pivots
Pin and Barrel Hinges
-
US32D
-
83
-
EPT
Latches, Catches & Bolts
Steel
600
602
611
C
Flush Bolts & Coordinators
Model
Stainless Steel
700
Full Mortise
702
Full Surface - Center Pivot
705
Full Mortise - Full Wrap
711
Full Surface - Swing Clear
715
Full Mortise - Half Wrap
Full Mortise
Full Surface - Center Pivot
Full Surface - Swing Clear
D
Finish
Stainless Steel
US32D(630)
Steel
USP
B
700
Pulls & Plates
How to Order:
(600) Primed
E
Exterior Hardware
Electric Power Transfer Prep
Electric Through Wire
Electric Through Wire + Monitoring
Security Fasteners - Torx
Wood Fasteners
F
Options
* EPT
* TW8
* TW8M
SF
WD
Stops
Length
83"
85"
95"
120"
Other lengths available up to 120”, consult factory. Handing is required.
Miscellaneous Hardware
* Full Mortise Models Only
G
Ives Architectural hardware products
A25
A26
Hinges & Pivots
Continuous Hinges
Pin and Barrel Hinges - Clearance Requirements
Pulls & Plates
1/8”
3/16”
B
Hinge
Side
Clearance
Hinge
Side
Clearance
1/8”
Hinge
Side
Clearance
1/32”
Frame
Irregularity
1/32”
Frame
Irregularity
1/16”
Frame
Irregularity
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Hinge
Side
Clearance
SINGLE DOOR
Door Under-Sizing
Hinge-Side Lock-Side
Frame Beveled Door Square
Beveled
Model
Clearance ClearanceIrregularity Clearance Edged
Edged
600
602
700
702
705
705*
711
715
1/4" 1/8"1/32"1/32"
13/32"7/16"
1/8" 1/8"1/32"1/32"9/32"5/16"
1/4" 1/8"1/32"1/32"
13/32"7/16"
1/8" 1/8"1/32"1/32"9/32"5/16"
3/8" 1/8"1/32"1/32"
17/32"9/16"
1/2" 1/8"1/32"1/32"
21/32"11/16"
7/32" 1/8"1/32"1/32"3/8"13/32"
1/4" 1/8"1/32"1/32"
13/32"7/16"
* Use the Adjusta-Studs with 705
G
Miscellaneous Hardware
F
Exterior Hardware
PAIR OF DOORS
Door Under-Sizing
A26
Square Square BeveledBeveled
Hinge-Side Lock-Side
Frame Beveled Door Edged
Edged
Edged
Edged
Model
Clearance Clearance Irregularity Clearance
Total
Each Door
Total
Each Door
600 1/4" 3/16"1/16" 1/16" 3/4"
602 1/8" 3/16"1/16" 1/16" 1/2"
700
1/4" 3/16"1/16" 1/16" 3/4"
702
1/8" 3/16"1/16" 1/16" 1/2"
705 3/8" 3/16"1/16" 1/16" 1"
705* 1/2" 3/16"1/16" 1/16"1-1/4"
711
7/32" 3/16"1/16" 1/16"11/16"
715
1/4" 3/16"1/16" 1/16" 3/4"
* Use the Adjusta-Studs with 705
Ives Architectural hardware products
705 with Adju
3/8" 13/16"13/32"
1/4" 9/16"9/32"
3/8" 13/16"13/32"
1/4" 9/16"9/32"
1/2" 1-1/16"17/32"
5/8" 1-5/16"21/32"
11/32" 3/4"3/8"
3/8" 13/16"13/32"
Hinge
Side
Clearanc
Continuous Hinges
For Doors Weighing up to 600 pounds
• Non Handed
• 1/8” Inset
• 48" Maximum Door Width
• Non Handed
• Bevel or Square Edge Door
I ve s 5 0 0 , 6 0 0 , 7 0 0
B
1/2”
1/8"
3/8”
1/8”
GA 0.075” Hi n ge T h i ck n es s
2-1/4 ”
1-3/4”
C
1/16”
1/4 ”
USP
Clearance for
Square Edge
5/16" Clearance for
Beveled Edge
US32D
D
Custom Paint Available, on 600
consult factory.
For Doors Weighing up to 600 pounds
• Non Handed
• Flush Mounted, No Inset
• 48" Maximum Door Width
• Bevel or Square Edge Door
US32D
Custom Paint Available, on 602
consult factory
7/16”
FRAME
[12.7]
1/2"
[12.7]
3/4"
[19.1]
[1.3]
GA. 0.050"
[1.6]
1-3/4”
1/16"
7/32" [5.6] HINGE ALLOWANCE
I ve s 6 0 2 , 7 0 2
1 1/16"
3/4"
[19.1]
1-3/4”
[44.5]
1/8"
[9.5]
1/2"
3/8"
[9.5]
5/8"
[15.9]
[55.5]
2 3/16"
2" [50.8]
DOOR
G A 0 .0 7 5 ”
Hi n ge T h i ck n es s
3/8”
1-3/4”
1/8” Clearance for
Square Edge
5/32" Clearance for
Beveled Edge
Ives Architectural hardware products
G
USP
GA. 0.060"
[1.5]
Miscellaneous Hardware
US Numbers
GA 0.075" HINGE THICKNESS
F
Finishes 602702
BHMA
600630
HINGE
Exterior Hardware
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
1/4"-20 x 3/4" Self Drilling Self Tapping Screws,
Cover Clips
Optional SEC - Security Fasteners Available
E
Full Surface Pin and Barrel Continuous Hinge
Stops
602
702
Material
602- 1012 Cold-Rolled Steel
702 - 14 Gauge Type 304 Stainless Steel
1/4" Diameter 304 Stainless Pin with
Nylon Split Bearing
Brushed Aluminum Leaf Covers
Latches, Catches & Bolts
Finishes 600700
BHMA
600630
US Numbers
Flush Bolts & Coordinators
Material
600- 1012 Cold-Rolled Steel
700- 14 Gauge Type 304 Stainless Steel
1/4" Diameter 304 Stainless Pin with
Nylon Split Bearing
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
#10 X 1/2" Self Drilling Self Tapping Screws,
#10 X 1" Wood Screws
Optional SEC - Security Fasteners Available
A27
Full Mortise Pin and Barrel Continuous Hinge
Hinges & Pivots
600
700
A27
A28
Hinges & Pivots
Continuous Hinges
611
711
Swing Clear Pin and Barrel Continuous Hinge
For Doors Weighing up to 600 pounds
• Non Handed
• Edge Guard
• 48" Maximum Door Width
• Square Edge Door
B
Pulls & Plates
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
#10 X 1/2" Self Drilling Self Tapping Screws
#10 X 1" Wood Screws
Optional SEC - Security Fasteners
Available
C
Flush Bolts & Coordinators
Material
611- 1012 Cold-Rolled Steel
711- 14 Gauge Type 304 Stainless Steel
1/4" diameter 304 stanless pin with
nylon split bearings
I ve s 6 1 1 , 7 1 1
1-3/8”
3/8”
1-9/16”
1-3/4”
Finishes 611711
BHMA
600630
Latches, Catches & Bolts
US Numbers
USP
3/4”
5/32” Clearance for
7/32"
Square Edge
US32D
1/4" Clearance for
Beveled Edge
D
Custom Paint Available, on 611
consult factory
705
Full Moritse, Full Wrap
Pin and Barrel Continuous Hinge
For Doors Weighing up to 600 pounds
• Non Handed
• Flush Mounted, No Inset
• 48" Maximum Door Width
• Full Wrap Edge Guard
• Bevel or Square Edge Door
1 3/8" [34.9]
1/2"
[12.7]
GA. 0.075" HINGE THICKNESS
3/4"
[19.1]
GA. 0.060"
[1.5]
5/16"
[7.9]
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
#10 X 1/2" Self Drilling Self Tapping Screws, #10 X 1" Wood Screws
Adjusta-stud 1-3/8" with 10-32 internal thread
Optional SEC - Security Fasteners Available.
5/32" [4.0] HINGE ALLOWANCE
Exterior Hardware
FRAME
0.750"
[19.0]
GA. 0.050"
[1.3]
2" [50.8]
[44.5]
HINGE
1 3/4"
E
Stops
1/4"
[6.4]
9/16" 1/2"
[14.3] [12.7]
GA 0.075” Hi n ge
T h i ck n es s
1/4”
F
Material
14 Gauge Type 304 Stainless Steel
1/4" diameter 304 stanless pin with
nylon split bearings
GA 0.075” Hi n ge T h i ck n es s
2-1/4”
1-3/4”
Note:
Provide
0.125”
Adjustment
GA 0.075”
US Numbers US32D
G
Miscellaneous Hardware
Finishes
BHMA630
GA 0.0625”
3/8”
1-7/8”
A28
I ve s 7 0 5
DOOR
3/4”
3/8 ”
3/16”
3/8" Clearance for
*
Adjusta-Stud allows up to 3/8” width adjustment which ensures proper alignment and easy installation. Adjusta-Stud also makes it possible for future adjustments of the door on the frame through repositioning.
Ives Architectural hardware products
Square Edge
13/32" Clearance for
Beveled Edge
Continuous Hinges
For Doors Weighing up to 600 pounds
• Non Handed
• Flush Mounted, No Inset
• Half Wrap Edge Guard
• 48" Maximum Door Width
• Square Edge Door
A29
Full Mortise, Half Wrap
Pin and Barrel Continuous Hinge
Hinges & Pivots
715
Pulls & Plates
B
Standard lengths 83", 85", 95", 120"
Standard Mounting Hardware
#10 X 1/2" Self Drilling Tek Screws,
#10 X 1" Wood Screws
Optional SEC - Security Fasteners Available
Material
14 Gauge Type 304 Stainless Steel
1/4" diameter 304 stanless pin with
nylon split bearings
C
Flush Bolts & Coordinators
Finishes
BHMA630
I ve s 7 1 5
GA 0.075” Hi n ge
T h i ck n es s
3/8”
1/4”
1-3/4”
D
Custom Paint Available,
consult factory
Latches, Catches & Bolts
US Numbers US32D
3/4”
11/4"
/4” Clearance for
Square Edge
4/32" Clearance for
Beveled Edge
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
A29
A30
Hinges & Pivots
Continuous Hinges
600/700
EPT
600/700
600/700
Top of door
TW
600/700 TW 600/700 TW
600/700
Top of door
B
Pulls & Plates
Top of door
“C
L EPT”
Flush Bolts & Coordinators
“C
L EPT”
“C
L TW”
Electrical Cutouts
Ives Pin & Barrel Continuous Hinges are available with factory modified cutouts
Topaccommodate
of door
to
most electrical frame to door requirements. Special templates
are required.
When ordering indicate the following:
1. Opening size.
2. Handing. LH, RH, RHR or LHR.
3. Manufacturer and model number of the electrical product being used.
“C
L TW”
Example;
Von Duprin EPT2
C
Because clearances may vary between door and frame manufacturer, and
locations can be influenced by the door hardware it is always recommend
contacting Ives Customer Technical for specific template information.
Latches, Catches & Bolts
For your general information following are standard locations for Von Duprin
EPT2 or EPT10, and TW (through wire)
D
Standard centerline cutout locations
E
Stops
CL = Center lineCL = Center line
From Top Edge o top of Door to Center Line of Cut-Out
G
Miscellaneous Hardware
F
Exterior Hardware
Standard
LengthEPTTW
83"30"43-19/32"
85"32"45-17/32"
95"42"55-17/32"
120"67"80-17/32"
A30
Note: See ordering guide in price book for proper placement.
Ives Architectural hardware products
Pivots
A31
Hinges & Pivots
B
Pulls & Plates
The door rests on the bottom pivot in this application. This reduces
the stress on the frame by distributing the weight of the door
throughout the floor and structure. By taking advantage of the
strength of the structure, this makes a pivot the ideal solution for
your heavy doors. Center and pocket pivots also provide an aesthetic
option for your opening.
Pivots Table Of Contents
page
C
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Pocket Pivots
91105. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A50
91105F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A50
Flush Bolts & Coordinators
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A32
Selection Chart and Parts Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A32
How To Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A33
7212 . . . . . . . . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A34
7212V . . . . . . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A34
7215, 7215F . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A35
7222 . . . . . . . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A36
7226, 7226F . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A37
7227, 7227F . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A38
7230F . . . . . . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A39
7237F . . . . . . . . . . . . . . . . . . . . 3/4" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A40
7244F . . . . . . . . . . . . . . . . . . . . 1-1/2" Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A41
7245F . . . . . . . . . . . . . . . . . . . . 1-1/2" Offset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A42
7212-722V-7222 INT . . . . . . Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A43
7215-7226-7227 INT . . . . . . Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A43
7215F-7226F-7227F INT. . . Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A43
7230F-7237F INT. . . . . . . . . Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A44
7244F-7245F INT. . . . . . . . . Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A44
7215PT-7226PT-7227PT. . Intermediate, Electrified. . . . . . . . . . . . . . . . . . . . A45
7253 . . . . . . . . . . . . . . . . . . . . . Center Hung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A46
7255 . . . . . . . . . . . . . . . . . . . . . Center Hung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A47
7255J . . . . . . . . . . . . . . . . . . . . Center Hung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A47
7256 . . . . . . . . . . . . . . . . . . . . . Center Hung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A48
7259 . . . . . . . . . . . . . . . . . . . . . Center Hung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A49
Ives Architectural hardware products
A31
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A32
Hinges & Pivots
Pivots
A32
7200 Series Pivots
General Information:
Complete line of 3/4" offset, 1-1/2" offset, center hung, intermediate and
power transfer pivots with all exposed parts made of brass or stainless
steel for maximum corrosion resistance.
High strength brass and stainless steel forgings, and castings for rated
and non-rated doors combined with precision bearings for smooth operation.
Stainless steel machine screws and wood screws standard. Positive
locking vertical adjustment mechanism allows the installer to precisely
position the door and balance the load.
Last digit in pivot set number reflects the maximum door weight in
hundreds of pound, e.g., 7215 = 500 pounds. For sets designated as
“heavy duty”, add 1,000 pounds, e.g., 7237F HD set = 1700 pounds. Pivots
for lead lined doors are available, consult factory.
7200 series Pivot Selection Chart
Pivot Pivot Type Bottom Mounting
UL Listing
Max. Door
Handing
When Ordering Separate Parts
Set
StyleWeight
Top Bottom
Intermediate
7212
3/4" Offset
Jamb Mounted
7212V
3/4" Offset
Jamb Mounted
7215
3/4" Offset
Jamb Mounted
7215F
3/4" Offset
Jamb Mounted
3 Hour
none
200
LH or RH
7212-7215-7222-7226-7227 TOP
7212 BTM
7212-7212V-7222 INT
none
200
LH or RH
7212V TOP
7212 BTM
7212-7212V-7222 INT
20 Minute
500
LH or RH
7212-7215-7222-7226-7227 TOP
7215 BTM
7215-7226-7227 INT
500
LH or RH
7215F-7226F-7227F TOP
7215F BTM
7215F-7226F-7227F INT
7222
3/4" Offset
Floor Mounted
none
200
LH or RH
7212-7215-7222-7226-7227 TOP
7222 BTM
7212-7212V-7222 INT
7226
3/4" Offset
Floor Mounted
20 Minute
600
Non-Handed
7212-7215-7222-7226-7227 TOP
7226 BTM
7215-7226-7227 INT
7226F
3/4" Offset
Floor Mounted
3 Hour
600
Non-Handed
7215F-7226F-7227F TOP
7226F BTM 7215F-7226F-7227F INT
7227
3/4" Offset Mortise Cement Case
20 Minute
700
Non-Handed
7212-7215-7222-7226-7227 TOP
7227F
3/4" Offset Mortise Cement Case
3 Hour
700
Non-Handed
7215F-7226F-7227F TOP
7227F BTM 7215-7226-7227 INT
7230F
3/4" Offset
3 Hour
1,000
Non-Handed
7230F-7237F TOP
7230F BTM 7215F-7226F-7227F INT
7237F
3/4" Offset Mortise Cement Case
3 Hour
1,750
Non-Handed
7230F-7237F TOP
7237F BTM 7230F-7237F INT
7244F
1-1/2" Offset
3 Hour
400
Non-Handed
7244F-7245F TOP
7244F BTM 7230F-7237F INT
7245F
1-1/2" Offset Mortise Cement Case
3 Hour
500
Non-Handed
7244F-7245F TOP
7245F BTM 7244F-7245F INT
7253
Center Hung
Floor Mounted
none
300
Non-Handed
7253-7255-7255J-7256 TOP
7253 BTM
7244F-7245F INT
Floor Mounted
Floor Mounted
7227 BTM
7215-7226-7227 INT
7255
Center Hung
Floor Mounted
none
500
Non-Handed
7253-7255-7255J-7256 TOP
7255 BTM
none
7255J
Center Hung
Jamb Mounted
none
500
Non-Handed
7253-7255-7255J-7256 TOP
7255J BTM
none
7256
Center Hung Mortise Cement Case
none
600
Non-Handed
7253-7255-7255J-7256 TOP
7256 BTM
none
7259
Center Hung Mortise Cement Case
none
1,000
Non-Handed
7259 TOP
7259 BTM
none
Ives Architectural hardware products
Pivots
- LH - US3
B
Pulls & Plates
Pivot: 7212
7212V
7215
7215F
7222
7226
7226F
7227
7227F
7230F
7237F
7244F
7245F
7253
7255
7255J
7256
7259
A33
7212 -
Hinges & Pivots
How to Order:
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
Pivot Style: Blank Top and bottom set
TOP Top pivot only
BTM
Bottom pivot only
INT
Intermediate pivot only
PT INT Power transfer intermediate pivot only
Hand:
LH
RH
Left hand door
Right hand door
E
Stops
Finish:
US3
US4
US10
US10B
US26
US26D
SP4
SP10
SP28
SP313
SPBLK
USP
optional finishes are available, consult factory
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
A33
7212 Pivot Set
Pivots
7212 Pivot Set
3/4" Offset Pivot
•
•
•
•
•
•
7212 Pivot Set
Handed
Top, header mount
Bottom, jamb mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 200 pounds
Vertical adjustment range 3/16", with positive locking
Optional 7212-7212V-7222 Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A47.
Meets ANSI/BHMA A156.4 C07131
7212V Pivot Set
7212V 3/4" Offset Pivot
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
7212 Pivot Set
7212 7212 Pivot Set
B
Pulls & Plates
A34
Hinges & Pivots
212 Pivot Set
7212V Pivot Set
•
•
•
•
•
•
Handed
Top, jamb
7212Vmount
Pivot Set
Bottom, jamb mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 200 pounds
Vertical adjustment range 3/16", with positive locking
E
Stops
Optional 7212-7212V-7222 Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A47.
7212V Pivot Set
G
Miscellaneous Hardware
F
Exterior Hardware
7212V Pivot Set
A34
Ives Architectural hardware products
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
US26 US26D
625
626
Pivots
7215 Pivot Set
7215F Pivot Set
7215 - Ul Listed 20 minute fire doors
7215 Pivot Set
7215F - UL Listed 3 hour fire doors
7215F Pivot Set
C
Optional 7215-7226-7227 or 7215F-7226F-7227F Intermediate Pivot
(handed) for each additional 100 pounds or doors over 7'. See page A47.
Optional 7215PT Power Transfer, non-load bearing. See page A49
Flush Bolts & Coordinators
Meets ANSI/BHMA A156.4 C07131
Handed
Top, header mount
Bottom, jamb mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 500 pounds
Vertical adjustment range 3/16", with positive locking
WP - optional weather resistant bottom pivot is modified for
7215 Pivot
Set
improved
corrosion
resistance. Available in US26D (626) or
7215F Pivot Set
US32D (630) only.
B
7215 Pivot Set
7215F Pivot Set
•
•
•
•
•
•
•
Pulls & Plates
A35
7215F 3/4" Offset Pivot
Hinges & Pivots
7215 Pivot Set
7215
7215F Pivot Set
D
Latches, Catches & Bolts
E
Stops
7215
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
7215F
Plated Finishes steel
US Number
US3
US10
BHMA Number 632
639
US32 US32D
629
630
Painted Finishes steel
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
US26 US26D
625
626
F
G
Miscellaneous Hardware
Ives Architectural hardware products
Exterior Hardware
SP313 SPBLK
695
622
A35
Pivots
A36
Hinges & Pivots
7222 Pivot Set
7222
B
Pulls & Plates
Optional 7212-7212V-7222 Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A47.
7222 Pivot Set
Meets ANSI/BHMA A156.4 C07162
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Set
• Handed
• Top, header mount
• Bottom, base plate mount
• Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
• Maximum door load 200 pounds
• Vertical adjustment range 3/16", with positive locking
7222 Pivot Set
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
7222 Pivot Set
3/4" Offset Pivot
A36
Ives Architectural hardware products
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
US26 US26D
625
626
7226 Pivot Set
7226F Pivot Set
Pivots
A37
C
7226F - UL Listed 3 hour fire doors
Optional 7215-7226-7227or 7226F-722 Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A47.
Optional 7226PT Power Transfer (four wires), non-load bearing. See page A49
Flush Bolts & Coordinators
7226 - Ul Listed 20 minute fire doors
Non-handed
Top, header mount
Bottom, base plate mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 600 pounds
Vertical adjustment range 3/16", with positive locking
B
Meets ANSI/BHMA A156.4 C07162
7226 Pivot Set
7226F Pivot Set
•
•
•
•
•
•
Pulls & Plates
7226 Pivot Set
7226F Pivot Set
7226 Pivot Set
7226F Pivot Set
Hinges & Pivots
7226
7226F 3/4" Offset Pivot
D
Latches, Catches & Bolts
E
Stops
7226
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10 BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
7226F
Plated Finishes steel
US Number US3
US10
BHMA Number 632
639
US32 US32D
629
630
Painted Finishes steel
US Number SP4
SP10
BHMA Number 706
691
SP28
689
US26 US26D
625
626
F
Exterior Hardware
G
Miscellaneous Hardware
SP313 SPBLK
695
622
Ives Architectural hardware products
A37
Pivots
7227
7227F 3/4" Offset Pivot
7227 Pivot Set
7227F Pivot Set
7227 Pivot
Set
7227F Pivot
Set
7227 Pivot Set Meets ANSI/BHMA A156.4 C07121
7227F Pivot Set
7227 - Ul Listed 20 minute fire doors
7227F - UL Listed 3 hour fire doors
•
•
•
•
•
•
Non-handed
Top, header mount
Bottom, base plate mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 700 pounds
Vertical adjustment range 3/16", with positive locking
Optional 7215-7226-7227 or 7215F-7226F-7227F Intermediate Pivot (handed) for
each additional 100 pounds or doors over 7'. See page A47.
Optional 7227PT Power Transfer (four wires), non-load bearing. See page A49.
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A38
Hinges & Pivots
7227 Pivot Set
7227F Pivot Set
A38
Ives Architectural hardware products
7227
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
7227F
Plated Finishes steel
US Number US3
US10
BHMA Number 632
639
US32 US32D
629
630
Painted Finishes steel
US Number SP4 SP10
BHMA Number 706
691
SP28
689
US26 US26D
625
626
SP313 SPBLK
695
622
Pivots
7230F Pivot Set
•
•
•
•
•
•
Non-Handed
Top, header mount
Bottom, base plate mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 1,000 pounds
Vertical adjustment range 3/16", with positive locking
B
Pulls & Plates
A39
Hinges & Pivots
7230F 3/4" Offset Pivot - Heavy Duty
7230F Pivot Set
C
Flush Bolts & Coordinators
Optional 7230F-7237F Intermediate Pivot (handed) for each
additional
7230F
Pivot Set100 pounds or doors over 7'. See page A48.
Meets ANSI/BHMA A156.4 C07162
7230F
Pivot3 Set
UL Listed
Hour Fire Doors
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
Painted Finishes steel
US Number SP4 SP10
BHMA Number 706
691
SP28
689
G
US32 US32D
629
630
Miscellaneous Hardware
Plated Finishes steel
US Number US3
US10
BHMA Number 632
639
SP313 SPBLK
695
622
Ives Architectural hardware products
A39
Pivots
A40
Hinges & Pivots
7237F Pivot Set
7237F 3/4" Offset Pivot - Heavy Duty
7237F Pivot Set
•
•
•
•
•
•
Non-Handed
Top, header mount
Bottom, mortised cement case mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 1,750 pounds
Vertical adjustment range 3/16", with positive locking
7237F Pivot Set
Optional 7230F-7237F Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A48.
7237F Pivot Set
Meets ANSI/BHMA A156.4 C07111
UL Listed 3 Hour Fire Doors
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A40
Ives Architectural hardware products
Plated Finishes steel
US Number
US3
US10
BHMA Number 632
639
US32 US32D
629
630
Painted Finishes steel
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
Pivots
Non-Handed
Top, header mount
Bottom, base mount
Use with 1-3/4" minimum door thickness
Maximum door load 400 pounds
Vertical adjustment range 3/16", with positive locking
C
Flush Bolts & Coordinators
Optional 7244F-7245F Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A48.
B
•
•
•
•
•
•
Pulls & Plates
A41
Hinges & Pivots
7244F 1-1/2" Offset Pivot - Heavy Duty
D
Latches, Catches & Bolts
Meets ANSI/BHMA A156.4 C07162
UL Listed 3 Hour Fire Doors
E
Stops
F
Exterior Hardware
US32 US32D
629
630
Painted Finishes steel
US Number SP4 SP10
BHMA Number 706
691 SP28
689
SP313 SPBLK
695
622
G
Miscellaneous Hardware
Plated Finishes steel
US Number US3
US10
BHMA Number 632
639
Ives Architectural hardware products
A41
Pivots
A42
Hinges & Pivots
7245F Pivot Set
7245F 1-1/2" Offset Pivot - Heavy Duty
B
Pulls & Plates
•
•
•
•
•
•
Non-Handed
Top, header mount
Bottom, mortised cement case mount
Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2"
Maximum door load 500 pounds
Vertical adjustment range 3/16", with positive locking
7245F Pivot Set
Optional 7244F-7245F Intermediate Pivot (handed) for each
additional 100 pounds or doors over 7'. See page A48.
7245F Pivot Set
Meets ANSI/BHMA A156.4 C07121
UL Listed 3 Hour Fire Doors
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
7245F Pivot Set
A42
Ives Architectural hardware products
Plated Finishes steel
US Number US3
US10
BHMA Number 632
612
US32 US32D
629 630
Painted Finishes steel
US Number SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
Intermediate Pivots
A43
NFPA 80, Section
3-3.8 requires
Intermediate
Pivotintermediate pivot on some fire door applications, consult factory. Use
for
door
heights
7212V-7222 INT over 7'0" and one every 2'6" or . Use for door weight
Intermediate Pivot
over the pivot set limit. One additional for every additional 100 pounds. Door thickness
7212V-7222 INT
1-3/4" mimumum with 1/8" bevel in 2".
Hinges & Pivots
Intermediate Pivot
7212V-7222 INT
7212-7212V-7222 INT
• Use with 7212, 7212V or 7222 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.
B
Intermediate Pivot
7212V-7222 INT
Pulls & Plates
Meets ANSI/BHMA A156.4 C07382
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
Intermediate Pivot
7215-7226-7227 INT
7215F-7226F-7227F INT
Intermediate Pivot
7215-7226-7227 INT
7215F-7226F-7227F INT
7215-7226-7227
INT
Intermediate
Pivot
• INT
Use with 7215, 7226 or 7227 3/4 Offset Pivot
7215-7226-7227
• Handed
7215F-7226F-7227F
INT
• Vertical adjustment 3/16", include positive locking.
Stops
7215F-7226F-7227F INT:
UL listed 3 hour fire doors
Meets ANSI/BHMA A156.4 C07371
E
7215-7226-7227 INT:
UL listed 20 minute fire doors
Meets ANSI/BHMA A156.4 C07321
7215F-7226F-7227F INT
• Use with 7215F, 7226F or 7227F 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.
F
Exterior Hardware
Intermediate Pivot
7215-7226-7227 INT
7215F-7226F-7227F INT
G
Miscellaneous Hardware
Ives Architectural hardware products
A43
A44
Hinges & Pivots
Intermediate Pivot
Intermediate Pivot7230F-7237F Intermediate
INT
Pivots
7230F-7237F INT
Intermediate Pivot
7230F-7237F INT
7230F-7237F INT
• Use with 7230F or 7237F 3/4 Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.
B
Pulls & Plates
UL listed 3 hour fire doors
Meets ANSI/BHMA A156.4 C07311
Intermediate Pivot
7244F-7245F INT
Intermediate Pivot
7244F-7245F INT
E
Intermediate Pivot
7244F-7245F INT
G
Miscellaneous Hardware
F
Exterior Hardware
UL listed 3 hour fire doors
Meets ANSI/BHMA A156.4 C07371
A44
Intermediate Pivot
7244F-7245F INT
7244F-7245F
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Intermediate Pivot
7230F-7237F INT
Ives Architectural hardware products
• Use with 7244F or 7245F 1-1/2" Offset Pivot
• Handed
• Vertical adjustment 3/16", include positive locking.
Power Transfer Intermediate Pivot
Pivots
7215-7226-7227 PT
B
Pulls & Plates
Use with 7215, 7226 or 7227 3/4" Offset Pivots
Four wires, 28 gauge
Optional 8 wire available
Rated 50 VDC or VAC @ 3.5 amps. Continuous or
16 amps pulse, maximum pulse 400 milliseconds.
Non-load bearing
Use with 1-3/4" thick door minimum, 1/8" bevel in 2".
A45
•
•
•
•
•
•
Hinges & Pivots
7215PT-7226PT-7227PT Power Transfer Pivot
C
Flush Bolts & Coordinators
Power Transfer Intermediate Pivot
7215-7226-7227 PT
D
Latches, Catches & Bolts
E
Stops
US10
612
US10B
613
US26 US26D
625
626
Painted Finishes brass
US Number SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
F
US4
606
Exterior Hardware
Plate Finishes brass
US Number US3
BHMA Number 605
G
Miscellaneous Hardware
Ives Architectural hardware products
A45
Pivots
Hinges & Pivots
7253 Pivot Set
A46
7253 C
Flush Bolts & Coordinators
B
Pulls & Plates
7253 Pivot Set
Meets ANSI/BHMA A156.4 C07032
•
•
•
•
•
•
•
•
Non-Handed
Top, header mount
Bottom, base plate mount
Easy installation tilt on bearing and bearing pin.
Use with 1-3/4" minimum door thickness.
Adjustable floor to door clearance 3/16" to 3/4".
Maximum door load 300 pounds
Vertical adjustment range 3/16", with positive locking
Plated Finishes brass
US Number
US3
US4
BHMA Number 605
606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706 691
SP28
689
SP313 SPBLK
695
622
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
ot Set
Center Hung Pivot
• Radius Stop (A) to clear heel of door edge.
• Pivot distance (B) 1-3/4" (44mm) minimum from jamb to centerline of pivot pin. Radius heel edge of door, 1-5/8" (41mm) minimum recommended.
• Clearance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm)
to 3/4" (19mm) by varying the depth of the mortise (C ) in the bottom of the door, refer to
Chart D. Consult factory when clearance is over 3/4" (19mm).
G
Miscellaneous Hardware
Table D
A46
Clearance Depth of Mortise
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
Ives Architectural hardware products
US26 US26D
625
626
Pivots
7255 Pivot Set
B
Pulls & Plates
• Non-Handed
7255 Pivot Set
• Top, header mount
• Bottom, base plate mount
• Easy installation tilt on bearing and bearing pin.
• Use with 1-3/4" minimum door thickness.
• Adjustable floor to door clearance 3/16" to 3/4", consultant
factory if greater than 3/4"..
• Maximum door load 500 pounds
• Vertical adjustment range 3/16", with positive locking
A47
Center Hung Pivot
Hinges & Pivots
7255 Meets ANSI/BHMA A156.4 C07032
7255 Pivot Set
C
Flush Bolts & Coordinators
D
• Radius Stop (A) to clear heel of door edge.
• Pivot distance (B) 1-3/4" (44mm) minimum from jamb to centerline of pivot pin. Radius
heel edge of door, 1-5/8" (41mm) minimum recommended.
• Clearance from bottom edge of door to floor mounting surface is adjustable from 3/16"
(5mm) to 3/4" (19mm) by varying the depth of the mortise (C ) in the bottom of the door,
refer to Chart D. Consult factory when clearance is over 3/4" (19mm).
Latches, Catches & Bolts
7255J Pivot Set
7255J Pivot Set
F
Meets ANSI/BHMA A156.4 C07042
Non-Handed
Top, header mount
Bottom, jamb mount
Easy installation tilt on bearing and bearing pin.
Use with 1-3/4" minimum door thickness.
Adjustable floor to door clearance 3/16" to 3/4", consult factory
if greater than 3/4".
Maximum door load 500 pounds
Vertical adjustment range 3/16", with positive locking
Exterior Hardware
7255J Pivot Set
•
•
•
•
•
•
•
•
E
Center Hung Pivot
Stops
7255J
7255J Pivot
Set
G
Miscellaneous Hardware
Ives Architectural hardware products
A47
7256 Pivot Set
A48
Hinges & Pivots
Pivots
7256
B
Pulls & Plates
Meets ANSI/BHMA A156.4 C07021
C
Flush Bolts & Coordinators
Center Hung Pivot
7256
Pivot Set
• Non-Handed
• Top, header mount
• Bottom, base frame mount
• Easy installation tilt on bearing and bearing pin.
• Use with 1-3/4" minimum door thickness.
• Adjustable floor to door clearance 3/16" to 3/4", consult factory
if greater than 3/4".
• Maximum door load 600 pounds
• Vertical adjustment range 3/16", with positive locking
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
vot Set
A48
• Radius Stop (A) to clear heel of door edge.
• Pivot distance (B) 1-3/4" (44mm) minimum from jamb to centerline of pivot pin. Radius heel
edge of door, 1-5/8" (41mm) minimum recommended.
• Clearance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm)
to 3/4" (19mm) by varying the depth of the mortise (C ) in the bottom of the door,
refer to Chart D. Consult factory when clearance is over 3/4" (19mm).
Table D
Clearance Depth of Mortise
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
Ives Architectural hardware products
Plated Finishes brass
US Number US3
US4
BHMA Number 605
606
US10 US10B
612
613
Painted Finishes brass
US Number SP4
SP10
BHMA Number 706
691
SP28
689 US26 US26D
625
626
SP313 SPBLK
695
622
7259 Pivot Set
Pivots
B
Non-Handed
Top, header mount
Bottom, base frame mount
Easy installation tilt on bearing and bearing pin.
Use with 2" minimum door thickness.
Adjustable floor to door clearance 3/16" to 3/4", consult factory
if greater than 3/4".
Maximum door load 1,000 pounds
Vertical adjustment range 3/16", with positive locking
Pulls & Plates
•
•
•
•
•
7259 Pivot
Set
•
•
•
A49
Center Hung Pivot
Hinges & Pivots
7259
Flush Bolts & Coordinators
Meets ANSI/BHMA A156.4 C07011
C
Pivot Set
D
Latches, Catches & Bolts
E
Stops
3/16" (5mm)
3/8" (10mm)
1/2" (13mm)
5/8" (16mm)
3/4" (19mm)
1-3/16" (30mm)
1" (25mm)
7/8" (22mm)
3/4" (19mm)
5/8" (16mm)
Plated Finishes brass
US Number
US3
US4
BHMA Number 605 606
US10
612
US10B
613
Painted Finishes brass
US Number
SP4
SP10
BHMA Number 706
691
SP28
689
SP313 SPBLK
695
622
US26 US26D
625
626
Ives Architectural hardware products
G
Depth of Mortise
Miscellaneous Hardware
Clearance F
Table D
Exterior Hardware
• Radius Stop (A) to clear heel of door edge.
• Pivot distance (B) 1-3/4" (44mm) minimum from jamb to centerline of pivot pin. Radius heel
edge of door, 1-5/8" (41mm) minimum recommended.
• Clearance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm) to
3/4" (19mm) by varying the depth of the mortise (C ) in the bottom of the door, refer to Chart D.
Consult factory when clearance is over 3/4" (19mm).
A49
Pivots
A50
Hinges & Pivots
91105F, 91105F-PT Pocket Pivot/Hinge
B
Pulls & Plates
•
•
•
•
•
•
•
91105F Pocket Pivot
UL Listed 3 hour fire doors
or 20 minute wood fire doors
Meets ANSI/BHMA A156.4 C07611
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Non-handed
All stainless steel construction.
Allows door to open a full 90 (* degree mark)
Full mortise
90 pound load bearing
Use two for doors up to 7'0" and over 7'0" use three.
PT, Power Transfer version has four 28 gauge wires (contact factory
for eight wire version). Rated 50 VOC
or VAC @ 3.5 amps. Continuous or 16 amps pulse.
Maximum pulse 400 milliseconds.
Door Portion
Cutout
Pocket
Pivot
1-3/8
1-1/8
1-9/64
E
Stops
1-9/64
Door
Portion
CL
of Door
Jamb
Portion
1-1/8
F
Exterior Hardware
5-17/32
Miscellaneous Hardware
Plated Finishes steel
US Number US3
US10
BHMA Number 632
639
G
Painted Finishes steel
US Number USP SP313
BHMA Number 600
695
A50
Finishes stainless steel
US Number US32 US32D
BHMA Number 629
630
Ives Architectural hardware products
US10B
640
Pulls & Plates
A
Hinges & Pivots
Table Of Contents
B1
Pulls & Plates
Pulls, Plates and Trim
Pulls
page
8102HD Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2
8103HD Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2
8103EZHD Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3
8105 Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3
8111-5 Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B4
8112-5 Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B4
8121 Door Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5
8190HD Offset Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B5
C
Flush Bolts & Coordinators
Push and Pull Plates
8200 Push Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
8300 Pull Plate (less pull). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B6
8302 Pull Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8303 Pull Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8305 Pull Plate (with 8105). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B7
8311 Pull Plate (with 8111-5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8
Latches, Catches & Bolts
D
Push Bars
9100HD Pushbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B8
9103EZHD Pushber & Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B9
9190HD Pushbar & Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B9
Long Door Pulls
9264, 9266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B10
E
Stops
Vandal Resistant Trim
VR810-DT, VR814DT Vandal Resistant Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B11
VR810-NL, VR814-NL Vandal Resistant Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B11
VR900, VR904 Vandual Resistant Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B12
VR900LLP, VR904LLP Vandual Resistant Trim. . . . . . . . . . . . . . . . . . . . . . . . . . B12
VR910-DT, VR914-DT Vandual Resistant Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . B13
VR910-NL, VR914-NL Vandual Resistant Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . B13
VR910M-DT, VR914M-DT Vandual Resistant trim. . . . . . . . . . . . . . . . . . . . . . . . B13
VR910M-NL, VR914M-NL Vandual Resistant Trim. . . . . . . . . . . . . . . . . . . . . . . . B13
F
Exterior Hardware
Protection Plates
8400 Protection Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13-14, 18
8402 Protection Plate (UL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B13-14, 18
Miscellaneous Hardware
Mounting Detail
Special Mounting Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B15-17
G
Ives Architectural hardware products
B1
Hinges & Pivots
Architectural Door Trim
A
8102HD Door Pull - 3/4” Round
Available mounting – standard, F, H-I-L, or J see pages B15 and B16
– 5/16-18” mounting screw size
Available Sizes
6”, 8”, 10”
3/4”
ROUND
C
Flush Bolts & Coordinators
B2
Pulls & Plates
Product No.
Projection
“A”
Clearance
Center to Center
“B”
8102-6 2-1/4”1-1/2”
8102-8 2-1/4”1-1/2”
8102-0 2-1/4”1-1/2”
6”
8”
10”
Finishes brass
US Number
US3
US15
BHMA
US4
US10
US10B
Overall Length
“C”
6-3/4”
8-3/4”
10-3/4”
US26 US26D*
605606 612 613 619 625 626
Finishes stainless steel
US Number US32D*
BHMA630
Latches, Catches & Bolts
Finishes aluminum
US Number US28
BHMA628
D
* Available with Antimicrobial Coating, use suffix AM
8103HD Door Pull - 1” Round
Available mounting – standard, F, H-I-L, or J see pages B15 and B16
– 3/8-16” mounting screw
Available Sizes
E
Stops
8”, 10”, 12”
Product No.
Projection
“A”
Clearance
Exterior Hardware
8103-8 8103-0 8103-2 F
Finishes brass
US Number
US3
BHMA
1”
ROUND
US4
1-1/2”
1-1/2”
1-1/2”
US10
8” 10” 12” US10B
629630
G
Finishes aluminum
US Number US28
BHMA628
* Available with Antimicrobial Coating, use suffix AM
Ives Architectural hardware products
US15
Overall Length
“C”
9”
11”
13”
US26 US26D*
605606 612 613 619 625 626
Finishes stainless steel
US Number US32 US32D*
BHMA
Miscellaneous Hardware
B2
2-1/2” 2-1/2” 2-1/2” Center to Center
“B”
Architectural Door Trim
A
Available mounting – standard, O, H-I-L, J see pages B15 and B17
with Heavy Duty 3/8-16” mounting screws
Hinges & Pivots
8103EZHD Door Pull - 1” Round
Large 2-1/2” Clearance for the Accessibility Applications
Available Sizes
8”, 10”, 12”
Projection
“A”
Clearance
2-1/2”
CLEARANCE
Finishes brass
US Number
US3
BHMA
US4
2-1/2” 2-1/2” 2-1/2” US10
8” 10” 12” US10B
US15
9”
11”
13”
US26 US26D*
605606 612 613 619 625 626
C
Finishes stainless steel
US Number US32 US32D*
BHMA
Flush Bolts & Coordinators
1”
ROUND
3-1/2” 3-1/2” 3-1/2” Overall Length
“C”
B3
8103EZ 8103EZ 8103EZ Center to Center
“B”
Pulls & Plates
Product No.
629630
Latches, Catches & Bolts
Finishes aluminum
US Number US28
BHMA628
D
* Available with Antimicrobial Coating, use suffix AM
8105 Door Pull - 1” Flattened
Available mounting – standard or F see page B15
– 1/4 - 20” mounting screws
Available Sizes
8105-6 8105-8 8105-0 2” 2” 2” US10
US10B
6-1/2”
8-1/2”
10-1/2”
US15
US26 US26D*
605606 612 613 619 625 626
Miscellaneous Hardware
Finishes stainless steel
US Number US32D*
F
BHMA
US4
6” 8” 10” Overall Length
“C”
Exterior Hardware
Finishes brass
US Number
US3
1”
FLATTED
1/2 ROUND
Center to Center
“B”
E
Projection
“A”
Stops
6”, 8”, 10”
Product No.
BHMA630
G
Finishes aluminum
US Number US28
BHMA628
* Available with Antimicrobial Coating, use suffix AM
Ives Architectural hardware products
B3
Architectural Door Trim
Hinges & Pivots
8111-5 Door Pull
A
Available mounting – 1/4-20” mounting screws, standard see page B15
Size
5-1/4”
Product No.
Projection
“A”
Pulls & Plates
8111-5 B4
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
1-13/16” Finishes brass
US Number
US3
BHMA
Center to Center
“B”
US4
5-1/4” US10
US10B
1”
ROUND
BASE
BHMA630
Finishes aluminum
US Number US28
BHMA628
* Available with Antimicrobial Coating, use suffix AM
1”
FLATTED
1/2 ROUND
8112-5 Door Pull
Standard sheet metal screws for surface mounting
Size
5-1/4”
Product No.
Stops
Projection
“A”
2-13/16” Center to Center
“B”
5-5/8” E
Finishes brass
US Number US26D*
F
Exterior Hardware
* Available with Antimicrobial Coating, use suffix AM
G
US26 US26D*
Finishes stainless steel
US Number US32D*
BHMA626
Miscellaneous Hardware
6-1/4”
605606 612 613 619 625 626
8112-5 B4
US15
Overall Length
“C”
1-7/8”
SURFACE
MOUNTED
1”
FLATTED
1/2 ROUND
Ives Architectural hardware products
Overall Length
“C”
7-1/2”
Architectural Door Trim
5-3/4”
Product No.
Projection
“A”
8121-5 A
Available mounting – K see page B16
Size
Hinges & Pivots
8121 Door Pull
Center to Center
“B”
3-1/2” Overall Length
“C”
5-3/4” 8-3/4”
Pulls & Plates
B5
Finishes brass
US Number US26D*
BHMA626
* Available with Antimicrobial Coating, use suffix AM
B
Flush Bolts & Coordinators
C
C
1-1/2”
HOSPITAL
A
D
Latches, Catches & Bolts
8190HD 90° Offset Door Pull
Available mounting – with heavy duty 3/8-16” mounting screws, standard H-I-L, N
or O see page B15 and B17
Available Sizes
8”, 10”, 12”, 18”
3-1/4”
3-1/4”
3-1/4”
3-1/4”
BHMA
8”
10”
12”
18”
9”
11”
13”
19”
2-1/4”
2-1/4”
2-1/4”
2-1/4”
US4
US10
US10B
US15
US26 US26D*
605606 612 613 619 625 626
Finishes stainless steel
US Number US32 US32D*
629630
Miscellaneous Hardware
BHMA
F
1”
ROUND
Overall Length
“C”
Exterior Hardware
Finishes brass
US Number
US3
Center to Center
“B”
E
8190-8 8190-0 8190-2 8190-18 Projection
“A”
Clearance
Stops
Product No.
* Available with Antimicrobial Coating, use suffix AM
G
Ives Architectural hardware products
B5
Architectural Door Trim
Hinges & Pivots
8200 Push Plate
8300 Pull Plate, Prep for Pull (less pull)
A
Available Sizes
Plates Cut for Cylinder or Thumbturns
Plates are available with cutout for cylinder or thumbturn; standard cutout is 2” from
top and centered on plates up to 4” wide. For plates wider than 4” cutout is located
2” from outer edge, specify LH or RH. When pull location interferes with standard
cutout location a detail drawing should be furnished with the order.
Standard cutout is 1-1/4” for cylinder and 3/8” for thumbturn.
Specify CFC for cutout for cylinder or CFT for cutout for thumbturn.
2”
Finishes brass
US Number
US3
2”
BHMA
CFC
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B6
Pulls & Plates
3” x 12”
3.5” x 15”
4” x 16”
6” x 16”
8” x 16”
Special sizes are available. Consult factory.
CFT
2”
CFT
Finishes aluminum
US Number US28
E
Stops
F
Exterior Hardware
* Available with Antimicrobial Coating, use suffix AM
G
Ives Architectural hardware products
US15
US26 US26D*
605606 612 613 619 625 626
BHMA628
Miscellaneous Hardware
B6
US10B
BHMA630
2”
CFC
US10
Finishes stainless steel
US Number US32D*
2”
2”
US4
Architectural Door Trim
Pull plate
8300 Plate
3-1/2” x 15”
4” x 16”
6” x 16”
Finishes brass
US Number
US3
US10
US10B
US26 US26D*
605606 612 613 625626
Finishes aluminum
US Number US28
BHMA630
BHMA628
* Available with Antimicrobial Coating, use suffix AM
C
Flush Bolts & Coordinators
Finishes stainless steel
US Number US32D*
B7
BHMA
US4
Pulls & Plates
3/4”
ROUND
8102 Pull
6” centers
8” centers
10” centers
A
Available mounting – Standard, F, G, H-I-L, or J see pages B15 and B16
Pulls have new heavy duty 5/16-18” mounting.
Hinges & Pivots
8302
8303
Pull plate
Available mounting – Standard, F, G, H-I-L, or J see pages B15 and B16
Pulls have new heavy duty 3/8-16” mounting.
Finishes brass
US Number
US3
BHMA
US4
D
1”
ROUND
8103 Pull
8” centers
10” centers
7” centers
US10
US10B
US26 US26D*
605606 612 613 625626
BHMA630
BHMA628
* Available with Antimicrobial Coating, use suffix AM
Pull plate
8105 Pull
6” centers
8” centers
10” centers
BHMA
US4
US10
US10B
US26 US26D
605606 612 613 625626
Finishes aluminum
US Number US28
BHMA630
BHMA628
G
Finishes stainless steel
US Number US32D
Miscellaneous Hardware
Finishes brass
US Number
US3
F
8300 Plate
3-1/2” x 15”
4” x 16”
6” x 16”
Exterior Hardware
Available mounting – Standard or F see page B15
Pulls have 1/4 - 20” mounting
1”
FLATTED
1/2 ROUND
E
Finishes aluminum
US Number US28
Stops
Finishes stainless steel
US Number US32D*
8305
Latches, Catches & Bolts
8300 Plate
3-1/2” x 15”
4” x 16”
6” x 16”
* Available with Antimicrobial Coating, use suffix AM
Ives Architectural hardware products
B7
Architectural Door Trim
Hinges & Pivots
8311
A
B8
Pulls & Plates
8300 Plate
3-1/2” x 15”
4” x 16”
6” x 16”
8111-5 Pull
5-1/8” centers
Finishes brass
US Number
US3
1”
ROUND
BASE
BHMA
US4
US10
US10B
US26 US26D*
605606 612 613 625626
Finishes stainless steel
US Number US32D*
BHMA630
1”
FLATTED
1/2 ROUND
Finishes aluminum
US Number US28
BHMA628
* Available with Antimicrobial Coating, use suffix AM
9100 Series Push Bar and Pull Combinations
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Pull plate
Available mounting – Standard or F see page B15
Pulls have 1/4-20” mounting.
D
• Available in brass, stainless steel or aluminum.
• Standard fasteners furnished for 1-3/4” thick doors. Specify door
thick if other than standard.
• Special lengths are available, contact customer service.
See page B17 for special mounting requirements.
E
Stops
Caution – the length of the pushbar should not interfere with the door jamb or
cause a pinch point.
9100HD Push Bar
Product No.
9100-28 9100-33 F
Exterior Hardware
Available mounting – NO or NS see page B17
with heavy duty 3/8-16” mounting
Miscellaneous Hardware
1”
ROUND
Projection
Clearance
2-1/2” 2-1/2” Center to Center
1-1/2”
1-1/2”
28” 33” Finishes brass
US Number
US3
BHMA
US4
US10
US10B
G
BHMA
US15
US26 US26D*
605606 612 613 619 625 626
Finishes stainless steel
US Number US32 US32D*
Ives Architectural hardware products
29”
34”
Special lengths available, consult factory
629630
* Available with Antimicrobial Coating, use suffix AM
B8
Overall Length
Architectural Door Trim
A
Hinges & Pivots
9103EZHD Straight Pull/Pushbar Combo
(8103EZHD Pull + 9100HD Push)
Available mounting – NO or NS see page B17
with heavy duty 3/8-16” mounting
Product No.
CTC Push CTC Pull 8” 10” 12” 2-1/2” & 3-1/2”
2-1/2” & 3-1/2”
2-1/2” & 3-1/2”
Special lengths available, consult factory
1”
ROUND
Finishes brass
US Number
US3
US10
US10B
US15
US26 US26D*
605606 612 613 619 625 626
BHMA
C
Finishes stainless steel
US Number US32 US32D*
Flush Bolts & Coordinators
BHMA
US4
B9
28”, 33” 28”, 33” 28”, 33” Pulls & Plates
9103EZ 9103EZ 9103EZ Projection
Push & Pull
629630
* Available with Antimicrobial Coating, use suffix AM
D
Latches, Catches & Bolts
9190HD Offset Pull/Pushbar Combo
(8190HD pull + 9100HD push)
Available mounting – NO or NS see page B17
with heavy duty 3/8-16” mounting
28”, 33”
28”, 33”
28”, 33”
28”, 33”
8”
10”
12”
18”
2-1/2” & 3-1/4”
2-1/2” & 3-1/4”
2-1/2” & 3-1/4”
2-1/2” & 3-1/4”
F
BHMA
US4
US10
US10B
US15
US26 US26D*
605606 612 613 619 625 626
629630
Ives Architectural hardware products
G
* Available with Antimicrobial Coating, use suffix AM
Miscellaneous Hardware
Finishes stainless steel
US Number US32 US32D*
BHMA
Exterior Hardware
Special lengths available, consult factory
Finishes brass
US Number
US3
E
1”
ROUND
9190
9190
9190
9190
Projection
Push & Pull
Stops
Product No.
CTC Push CTC Pull B9
Long Door Pulls
Hinges & Pivots
Long Door Pulls
A
Offered in two Models:
9264 9266 Offset
Straight
•
•
•
•
•
•
B10
Pulls & Plates
Heavy 1-1/4” Round Brass or Stainless Steel
Round or Flat Tip
316 Stainless Steel
1-3/4˝, 2˝ or 2-1/4˝ Door Thickness
Round Tip Standard
Flat Tip Optional
Flush Bolts & Coordinators
Dimensions
C
Length: 36” / 20” CC
72” / 56” CC
Diameter: 1-1/4”
Projection: 2-3/4”
Special Lengths Available
D
Latches, Catches & Bolts
18” and 24”
Custom lengths available from 36” to 144”
Finishes
Ives Number
US3
BHMA
605606 613 629 630
US10B US32
US32D
E
Stops
US4
Exterior Hardware
Offset
Bracket
Flat Tip
F
Note: A middle position bracket is required for pulls over 8 feet.
G
Miscellaneous Hardware
B10
Round Tip
Ives Architectural hardware products
Vandal Resistant Trim
For use with Falcon XX or 25 Series Exit Device
Non-handed
Thru-bolts direct to the exit device
Pull operation only
Prod.
No.
Width
Height
Thru-Bolt
Pattern
Clearance
Grip to Door
Projection
VR810DT
1-3/4” wide x 7-3/4” high
1-1/2”
1-7/8”
11”
C
Finishes
US Finish
5-1/4”
US32D
BHMA630
Latches, Catches & Bolts
LHR With black grip
RHR With black grip
LHR Without black grip
RHR Without black grip
D
VR810-NL VR810-NL VR814-NL VR814-NL • For use with Falcon XX-V
• Thru-bolts direct to the exit device
• Night latch operation (cylinder not furnished)
Clearance
Grip to Door
Projection
VR810NL
1-3/4” wide x 7-3/4” high
1-1/2”
1-7/8”
5-1/4”
11”
US32D
F
With black grip
Without black grip
• For use with Falcon 25-R or 25-V Series exit devices
• Thru-bolts direct to the exit device
• Night latch operation (cylinder not furnished)
Thru-Bolt
Pattern
Clearance
Grip to Door
Projection
VR810NL-V 5-1/4”
1-3/4” wide x 7-3/4” high
1-1/2”
1-7/8”
11”
US32D
G
Prod.
No.
Width Height
Miscellaneous Hardware
VR810-NL-V VR814-NL-V Exterior Hardware
BHMA630
Finishes
US Finish
E
Thru-Bolt
Pattern
Stops
Prod.
No.
Width Height
Finishes
US Finish
Flush Bolts & Coordinators
VR814
•
•
•
•
B11
VR810
With black grip
Without black grip
Pulls & Plates
VR810-DT
VR814-DT A
All stainless steel, 11 gauge (0.120” thick), using stainless steel fasteners for door
thickness of 1-3/4” to 2-1/4”. Built-in lock protector prevents tampering on certain
models. Protective cylinder collar spins to reduce damage from pipe wrench or other
tools. Models are available with or without attractive black plastisol edge grip.
Hinges & Pivots
Vandal Resistant Trim
BHMA630
Ives Architectural hardware products
B11
Width
Height
Thru-BoltClearance
Pattern
Grip to Door
Projection
7-1/4”
2” wide x 10” high 1-1/2”
1-7/8”
A
Hinges & Pivots
VR900 RHR With black grip
VR900 LHR With black grip
VR904 RHR Without black grip
VR904 LHR Without black grip
Pulls & Plates
Vandal Resistant Trim
B12
•
•
•
•
Flush Bolts & Coordinators
Finishes
US Finish
For use with most mortise locks on outswinging doors including Schlage L9000 Series with interior L or N escutcheon, and rose trim.
Includes built-in lock protector and cylinder cutout.
Handed design allows trim to be positioned to coordinate with the
centerline of inside hardware.
11”
US32D
C
BHMA630
Latches, Catches & Bolts
VR900LLP RH With black grip
VR900LLP LH With black grip
VR904LLP RH Without black grip
VR904LLP LH Without black grip
E
Stops
D
•
•
•
•
For use with most mortise locks on outswinging doors including Schlage L9000 Series with interior L or N escutcheon, and rose trim.
Includes built-in lock protector and cylinder cutout.
Handed design allows trim to be positioned to coordinate with the
centerline of inside hardware.
Thru-Bolt Clearance
Width
Height
Pattern
Grip to Door
Projection
5-1/4”
1-7/8”
Finishes
US Finish
11”
1-3/4” wide x 10” high US32D
G
Miscellaneous Hardware
F
Exterior Hardware
BHMA630
B12
Ives Architectural hardware products
1-1/2”
Vandal Resistant Trim
•
•
•
•
For use with Von Duprin 98/99 Series rim and vertical rod exit device
Non-handed
Thru-bolts direct to the exit device
Pull operation only.
Clearance
Grip to Door
Projection
5-1/4”
1-1/2”
1-7/8”
11”
B13
Finishes
US Finish
1-3/8” wide x 7” high
US32D
BHMA630
With black grip
Without black grip
Thru-Bolt
Width
Height Pattern
Clearance
Grip to Door
Projection
5-1/4”
1-1/2”
1-7/8”
11”
US32D
D
BHMA630
VR910M-DT With black grip
VR914M-DT Without black grip
• For use with Von Duprin 9875/9975 mortise lock exit device
• Non-handed
• Thru-bolts direct to the exit device
Projection
7-1/4”
1-1/2”
1-7/8”
11”
1-3/8” wide x 7” high
E
Clearance
Grip to Door
Stops
Thru-Bolt
Width
Height Pattern
Finishes
US Finish
Latches, Catches & Bolts
Finishes
US Finish
1-3/8” wide x 7” high
C
• For use with Von Duprin 98/99 rim and vertical rod exit device
• Non-handed
• Thru-bolts direct to the exit device
Flush Bolts & Coordinators
VR910-NL VR914-NL Pulls & Plates
Thru-Bolt
Width
Height Pattern
A
With black grip
Without black grip
Hinges & Pivots
VR910-DT VR914-DT US32D
BHMA630
With black grip
With black grip
Without black grip
Without black grip
F
• For use with Von Duprin 9875/9975 Series mortise lock exit device
• Thru-bolts direct to the exit device
• Night latch operation (cylinder not furnished)
Clearance
Grip to Door
Projection
7-1/4”
1-1/2”
1-7/8”
Finishes
US Finish
11”
1-3/8” wide x 7” high
US32D
G
Thru-Bolt
Width
Height Pattern
Miscellaneous Hardware
Exterior Hardware
VR910M-NL RHR VR910M-NL LHR VR914M-NL RHR VR914M-NL LHR BHMA630
Ives Architectural hardware products
B13
Protection Plates
Hinges & Pivots
8400 Series Protection Plates
Door protection plates are available in .050” thick brass, stainless steel or aluminum; and 1/8” thick high impact polyethylene in clear
or black.
Bevel edge options; specify B4E for all four edges.
Mounting screw pack furnished standard, 16 screws per pack.
Optional screw packs are available for TEK or TORK screw heads.
Refer to the following chart for ordering.
Specify NMH for no mounting holes. (Not available on 8402)
Specify NMH-A for no mounting holes with adhesive. (Not available on 8402)
Specify CS for counter sunk mounting holes.
Specify ERS prepped with extra row of screws.
Kickplate Gasket Tape Tape is recommended when using a
brass plate on a metal door to reduce tarnishing from electrolytic
oxidation. One tape pack will cover an the perimeters of a 8” x 34”
kickplate. Order 8401 Gasket Tape.
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B14
Pulls & Plates
A
•
•
•
•
•
•
•
D
8400 Protection Plate
8402 (UL)* Protection Plate
*UL mark appears in upper right corner. Factory supplied screws must be used.
Number of screw packs required by plate size (specify TEK Screws or TORK screws).
E
Stops
22”-25”
26”-33”
34”-41”
42”-48”
4”-8”1
1
1
1
9”-16”1
1
1
1
17”-24”1
1
1
2
25”-32”1
1
2
2
33”-40”1
2
2
2
41”-48”2
2
2
2
Exterior Hardware
Finishes brass 24” x 48” max. size
US Number
US3
US4
US10
BHMA
US15
US26 US26D
605606 612 613 619 625 626
F
Finishes stainless steel
US Number US32 US32D
BHMA
629630
Finishes aluminum
US Number US28
Miscellaneous Hardware
BHMA628
G
B14
US10B
Finishes plastic
Clear and Black
Residential Grade Kickplates available Carded only, finishes PA28, PA3, PA619,
PA716, B3, B505, B619, B716
Ives Architectural hardware products
Push Plates
Hinges & Pivots
Mounting
Type Standard Mount
A
• All mounting hardware is for standard 1-3/4” door.
•Consult Customer Service if other than standard.
Type G Mount
B15
Pulls & Plates
C
Flush Bolts & Coordinators
Concealed Pull Plate Mounting
• (2) 3/8-16 x 2-1/4” brass, flat head machine screws;
plate to match.
• (2) 3/8-16 countersunk washers; plated to match
Note: 8102HD and 8105 have (2) 5/16-18 x 2-1/2” machine screws
-Options: (2) 5/16 countersunk washers
Available only for 8302, 8303, 8311 Pull Plates.
Pull mounts directly onto plate.
Plate is attached to door by 6 screws.
Note: 8302 has (2) 5/16-19 x 5/8” steel flathead zinc plated screws
Type H-I-L Mount
D
Type F Mount
• (2) 3/8-16 x 5/8” steel flat head machine screws; zinc plated.
Latches, Catches & Bolts
Standard Mounting
E
Stops
Available only for 8102HD, 8103HD, 8105, 8111, 8302, 8303, 8305 and
8311. Plate on opposite side of door must be ordered separately.
• (2) Steel screw sleeves; zinc plated.
• (2) Steel countersunk trim head machine screw; zinc plated for
reinforced metal door.
• (2) Steel countersunk trim head steel metal screw; zinc plated
for wood doors.
Note: 8102HD, 8302 will have 5/16-18
8105, 8111, 8305, 8311 will have 1/4-20
8103HD, 8303 will have 3/8-16”
Note: 8102HD and 8302 will have 5/16-18”
8103HD, 8103EZHD, 8303 will have 3/8-16
Ives Architectural hardware products
G
Available only for 8102, 8103, 810EZ or wood door pulls, 8302,
8303 pull plates and 9264, 9265, 9266 and 9267 long door pulls.
Miscellaneous Hardware
• (2) 2-1/4” steel flat head machine screws; zinc plated.
F
Reinforced Hollow Metal Door
Concealed Pull Mounting
Exterior Hardware
Wood Doors
Concealed Pull Mounting With Push Plate
B15
A
Hinges & Pivots
Architectural Door Trim
Mounting
• All mounting hardware is for standard 1-3/4” door.
• Consult Customer Service if other than standard.
Back to Back Pull Mounting
Available only for 8121-5 Pulls.
• (4) Steel screw sleeve nuts; steel zinc plated.
• (8) No. 8-32 x 1” brass oval head machine screws; plated to match.
Pulls furnished in pairs (PR).
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B16
Pulls & Plates
Type K Mount
B16
Ives Architectural hardware products
Architectural Door Trim
• Consult Customer Service if other than standard.
Type J/N Mount
Type O Mount
A
• All mounting hardware is for standard 1-3/4” door.
Hinges & Pivots
Mounting for 8103EZ, 8190, 9100, 9103EZ, 9190 and 9264, 9265, 9266 and
9267 long door pulls.
B17
Pulls & Plates
(pull)
Wood or Metal Door
Available only for 8103EZHD, 8190HD, 9100HD push/pull
combinations and 9264, 9265, 9266 and 9267 long door pulls.
Pushbar to Pull
- (1) 3/8 - 16 X 3”steel countersunk trim head machine screws with (2) set screws.
- (1) steel screw sleeve, zinc plated.
• (2) 3/8-16 x 2-1/4” blind thru - bolts; plated to match.
Type NO Push/Pull Mounting
Type N & Type O
Pushbar to Pull
- (1) 3/8 -16 X 3”steel countersunk trim head machine screws
with (2) set screws.
- (1) steel screw sleeve, zinc plated.
Free End Pushbar & Pull
- (2) 3/8 - 16 X 2-1/4” blind thru-bolts; plated to match.
E
Stops
Free End Pushbar & Pull
- (2) 3/8 - 16 X 2-1/4” brass, oval head mach screws;
plated to match.
- (2) No. 14 countersunk washers; plated to match.
Available only for 8103EZHD, 8190HD and 9100HD Series Push/Pull
Combinations.
D
Type NS-Standard Push/Pull Mounting
Type N & Standard
Wood or Metal Door
Latches, Catches & Bolts
• (2) 3/8-16 x 2-3/4” steel countersunk trim head machine screws
with (4) set screws for maximum anchoring force.
• (2) Steel screw sleeves; zinc plated.
Decorative Blind Thru - Bolt
C
Back to Back “Two-Anchor”
Flush Bolts & Coordinators
(push)
Type P Mount
F
Exterior Hardware
• (2) 3/8-16 x 2-1/4” steel countersunk trim head machine screws
with (4) set screws for maximum anchoring force.
• (2) Steel screw sleeves; zinc plated
• (2) Metal and Vinyl washers
Ives Architectural hardware products
G
Available only for 8103EZHD, 8190HD, 9100HD, 9265 and 9266 long
door pulls.
Miscellaneous Hardware
1/2” Glass Door
B17
A
Hinges & Pivots
Protection Plates
Mop Plates
• Protect the bottom of the pull side of door subject to cleaning
and mopping procedures.
• Size Ranges:4” to 6” high, 22” to 48” wide
Pulls & Plates
Kick Plates
Flush Bolts & Coordinators
B18
• Protect the bottom of the push side of doors subject to
scuffing from foot traffic.
• Recommended for all doors subject to normal use
(especially doors using a closer).
• Size Ranges: 8” to 24” high, 22” to 48” wide
Stretcher Plates
•
•
•
•
C
Latches, Catches & Bolts
Armor Plates
F
Exterior Hardware
E
Stops
D
•
•
•
G
Miscellaneous Hardware
B18
Protect doors at specific areas where consistent contact is
made by stretchers, service carts or other equipment.
Usually applied to push side of doors.
Specify “B4E” Option for beveled edges.
Size Ranges: 6” to 8” high, 22” to 48” wide
Ives Architectural hardware products
Protect lower half of doors from abuse by hard carts,
trucks and rough usage.
Usually applied to push side of single doors and both sides
of double acting doors.
Size Ranges: 26” to 48” high, 22” to 48” wide
Flush Bolts and Coordinators
Hinges & Pivots
A
Table Of Contents
B
Pulls & Plates
Flush Bolts
page
FB31, FB32, FB33 Automatic Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C2
FB41, FB42 Automatic Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C3
FB51, FB52, FB53 Automatic Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C4
FB61, FB62 Constant Latching Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C5
261 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C6
262 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C6
265 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C7
FB358 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C8
FB457 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C9
FB458 Manual Flush Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C10
DP1, DP2 Dust Proof Strike. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C11
Flush Bolts & Coordinators
C1
Coordinators
COR Series Bar Coordinator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
FL Series Filler bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C12
MB1, MB2 Mounting Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB1F, MB2F, MB3F Mounting Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
MB1V, MB2V, MB3V Mounting Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C13
COR7G, CORG Gravity Coordinator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C14
CB1 Carry Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C14
How to order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C15
Special factory prep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C16
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C1
Hinges & Pivots
Automatic Flush Bolts –
Metal Doors
FB31P Top and Bottom Bolts (Pair)
Top
Bolt
Bottom
Bolt
FB32
Top Bolt with Auxiliary Fire Latch
•
D
FB33
E
Top
Bolt
Auxiliary
Fire Latch
Meets ANSI A156.3 Type 25.
UL Listed 3 Hour Fire Doors 8'0" x 8'0"
G
Ives Architectural hardware products
FB32 Model with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
Top Bolt with Auxiliary Fire Latch and Retrofit Plate
•
Stops
F
Exterior Hardware
FB31T Top Bolt Only
FB31B Bottom Bolt Only
Meets ANSI A156.3 Type 25.
UL Listed 3 Hour Fire Doors 8'0" x 10'0"
Miscellaneous Hardware
C2
Fully Automatic—inactive door is latched, bolts are extended when active door closes, door is unlatched, bolts retract when active door
is opened.
Low Actuation Forces—Top Bolt Has No Spring Tension.
Fits standard ANSI A115.4 Door Frame Preparations.
Non-handed.
Bolt throw is 3/4" with a 7/8" vertical adjustment.
Bolt backset is 3/4"
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip. Optional rod lengths available
for top bolt only on non-fire rated openings—18", 24", 36" and 48.
DP1 or DP2 optional dust proof strike available, see page C11.
Latches, Catches & Bolts
C2
Flush Bolts & Coordinators
B
Pulls & Plates
A
•
•
•
•
•
•
•
FB33 Model with Auxiliary Fire Latch eliminates the bottom bolt and
includes a retrofit plate to cover existing bottom bolt prep.
UL Listed for Fire Doors.
Dimensions
Body Size: 1" Wide x 6-3/4" Long x 2" Deep
Guide Size: 1" Wide x 1-27/32" Long x 27/32" High x 3/32" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
Retrofit Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick
Finishes
Ives Number
US3
BHMA
605606 612 613 629630
US4
US10
US10B
US32 US32D
Automatic Flush Bolts –
Wood Doors
Fully Automatic—inactive door is latched, bolts are extended when
active door closes, door is unlatched bolts retract when active door
is opened.
Low Actuation Forces—Top Bolt Has No Spring Tension.
Non-handed.
Bolt throw is 3/4" with a 7/8" vertical adjustment.
Bolt backset is 3/4"
Meets ANSI A156.3 Type 25.
UL Listed 90 Minute Fire Doors 8'0" x 8'0"
B
Bottom
Bolt
FB41T Top Bolt Only
FB41B Bottom Bolt Only
•
FB42 Model with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
Body Size: 1" Wide x 8-1/2" Long x 2" Deep
D
Guide Size: 1" Wide x 6" Long x 1/8" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary
Fire Latch
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
US3
BHMA
605606 612 613 629630
US4
US10
US10B
US32 US32D
E
Finishes
Ives Number
Stops
Meets ANSI A156.3 Type 25.
UL Listed 20 Minute Fire Doors 8'0" x 8'0"
Latches, Catches & Bolts
Dimensions
C3
Top Bolt with Auxiliary Fire Latch
Flush Bolts & Coordinators
FB42
Top
Bolt
Pulls & Plates
DP1 or DP2 optional dust proof strike available, see page C11.
Top
Bolt
A
•
•
•
•
•
Hinges & Pivots
FB41P Top and Bottom Bolts (Pair)
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C3
Hinges & Pivots
Constant Latching Flush Bolts –
Metal Doors
A
FB51P Top and Bottom Bolts (Pair)
Top
Bolt
Constant Latching—inactive door remains latched until
the active door is opened, releasing the automatic bottom
bolt and then the top bolt can be manually released.
Inactive door will relatch automatically when closed.
Low Actuation Forces.
Fits standard ANSI A115.4 Door and Frame Preparations.
Non-handed.
3/4" bolt throw with a 7/8" vertical adjustment.
3/4" backset
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip. Optional rod lengths available
for top bolt only on non-fire rated openings—18", 24", 36" and 48".
DP1 or DP2 optional dust proof strike available, see page C11.
Bottom
Bolt
Meets ANSI A156.3 Type 27.
UL Listed 3 Hour Fire Doors 8'0" x 10'0"
FB51T Top Bolt Only
FB52
Latches, Catches & Bolts
C4
Flush Bolts & Coordinators
B
Pulls & Plates
•
•
•
•
•
•
•
Top Bolt with Auxiliary Fire Latch
D
• FB52 Model with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors.
FB53
Top Bolt with Auxiliary Fire Latch & Retrofit Plate
E
Stops
• FB53 Model with Auxiliary Fire Latch eliminates the bottom bolt
and includes a retrofit plate to cover existing bottom bolt prep.
UL Listed for Fire Doors.
Dimensions
Body Size: 1" Wide x 6-3/4" Long x 2" Deep
Guide Size: 1" Wide x 1-27/32" Long x 11/16" High x 3/32" Thick
Top
Bolt
Auxiliary
Fire Latch
Meets ANSI A156.3 Type 27.
UL Listed 3 Hour Fire Doors 8'0" x 10'0"
G
Miscellaneous Hardware
F
Exterior Hardware
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
C4
Ives Architectural hardware products
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3⁄4" Long x 3-1/4" Deep
Retrofit Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick
Finishes
Ives Number
US3
BHMA
605606 612 613 629630
US4
US10
US10B
US32 US32D
Constant Latching Flush Bolts –
Wood Doors
FB61T Top Bolt Only
• FB62 Model with Auxiliary Fire Latch eliminates the bottom bolt
and is UL Listed for Fire Doors..
Body Size: 1" Wide x 8-1/2" Long x 2" Deep
D
Guide Size: 1" Wide x 6" Long x 1/8" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick
Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick
Auxiliary Fire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" Deep
Auxiliary
Fire Latch
BHMA
605606 612 613 629630
US10
US10B
US32 US32D
E
US3
Stops
Meets ANSI A156.3 Type 27.
UL Listed 20 Minute Fire Doors 8'0" x 8'0"
Finishes
Ives Number
US4
Latches, Catches & Bolts
Dimensions
C5
Top Bolt with Auxiliary Fire Latch
Flush Bolts & Coordinators
FB62
Top
Bolt
B
Meets ANSI A156.3 Type 27.
UL Listed 90 Minute Fire Doors 8'0" x 8'0"
Pulls & Plates
Bottom
Bolt
A
Top
Bolt
• Constant Latching—inactive door remains latched until the
active door is opened, releasing the automatic bottom bolt and
then the top bolt can be manually released. Inactive door will
relatch automatically when door closes.
• Low Actuation Forces.
• Non-handed.
• Bolt throw is 3/4" with a 7/8" vertical adjustment.
• Bolt backset is 3/4"
DP1 or DP2 optional dust proof strike available, see page C11.
Hinges & Pivots
FB61P Top and Bottom Bolts (Pair)
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C5
Manual Flush Bolts
Hinges & Pivots
261
A
Pulls & Plates
An exceptionally smooth working flush bolt with sharp, crisp lines.
Double action spring design provides automatic holding of brass bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
Made from polished cast brass.
Bolt tip is 5/16" Diameter
Bolt throw is 3/4"
Bolt backset is 15/32"
B
Dimensions
Body Size: 3/4" Wide x 4" Long x 1-1/8" Deep
Strike Size: 5/8" Wide x 1-1/2" Long
Meets ANSI/BHMA A156.16, L04201.
Finishes
Ives Number
B3
BHMA
605609 613 619 625626
B5
B10B
B15
B26
B26D
C6
Flush Bolts & Coordinators
Flush Bolt
•
•
•
•
•
•
262
Flush Bolt
D
Latches, Catches & Bolts
•
•
•
•
•
•
An exceptionally smooth working flush bolt with sharp, crisp lines.
Double action spring design provides automatic holding of brass
bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole. Made from polished cast brass.
Bolt tip is 1/2" Diameter
Bolt throw is 1"
Bolt backset is 15/32"
E
Stops
Dimensions
Body Size: 3/4" W x 6" L x 1-11/32" D
Strike Size: 7/8" W x 1-3/4" L
G
Miscellaneous Hardware
F
Exterior Hardware
Meets ANSI/BHMA A156.16, L04201.
C6
Ives Architectural hardware products
Finishes
Ives Number
B3
BHMA
605609 613 619 625626
B5
B10B
B15
B26
B26D
Manual Flush Bolts
Meets ANSI/BHMA A156.16, L04201.
B3
BHMA
605609 613 619 625626
B5
B10B
B15
B26
B26D
C7
Finishes
Ives Number
Flush Bolts & Coordinators
Dimensions
Body Size: 3/4" W x 6" L x 1-7/16" D
Strike Size: 7/8" W x 1-3/4" L
B
A flush bolt with radiused bottom faceplate designed specifically for simple one-step router installation.
Double action spring design provides automatic holding of brass bolt in projected or retracted position, and assures ease of
operation in conjunction with deep cup finger hole.
Faceplate is polished solid brass; bolt is made from aluminum zinc alloy.
Bolt tip is 1/2" Diameter
Bolt throw is 1"
Bolt backset is 1/2"
Pulls & Plates
•
•
•
•
•
•
A
Flush Bolt
Hinges & Pivots
265
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C7
A
Hinges & Pivots
Manual Flush Bolts –
Wood Doors
Meets ANSI/BHMA A156.16, L04261.
UL Listed 90 Minute Fire Doors 8'0" x 10'0"
When the active door is opened, the lever can be moved to the
‘up’ position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the ‘down’ position, projecting the bolt into the strike and securely locking the inactive leaf.
Reduces installation costs; requires only simple router mortise
at top and bottom corners of doors.
Door strength and rigidity maintained by tying door faces to
reinforcing extensions on guide with machine screws and
bearing washers, not supplied.
Non-handed.
Bolt tip 1/2" diameter
Bolt throw is 3/4" with a 7/8" vertical adjustment.
Bolt backset is 3/4"
Not available for rabbeted door installations.
DP1 or DP2 optional dust proof strike available, see page C11.
Body Size: 1" Wide x 6-3/4" Long x 1-3/8" Deep
Guide Size: 1" Wide x 2-1/2" Long x 5/64" Thick
F
Exterior Hardware
E
Stops
D
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
G
Miscellaneous Hardware
C8
•
•
•
•
•
•
•
•
Dimensions
Latches, Catches & Bolts
C8
Flush Bolts & Coordinators
B
Pulls & Plates
FB358 Top or Bottom Bolts
Ives Architectural hardware products
Finishes
Ives Number
US3
BHMA
605606 612 613 619 625 626
US4
US10
US10B
US15
US26 US26D
Manual Flush Bolts –
Metal Doors
A
Latches, Catches & Bolts
Body Size: 1-1/4" Wide x 6-3/4" Long x 1-1/8" Deep
D
Guide Size: 1" Wide x 2" Long x 5/64" Thick
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
Finishes
Ives Number
US3
BHMA
605606 612 613 619 625 626
US10
C9
Dimensions
US4
Flush Bolts & Coordinators
DP1 or DP2 optional dust proof strike available, see page C11.
B
When the active door is opened, the lever can be moved to the
‘up’ position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the ‘down’ position, projecting the bolt into the strike and securely locking the inactive leaf.
Simplified installation in metal frames. Round bolt head requires only a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation.
Non-handed.
Bolt tip is 1/2" Diameter.
Bolt throw is 3/4" with a 7/8" vertical adjustment.
Bolt backset is 3/4"
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip. Optional rod lengths available 6", 9", 18" and 24" for fire rated doors. Optional rod lengths available 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors.
Pulls & Plates
Meets ANSI/BHMA A156.16, L04251.
UL Listed 3 Hour Fire Doors 8'0" x 10'0"
•
•
•
•
•
•
•
Hinges & Pivots
FB457 Top or Bottom Bolts
US10B
US15
US26 US26D
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C9
Hinges & Pivots
Manual Flush Bolts –
Metal Doors
A
FB458 Top or Bottom Bolts
When the active door is opened, the lever can be moved to the ‘up’ position, retracting the bolt and allowing the inactive leaf to be
opened. When the inactive leaf is closed, the lever can be moved to
the ‘down’ position, projecting the bolt into the strike and securely
locking the inactive leaf.
Simplified installation in metal frames. Round bolt head requires only
a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation.
Non-handed.
Bolt tip is 1/2" diameter.
Bolt throw is 3/4" with a 7/8" vertical adjustment.
Bolt backset is 3/4"
Standard Rod Length is 12", which is measured from the center
of the flush bolt body to the bolt tip. Optional Rod Lengths available 6", 9", 18" and 24" for fire rated Doors. Optional Rod lengths
available - 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors.
DP1 or DP2 optional dust proof strike available, see page C11.
Meets ANSI/BHMA A156.16, L04251.
UL Listed 90 Minute Fire Doors 8'0" x 10'0"
Body Size: 1" Wide x 6-3/4" Long x 1-1/8" Deep
Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
C10
Dimensions
Guide Size: 1" Wide x 2" Long x 5/64" Thick
D
Latches, Catches & Bolts
C10
Flush Bolts & Coordinators
B
Pulls & Plates
•
•
•
•
•
•
•
Ives Architectural hardware products
Finishes
Ives Number
US3
BHMA
605606609 612 613 619 625 626
US4
US5
US10
US10B
US15
US26 US26D
Dust Proof Strikes
DP1
A
Dust Proof Strikes
Designed for use with the bottom bolt of all flush bolts.
Spring-loaded plunger returns to floor or threshold level anytime
flush bolt is retracted, eliminating need to clean standard
floor strikes.
Strike hole is 3/4" Diameter and 1-1/8" Deep
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
Meets Meets ANSI/BHMA 156.16, L14011.
C11
Finishes
Ives Number
Flush Bolts & Coordinators
DP2
B
Dimensions
DP1 Face Plate: 1-7/16" Diameter
DP2 Face Plate: 1-5/8" W x 3-1/2" L x 1/8" Thick
Body: 1-3/16" Diameter x 1-7/8" Deep
Pulls & Plates
•
•
•
Hinges & Pivots
DP1
DP2
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C11
A
Hinges & Pivots
Coordinators –
Bar Coordinators and Filler Bars
B
Pulls & Plates
Meets ANSI/BHMA A156.3, Type 21A.
UL Listed for installation on labeled frame.
C12
Flush Bolts & Coordinators
For Openings Where Doors Are Same Size
Coordinator
Number
COR32
COR42
COR52
COR60
COR72
Length of Channel
For Opening
Widths
32"
42"
52"
60"
72"
34" - 52"
52" - 72"
62" - 92"
70" - 108"
84" - 132"
D
Latches, Catches & Bolts
For Openings Where Doors Are Unequal Size
COR
Series Bar Coodinators
• The COR Series Coordinators are designed for use on pairs of doors
when one door needs to close before the other.
• All COR units function easily. The active door lever, located nearest to
the active stop, holds the active door open until the trigger
mechanism is released by the closing of the inactive leaf.
• All COR units may not function correctly with swingclear hinges.
• All COR units are equipped with an adjustable override feature which
allows the active door to close under extreme pressure.
Common
•
All
COR units are compatible with Flush Bolts. Applications
• The COR Series is available in five sizes for variable door opening
Pair of 2'0" Doors
widths.
Pair of 2'6"
Doors
• The COR Series does not cover the entire length of the stop,
Pair of 3'0" Doors
so a FL filler bar can be provided to maintain architecturally clean lines.
Pair of 3'6"
Doors
• COR Series Coordinator Channels and FL fillers are made of aluminum.
Pair of 4'0"
Doors
• Optional Filler Bars: FL20 - 20", FL32 - 32" and FL44 - 44", available
to maintain clean line.
• Optional Mounting Brackets available: MB1, MB2, MB1F, MB2F,
MB3F, MB1V, MB2V, and MB3V for other stop applied hardware.
The coordinator length should equal the active door width plus
approximately 1/2 the inactive door width. The coordinator must
be 6" longer than the active door width and shorter than the overall
frame opening between stops.
FL
Finishes
Ives Finish
US28 US26D 315AN
BHMA
628713 711
Series Filler Bars
Filler Bar
Number
LengthDimensions
FL20
FL32
FL44
20"
32"
44"
Finishes
Ives Finish
US28 US26D 315AN
BHMA
628713 711
1-5/8" W x 5/8" D x 20" L
1-5/8" W x 5/8" D x 32" L
1-5/8" W x 5/8" D x 44" L
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
• The FL Filler Bars are available in three sizes for variable frame
openings.
• FL Filler Bars are made of aluminum
• FL Filler Bars are field sized to frame opening.
C12
Ives Architectural hardware products
Coordinators –
Mounting Brackets
Mounting Brackets
Jamb Depth
Stop Width
MB1
MB2
4-3/4" Min.
4-3/4" Min.
Over 2-1/2"
Up to 2-1/2"
Finishes
Ives Finish
USP
BHMA
600689 622
1-1/2" - 2-1/4"
1-1/2" - 2-1/4"
2-3/8" - 3-1/4"
2-3/8" - 3-1/4"
Over 3-3/8"
Over 3-3/8"
4" W x 3" D x 1-5/8" T
4" W x 3" D x 1-5/8" T
4"W x 4" D x 1-5/8"T
4"W x 4" D x 1-5/8"T
4"W x 3-1/2" D x 1"T
4"W x 3-1/2" D x 1"T
Finishes
Ives Finish
USP
BHMA
600689 622
E
5"
5"
5-7/8"
5-7/8"
6-7/8"
6-7/8"
Stops
MB1F
MB1V
MB2F
MB2V
MB3F
MB3V
D
Dimensions
Latches, Catches & Bolts
Stop Width
C13
Jamb Depth
Flush Bolts & Coordinators
MB3V
SPBLK
Allows for fire-rated stop mounted hardware to be properly installed
without damaging the COR Coordinators, such as fire-rated surface
vertical rod exit device strikes.
Latch will need to be lowered to compensate for the height of the
coordinator and mounting bracket.
MB-V are designed for Von Duprin 8827-F soffit latch.
Mounting brackets are made of steel.
Product
MB2V
4" W x 3" D x 15/16" T
4" W x 3-1/4" D x 1-5/8" T
Fire Rated Mounting Brackets
•
•
•
•
MB1V
SP28
Dimensions
B
Product
Pulls & Plates
MB1F, MB2F and MB3F
MB1V, MB2V and MB3V
Allows stop mounted hardware to be properly installed without
damaging the COR coordinator, such as a parallel arm closer or
a non-fire-rated surface vertical rod strike.
Stop mounted hardware will need to be lowered to compensate
for the height of the coordinator and mounting bracket.
MB mounting brackets are made of aluminum
A
•
•
•
Hinges & Pivots
MB1and MB2
SP28
SPBLK
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
C13
COR7G and COR9G
Gravity Coordinators
•
•
•
•
•
Meets ANSI/BHMA A156.3, Type
21.
•
UL Listed for Fire Doors.
•
C14
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Coordinators –
Gravity Coordinators
When active door is open, coordinator prevents active door from
closing until inactive door bypasses. Closing of inactive door causes
strike plate on top of door to contact cam and lift arm, allowing active
door to close. As inactive door continues closing, roller rides over
strike plate on to door bracket, holding arm above active door.
Non-handed.
Gravity action arm and door bracket are adjustable on the job for ease
of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage.
Nylon roller on short arm glides smoothly over door bracket
and strike, ensuring silent operation.
Made of forged brass.
COR7G for use on pairs of doors with astragal on active door up
to 4' or with astragal on inactive door up to 3'4" or with astragal on
both doors up to 2'10"
COR9G for use on pairs of doors with astragal on active over 4' or
with astragal on inactive door over 3'4" or with astragal on both doors
over 2'10"
ProductProjection
Finishes
Ives Finish
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
D
Latches, Catches & Bolts
CORG7G7"
CORG9G9"
CB1
Carry Bar
E
Stops
• Used when it is possible for the inactive door
to be opened before the active door.
• Prevents damage to the doors and other hardware.
• Nylon roller insures quiet and efficient operation.
• Non-handed.
• All-steel construction.
• Standard sex bolts for mounting.
G
Miscellaneous Hardware
F
Exterior Hardware
Meets ANSI/BHMA A156.3, Type 21.
C14
Ives Architectural hardware products
Finishes
Ives Finish
US3
BHMA
605606 612 613 625626 622600
US4
US10
US10B
US26 US26D SPBLK
USP
Ordering Guide –
Bar Coordinators
Hinges & Pivots
COR
52
A
How to Order COR and Accessories
US28
FL20
D
36"
COR Size:
32, 42, 52, 60, 72
Pulls & Plates
B
Finishes:
US28, US26D, 315AN
Filler Bar (if desired):
FL20, FL32, FL44
C15
Flush Bolts & Coordinators
Vertical Rod Exit Device Cutout Type (if applicable):
A, B, C, D, E, F, G
If other Vertical Rod Exit Device not listed on chart, from page C16,
include information as shown on page C16.
Active Door Size – Required for ALL Vertical Rod Exit Device Applications
To determine the size COR you need:
X
Y
ACTIVE DOOR
WIDTH
INACTIVE DOOR
WIDTH
D
INACTIVE LEAF
ACTIVE LEAF
W
COORDINATOR
V
F
Latches, Catches & Bolts
1. Start with the active door width (X).
2. Next consider the overall frame opening between stops (F).
3. Preferably, the coordinator would equal the active door
width (X) + approximately 1/2 inactive door width (Y).
The coordinator must be 6" longer than the active door width (X)
and less than the overall frame opening between stop (F).
STOP WIDTH
STOP THICKNESS
Examples:
F
Exterior Hardware
• 48" Active Door, 24" Inactive Door, 5/8" Stops
Active Door Size, X = 48"
Overall Frame Opening between Stops, F = 94-3/4"
Recommended Coordinator: COR60
E
• Pair of 36" Doors, 5/8" Stops
Active Door Size, X = 36"
Overall Frame Opening between Stops, F = 70-3/4"
Recommended Coordinator: COR52
• 36" Active Door, 18" Inactive door, 5/8" Stops
Active Door Size, X = 36"
Overall Frame Opening between Stops, F = 52-3/4"
Recommended Coordinator: COR42
Stops
• Pair of 30" Doors, 5/8" Stops
Active Door Size, X = 30"
Overall Frame Opening between Stops, F = 58-3/4"
Recommended Coordinator: COR42
G
Miscellaneous Hardware
Ives Architectural hardware products
C15
A
Hinges & Pivots
Coordinators
Special Factory Preparation for
Use with Vertical Rod Exit Devices
Coordinators may need to be prepared at the factory for use with
some surface or concealed vertical rod exit devices.
(See Chart below)
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C16
Flush Bolts & Coordinators
B
Pulls & Plates
If the exit device is not listed the following information is needed.
C16
1.Exit Device Manufacturer and Model No.
2.Active Door Size, “X”
3.Inactive Door Size, “Y”
4.Exit Device Backset, “U”
5. Stop Width, “W”
6.Stop Thickness if other than 5/8", “V”
Exit Device
Manufacturer
Exit Device
Number
Device
Backset
Maximum
Active Door
Coordinator Size Needed
Coordinator
Cutout Type Mounting Bracket
Needed
33"
42"
Von Duprin
5547-F
2-3/8"43" 52"
Type A None
51"
60"
63"
72"
33"
42"
MB1V, MB2V
43" 52"
or MB3V
Von Duprin
8827-F
2-3/4"
Type B
51"
60"
see page C3
63"
72"
33"
42"
Von Duprin
8847-F
2-3/8"43" 52" Type CNone
51"
60"
63"
72"
33/3547
33"
42"
Von Duprin33/3547-F 2-3/4"43" 52" Type DNone
98/9947
51"
60"
98/9947-F
64"
72"
33/3548
33"
42"
Von Duprin33/3548-F 2-3/4"43" 52" Type D None
98/9948
51"
60"
98/9948-F
64"
72"
33/3547WDC
34"
42"
Von Duprin33/3547WDC-F 1-5/16"44" 52"
Type ENone
98/9947WDC
52"
60"
98/9947WDC-F
65"
72"
17-C
F-17-C
18-C
F-18-C
33"
42"
FalconXX-C
2-3/4"43" 52" Type FNone
F-XX-C
51"
60"
24-C
63"
72"
F-24-C
25-C
F-25-C
17-C-WDC
F-17-C-WDC
18-C-WDC
F-18-C-WDC
33"
42"
FalconXX-C-WDC
2-13/16"43" 52"
Type GNone
F-XX-C-WDC
51"60"
24-C-WDC
63"72"
F-24-C-WDC
25-C-WDC
F-25-C-WDC
Ives Architectural hardware products
Surface Bolts, Latches & Catches
C
Flush Bolts & Coordinators
D1
Latches, Catches & Bolts
Roller Latch
RL30 Roller Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D8
RL32 Roller Latch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D8
RL36 Roller Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D9
RL38 Roller Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D9
RL1152 Roller Latch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
STK685 Strike Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
STK685L Strike Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10
B
Door Guards
481 Chain Door Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
482 Solid Bar Door Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D7
Pulls & Plates
Surface Bolts
page
SB360 Surface Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2
SB453 Surface Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D2
SB1600 Surface Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D3
SB1601M1 Surface Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D3
SB1601M2 Surface Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D3
40 Surface Bolt, Decorative. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D4
253 Surface Bolt, Decorative. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D5
S48 Mortise Door Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D6
054 Dutch Door Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D6
A
Hinges & Pivots
Table Of Contents
Angle Stop
AS18 Angle Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D11
AS895 Angle Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D11
E
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
Stops
Latches/Catches
CL11 Invisible Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
CL12 Invisible Latch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
CL14 Auxiliary Pusher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D12
CL21 Ball Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
CL21A Ball Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
CL22 Ball Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D13
325 Magnetic Catch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
326 Magnetic Catch, Heavy Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
327 Magnetic Catch, Heavy Duty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D14
330 Roller Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
335 Roller Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
336 Roller Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D15
345 Ball Catch, Adjustable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
347 Ball Catch, Dual Adjustable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
349 Ball Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D16
D1
Surface Bolts
Hinges & Pivots
SB360 Surface Bolt
Bar: 3/4" Wide x 3/4" Thick
Overall Width: 2-1/32"
Overall Projection: 2-1/16"
Top Strike: 1-1/2" Wide x 1-1/2" Long x 3/16" Thick
Optional Mortise Strike: 1-5/8" Wide x 3-1/2" Long x 1/8" Thick
Finishes
Ives Number
US2C
D2
BHMA603
SB453 Surface Bolt
•
•
•
•
•
•
•
•
•
Exterior Hardware
E
Stops
Surface Bolt has 1-3/16" throw for maximum security.
Strong tension springs prevent creep.
Ideal for all types of doors.
Available 8" & 12" lengths.
Units packed with standard screws for added security.
Units packed with both a universal top strike (US) and
a mortise bottom strike (MS).
Constructed of heavy duty steel.
Optional Sex Bolts available.
Optional Thru Bolts available.
F
Dimensions
Meets ANSI/BHMA A156.16 L84161
UL listed 3 hour fire door, up to 10'0"
G
Miscellaneous Hardware
D2
Surface Bolt has 1-1/4" throw for maximum security.
Jimmy-resistant design, bolt locks automatically when thrown,
can be released only be pressing knob toward door while retracting.
Ideal for all types of doors.
Available in 12" length
Unit locks in both the up and down position.
Accepts padlock (not furnished) with maximum 3/8" diameter shackle,
minimum 1-3/4" shackle opening height.
Units packed with one-way screws for added security.
Standard screws also supplied.
Units packed with both a universal top strike (US) and a mortise bottom
strike (MS).
Constructed of heavy duty steel.
Optional Sex Bolts available.
Optional Mortise Strike available.
Dimensions
Meets ANSI/BHMA A 156.16
UL listed 3 hour fire door, up to 10'0"
Miami Dade County NOA Listed
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
•
•
•
•
•
•
•
•
•
•
•
Bar: 3/4" Wide x 1/4" Thick
Overall Width: 2-1/32"
Overall Projection: 1-5/16"
Top Strike: 1-1/2" Wide x 1-1/2" Long x 3/16" Thick
Bottom Strike: 1-5/8" Wide x 3-1/2" Long x 1/8" Thick
Finishes
Ives Number
US2C
BHMA
603632 633639640652
US3
* only available in 8” bolt length.
Ives Architectural hardware products
US4*
US10
US10B US26D
Surface Bolts
Dimensions
C
Flush Bolts & Coordinators
Body: 8" Long x 7/8" Wide x 3/4" Thick,
Overall Knob or Lock Housing Projection: 1-1/2"
Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" Deep
Bottom Strike: 3" Long x 1" Wide x 1/8" Thick
SB1630 Finishes steel
Ives Number US2G US10B US26D
BHMA
604640 652
605613 626
D3
BHMA
Latches, Catches & Bolts
SB1640 Finishes brass
Ives Number US3 US10B US26D
SB1600M1
SB1600M2 Surface Bolt
F
Exterior Hardware
UL listed 3 hour fire doors up to 8'0" in height.
Standard Surface Bolt has 3-1/2" throw for maximum security and for doors with larger undercuts.
Sleek handle design.
Ideal for all types of doors.
Fully concealed mounting prevents vandalism.
Available in locking version. Unit locks in both the up and down position. Locking bolts are furnished with 2 keys in 4 keying variations.
Units packed with wood and machine screws to meet most field conditions.
Units available with either a universal top strike (T) or a flat bottom strike (B).
Constructed of heavy duty steel.
Optional sex bolts available
E
SB1600M2
•
•
•
•
•
•
•
•
•
Stops
SB1600M1
B
1640 meets ANSI/BHMA A156.16, L24161.
Pulls & Plates
1630 meets ANSI/BHMA A156.16, L84161 and UL
listed 3 hour fire doors up to 8'0" in height.
Standard Surface Bolt has 1" throw for maximum security.
Ideal for all types of doors.
Fully concealed mounting prevents vandalism.
Available in locking version. Unit locks in both the up and down
position. Locking Bolts are furnished with 2 keys in 4 keying variations.
Units packed with wood and machine screws to meet most field conditions.
Units available with either a universal top strike (T) or a flat bottom strike (B).
1630 Series is constructed of heavy duty steel.
1640 Series is constructed of brass.
Optional sex bolts available
A
•
•
•
•
•
•
•
•
•
Hinges & Pivots
SB1600Surface Bolt
Dimensions
SP4
BHMA
706 691 689695 622
SP10
SP28
SP313 SPBLK
Ives Architectural hardware products
G
Finishes
Ives Number
Miscellaneous Hardware
Bar: 11" Long x 3/4" Wide x 3/4" Thick, locking version 1-1/2" Thick
Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" Deep
Bottom Strike: 3" Long x 1" Wide x 1/8" Thick
D3
Hinges & Pivots
Decorative Surface Bolts
A
40
B
Pulls & Plates
•
•
•
•
•
•
•
•
•
Meets ANSI/BHMA A156.16
Concealed screw design enhances appearance and security.
Exceptional strength and durability provided by interlocking
construction of heavy gauge track and rod.
Permanent stop prevents rod disengagement from track.
Tension spring holds bolt in desired position.
Track assures smooth operation and interlocks with side edges of
rod to eliminate marring.
Decorative 5/8" diameter knob designed to facilitate bolt operation.
Made from extruded brass or aluminum.
Available in 3", 4" and 6" lengths.
Packed with both Universal and Mortise Strikes.
Dimensions
Throw: 15/16"
Projection: 3/4"
C
Flush Bolts & Coordinators
Decorative Surface Bolt
Width: 11/16"
Length: 3", 4" or 6"
Latches, Catches & Bolts
Finishes brass
Ives Number
B3
D4
BHMA
B10B
A15*
PA28
666670 628
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
* only available 3” bolt Schlage Carded.
D4
Ives Architectural hardware products
B15
B26
B26D
605609 613 619 625626
Finishes aluminum
Ives Number A3*
BHMA
B5
Decorative Surface Bolts
Decorative Surface Bolt
Heavy duty, decorative bolt ideal where extra strength required
Decorative 1-1/4" diameter knob fits well with any décor and
designed to facilitate bolt operation.
Made from solid brass.
Available in 8" and 12" lengths.
Packed Universal Strike (US) & Mortise Strike (MS). Pulls & Plates
B
Dimensions
Finishes
Ives Number
B3
BHMA
605613 626
B26D
C
B10B
Flush Bolts & Coordinators
Throw: 1-1/8"
Projection: 1-5/16"
Half Round Rod: 5/8"
Overall Width: 1-5/8"
Length: 8" or 12"
Meets ANSI/BHMA A156.16
A
•
•
•
•
•
Hinges & Pivots
253
D5
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
D5
Dutch Door & Mortise Door Bolts
Hinges & Pivots
054
A
B
Pulls & Plates
Practical, rugged, attractive bolt for application on dutch doors
as well as other areas.
Chamfered rod end draws the two leaves of door tightly together.
Sufficient tolerance provided in strike opening to allow for misalignment
of door leaves and also prevents binding of bolt.
Decorative 1" diameter knob designed to facilitate bolt operation.
Made from solid brass.
Packed with Standard Strike (SS), Mortise Strike (MS) and
Universal Strike (US).
Dimensions
Meets ANSI/BHMA A156.16.
Throw: 5/8"
Projection: 1-1/8"
Half Round Rod: 5/8"
Overall Width: 1-5/8"
Rod Length: 4-1/4"
Overall Length: Specify 4-3/8" (Including Knob)
Finishes
Ives Number
B3
BHMA
605606 612 613 619 625 626
B4
B10
B10B
B15
B26
D6
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Dutch Door Bolt
•
•
•
•
•
•
S48
Meets ANSI/BHMA A156.16.
G
Ives Architectural hardware products
1-3/4"
1/2"
1/2"
2-1/2" Long x 9/16" diameter
1-3/4" High x 7/8" Wide
Finishes brass
Ives Number
B3
BHMA
F
Exterior Hardware
E
Stops
Dimensions
Backset: Bolt Throw: Bolt Diameter: Case: Strike: Miscellaneous Hardware
D6
Mortise Door Bolt
• Brass oval turn knob and escutcheon.
• Steel bolt for extra strength. Rack is milled for precision fit with pinion.
B5
B10B
B15
B26
B26D
605609 613 619 625626
B26D
Door Guards
Chain Door Guard
B
Dimensions
Door Plate: 3-3/8" Long x 1-7/16" Wide
Chain Holder: 1-10/16" High x 3/4" Wide
Chain Length: 4-3/4"
605626
Finishes steel
Ives Number
F3
BHMA
F4
F5
F10
F15
F26
F26D
F716
632633 638639646651 652
482A Cast Aluminum Dimensions
Strike Plate: 2-1/2" High x 7/8" Wide
Holder: 1-3/4" High x 1-1/16" Wide
Holder: 2-1/2" High x 15/16" Wide
Arm Length: 4-3/4"
Arm Length: 3-13/16"
Edge Guard: 1-1/8" High x 1-1/32" Wide
B10B
B15
B26
B26D
605606 612 613 619 625 626
G
Finishes aluminum
Ives Number
A3
BHMA
B10
Miscellaneous Hardware
BHMA
B4
F
Strike Plate: 2-5/8" High x 1-1/32" Wide
Exterior Hardware
Finishes brass
Ives Number
B3
E
482B Cast Brass Dimensions
Stops
For use on doors that are flush with frames.
The solid bar, interlocking with the ball on the strike plate,
permits the door to be slightly opened to allow viewing.
The hinged bar allows the door guard to be positioned 180° away
from the door when not in use.
Edge guard only, furnished with cast brass door guards,
minimizes the chance for marring the door or frame.
Strike plate is designed to prevent the solid bar from marring the
inside of the door when in use.
Made from cast brass or cast aluminum. Packed with sheet metal screws.
Shims available in US26D (626) only, 1/8” or 3/8”. Only fits 482B.
D7
Solid Bar Door Guard
•
•
•
•
•
•
•
•
Latches, Catches & Bolts
482
Meets ANSI/BHMA A156.16
C
BHMA
B26D
Flush Bolts & Coordinators
Finishes brass
Ives Number
B3
Pulls & Plates
Meets ANSI/BHMA A156.16
Permits the door to be slightly opened to allow viewing.
Narrow chain holder maintains chain in stationary position when
door guard is not in use, eliminating marring of door and
frame caused by dangling chain.
Welded twist link steel chain finished to match door plate
and chain holder.
Made from wrought brass or burnished wrought steel.
Packed with sheet metal screws.
A
•
•
•
•
•
Hinges & Pivots
481
A5
A26
A26D
666 672702
Ives Architectural hardware products
D7
Roller Latches
Hinges & Pivots
RL30
A
B
Pulls & Plates
Dimensions
Body: 1" Wide x 3-3/8" High x 1-11/16" Deep
Strike: 1-11/16" Wide x 2-1/4" High x 5/32" Thick, Lip to Center- 1-5/16"
Optional ASA Strike: 1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to Center- 1-1/4"
BHMA
Latches, Catches & Bolts
RL32
D8
Meets ANSI/BHMA A156.16, E19091
F
US10B
US26 US26D
Actuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed.
The projection of the roller is easily adjusted by turning knurled
knob on back of latch.
Maximum projection of the roller is 1/2" allowing for variance in
the door clearance.
Fits heavy-duty cylindrical lock cutout.
Nylon Roller Standard.
Non-handed.
Brass Construction.
Optional Strike—A—ASA.
Dimensions
Body: 1-1/8" Wide x 2-1/4" High x 2-1/4" Deep
Strike: 1-1/8" Wide x 2-3/4" High x 3/32" Thick, Lip to Center- 1-1/4"
Optional ASA Strike: 1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to Center- 1-1/4"
BHMA
G
US10
Roller Latch
Finishes brass
Ives Number US3
Ives Architectural hardware products
US4
605606 612 613 625626
•
•
•
•
•
•
•
•
Exterior Hardware
E
Stops
Actuation is simple, closing of the door causes the roller to fall in the
depression of the strike, thereby holding the door closed.
The projection of the roller is easily adjusted using adjusting screws on the face of the unit.
Maximum projection of the roller is 3/8" allowing for variance in
the door clearance.
Nylon Roller Standard.
Forged Brass Construction.
Optional Strike—A—ASA.
Optional— F — Brass Roller, must be ordered separately.
Finishes brass
Ives Number US3
C
Flush Bolts & Coordinators
Meets ANSI/BHMA A156.16, E19091
Miscellaneous Hardware
D8
Roller Latch
•
•
•
•
•
•
•
US4
US10
US10B
US26 US26D
605606 612 613 625626
Roller Latches
Roller Latch
C
BHMA630
Roller Latch
Meets ANSI/BHMA A156.16, L27092
Actuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed.
The projection of the roller is easily adjusted by turning slotted screw.
Maximum projection of the roller is 3/8" allowing for variance in the
door clearance.
Nylon Roller.
Non-handed.
Stainless Steel Construction.
E
Stops
Dimensions
Body: 1-3/8" Wide x 2" High x 7/8" Deep
Strike: 1" Wide x 2-1/8" High x 3/8" Deep
D9
•
•
•
•
•
•
Latches, Catches & Bolts
RL38
Flush Bolts & Coordinators
Finishes Stainless Steel
Ives Number US32D
B
Dimensions
Body: 1" Wide x 2-1/4" High x 2" Deep
Strike: 1-1/8" Wide x 2-3/4" High x 3/32" Thick, Lip to Center- 1-1/4"
Optional ASA Strike: 1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to Center- 1-1/4"
Pulls & Plates
Meets ANSI/BHMA A156.16, L57082
Actuation is simple, closing of the door causes the roller to fall in
the depression of the strike, thereby holding the door closed.
The projection of the roller is easily adjusted by turning slotted
screw on back of latch.
Maximum projection of the roller is 5/16" allowing for variance
in the door clearance.
Fits cylindrical lock cutout.
Nylon Roller.
Non-handed.
Stainless Steel Construction.
Optional Strike–A—ASA.
A
•
•
•
•
•
•
•
•
Hinges & Pivots
RL36
Finishes Stainless Steel
Ives Number US32D
F
Exterior Hardware
BHMA630
G
Miscellaneous Hardware
Ives Architectural hardware products
D9
Hinges & Pivots
Roller Latches
A
RL1152
B
Pulls & Plates
Combination of RL30 Roller Latch and Angle Stop.
Actuation is simple, closing of the door causes the roller to
fall in the depression of the strike, thereby holding the
door closed.
The projection of the roller is easily adjustable using
adjusting screws on the face of the unit.
Maximum projection of the roller is 3/8" allowing for
variance in the door clearance.
Nylon Roller Standard.
Forged Brass Construction.
Optional— F — Brass Roller, must be ordered separately.
Dimensions
Body: 1-1/2" Wide x 4-1/2" High x 1-3/4" Deep with 3/4" Angle
Strike: 1-1/8" Wide x 2-1/4" High x 5/32" Thick
Meets ANSI/BHMA A156.16, E19111
C
Flush Bolts & Coordinators
Roller Latch
•
•
•
•
•
•
•
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
685 A&B Dim. Variable
D10
Latches, Catches & Bolts
Optional Strike
STK685
3/32"
1-11/16"
E
Stops
A
685L
Strike
•
•
•
•
Custom make strike for doors that swing both directions.
For use with roller latches.
Constructed of 3/32" brass.
Dimple of strike centered on strike.
Specify frame depth - A. Overall strike length will be
A + 3/8” to accommodate 3/16” lip on each side
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
1-5/32"
STK685L
F
Exterior Hardware
2-1/4"
A
G
Miscellaneous Hardware
B
D10
• Custom make strike for doors that swing both directions.
For use with roller latches.
• Constructed of 3/32" brass.
• Location of strike dimple is variable.
Please specify frame depth - A and location of dimple
from edge of frame - B. Dimple will be located B + 3/16"
to accommodate lip.
• Specify frame depth - A. Overall strike length will be
A + 3/8” to accommodate 3/16” lip on each side
Finishes
Ives Number US3
US4
US10 US10B US26 US26D
BHMA
Ives Architectural hardware products
Strike
605606 612 613 625626
Angle Stops
• Surface applied stop for single doors.
• Large rubber bumper to ensure quiet operation.
• Constructed of 1/8" Brass Angle.
A
Hinges & Pivots
AS895 Angle Stop
Dimensions
1-1/2" Wide x 1" Angle x 2-1/2" Long
BHMA
605606 612 613 625626
US10
US10B
US26 US26D
Surface applied stop for single and double doors.
Includes SR64 door silencers to ensure quiet operation.
SR64 silencers are replaceable.
Constructed of 3/16" Brass Angle.
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
D11
Finishes
Ives Number
Latches, Catches & Bolts
Dimensions
1-1/2" Wide x 3/4" Angle x 3-1/2" Long
C
Angle Stop
•
•
•
Flush Bolts & Coordinators
AS18
US4
B
US3
Pulls & Plates
Finishes
Ives Number
E
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
D11
Invisible Latches
Hinges & Pivots
CL11
A
Meets ANSI/BHMA 156.9, B03272
B
Pulls & Plates
Invisible Latch
•
•
•
•
•
•
•
Invisible latch is ideal for installations where no visible latch is desired.
Unit can be installed at the top, bottom or side of the door.
Can be mortised into the stop or surface mounted to the stop.
Recommended for use on small panels, cabinet doors or light weight
closet doors.
Operation is simple, latching is accomplished by a slight push.
To unlatch the door, a harder push releases the door and pushes the
door out.
Brass and plastic construction.
Applies 13 pounds to open the door.
Finishes
Ives Number
US3
BHMA
605606 612 626
US4
US10 US26D
C
Flush Bolts & Coordinators
Dimensions
Body: 1-1/4" Wide x 1-7/8" High x 7/16" Thick
Strike: 9/16" Wide x 1-5/16" High x 9/16" High
CL12
D12
Latches, Catches & Bolts
•
•
•
•
•
•
•
Exterior Hardware
E
Stops
Meets ANSI/BHMA A156.9, B03272
Finishes
Ives Number
US3
US4
BHMA
605
606
F
Ives Architectural hardware products
US10 US26D
612
626
Auxiliary Pusher
•
•
•
•
•
Meets ANSI/BHMA A156.9, B13282
Invisible latch is ideal for installations where no visible latch is desired.
Unit can be installed at the top, bottom or side of the door.
Can be mortised into the stop or surface mounted to the stop.
Recommended for use on larger panels or regular size doors.
Operation is simple, latching is accomplished by a slight push.
To unlatch the door, a harder push releases the door and pushes the
door out.
Brass and plastic construction.
Applies 27 pounds to open the door.
Dimensions
Body:
1-1/4" Wide x 2-1/4" High x 9/16" Thick
Strike: 5/8" Wide x 1-13/16" High x 9/16" Projection
CL14
G
Miscellaneous Hardware
D12
Invisible Latch
Aid in the operation of the CL11 and CL12 where hinges or
surrounding conditions prevent smooth operation of doors.
Provides 1-1/16" throw.
Nylon pusher.
Brass construction.
Applies 10 pounds to open the door.
Dimensions
Body: 2-15/16" Long x 1-11/16" Wide x 5/8" Deep
Finishes
Ives Number
US3
BHMA
605606 612 626
US4
US10 US26D
Ball Catches
Ball Catch
Dimensions
Body: 3/4" Wide x 3" High x 3/4" Deep
Strike: 3/4" Wide Hex x 1-1/2" High
B
Pulls & Plates
Meets ANSI/BHMA A156.9
Four-way catch with hexagon stud.
Ideal for holding medium duty doors.
The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
Strike can enter body from any direction.
Spring tension is easily adjusted to suit field conditions.
Body can be surface applied or mortised.
Brass construction.
Finishes brass
Ives Number US26D
Finishes brass
Ives Number US3
US10
US26
US26D
Ball Catch
G
Finishes brass
Ives Number US3
Miscellaneous Hardware
Dimensions
Body: 1/2" Wide x 2-3/16" High x 1/2" Deep
Strike: 3/8" Wide x 1-3/8" High x 5/8" Deep
F
Three-way catch with plate type strike.
Ideal for smaller cabinet doors or panels.
The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
Strike can enter body from either side or front.
Spring tension is easily adjusted to suit field conditions.
Body can be surface applied or mortised.
Brass construction.
Exterior Hardware
•
•
•
•
•
•
•
BHMA
E
605606 612 625 626
Stops
CL22
US4
D13
Dimensions
Body: 3/4" Wide x 3" High x 3/4" Deep
Strike: 7/16" Wide x 1-3/4" High x 7/8" Deep
BHMA
Meets ANSI/BHMA 156.9, B13302.
Four-way catch with plate type strike.
Ideal for closet doors, access doors, hinged openings and numerous
other applications.
The strike slides between two stainless steel balls that are under
spring tension. As the strike engages, the door is held tightly shut.
Strike can enter body from any direction.
Spring tension is easily adjusted to suit field conditions.
Body can be surface applied or mortised.
Brass construction.
Latches, Catches & Bolts
Meets ANSI/BHMA A156.9, B13292
C
CL21A Ball Catch
Flush Bolts & Coordinators
BHMA626
•
•
•
•
•
•
•
A
•
•
•
•
•
•
•
Hinges & Pivots
CL21
US4
US10
US26
US26D
605606 612 625 626
Ives Architectural hardware products
D13
Hinges & Pivots
Magnetic Catches
Magnetic Catch
• Double pole.
• Self aligning magnet insures maximum pull.
• Case design allows easy magnet adjustment on cabinet
or small door applications.
• Aluminum case.
• Packed with sheet metal screws.
• 5 lbs. Load Capacity
Meets ANSI/BHMA A156.9 B43171.
Dimensions
Case: 1-1/8" wide x 2-1/16" Long x 5/8" Thick
Finishes aluminum
Ives Number
A3
BHMA
A92
666673
D14
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
325
326
Mighty-Mite® Heavy Duty Magnetic Catch
Meets ANSI/BHMA A156.9 B43161.
• Dual double pole.
• Self-aligning magnets insure maximum pull.
• Can be surface mounted or mortised.
• Aluminum case.
• Packed with sheet metal screws, 2 short strikes and
1 long strike.
• 9 lbs. Load Capacity
Dimensions
Case: 1" Wide x 3-1/8" Long x 9/16" Thick
Finishes aluminum
Ives Number
A3
666673
E
Stops
BHMA
A92
327
• Dual triple pole.
• Self-aligning magnets insure maximum pull.
• Can be surface mounted or mortised.
• Aluminum case.
• Packed with sheet metal screws, 2 short strikes and
1 long strike.
• 14 lbs. Load Capacity
F
Exterior Hardware
Meets ANSI/BHMA A156.9 B43161.
D14
Dimensions
Case: 1" Wide x 3-1/8" Long x 3/4" Thick
Finishes aluminum
Ives Number
A3
G
Miscellaneous Hardware
Super-Mite® Heavy Duty Magnetic Catch
BHMA
Ives Architectural hardware products
A92
666673
Roller Catches
•
•
•
•
•
Independent rollers allow positive action and self-alignment.
Cushioned rollers absorb shock and noise, hold door away from cabinet.
Application allows for easy adjustment.
Made from wrought steel.
Packed with screws and brads.
B
Pulls & Plates
Dimensions
Case:
1-1/4" High x 11/16" Wide
Strike: 1-1/4" High x 3/8" Wide
A
Roller Catch
Hinges & Pivots
Meets ANSI/BHMA A156.9 B83071.
330
Finishes
Ives Number
F2C
BHMA603
Roller Catch
D15
Dimensions
Face Plate: 7/8" Wide x 2-1/4" High
Bore: 1-3/4" Deep x 13/16" Diameter
Strike: 1-5/8" Wide x 2-1/4" High, Lip to center- 1-3/16"
Finishes
Ives Number
B3
BHMA
605609 612 613 619 625 626
B5
B10
B10B
B15
Latches, Catches & Bolts
Meets ANSI/BHMA A156.16 L27081 for brass
and L87081 for steel.
Smooth, positive latching action insured by powerful conical spring.
Durable nylon roller insures quiet operation.
Adjustable tension. Adjustments can be varied from 4 to 17 lbs.
of holding power making possible a wide range of door performance.
Easily installed on thin doors.
Full lip style strike designed for simplified mortising.
Made from wrought brass or wrought steel.
Packed with sheet metal screws.
C
•
•
•
•
•
•
•
Flush Bolts & Coordinators
335
B26
B26D
E
Stops
336
Roller Catch
B3
BHMA
605606609 612 613 619 625 626
B4
B5
B10
B10B
B15
B26
B26D
Ives Architectural hardware products
G
Meets ANSI/BHMA A156.16 L27081 for brass
and L87801 for steel.
Finishes
Ives Number
Miscellaneous Hardware
Dimensions
Face Plate: 7/8" Wide x 2-1/4" High
Bore: 13/16" Diameter x 1-3/4" Deep
Strike: 7/8" Wide x 2-1/4" High, Lip to center- 1-1/8"
F
Smooth, positive latching action insured by powerful conical spring.
Durable nylon roller insures quiet operation.
Adjustable tension. Adjustments can be varied from 4 to 17 lbs.
of holding power making possible a wide range of door performance.
Easily installed on thin doors.
Standard box type strike designed for neat appearance.
Made from wrought brass or wrought steel.
Packed with sheet metal screws.
Exterior Hardware
•
•
•
•
•
•
•
D15
345
Adjustable Ball Catch
•
•
•
•
•
Finishes brass
Ives Number
B3
Meets ANSI/BHMA A156.9 B23013.
C
Flush Bolts & Coordinators
BHMA
B5
B10
B10B
B15
B26
B26D
605609 612 613 619 625 626
347
Dual Adjustable Ball Catch
• For catch in door installations.
• Dual adjustment for door clearance and holding strength.
• Lip strike is designed for use where strike is mounted in jamb.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door clearances.
• Adjustable spring tension.
• Made from wrought brass.
Dimensions
D16
Latches, Catches & Bolts
Ideal for cabinets and small interior doors.
Free rolling ball insures smooth, positive and trouble-free action.
Adjustable threaded barrel compensates for various door clearances.
Adjustable spring tension.
Made from wrought brass.
Dimensions
Face Plate: 3/4" Wide x 1-1/2" High
Bore: 1" Deep x 9/16" Diameter
Strike: 25/32" Wide x 1-1/2" High, Lip to center- 13/32"
B
Pulls & Plates
A
Hinges & Pivots
Ball
Catches
Face Plate: 1" Wide x 2-1/8" High
Bore: 7/8" Diameter x 1-3/8" Deep
Strike: 1-3/8" Wide x 2-1/8" High, Lip to center- 7/8"
Meets ANSI/BHMA A156.9 B23013.
Finishes brass
Ives Number
B3
B5
B10
B10B
B15
B26
B26D
605606609 612 613 619 625 626
G
Miscellaneous Hardware
F
Exterior Hardware
E
Stops
BHMA
B4
D16
349
Ball Catch
• For catch in door installations.
• Radiused corners allow easy installation with a router.
• Dual adjustment for door clearance and holding strength.
• Lip strike is designed for use where strike is mounted in jamb.
• Free rolling ball insures smooth, positive and trouble-free action.
• Adjustable threaded barrel compensates for various door clearances.
• Adjustable spring tension.
• Made from wrought brass.
Dimensions
Face Plate: 1" Wide x 2-1/8" High
Bore: 7/8" Diameter x 1-3/8" Deep
Strike: 1-3/8" Wide x 2-1/8" High, Lip to center- 7/8"
Meets ANSI/BHMA A156.9 B23013.
Finishes brass
Ives Number
B3
BHMA
Ives Architectural hardware products
B4
B5
B10
B10B
B15
B26
B26D
605606609 612 613 619 625 626
B716
Door Stops
Hinges & Pivots
Table Of Contents
A
Floor Stops
page
FS13 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
R14 Riser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
FS17 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E2
FS436 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
FS438 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
R435 Riser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
R437 Riser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E3
FS439 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS410 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4
FS18, FS18L Floor Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
FS434 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
430 Floor Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5
FS441, FS441WS Floor Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
FS444, FS448 Floor Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6
B
Pulls & Plates
C
Flush Bolts & Coordinators
Floor Stop & Holder
FS9 Floor Stop & Semi-automatic Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E7
FS40, FS41, FS42, FS43 Floor Stop & Automatic Holder. . . . . . . . . . . . . . . . . E7
FS446, FS450 Floor Stop & Manual Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . E8
FS495, FS496, FS497 Floor Stop & Automatic Holder . . . . . . . . . . . . . . . . . E8
D
Latches, Catches & Bolts
Wall Bumpers/Stops
WS11, WS11X Wall Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
WS20, WS20X Manual Wall Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9
WS33, WS33X Wall Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E10
WS65 Wall Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E10
WS401, WS402 Wall Bumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E11
WS404 Wall Bumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E11
WS406, WS407 Wall Bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E12
411R Wall Bumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E13
WS443, WS447 Wall Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E14
WS445, WS449 Manual Wall Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E14
Wall Holders
WS40 Automatic Wall Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
WS45, WS45X Automatic Wall Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15
E1
Stops
Kick Down Holder
FS452 Kick Down Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E16
FS455 Kick Down Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E16
FS544, FS555 Kick Down Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E17
Exterior Hardware
Plunger Door Holders
FS1153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18
FS1154. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18
F
Roller Bumpers
RB470, RB471, RB472 Roller Bumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19
Miscellaneous Hardware
Residential Door stops
060, 061 Flexible Door Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
60, 61 Door Base Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20
63 Flexible Door Stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
64 Door Base Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
Silencers
SR64, SR65, SR66 Door Silencer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23
Ives Architectural hardware products
G
Hinge Pin Stops
69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E21
70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
72Z Residential Door Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
73Z Commercial Door Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22
E1
Hinges & Pivots
Floor Stops — Dome
FS13
A
•
•
•
•
•
Meets ANSI/BHMA 156.6, L12141.
Standard FS13 for use where no threshold is used.
Heavy-Duty Cast Dome Stops constructed of brass.
Unique riser design of R14 (below) allows easy conversion to
threshold application.
Units are packed with fasteners sufficient for mounting in all types of
floor construction, including concrete.
Replaceable grey rubber bumper.
Dimensions
Overall Height: 1”
Base Height: 5/32”
Base Diameter: 1-3/4”
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
Dome Stop
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
R14
Dome Stop Rise
• Adapts the FS13 Dome Stop to threshold use.
• Brass Die Cast Construction.
Dimensions
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
E2
Stops
D
Riser Height: 5/16”
Base Diameter: 1-3/4” round
One piece dome stop for use with thresholds.
Heavy-Duty Cast Dome Stops constructed of brass.
Units are packed with fasteners sufficient for mounting in all types of
floor construction, including concrete.
Replaceable grey rubber bumper.
Dimensions
Meets ANSI/BHMA 156.6, L12161.
G
Miscellaneous Hardware
E2
Dome Stop
•
•
•
•
F
Exterior Hardware
FS17
Ives Architectural hardware products
Overall Height: 1-11/32”
Base Height: 1/2”
Base Diameter: 1-3/4” round
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
Floor Stops — Dome
A
Hinges & Pivots
FS436 Dome Stop
FS438 Dome Stop
FS436
Meets ANSI/BHMA 156.16, L12141 for brass
or bronze and L32141 for aluminum.
Dimensions
FS438
Overall Height: 1-3/8”
Base Height: 9/16”
Base Diameter: 1-3/4” x 2” Oval
BHMA
US4
US5
US10
US10B
US15
US26 US26D
B716
605606609 612 613 619 625 626
D
Finishes aluminum
Ives Number US28
BHMA
Latches, Catches & Bolts
Finishes brass
Ives Number US3
C
FS438
Meets ANSI/BHMA 156.16, L12141 for brass
or bronze and L32141 for aluminum.
Flush Bolts & Coordinators
FS436
Overall Height: 1”
Base Height: 3/16”
Base Diameter: 1-3/4” x 2” Oval
B
• FS436 for doors without threshold.
• FS438 for doors with threshold or undercut doors.
• Heavy-Duty Cast Dome Stops constructed of brass, bronze or aluminum.
• Packed with wood screw and plastic anchor.
Replaceable gray, non-marring rubber bumper.
Pulls & Plates
628
Extruded aluminum, mill finish.
R435 for conversion of FS436 Dome Stop to carpet installation.
R437 For conversion of FS438 Dome Stop to carpet installation.
Packed with wood screws, lead shield and stud.
Specify Tampin (TPN) if required.
F
Exterior Hardware
•
•
•
•
E3
Riser for FS436 Dome Stop
Riser for FS438 Dome Stop
Stops
R435
R437
Dimensions
Available in 1/4”, 3/8”, 1/2”, 5/8”, 3/4” and 1” height.
1"
Miscellaneous Hardware
1-7/16"
G
1" OR
LESS
PAD
FLOOR
Ives Architectural hardware products
E3
A
Hinges & Pivots
Floor Stops
FS439 Universal Dome Floor Stop
•
•
•
•
High or Low-Rise Mount
Zinc or Stainless Steel
Spring-loaded Rubber Contact
Replaceable Rubber Bumper
Overall Height: 1-1/2”
Pad Height: 1-1/8”
Base Height: 1/4”
Base Diameter: 1-7/8”
US3
BHMA
677678 704682630
US4
• Non-directional
• Cast Brass Construction
• Replaceable Rubber Bumper
Dimensions
Overall Height: 1-1/2”
Bumper Thickness: 1/4”
Diameter: 1-1/4”
E4
Stops
F
Exterior Hardware
G
Miscellaneous Hardware
E4
Finishes
Ives Number
FS410 Decorative Floor Stop
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
Dimensions
Ives Architectural hardware products
Finishes
Ives Number
US3
BHMA
605626
US26D
US10B US26D US32D
Floor Stops
Dimensions
FS18S Height: 1-1/2” B
Security Door Stops designed for use in high vandalism areas.
Molded from black flame resistant, resilient material around a
heavy-duty stud.
Once grouted in concrete, leaves no exposed fasteners to be
tampered with or removed.
Ideal for jail or security cell areas where floor mounted stops are required.
FS18L also ideal for concrete wall applications.
Pulls & Plates
FS18L
A
FS18S
•
•
•
•
•
Hinges & Pivots
FS18S
FS18L Floor Stops
FS18L Height: 3-1/2”
FS18L Diameter: 2”
FS18S Stud Length: 2-1/2”
FS18L Stud Length: 2-1/2”
C
Flush Bolts & Coordinators
FS18S Diameter: 2”
FS434 Floor Stop
•
•
•
•
Burnished wrought steel.
For undercut doors up to 1-1/2”.
Packed with screws and plastic anchors.
Replaceable soft, resilient gray rubber.
Latches, Catches & Bolts
D
Dimensions
Overall Height: 2-5/8”
Base Size: 1-1/2” W x 2-3/4” L
Finishes
Ives Number
USC
BHMA604
•
•
•
•
Burnished wrought steel.
For undercut doors up to 1-1/2”.
Packed with screws and plastic anchors.
Replaceable soft, resilient gray rubber.
Exterior Hardware
E5
Floor Door Stop
Stops
430
F
Dimensions
Overall Height: 1-5/16”
Base Diameter: 1-1/4”
BHMA
B5
B10B
B15
B26
B26D
605606609 613 619 625 626
A5
A14
G
Finishes aluminum
Ives Number A3*
BHMA
B4
Miscellaneous Hardware
Finishes brass
Ives Number
B3
A92
666 669673
* only available in Slim-Pak of 25
Ives Architectural hardware products
E5
Floor Stops
A
Hinges & Pivots
FS441 Floor Stop
Pulls & Plates
Dimensions
Flush Bolts & Coordinators
Meets ANSI/BHMA 156.16, L12131 for brass
• Accommodates door undercut up to 1-1/2”.
• Designed to blend well with all types of construction and
provide a minimum of hindrance to cleaning efforts.
• Heavy-Duty cast brass or aluminum construction.
• Replaceable Non-marring rubber bumper.
FS441 packed with expansion shield and tampin for masonry type mounting,
and wood screws for drywall mounting.
Finishes brass
Ives Number US3
B
Overall Height: 2-1/8”
Overall Length: 2-7/8”
Base Depth: 1-5/8”
C
BHMA
Latches, Catches & Bolts
D
E6
Stops
US5
US10
US10B
US15
US26 US26D
605606609 612 613 619 625 626
FS444 Floor Stop
FS448 Floor Stop
• Ideal for interior or exterior use.
• Cast brass construction.
• Accommodates door undercut up to 2-1/2”.
• Replaceable Non-marring rubber tip.
FS444 is packed with expansion shield and lead shield, for masonry type mounting.
FS448 is packed with wood screws, for drywall mounting.
FS444
Meets ANSI/BHMA 156.16, L12131 for brass
Dimensions
FS448
Meets ANSI/BHMA 156.16,
L12121 for brass and L32121 for aluminum
Base Diameter: 2-1/2”
Overall Height: 3”
Finishes brass
Ives Number US3
F
Exterior Hardware
BHMA
BHMA628
* not available on FS444
G
Ives Architectural hardware products
US4
US5*
US10
US10B
US15
US26 US26D
605606609 612 613 619 625 626
Finishes aluminum
Ives Number US28*
Miscellaneous Hardware
E6
US4
Floor Stops
FS9
Pulls & Plates
Meets ANSI/BHMA 156.16, L11241.
Semi-automatic floor-mounted holders accommodates with door to floor clearance of 1-1/2” or less.
Cast from heavy-duty brass.
Activate holder by flipping the engagement tongue forward. When
door is opened, the hook (mounted on door) engages the tongue.
To release, push firmly on door to disengage tongue.
Universal screw pack accommodates all types of floor and
door construction.
A
•
•
•
•
Hinges & Pivots
Floor Stop & Semi-Automatic Holder
B
Dimensions
Overall Height: 3-1/2
Base Dimensions: 2” wide x 3-1/2” long
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US10B
C
CLEARANCE
FROM 9/16 to 1-1/16
1/2” or less
9/16” to 1-1/16”
1-1/8” to 1-9/16”
1-5/8” to 2-1/16”
E7
FS40
FS41
FS42
FS43
Stops
Door to Floor Clearance: D
1-3/4”
Latches, Catches & Bolts
Automatic door holders ideal for heavy-traffic situations that require
a simple, fool-proof, Hold-Open device.
Forged from brass.
Unit is activated automatically when door is opened.
A firm pull on door releases the mechanism.
Strikes accommodate different door to floor clearances.
Model numbers are determined by strike/door-to-floor clearances.
Holder position on door is adjustable.
Universal screw pack allows for installation in all types of door construction.
Dimensions
1/8” CLEARANCE
US26 US26D
Floor Stop & Automatic Holder
•
•
•
•
•
•
•
Meets ANSI/BHMA 156.16, L11301
US10
Flush Bolts & Coordinators
FS40
FS41
FS42
FS43
US4
Holder Dimensions: 3” Wide x 3-11/16” High
BHMA
1-3/4”
US10
US10B
US26 US26D
2-1/4”
605606 612 613 625626
CLEARANCE
FROM 1-1/8 to 1-9/16
CLEARANCE
FROM 9/16 to 1-1/16
1-3/16”
F
1/2”
US4
Exterior Hardware
Finishes brass
Ives Number US3
SIDE VIEW BODY
F40 MAX. DOOR
CLEARANCE
FS41
2-1/4”
CLEARANCE
FROM 1-1/8 to 1-9/16
FS42
CLEARANCE
FROM 1-5/8 to 2-1/16
2-3/4”
FS43
Ives Architectural hardware products
E7
G
CLEARANCE
FROM 9/16 to 1-1/16
Miscellaneous Hardware
1-3/4”
Floor Stops
FS446
Meets ANSI/BHMA 156.16, L11371 for brass
and L31371 for aluminum.
FS450
Meets ANSI/BHMA 156.16, L11361 for brass
and L31371 for aluminum.
FS446 packed with expansion shield and lead shield, for masonry type mounting
FS450 packed with 3 wood screws, for drywall mounting.
Dimensions
C
Stop Diameter: 1-1/16”
Base Diameter: 2-1/12”
Finishes brass
Ives Number US3
Latches, Catches & Bolts
BHMA
US4
US10
US10B
US15
US26 US26D
605606 612 613 619 625 626
D
Finishes aluminum
Ives Number US28
BHMA628
E8
Stops
FS495 Wall Stop & Automatic Holder
FS496 Floor Stop & Automatic Holder
FS497 Floor Stop & Automatic Holder
FS495 Meets ANSI/BHMA 156.16, L11291 for brass
FS496 Meets ANSI/BHMA 156.16, L11301 for brass
FS497 Meets ANSI/BHMA 156.16, L11301 for brass
•
•
•
•
•
Automatic door holders ideal for heavy-traffic situations that require a simple,
Hold-Open device.
Cast brass construction.
Recommended installation is holder on door and strike on wall.
Holder position on door is adjustable.
Holder is tapered to prevent “child riding.”
Dimensions
F
Exterior Hardware
Manual type floor holder ideal for interior or exterior use.
Cast brass or aluminum construction.
Accommodates door undercut up to 2-1/2”.
Replaceable non-marring rubber tip.
Unit functions as a stop but serves as a Hold-Open device when
hook is manually engaged in strike. Unit requires manual
disengagement to release Hold-Open.
Height from Floor to Stop Center Line: 2-5/8”
FS495 shown
FS495
Holds door 3-3/4” from wall.
FS496
Door to Floor Clearances 3/8” Maximum.
FS497
Door to Floor Clearances 1” Maximum.
Finishes brass
Ives Number US3
Miscellaneous Hardware
BHMA
G
E8
•
•
•
•
•
Overall Height: 3-3/4
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
FS446 Floor Stop & Manual Door Holder
FS450 Floor Stop & Manual Door Holder
US4*
US10B
US26 US26D
605606 612 613 625626
* not available on FS496, FS497.
Ives Architectural hardware products
US10
Wall Stops
WS11
Meets ANSI/BHMA 156.16, L12011
WS11 is furnished with wood screws for drywall mounting.
WS11X is furnished with a threaded stud and expansion shield for
masonry type mounting.
B
Pulls & Plates
WS11X
Meets ANSI/BHMA 156.16, L12021
Constructed in heavy duty cast brass.
Hexagon section on unit aids in fastening unit when expansion shield is used.
Replaceable rubber bumpers features off-set shoulder and threaded shank
that screws into body of unit.
A
•
•
•
Hinges & Pivots
WS11
WS11X Wall Stops
Dimensions
Base Diameter: 2”
Overall Projection: 3-3/4”
BHMA
US4
US10
US10B
US26 US26D
605606 612 613 625626
C
Flush Bolts & Coordinators
Finishes brass
Ives Number US3
E9
WS20X
Meets ANSI/BHMA 156.16, L11351 for brass
and L31351 for aluminum
WS20 is furnished wood screws for drywall mounting.
WS20X is furnished with threaded stud and expansion shield
for masonry type mounting.
Stops
WS20
Meets ANSI/BHMA 156.16, L11341for brass
and L32341 for aluminum
Constructed in cast brass or aluminum.
Replaceable rubber bumpers feature off-set shoulder and threaded
shank that screws into body of holder.
Hinged strike furnished matches body material and finish.
D
•
•
•
Latches, Catches & Bolts
WS20
WS20XManual Wall Holders
Dimensions
Base Diameter: 2-3/8”
Overall Projection: 4”
Strike Height: 2”
BHMA
US4
US10
US10B
US26 US26D
605606 612 613 625626
Finishes aluminum
Ives Number US28
F
Finishes brass
Ives Number US3
Exterior Hardware
Strike Width: 1”
Miscellaneous Hardware
BHMA628
G
Ives Architectural hardware products
E9
Wall Stops
•
•
•
WS33
Meets ANSI/BHMA 156.16, L12011
WS33X
Meets ANSI/BHMA 156.16, L12021
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
WS33
WS33X Wall Stops
Constructed in a durable cast brass.
Replaceable rubber bumper with offset shoulder screws into cavity on body
to prevent loss or theft.
Sloping design discourages vandalism
WS33 is furnished with wood screws for drywall mounting.
WS33X is furnished with a threaded stud and expansion shield for
masonry type mounting.
Dimensions
Base Diameter: 2-1/4” wide x 3” High
Overall Projection: 3-3/4”
Finishes brass
US Number US26D
D
Latches, Catches & Bolts
C
BHMA626
WS65 Wall Stop
E10
• Burnished cast aluminum.
• Replaceable non-marring white rubber bumper.
• Packed with sheet metal screws.
Stops
Dimensions
Base Diameter: 1-5/8”
Overall Projection: 3-3/4”
Exterior Hardware
Finishes aluminum
Ives Number US3
G
Miscellaneous Hardware
F
BHMA
E10
Ives Architectural hardware products
US10
US10B
US27
666668 703 673
Wall Bumpers
Hinges & Pivots
WS401CCV & WS402CCV
Meets ANSI/BHMA 156.16 L12251 for brass
WS401CVX (401) – convex rubber bumper, packed with wood screw
and plastic anchor.
WS401CCV (401-1/2) – concave rubber bumper which avoids damage to locks
with projecting buttons, packed with wood screw and plastic anchor.
WS402CVX (402) – convex rubber bumper packed with screw and drywall anchor.
WS402CCV (402-1/2) – concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor.
Dimensions
C
Base Diameter: 2-1/2”
Flush Bolts & Coordinators
• Constructed in heavy-duty cast brass.
• Special retainer cup makes rubber tamper resistant.
B
Pulls & Plates
WS401CVX & WS402CVX
Meets ANSI/BHMA 156.16 L12101 for brass
A
WS401CVX Wall Bumpers
WS401CCV
WS402CVX
WS402CCV
Base Thickness: 3/8”
Overall Projection: 1”
US3
BHMA
605606 612 613 619 625 626
US4
US10
US10B
US15
US26 US26D
D
Latches, Catches & Bolts
Finishes
Ives Number
WS404CVX Wall Bumpers
• Compact size.
• Constructed in cast brass.
• Totally concealed mounting discourages vandalism or tampering.
• Unit furnished with grey convex rubber bumper.
• Packed with sheet metal screw, rawl plug and brad.
Stops
E11
Dimensions
Base Diameter: 1”
US3
BHMA
605606609 612 613 619 625 626
US4
US5
US10
US10B
US15
US26 US26D
F
Finishes
Ives Number
Exterior Hardware
Overall Projection: 17/32”
G
Miscellaneous Hardware
Ives Architectural hardware products
E11
Hinges & Pivots
Wall Bumpers
WS406CVX & WS407CVX
Meets ANSI/BHMA 156.16 L22201 for brass,
and L52101 for stainless steel.
WS406CCV & WS407CCV
Meets ANSI/BHMA 156.16 L22251 for brass
and and L52251 for stainless steel.
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
WS406CVX Wall Bumpers
WS406CCV
WS407CVX
WS407CCV
•
•
•
•
Constructed in sturdy yet economical wrought base of brass
or stainless steel construction.
Feature concealed tamper-proof mounting.
Shipped factory preassembled backplate to reduce installation cost.
Easy installation by inserting screwdriver through small hole in rubber.
WS406CVX (406) – convex rubber bumper, packed with wood screw
and plastic anchor.
WS406CCV (406-1/2) – concave rubber bumper, which avoids damage to locks with projecting buttons, packed with wood screw and plastic anchor.
WS407CVX (407) – convex rubber bumper packed with screw and drywall anchor.
WS407CCV (407-1/2) – concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor.
Dimensions
Base Diameter: 2-1/2”
Base Thickness: 3/8”
Overall Projection: 1”
Finishes brass
Ives Number US3
BHMA
US4
US5*
US10
Stops
E12
BHMA630
* only available on WS407CVX Slim-Pak of 15
G
Miscellaneous Hardware
F
Exterior Hardware
** available on WS407CCV or WS407CVX Slim-Pak of 15
Ives Architectural hardware products
US15 US15A** US26 US26D
605 606609*612 613 619 620 625 626
Finishes stainless steel
Ives Number US32D
E12
US10B
B716**
Wall Bumpers
A
•
•
•
Hinges & Pivots
411R-W Wall Bumper
Adhesive-backed wall door stop for use on clean, smooth, flat surfaces only.
Non-marring white rubber.
Concave design permits knob to strike stop without damaging or
engaging lock mechanism.
Pulls & Plates
Dimensions
Base Diameter: 1-7/8”
B
Base Thickness: 3/8”
Overall Projection: 1-1/16”
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
Stops
E13
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
E13
Wall Stops & Holders
• Constructed in brass.
• Ideal for interior or exterior use.
• Replaceable non-marring rubber tip.
WS443 is packed with expansion shield and lead shield for masonry type mounting.
WS447 is packed with wood screws for drywall mounting.
Dimensions
WS443
Meets ANSI/BHMA 156.16, L12021 for brass
and L32021 for aluminum.
Base Diameter: 2-1/4”
Overall Projection: 3-11/16”
Finishes brass
Ives Number US3
BHMA
US4
US10
US10B
US15
US26 US26D
605606 612 613 619 625 626
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
WS443
WS447 Wall Stop
Stops
E14
D
WS445
WS449 Manual Wall Holder
•
•
•
•
WS445
Meets ANSI/BHMA 156.16, L11351 for brass.
WS449
Meets ANSI/BHMA 156.16, L11341 for brass
and L31341 for aluminum.
Dimensions
Constructed in cast of brass or aluminum.
Unit functions as a stop but serves as a Hold-Open device when hook
is manually engaged in strike.
Unit requires manual disengagement to release Hold-Open.
Replaceable resilient, non-marring rubber tip.
WS445 is packed with expansion shield and lead shield for masonry type mounting.
WS449 is packed with wood screws for drywall mounting.
Base Diameter: 2-1/4”
Base Projection: 3-11/16”
Engaged Projection: 5-3/4”
Exterior Hardware
Strike Height: 1-1/2”
Strike Width: 13/16”
F
Strike Projection: 13/16”
Finishes brass
Ives Number US3
Miscellaneous Hardware
BHMA
BHMA628
* only available on WS449
Ives Architectural hardware products
US10
US10B
US15
US26 US26D
605606 612 613 619 625 626
Finishes aluminum
Ives Number US28*
G
E14
US4
Automatic Wall Holders
Constructed of sturdy cast brass, or aluminum.
Holder is mounted on wall and strike is mounted on door.
Roller on holder rides up seats itself on strike, with a heavy duty bumper
pad deadening the sound and shock.
Universal screw pack accommodates all types wall construction.
A
•
•
•
•
Hinges & Pivots
WS40 Automatic Wall Holder
Dimensions
Base Height: 2”
Base Width: 2-1/2”
Base Projection: 2-1/4”
Engaged Projection: 3-1/2”
US10
US10B
US26 US26D
605606 612 613 625626
C
Finishes aluminum
Ives Number US28
BHMA628
US10B
US26 US26D
605606 612 613 625626
G
Finishes aluminum
Ives Number US28
Miscellaneous Hardware
US10
F
BHMA
US4
Exterior Hardware
Finishes brass
Ives Number US3
Strike Diameter: 2-3/8
Strike Projection: 3”
Stops
Base Height: 3-11/16” Base Width: 3”
Base Projection: 2”
Engaged Projection: 3-7/16”
E15
Dimensions
D
• Constructed of cast brass, bronze or aluminum.
• Spring loaded roller rides up the face of the strike,
seating itself on the strike, holding the door firmly in the open position.
• A heavy rubber pad cushions the shock and absorbs the sound.
• With unit mounted on door and the strike on wall, vertical adjustment
is available on body.
• The strike is adjustable 45 degrees left or right, both adjustments easily
accomplished at time of installation or at a later date.
WS45 strike is furnished with wood screws for drywall mounting.
WS45X strike is furnished with a threaded stud and expansion shield
for masonry type mounting.
Latches, Catches & Bolts
WS45
WS45X Automatic Wall Holder
WS45
Meets ANSI/BHMA 156.16, L11291 for brass
and L31291 for aluminum.
Flush Bolts & Coordinators
BHMA
US4
B
Finishes brass
Ives Number US3
Strike Height: 2-1/16”
Strike Width: 3/4”
Strike Projection: 2”
Pulls & Plates
Meets ANSI/BHMA 156.16, L11291 for brass
and L31291 for aluminum.
BHMA628
Ives Architectural hardware products
E15
Hinges & Pivots
Kick Down Holders
FS452 Kick Down Holder
•
•
•
•
•
•
Pulls & Plates
A
B
Units provide simple hold and release, activated with a touch of the foot.
Cast brass or aluminum construction.
Stainless steel spring.
Replaceable non-marring rubber shoes have corrugated bottoms to provide
secure grip.
Shoes are easily replaced when worn. Shoe held on with screw.
Packed with sheet metal screws.
FS452-4 has a door-to-floor clearance of 2” or less.
FS452-5 has a door-to-floor clearance up to 3”.
Meets ANSI/BHMA 156.16, L11383 for brass
and L31383 for aluminum.
C
Flush Bolts & Coordinators
Dimensions
FS452-4 Door-to-Floor Clearance: 2” or less
FS452-5 Door-to-Floor Clearance: Up to 3”
FS452-4 Plate Height: 2-1/8”
FS452-5 Plate Height: 2-1/8”
FS452-4 Plate Width: 1”
FS452-5 Plate Width: 1”
Finishes brass
Ives Number US3
BHMA
US4
US10
US10B
US15
US26 US26D
605606 612 613 619 625 626
Latches, Catches & Bolts
Finishes aluminum
Ives Number US28*
D
BHMA628
* available in 4” only
FS455 Kick Down Holder
Stops
E16
•
•
•
•
Units provide simple hold and release, activated with a touch of the foot.
Cast brass or aluminum construction.
Replaceable non-marring rubber shoes have corrugated bottoms to provide
secure grip. When worn, shoes are easily replaced. Shoe held on with screws.
Door-to-floor clearances of 2” or less.
Dimensions
Plate Height: 1-3/4”
Plate Width: 1-3/4”
F
Exterior Hardware
Door-to-Floor Clearance: 2” or less
Meets ANSI/BHMA 156.16, L11382 for brass
and L31382 for aluminum.
Finishes brass
Ives Number US3
Miscellaneous Hardware
BHMA
US5
US10
BHMA
Ives Architectural hardware products
US10B
US15
US26 US26D
605606609 612 613 619 625 626
Finishes aluminum
Ives Number US3AL US5AL US10AL US27
G
E16
US4
666609668673
Kick Down Holders
FS544 for door-to-floor clearances of 2” or less
FS555 for door-to-floor clearances up to 3”.
B
Dimensions
FS544
Meets ANSI/BHMA 156.16, L11381
FS544
Door-to-Floor Clearance: 2” or less
Plate Height: 2-1/4”
Plate Width: 1-7/16”
FS555
Door-to-Floor Clearance: Up to 3”
Plate Height: 2-1/4”
Plate Width: 1-7/16”
SP4
BHMA
706 691 689695 622
SP10
SP28
SP313 SPBLK
C
Finishes
Ives Number
Flush Bolts & Coordinators
FS555
Meets ANSI/BHMA 156.16, L11391
Pulls & Plates
A
• Units provide an economical method to hold open doors.
• Cast of durable iron.
• Non-marring rubber shoes have corrugated bottoms to provide secure grip.
Rubber shoe is securely fastened with screw. When worn, shoes are easily
replaced.
Hinges & Pivots
FS544
FS555 Kick Down Holder
D
Latches, Catches & Bolts
Stops
E17
F
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
E17
Plunger Type
Door Holders
Hinges & Pivots
FS1153 Plunger Type Door Holder
Provides a contemporary yet economical method of positive Hold-Open.
Constructed in sturdy cast aluminum.
Spring operated plunger activates with minimal pressure, releasing instantly with a light tap on the plat-form lever.
Provides a 1-5/8” throw for all types of doors.
Ribbed non-marring rubber shoe is securely fastened to unit with a screw
and is easily replaced when worn.
Dimensions
Meets ANSI/BHMA 156.16, L31401.
Height: 6-1/4”
Width: 1-1/2”
Depth: 1-7/16”
Finishes
Ives Number
Flush Bolts & Coordinators
B
Pulls & Plates
A
•
•
•
•
•
US28
C
BHMA628
Latches, Catches & Bolts
FS1154 Plunger Type Door Holder
D
•
•
•
•
Constructed from heavy-duty cast brass or bronze.
Plunger and internal parts are plated steel and provides a 1-1/4” throw for
all types of doors.
Plunger is easily activated with minimal pressure, releasing instantly with a light tap on the platform lever.
Round non-marring rubber shoe is securely fastened with a screw in flanged cup to prevent movement or loss. When worn, shoes are easily replaced.
Dimensions
G
Miscellaneous Hardware
F
Exterior Hardware
Stops
E18
Meets ANSI/BHMA 156.16, L11401.
E18
Ives Architectural hardware products
Height: 5-1/2”
Width: 2”
Depth: 1-1/4”
Finishes
Ives Number
US3
BHMA
605606 612 613 625626
US4
US10
US10B
US26 US26D
Roller Bumpers
FS470
Meets ANSI/BHMA 156.16, L12212
Constructed in heavy-duty cast brass.
RB470 used where two doors open against each other to
prevent damage to the doors or hardware.
RB471 and RB472 are ideal for use in situations where doors
meet each other at approximate right angles (back to back).
Replaceable rubber roller available.
B
Dimensions
RB470 Base Size: 1-11/16” x 2-1/4”
RB470 Arm Offset: 2-3/4”
RB470 Length: 5”
Flush Bolts & Coordinators
A
A
C
RB471 Base Diameter: 2”
RB471 Length: 4-1/2”
RB472 Base Diameter: 2”
RB472 Length: 6”
FS471
B
US3
BHMA
605606**612* 613* 619* 625 626
US4** US10* US10B* US15*
US26 US26D
* only available on RB472
** only available on RB471 and RB472
A
D
B
Finishes
Ives Number
Latches, Catches & Bolts
Meets ANSI/BHMA 156.16, L12192
Pulls & Plates
B
Offset
A
•
•
•
•
Hinges & Pivots
RB470
RB471
RB472 Roller Bumpers
A
A
A
A
Stops
E19
FS472
Meets ANSI/BHMA 156.16, L12202
F
Exterior Hardware
Miscellaneous Hardware
A
A
G
Ives Architectural hardware products
E19
A
Hinges & Pivots
Residential Door Stops
Meets ANSI/BHMA A156.16
060 061
Flexible Door Stops
• Utilizes heavy gauge spring to maintain rigid protections
• Simple to install - only a screwdriver required
• Made from burnished wrought steel
• Packed disassembled for quick installation
Replaceable white rubber tip available
Pulls & Plates
Dimensions
B
Base Diameter: 1”
Tip Diameter: 19/16”
060 3” Projection
061 4” Projection
Flush Bolts & Coordinators
BHMA
Latches, Catches & Bolts
Finishes steel
Ives Finish
F3
60 61
F5
F10
F10B
F14
F15*
F26D
F-W**
632638 639640645646652
* only available on 060
C
** only available on 061
Base Door Stops
D
• Available in three sizes to accommodate varying areas of installation
and door trim dimensions
• Made from solid brass or aluminum
• 61 also available in epoxy colored aluminum
Replaceable white/black rubber tip available
Dimensions
Stops
E20
60 3-3/4” Projection, Base Diameter: 1”
61 3-1/8” Projection on brass units, 3-3/16” Projection on aluminum units,
Base Diameter: 7/8”, Tip Diameter: 5/8”
Finishes brass
Ives Finish
B3
Finishes aluminum
Ives Finish
A3
BHMA
E20
B5
B10
B10B
B15
B15A*
B26
B26D B716**
605606609 612 613 619 620 625 626
A5*
A10*
A10B
A14
A15*
A19*
A92
A716*
A-BLK
666 668703 669670 A19 673
Finishes zinc
Ives Finish
Z605* Z619*
Z716*
BHMA
* only available on 61
** only available on 61 Schlage Carded or slim package of 15
Note: 61A - 716 ships with black rubber tips
G
Miscellaneous Hardware
F
Exterior Hardware
BHMA
B4
Ives Architectural hardware products
A-W*
Residential Door Stops
• Utilizes heavy gauge spring to maintain rigid protections
• Simple to install - only a screwdriver required
• Made from burnished wrought steel
• Packed disassembled for quick installation
Replaceable white rubber tip available
A
Flexible Door Stops
Hinges & Pivots
63 Dimensions
B
Pulls & Plates
Base Diameter: 1”
Tip Diameter: 9/16”
Projection: 3”
Finishes steel
Ives Finish
F605E F609E F619E
F-W
632638646
C
Base Door Stop
• Base Door Stop features deluxe one-piece styling
• Easily screws into base
• Designed with square head to accommodate wrench or pliers when installing
• Made from solid brass or aluminum
Replaceable white rubber tip available
Dimensions
D
Base Diameter: 1”
Tip Diameter: 9/16”
Projection: 3-1/4”
Finishes brass
Ives Finish
B3
B4
B5
B10
B10B
B15
B26
B26D
605606609 612 613 619 625 626
Stops
BHMA
A10B
E21
Finishes aluminum
Ives Finish
A3
A92
666703 673
BHMA
F5
F10
F10B
G
70° to 100° Door Opening Adjustments
Miscellaneous Hardware
Door Opening
F
Hinge Pin Door Stops
• For use on hinged doors where the installation of a standard door
stop is not desirable
• Positive slip proof adjustment
• Non-marring rubber tips
• Removable bushings accommodate 1/4” to 5/16” diameter hinge pins
• Easy installation—only a screwdriver required
• Made from burnished wrought steel
Replaceable white rubber tip available
Exterior Hardware
69
Finishes steel
Ives Finish
F3
Latches, Catches & Bolts
64 BHMA
Flush Bolts & Coordinators
BHMA
F716
F14
F15
F15A
F26
F26D
632638 639640645646 647 651 652
Ives Architectural hardware products
E21
Residential Door Stops
Hinges & Pivots
70
B
Pulls & Plates
A
• For use on hinged doors where the installation of a standard door stop
is not desirable
• Designed for narrow trim installation
• High quality rubber bumpers - shoulder on stud supports rubber through
entire body for engineered cushioning
• Removable bushings accommodate 1/4” to 5/16” diameter hinge pins
• Easy installation
• Made from solid brass, aluminum, or epoxy coated aluminum
Replaceable white/black rubber tip available
70-Zinc
Door Opening
Finishes brass
Ives Finish
B3
C
Flush Bolts & Coordinators
BHMA
85° to 125° Door Opening Adjustments
B4
B5
B10
B10B
B15
B15A* B19
B26
B26D
B716*
605606609 612 613 619 620 622 625 626
Finishes aluminum
Ives Finish
A3
A4
BHMA
667
666
A5
A10
A10B
A14
A15
A92
668
716
669
670
673
Finishes zinc
Ives Finish
Z605E Z406E**Z619E** Z716E
72
E22
A-W
A-BLK
** only available in Schlage Carded
Note: 70A - 716 ships with black rubber tips
Door Saver
A716
* only available in Schlage Carded or Slim-Pak of 25
BHMA
D
Latches, Catches & Bolts
Hinge Pin Door Stops
Hinge Pin Door Stops
•
•
•
•
•
•
For use on hinged doors where the installation of a standard door stop
is not desirable
Designed for narrow trim installation
High quality rubber bumpers - shoulder on stud supports rubber through
entire body for engineered cushioning
Removable bushings accommodate 1/4” to 5/16” diameter hinge pins
Easy installation
Made from solid brass, aluminum, or epoxy coated aluminum
Door Opening
Stops
85° to 125° Door Opening Adjustments
Finishes zinc
Ives Finish
Z605E Z609E Z613E Z619E Z625E
Z-W
BHMA
G
Miscellaneous Hardware
F
Exterior Hardware
73
E22
Door Saver
Meets ANSI/BHMA 156.6, L12141 for brass
or bronze and L32141 for aluminum.
Hinge Pin Door Stops
•
•
•
•
•
•
For use on hinged doors where the installation of a standard door stop
is not desirable
Designed for narrow trim installation
High quality rubber bumpers - shoulder on stud supports rubber through
entire body for engineered cushioning
Removable bushings accommodate 1/4” to 5/16” diameter hinge pins
Easy installation
Made from solid brass, aluminum, or epoxy coated aluminum
Door Opening
85° to 125° Door Opening Adjustments
Finishes zinc
Ives Finish
Z605E Z613E
BHMA
Ives Architectural hardware products
Z619E Z625E
Door Silencers
Door Silencer
Packed in bags of 100.
Grey Available in bulk pack of 2500.
Each bag has an installation tool included.
Pulls & Plates
Meets ANSI/BHMA 156.16, L03011.
For use on metal frames featuring pneumatic design that, once installed,
forms an air pocket to absorb shock and reduce noise of door closing.
Tamper-proof once installed on the frame.
Proper installation also eliminates door rattle and provides constant
tension for door latches or locks.
A
•
•
•
Hinges & Pivots
SR64
Dimensions
B
Diameter: 1/2”
Thickness: 1/8”
Finishes
Door Silencer
•
•
Dimensions
Height: 3/4”
D
Meets ANSI/BHMA 156.16, L03021
Packed in bags of 100.
Latches, Catches & Bolts
For use on wood frames, also feature pneumatic design to cushion shock
and absorb noise.
To prevent removal, a small brad should be driven into stop strip
and through stem of silencer, as shown in the detail.
C
SR65
Flush Bolts & Coordinators
GRY, TAN
Diameter: 3/8”
Thickness: 1/8”
Finishes
GRY
Stops
E23
SR66 Door Silencer
• Self Adhesive Rubber Silencers.
• Economical installation requires no drilling of frames.
Packed two sheets of 50 (100 minimum).
Exterior Hardware
Dimensions
F
Diameter: 1/2”
Thickness: 1/8”
Finishes
BRN, GRY, WHT
G
Miscellaneous Hardware
Ives Architectural hardware products
E23
G
Miscellaneous Hardware
F
Exterior Hardware
Stops
E24
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
A
Hinges & Pivots
Notes
E24
Ives Architectural hardware products
Exterior Hardware
A
Hinges & Pivots
Table Of Contents
Lock Guards
B
Flush Bolts & Coordinators
F5
F5
F6
F6
C
Viewers
U696 One-way Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
698, U698 One-way Viewer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
700, U700 One-way Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
701, U701 One-way Viewer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pulls & Plates
page
LG1, LG7 Lock Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2
LG10 Lock Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F2
LG11 Lock Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3
LG12 Lock Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F3
LG13 Lock Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
LG14 Lock Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4
Door Knockers
3107 Door Knocker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7
3125 Door Knocker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7
D
Latches, Catches & Bolts
Letter Box
620 Letter Box Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
601 Letter Box Sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F8
Door Numbers
02-30 Door Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
Storm and Screen Door
980 Storm Door Latch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F9
25 Screen Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
E
Stops
Crash Stop
CS115 Crash Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F10
F1
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
F1
Hinges & Pivots
Lock Guards
A
LG1
LG7
B
Pulls & Plates
Lock Guard
•
•
•
•
•
•
Units are non-handed and incorporate security frame pin to
prevent separation of the door and frame. LG7 does not incorporate the
security frame pin
Unit covers the latch bolt area of the door and lock, thereby providing
added protection from burglars, vandals or normal abuse.
Ideal for use with mortise or cylindrical locks.
Easy installation.
Through bolted with carriage bolts and nuts.
Available in a variety of materials, 13 gauge stainless steel,
12 gauge steel and brass material.
C
Flush Bolts & Coordinators
Dimensions
3" Wide x 11-1/2" High
Bolt center to center: 10-1/2"
Finishes
Ives Number
USP* US2G*
BHMA
600603 606 612 630695
US4*
US10* US32D SP313*
D
Latches, Catches & Bolts
* not available on LP7
LG10
E
Stops
•
•
•
•
•
Ideally suited for use with rose or escutcheon 2-3/4" wide or less.
For use with Type 86 Mortise and Type 161 Cylindrical Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
No exposed fasteners on face of unit.
Unique design provides maximum security, virtually eliminating the
opening between door and frame at the latch point.
Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
F2
Exterior Hardware
Dimensions
2-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2"
G
Miscellaneous Hardware
F2
Lock Guard
Ives Architectural hardware products
Finishes
Ives Number
USP
BHMA
600630
US32D
Lock Guards
Lock Guard
B
Dimensions
2-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2"
Flush Bolts & Coordinators
Finishes
Ives Number US32D SP313
BHMA
Pulls & Plates
Designed for use on aluminum doors with latch-type locks
or doors equipped with electric strikes.
Unit is Handed - Specify left or right hand when ordering.
No exposed fasteners on face of unit.
Unique design provides maximum security, virtually eliminating the
opening between door and frame at latch point.
Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
A
•
•
•
•
•
Hinges & Pivots
LG11
630695
C
D
Latches, Catches & Bolts
LG12
Lock Guard
E
Narrow design unit for use on rose or escutcheon 3-1/2" or less.
For use with Type 86 Mortise and Type 161 Cylinder Locks
(ANSI 156.13 Series 1000 and ANSI 156.2 Series 4000).
No exposed fasteners on face of unit.
Unique design provides maximum security, virtually eliminating the opening between door and frame at the latch point.
Available in 13 Gauge Stainless Steel or 12 Gauge Steel
Stops
•
•
•
•
•
Dimensions
1-1/2" Wide x 9-1/2" High
Stud center to center: 8-1/2”
USP
BHMA
600630
Exterior Hardware
Finishes
Ives Number
F3
US32D
G
Miscellaneous Hardware
Ives Architectural hardware products
F3
Hinges & Pivots
Lock Guards
LG13
Lock Guard
A
•
•
•
•
Designed for use on all Type 161 Cylindrical Locks (ANSI 156.2 Series 2000)
Monolock and Unilock.
No exposed fasteners on face of unit.
Unique design provides maximum security, virtually eliminating the
opening between door and frame at latch point.
Available in 13 Gauge Stainless Steel or 12 Gauge Steel.
Finishes
Ives Number
USP
BHMA
600630
US32D
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
Dimensions
1-1/2" Wide x 7" High
Stud center to center: 4-1/2"
LG14
Lock Guard
•
•
•
•
•
Narrow design unit for use on rose or escutcheon 3-1/2" or less.
For use with Von Duprin 6210 and 6211 electric strike.
No exposed fasteners on face of unit.
Unique design provides maximum security.
Available in 13 Gauge Stainless Steel
E
Stops
Dimensions
2-9/16" Wide x 9-1/2" High
Stud center to center: 8-1/2"
Finishes
Ives Number US32D
G
Miscellaneous Hardware
F4
Exterior Hardware
BHMA630
F4
Ives Architectural hardware products
Viewers
•
•
•
•
•
•
•
150° Angle of View.
For doors 1-3/8" to 2-1/16" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation — only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
B4
BHMA
606613 626
B
Finishes
Ives Number
Pulls & Plates
Meets ANSI/BHMA A156.16 L23222
UL Listed 90 minute fire doors
A
Hinges & Pivots
U696 One-Way Viewer
B10B
B26D
C
Flush Bolts & Coordinators
•
•
•
•
•
•
•
190° Angle of View.
Lens projects 1/4" from face of door.
4 optical glass lenses.
For doors 1-3/8" to 2-1/8" thick.
Solid brass body and barrel.
Simple installation — only a 9/16" hole required.
Suggested installation height: 60" from floor.
B3
BHMA
605619 626
E
Finishes
Ives Number
Stops
698 meets ANSI/BHMA A156.16 L23172
U698 meets ANSI/BHMA A156.16 L23222
U698 is UL Listed 90 minute fire doors
D
Latches, Catches & Bolts
698
U698 One-Way Wide Angle Viewer
B15**
B26D
B716*
* not available on U698
** only available in Schlage Carded
F5
Exterior Hardware
G
Miscellaneous Hardware
Ives Architectural hardware products
F5
Hinges & Pivots
Viewers
700 meets ANSI/BHMA A156.16 L23173
U700 meets ANSI/BHMA A156.16 L23222
U700 is UL Listed 90 minute fire doors
•
•
•
•
•
•
•
120° Angle of View.
For doors 1-3/8" to 2-1/16" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation—only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
Finishes
Ives Number
B3**
BHMA
605606 613 626
B4
B10B*
B26D
* not available on U700
Flush Bolts & Coordinators
B
Pulls & Plates
A
700
U700 One-Way Viewer
701 meets ANSI/BHMA A156.16 L23173
U701 meets ANSI/BHMA A156.16 L23222
U701 is UL Listed 90 minute fire doors.
G
Miscellaneous Hardware
F6
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
C
** only available on 700 in Schlage Carded
F6
Ives Architectural hardware products
701
U701
One-Way Viewer
•
•
•
•
•
•
•
120° Angle of View.
For doors 2-1/8" to 2-5/8" thick.
Secure, tamper-resistant.
Solid brass body; glass lens.
Simple installation—only a 1/2" hole required.
Suggested installation height: 60" from floor.
Trim washer available, 3/4" x .032" thick.
Finishes
Ives Number
B4
BHMA
606613 626
B10B
B26D
Door Knockers
• Knocker made from forged brass.
• Only available in Schlage Carded pak
A
Hinges & Pivots
02-3107 Knocker Only
B
Pulls & Plates
Dimensions
Length: 8-1/2"
Width: 4-1/8"
Projection: 1"
Mounting Hole Center-to-Center: 5"
Meets ANSI/BHMA A156.16 L23151
Finishes
Ives Number
B605
BHMA
605619
B19
C
• Knocker made from forged brass.
• 02-31251 and 02-31251U for door thickness 7/8" – 1-9/16"
• 02-31252 and 02-31252U for door thickness 1-5/8" – 2-1/8"
D
Dimensions
Length: 5-15/16"
Width: 3"
Projection: 1-1/16"
Mounting Hole Center-to-Center: 3-15/16"
BHMA
605609 619 620 625626
B15
B15A*
B26
B26D
716
E
B3
Stops
Finishes
Ives Number
B5
Latches, Catches & Bolts
Flush Bolts & Coordinators
02-3125 Knocker Only
02-31251U Knocker with U700 Viewer
02-31252U Knocker with U701 Viewer
* not available on viewer, only available in Schlage Carded
Meets ANSI/BHMA A156.16 L23161
F7
Exterior Hardware
Only B3, B15, B26D and 716 knockers are available with viewer. B3 is furnished with B4
(606) viewer, 716 is furnished with B10B viewer, B15 (619) is furnished with a 636 viewer.
G
Miscellaneous Hardware
Ives Architectural hardware products
F7
B
Pulls & Plates
A
Hinges & Pivots
Door Knockers
620 Magazine Size Letter Box Plate with
Standard (Open) Back Plate
• Spring-loaded front plate
• Sex Bolt mounting available, order separately 09-355 – finish.
Dimensions
Overall Size: 13" Wide x 3-9/16" High
Plate Opening: 11" x 2" High
Meets ANSI/BHMA A156.16 L26031
Finishes brass
Ives Number
B3
Flush Bolts & Coordinators
BHMA
B15
B15A*
B26
C
BHMA628
F8
Exterior Hardware
E
Stops
D
Latches, Catches & Bolts
* not available in U700 Schlage Carded
G
Ives Architectural hardware products
B26D
605609 619 620 625626
Finishes aluminum
Ives Number PA28
Miscellaneous Hardware
F8
B5
601 Sleeve for use with Letter Box Plate
• Made of stainless steel.
• For 1-3/4" hollow core doors.
B716
House Numbers
Hinges & Pivots
A
SC2 - 30 X 6 Heritage House Number
• Made from solid brass.
Schlage Carded
B
Pulls & Plates
5 - 3056
6 - 3066
7 - 3076
8 - 3086
9 - 3096
0 - 3006
1 - 3016
2 - 3026
3 - 3036
4 - 3046
Dimensions
Height: 4"
605619
Storm Door Latch
•
•
•
•
•
For wood storm doors 7/8" to 1-1/8" thick.
Reversible: fits right or left hand, inswinging or outswinging doors.
Security lock feature operates from inside rose.
Solid brass safety strike assures latching and is designed to
compensate for air pressure build-up between doors.
Made from wrought brass.
B10B
B15
B19
B26
B26D
605609 613 619 622 625 626
F9
B5
Exterior Hardware
BHMA
E
Finishes brass
Ives Number
B3
Stops
Dimensions
Backset: 1-3/4"
Rose Diameter: 1-7/8"
Knob Diameter: 1-3/4"
Knob Projection: 2"
Lever Length: 1-3/4"
Lever Projection: 1-7/8"
D
Latches, Catches & Bolts
980 B716
C
BHMA
B15
Flush Bolts & Coordinators
Finishes brass
Ives Number
B3
G
Miscellaneous Hardware
Ives Architectural hardware products
F9
A
Hinges & Pivots
Crash Stops
25
Screen Door Pull
• Cast aluminum or epoxy-coated aluminum
• Also used as a window lift, drawer or utility pull
Dimensions
Meets ANSI/BHMA A156.16, L12231,
Projection 1-5/32"
Mounting holes 4-1/8" center to center
Finishes
Ives Number
A3
BHMA
666673
A92
A-W
A-B
CS115 Crash Stop
•
•
•
•
•
•
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
B
Pulls & Plates
Length 4-7/8"
Meets ANSI/BHMA A156.16, L12231,
Specially designed for full-size exterior doors.
Tear resistant, grey vinyl cover.
Heavy duty compression spring assembled to both ends of chain
and end brackets.
Packed with sheet metal screws.
Cast Brass brackets with solid, welded steel chain.
Optional sex bolt mounting available in US26D (626) only.
Dimensions
Bracket Size: 1-9/16" x 1-9/16"
Available Lengths:
E
Stops
20-1/2" — Recommended for 30" Door Width (Product No. CS115-20)
25-1/2" — Recommended for 36" Door Width (Product No. CS115-25)
30-1/2" — Recommended for 42" Door Width (Product No. CS115-30)
F10
Exterior Hardware
Finishes
Ives Number US10B US26D
G
Miscellaneous Hardware
BHMA
F10
Ives Architectural hardware products
613626
Miscellaneous Door Hardware
C
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G1
Miscellaneous Hardware
Ives Architectural hardware products
Flush Bolts & Coordinators
Cabinet/Closet Hardware
2 Elbow Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
22 Flush Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
218 Finger Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G13
221 Flush Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
222 Flush Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
223 Flush Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G14
227 Flush Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
230 Slide Door Edge Pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
42 Pocket Sliding Door Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G15
990 Sliding Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G16
991 Sliding Door Pull. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G16
B
Hobby Hardware
78 Hook and Staple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
86 Hobbyist Barrel Bolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9011, 9031 Middle Butt Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9041 Middle Butt Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9042 Broad Butt Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G9
9070 Decorative Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9071, 9072 Decorative Hinge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9110 Decorative Hasp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9120 Hasp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G10
9130 Hook with Hasp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9210 Support Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9220 Friction Lid Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9311, 9212 Decorative Corner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G11
9320 Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9321 Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9330 Draw Catch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
9340 Chest Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
Pulls & Plates
Window Hardware
07 Window Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
90 Side Window Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
026 Bar Window Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
066 Casement Fastener. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G7
66 Casement Fastener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G8
71 Casement Adjuster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G8
A
Hooks & Brackets
059 Handrail Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
59 Handrail Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
159 Handrail Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G2
405 Coat & Hat Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
571 Coat & Hat Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
572 Coat & Hat Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G3
574 Coat & Hat Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
575 Coat & Hat Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
580 Ceiling Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G4
581 Wardrobe Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G5
582 Wardrobe Hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G5
585 Closet Pole Socket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
586 Closet Pole Socket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G6
Hinges & Pivots
Table Of Contents
page
G1
A
Hinges & Pivots
Hand Rail Brackets and Hooks
059
Hand Rail Bracket
• Made from solid brass, cast aluminum or epoxy-coated aluminum.
• Large faceplate for secure attachment to wall.
• Features solid construction for increased strength.
Dimensions
Meets ANSI/BHMA A156.16 L13061
for brass and L33061 for aluminum
Flush Bolts & Coordinators
B
Pulls & Plates
Base: 2-1/4" High x 1-3/8" Wide
Base to Center of Rail: 2-7/16"
B5
B10B
B15
B15A
B19
B26
B26D
605
609
613
619
620
622
625
626
Finishes aluminum
Ives Number A3
A5
A10
A10B
A14
A15
A92
A716 A-BLK A-W
668
703
669
670
673
BHMA
BHMA
666
59
Hand Rail Bracket
• Made from cast brass or cast aluminum.
• Large faceplate for secure attachment to wall.
• Features solid construction for increased strength.
C
Dimensions
Meets ANSI/BHMA A156.16 L13061
for brass and L33061 for aluminum
Aluminum Base: 2-13/16" High x 1-1/2" Wide
Brass Base: 2-15/16" High x 1-1/2" Wide
Base to Center of Rail: 2-3/4"
Stops
Finishes brass
Ives Number
B3
E
BHMA
G2
Miscellaneous Hardware
F
Exterior Hardware
BHMA
B5
A5
Hand Rail Bracket
•
•
•
•
Finishes aluminum
Ives Number
A3
BHMA
B26D
B716
A14
A15
A92
A716
For use on commercial applications.
Exceeds OSHA and BHMA strength test requirements.
Packed with square head iron lag screw, expansion shield and screws.
Cast Aluminum construction.
Base Diameter: 3-1/8"
Base to Rail Center: 3-1/8"
Ives Architectural hardware products
A10B
159
B26
666 703669670673
Dimensions
Meets ANSI/BHMA A156.16, L33081
B15
605609 619 625 626
Finishes aluminum
Ives Number
A3
G2
B716
Finishes zinc
Ives Number Z619E
D
Latches, Catches & Bolts
Finishes brass
Ives Number B3
A92
666673
Hooks
• Wide body design is ideal for public buildings, schools, dormitories,
etc., where hook must withstand unusual stress and strain.
• Made from cast aluminum.
A
Coat & Hat Hook
Hinges & Pivots
405
Dimensions
Finishes aluminum
Ives Number
A3
A4
A5
A10
A10B
A14
A92
BHMA
667
668
703
669
673
666
• All-purpose hook in traditional design.
• Made from cast brass, cast aluminum, or epoxy-coated aluminum.
Dimensions
Base: 1-3/4" High x 1-1/4" Wide
Projection: 3"
Meets ANSI/BHMA A156.16 L13113
for brass and L33113 for aluminum.
B5
B10B
B15
B15A*
B26
B26D
B716
605606609 613 619 620 625 626
Finishes aluminum
Ives Number
A3
BHMA
A5
A10
A14
A15
A92
A716 668
669
670
673
666
A-W
A-BLK
E
BHMA
Stops
Finishes zinc
Ives Number Z619E
D
BHMA
B4
Latches, Catches & Bolts
Finishes brass
Ives Number
B3
C
Coat & Hat Hook
Flush Bolts & Coordinators
571
B
Meets ANSI/BHMA A156.16 L33113
Pulls & Plates
Base: 1-1/2" High x 7/8" Wide
Projection: 2-1/2"
* only available in Schlage Carded or Slim-Pak of 25
Coat & Hat Hook
• Step-up decorative version of the traditional all-purpose hook.
• Ideal for locations where additional strength is required.
• Made from cast brass or cast aluminum.
F
Dimensions
Brass Base: 1-1/2" High x 1-5/16" Wide
Aluminum Base: 1-5/8" High x 1-5/16" Wide
Projection: 3"
B5
B10
B10B
B15
B26
B26D
BHMA
605
606
609
612
613
619
625
626
Finishes aluminum
Ives Number A3
A5
A10
A10B
A14
A15
A92
668
703
669
670
673
666
Ives Architectural hardware products
G3
B4
Miscellaneous Hardware
Finishes brass
Ives Number B3
BHMA
Exterior Hardware
572
G3
574
Coat & Hat Hook
• Decorative design is ideal for commercial and residential installations.
• Made from cast brass, cast aluminum or epoxy-coated aluminum.
Dimensions
Base: 1-5/8" High x 1-3/4" Wide
Projection: 3-3/4"
Overall Height, Brass: 4-3/4"
Overall Height, Aluminum: 5"
Finishes brass
Ives Number B3
B
Pulls & Plates
A
Hinges & Pivots
Hooks
BHMA
B10
B10B
B15
B26
B26D
605606 612 613 619 625 626
Finishes aluminum
Ives Number A3
A26
A92
BHMA
672
673
666
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Meets ANSI/BHMA A156.16 L13113 for
brass and L33113 for aluminum
B4
575
Coat & Hat Hook
• Especially designed to accommodate large hats.
• Made from solid brass or cast aluminum.
D
Dimensions
Base: 2-1/4" High x 1-3/8" Wide
Projection: 3-5/8"
Overall Height: 5-3/4"
A10B
A92
BHMA
703
673
666
E
Stops
Meets ANSI/BHMA A156.16 L33121
Finishes aluminum
Ives Number A3
580
Exterior Hardware
F
Dimensions
Base: 1" High x 1-7/8" Wide
Projection: 2-1/4"
G4
Miscellaneous Hardware
G4
Ceiling Hook
• Ideal for use in closets, attached to underside of shelves,
or in storage lockers.
• Made from cast brass or cast aluminum.
Ives Architectural hardware products
Finishes
Ives Number
A3
A5
A10
A14
A15
A92
BHMA
666
668
669
670
673
A716
Hooks
A
Wardrobe Hook
• Compact hook is perfect where space is limited,
such as behind doors where low profile is needed.
• Made from cast brass, cast aluminum or epoxy-coated aluminum.
Hinges & Pivots
581
Dimensions
B4
B5
BHMA
666
B10B
B15
B15A*
B26
B26D
612
613
619
620
625
626
A716
A-BLK
A-W
A5
A14
A15
A92
669
670
673
B716
C
Finishes aluminum
Ives Number A3
B10
Flush Bolts & Coordinators
BHMA
605
606
609
* only available in Schlage Carded
B
Finishes brass
Ives Number B3
Pulls & Plates
Base, Brass/Aluminum: 1-1/4" High x 1-1/4" Wide
Base, Zinc: 1-1/2" High x 3/4" Wide
Projection, Brass: 1-11/16"
Projection, Aluminum, Zinc: 1-5/8"
BHMA
D
Latches, Catches & Bolts
Finishes zinc (narrow base)
Ives Number Z619E
582
Double Wardrobe Hook
• Compact double hook is perfect where space is limited,
such as behind doors where low profile is needed.
• Made from cast brass, cast aluminum or epoxy-coated aluminum.
Dimensions
B10
B10B
B15
B15A*
B26
B26D
B716
605606609 612 613 619 620 625 626
F
Finishes aluminum
Ives Number
A3
BHMA
B5
Exterior Hardware
BHMA
B4
E
Finishes brass
Ives Number
B3
Stops
Base, Brass: 1-1/8" High x 1-1/4" Wide
Base, Aluminum: 1-1/16" High x 1-3/16 Wide
Base, Zinc: 1-5/8" High x 7/8" Wide
Projection, Brass: 1"
Projection, Aluminum, Zinc: 1-3/32"
A5
A10
A14
A15
A92
A716
A-W
A-BLK
666 668669 670 673
Miscellaneous Hardware
Finishes zinc (narrow base)
Ives Number Z619E
G5
BHMA
* only available in Schlage Carded or Slim-Pak of 25
Ives Architectural hardware products
G5
A
Hinges & Pivots
Window Hardware
SP585 Closet Pole Sockets
•
•
•
•
B
Pulls & Plates
Finishes
Ives Number
Flange design prevents accidental knock out of pole.
Made from wrought steel.
Accommodates pole or pipe with outside diameter of 1-3/8".
Packed in pairs.
F3
C
Flush Bolts & Coordinators
BHMA632
SP586 Closet Pole Sockets
Latches, Catches & Bolts
•
•
•
•
Made from a heavy duty plastic for long life and extra strength.
Single screw mounting.
Accommodates pole or pipe with outside diameter of 1-3/8".
Packed in pairs.
Finish
D
White Plastic
07
E
Stops
•
•
•
•
F
Exterior Hardware
G6
Miscellaneous Hardware
Base: 15/16" x 2-9/16"
Strike: 5/8" x 2-9/16"
Finishes brass
Ives Number
B3
BHMA
B15
B15A*
B26
B26D
B716
605619 620625 626
Finishes aluminum
Ives Number
A3
BHMA
Designed low to the sash for superior strength and greater
resistance to breakage.
Vertical and horizontal camming action for snug, non-rattling fit.
Heavy gauge springs provide long-wearing action.
Made from solid brass, aluminum, or epoxy coated aluminum.
Dimensions
Meets ANSI/BHMA A156.16
G6
Window Lock
A5*
A10B
A14
A15
A92
A-716
A-W
666 703669670673
* only available in Schlage Carded or Slim-Pak of 25
Ives Architectural hardware products
A-BLK
Window Hardare
• May be used singularly for small windows or in pairs for large windows.
• Cam action eliminates rattles and holds window firmly in desired position.
• Made from aluminum.
Dimensions
A
Side Window Lock
Hinges & Pivots
90
1-3/4" High x 1-1/8" Wide
A3
B
Meets ANSI/BHMA A156.16
Pulls & Plates
Finishes
Ives Number
BHMA666
• Facilitates opening of window in a safe manner.
• Can also be used as a drawer or utility pull.
• Made from solid brass, aluminum, or epoxy coated aluminum.
Dimensions
BHMA
B5
B15
B15A*
B26
B26D
B716
D
Finishes brass
Ives Number
B3
Latches, Catches & Bolts
Base: 1-1/8" High x 4" Wide
Projection: 1-1/16"
605609 619 620 625626
Finishes aluminum
Ives Number
A3
BHMA
A5
A14
A15
A92
A716
A-W
C
Bar Window Lift
Flush Bolts & Coordinators
Meets ANSI/BHMA A156.16
026
A-BLK
666 669670 673
E
Stops
* only available in Schlage Carded or Slim-Pak of 25
066
Casement Fastener
Dimensions
Base: 1-5/8" x 7/8"
Projection: 1-3/8"
B26
B26D
605609 619 625 626
Finishes aluminum
Ives Number
A3
BHMA
B15
A5
A10B
A14
G7
BHMA
B5
Miscellaneous Hardware
Finishes brass
Ives Number
B3
F
Meets ANSI/BHMA A156.16
For use on windows to provide weather-tight fastening and security.
Also ideal for securing louvered doors and small doors.
Made from solid brass or aluminum.
Specify: Surface , Rim , or Mortise
Strike (SS)
Strike (RS) Strike (MS)
Exterior Hardware
•
•
•
•
A92
666668 703 673
Ives Architectural hardware products
G7
66
Meets ANSI/BHMA A156.16
For use on windows to provide weather-tight fastening and security.
Also ideal for securing louvered doors and small doors.
Made from solid brass or aluminum.
Specify: Surface , Rim
Mortise
Strike (SS)
Strike (RS)
Strike (MS)
Dimensions
Base: 2-1/16" High x 1-1/16" Wide
Projection: 1-7/8"
Finishes brass
Ives Number
B3
BHMA
Finishes aluminum
Ives Number
A3
BHMA
B5
B15
B26
B26D B716
605609 619 625 626
A5
A14
A92
666 669673
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Casement Fastener
•
•
•
•
B
Pulls & Plates
A
Hinges & Pivots
Window Hardware
71
Meets ANSI/BHMA A156.16
Casement Adjuster
•
•
•
•
Securely holds casement window in any position.
Can also be used to hold cabinet lids and drafting table tops in
various positions.
Made from burnished steel or solid brass.
Available in 10" and 12" lengths.
E
Stops
Dimensions
Tube: 3/8" x 5/8"
Projection: 1"
Sash Plate:
Brass: 1-5/8" High x 5/8" Wide
Steel: 2 x 5/8" Wide
Sill Plate:
Exterior Hardware
2-1/4" x 15/16" Wide
F
Finishes brass
Ives Number
B3
G8
Miscellaneous Hardware
BHMA
G8
Ives Architectural hardware products
B26
605625
Hobby Hardware
Hook and Staple
• Made from solid brass.
Hinges & Pivots
78
A
Dimensions
Hook: 1-1/2” Long
Staple: 3/4” high x 15/16” wide
Finishes
Ives Number
B3
BHMA605
• Made from solid brass.
B
Hobbyist Barrel Bolt
Pulls & Plates
86
Dimensions
B3
C
Finishes
Ives Number
Flush Bolts & Coordinators
Bolt plate: 1-9/16” high x 1-11/16” wide
Bolt guide: 1-9/16” high x 7/16” wide
Strike plate: 1-9/16” high x 5/8” wide
BHMA603
Middle Butt Hinge
Middle Butt Hinge
• Made from solid brass.
Latches, Catches & Bolts
9011
9031
D
Dimensions
9011 Overall height x overall width: 3/4” x 11/16”
9031 Overall height x overall width: 1-1/2” x 1”
Finishes
Ives Number
B3
BHMA605
Middle Butt Hinge
• Made from solid brass.
E
9041
Stops
Schlage Carded - 9011 4 per, 5 cards per box. 9031 2 per, 5 cards per box.
Dimensions
Overall height x overall width: 2” x 1-1/4”
Exterior Hardware
Finishes
Ives Number
B3
F
BHMA605
Schlage Carded - 2 per, 5 cards per box.
Broad Butt Hinge
• Made from solid brass.
Miscellaneous Hardware
9042
Dimensions
Finishes
Ives Number
B3
BHMA
605609
G9
Overall height x overall width: 2” x 1-3/8”
B5
Schlage Carded - 2 per, 5 cards per box.
Ives Architectural hardware products
G9
A
Hinges & Pivots
Hobby Hardware
9070
Decorative Hinge
• Made from steel.
Dimensions
Overall height x overall width: 1-5/16” x 2-7/8”
Pulls & Plates
Finishes
Ives Number
F3
B
BHMA632
C
Flush Bolts & Coordinators
Schlage Carded - 2 per, 5 cards per box.
9071
9072
Decorative Hinge
Decorative Hinge
• Made from solid brass.
Dimensions
Latches, Catches & Bolts
9071 Overall height x overall width: 1-3/4” x 3”
9072 Overall height x overall width: 1-5/16” x 2-1/4”
Finishes
Ives Number
B3
BHMA
605609
B5
D
Schlage Carded - 1 per card, 5 cards per box.
9110
Decorative Hasp
• Made from solid brass.
Dimensions
E
Stops
Overall height x overall width: 5/8” x 1-7/8”
Finishes
Ives Number
B3
BHMA
605609
B5
F
Exterior Hardware
Schlage Carded - 2 per, 5 cards per box.
9120
Hasp
• Made from solid brass.
Dimensions
G10
Miscellaneous Hardware
Overall height x overall width: 3/4” x 2-3/4”
G10
Finishes
Ives Number
B3
BHMA
605609
B5
Schlage Carded - 1 per card, 5 cards per box.
Ives Architectural hardware products
Hobby Hardware
• Made from solid brass.
A
Hook with Hasp
Hinges & Pivots
9130
Dimensions
Overall height x overall width: 3/4” x 2-3/4”
Pulls & Plates
B3
B
Finishes
Ives Number
BHMA605
Schlage Carded - 1 per, 5 cards per box.
• Made from steel.
• Handed. Specify Left Hand (LH) or Right Hand (RH)
Dimensions
Extension: approx. 10-3/8”
F3
Latches, Catches & Bolts
Finishes
Ives Number
C
Support Hinge
Flush Bolts & Coordinators
9210
BHMA632
D
Schlage Carded - 1 per, 5 cards per box.
9220
Friction Lid Support
• Made from steel.
• Handed. Specify Left Hand (LH) or Right Hand (RH)
Dimensions
E
Finishes
Ives Number
Stops
Extension: approx. 5”
F3
BHMA632
Decorative Corner
• Made from solid brass.
F
9311
Exterior Hardware
Schlage Carded - 1 per, 5 cards per box.
Dimensions
B3
G11
Finishes
Ives Number
Miscellaneous Hardware
9311 Side to corner: 1-3/4”
BHMA605
Schlage Carded - 4 per card, 5 cards per box.
Ives Architectural hardware products
G11
A
Hinges & Pivots
Hobby Hardware
9320
Bracket
• Made from solid brass.
Dimensions
Each leaf 1/2” x 1-1/8”
Pulls & Plates
Finishes
Ives Number
B3
BHMA605
Flush Bolts & Coordinators
B
Schlage Carded - 4 per, 5 cards per box.
9321
Bracket
• Made from solid brass.
Dimensions
C
Each leaf 1/2” x 1-9/16”
Finishes
Ives Number
B3
Latches, Catches & Bolts
BHMA605
D
Schlage Carded - 4 per, 5 cards per box.
9330
Draw Catch
• Made from steel.
Dimensions
Overall height: 1-1/2”
Overall width: 2-3/4”
E
Stops
Finishes
Ives Number
F3
BHMA632
F
Exterior Hardware
Schlage Carded - 2 per, 5 cards per box.
Chest Handle
• Made from steel.
Dimensions
Overall height: 1-1/2”
Overall width: 3-1/2”
Finishes
Ives Number
Miscellaneous Hardware
F3
BHMA632
G12
G12
9340
Schlage Carded - 2 per, 5 cards per box.
Ives Architectural hardware products
Cabinet/Closet Knobs and Pulls
• Ideal for use on the inactive leaf of a pair of cabinet doors.
• Surface applied, making installation simple.
• Made from cast aluminum.
A
Elbow Catch
B
Finishes aluminum
Ives Number A3
BHMA
A5
666
A14
A15
A92
669
670
673
A716
C
Flush Pull
Low profile makes this pull ideal for louvered, bi-folding or
wardrobe doors.
Extra deep recess and reverse tapered grip provide for ease of pulling
and gripping.
Made from wrought brass.
D
Dimensions
1-5/16" High x 3-1/8" Wide x 7/16" Deep
Meets ANSI/BHMA A156.9 B22201
and A156.14 D2781.
Finishes brass
Ives Number B3
BHMA
605
Latches, Catches & Bolts
•
•
•
Flush Bolts & Coordinators
22
Pulls & Plates
Dimensions
Plate: 1-3/8" High x 5/8" Wide
Strike: 13/16" High x 5/8" Wide
Meets ANSI/BHMA A156.9 B33023
Hinges & Pivots
2
B5
B10B
B15
B26
B26D
609
613
619
625
626
E
Stops
Finger Pull
• Ideal for use on sliding doors.
• Easy installation.
• Made from wrought brass.
F
Exterior Hardware
218
BHMA
605
B5
B10
B10B
B15
B26
B26D
609
612
613
619
625
626
Ives Architectural hardware products
G13
Finishes brass
Ives Number B3
Miscellaneous Hardware
Meets ANSI/BHMA A156.9 B22201
and A156.14 D2781.
Dimensions
Inside Cup Diameter: 3/4"
Overall Diameter: 1"
Depth: 5/16"
G13
Cabinet/Closet Knobs and Pulls
Hinges & Pivots
221
B
Pulls & Plates
A
•
•
•
•
Ideal for use on sliding doors.
Built-in prong design eliminates the need for screws or brads and
facilitates installation.
Packed with two escutcheon pins for added holding power.
Made from wrought brass.
Dimensions
Inside Cup Diameter: 2-1/8"
Overall Diameter: 2-7/16"
Depth: 7/16"
Meets ANSI/BHMA A156.9 B22201
and A156.14 D2781
Finishes brass
Ives Number B3
B4
B5
B10
B10B
B15
B15A*
B26
B26D
BHMA
606
609
612
613
619
620
625
626
605
B716
* only available in Slim-Pak of 25
222
Flush Pull
•
•
•
Low profile makes this pull ideal for louvered, bi-folding or
wardrobe doors.
Reverse tapered grip provide for ease of pulling. Made from cast brass.
D
Latches, Catches & Bolts
C
Flush Bolts & Coordinators
Flush Pull
Dimensions
3-1/8" High x 1-5/8" Wide x 7/16" Deep
E
Stops
Meets ANSI/BHMA A156.9 B12201
and A156.14 D1781.
Finishes brass
Ives Number B3
B4
B5
B10
B10B
B15
B26
B26D
BHMA
606
609
612
613
619
625
626
223
Flush Pull
• Low profile makes this pull ideal for louvered, bi-folding
or wardrobe doors.
Exterior Hardware
F
G14
Miscellaneous Hardware
G14
605
• Made from wrought brass
Dimensions
3-9/16" High x 1-5/16" Wide x 1/2" Deep
Meets ANSI/BHMA A156.9 B22201
and A156.14 D2781.
Ives Architectural hardware products
Finishes brass
Ives Number B3
B4
B10
B10B
B15
B26
B26D
BHMA
606
612
613
619
625
626
605
Cabinet/Closet Knobs and Pulls
Flush Pull
•
•
•
•
Contoured for ease of pulling.
Extra deep well.
Deluxe quality. Made from wrought brass.
A
Hinges & Pivots
227
B
Pulls & Plates
Dimensions
3-5/8" High x 1-3/4" Wide x 9/16" Deep
Meets ANSI/BHMA A156.9 B22201
and A156.14 D2781.
Finishes
Ives Number
B3
B4
B5
B10
B10B
B15
B26
B26D
BHMA
605
606
609
612
613
619
625
626
C
Flush Bolts & Coordinators
230
Sliding Door Edge Pull
• 3/4" width allows installation on narrow as well as standard doors.
• Spring automatically returns lever flush with plate.
• Made from solid brass.
D
Latches, Catches & Bolts
Dimensions
3-7/8" High x 3/4" Wide
Finishes
Ives Number
B3
B4
B5
B10
B10B
B15
B26
B26D
BHMA
605
606
609
612
613
619
625
626
Meets ANSI/BHMA A156.14 D2801.
E
Stops
42
Pocket Sliding Door Bolt
Exclusive Ives design permits emergency release of bolt from
outside the door.
Spring activated design allows feather-touch action.
Brass grommet supplied to cap release hole, protecting the
door’s finish.
Made from wrought brass.
F
Exterior Hardware
•
•
•
•
B3
B4
B5
B10
B10B
B15
B26
B26D
BHMA
605
606
609
612
613
619
625
626
Ives Architectural hardware products
G15
Finishes
Ives Number
Miscellaneous Hardware
Dimensions
Overall Size Plate: 3-1/16" High x 1-5/32" Wide
Strike: 1" High x 3/4" Wide
Depth of Mortise: 5/8"
G15
A
Hinges & Pivots
Cabinet/Closet Knobs and Pulls
990
Sliding Door Pull
•
•
•
•
Fits doors 1-3/8" to 1-1/2".
Decorative coined edges.
Pre-assembled for doors opening left to right. Plates are reversible.
Body and strike made from solid brass.
B
Pulls & Plates
Dimensions
1-3/4" D x 2-1/4" H
Finishes brass
Ives Number B3
B5*
B10B
B15
B15A*
B26
BHMA
609
613
619
620
625
A14
A15
A26D
A716
669
670
702
605
B716
* only available in Schlage Carded
Flush Bolts & Coordinators
Finishes aluminum
Ives Number A3
D
Latches, Catches & Bolts
C
BHMA
666
991
Sliding Door Pull
•
•
•
•
Fits doors 1-3/8" to 1-1/2".
Decorative coined edges.
Pre-assembled for doors opening left to right. Plates are reversible.
Body, turn knob and strike made from solid brass.
E
Stops
Dimensions
1-3/4" D x 2-1/4" H
Finishes brass
Ives Number B3
B5*
B10B
B15
B15*
B26
BHMA
609
613
619
620
625
A14
A15
A26D
A716
669
670
702
605
* only available in Schlage Carded
Finishes aluminum
Ives Number A3
G16
Miscellaneous Hardware
F
Exterior Hardware
BHMA
G16
A5
Ives Architectural hardware products
A5
666
B716
A
Hinges & Pivots
B
Pulls & Plates
C
Flush Bolts & Coordinators
D
Latches, Catches & Bolts
E
Stops
F
Exterior Hardware
G17
Miscellaneous Hardware
G17
Ives Architectural hardware products
About Allegion
Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security.
As a $2 billion provider of security solutions for homes and businesses, Allegion
employs more than 7,800 people and sells products in more than 120 countries
across the world. Allegion comprises 23 global brands, including strategic
brands CISA®, Interflex®, LCN®, Schlage® and Von Duprin®.
For more, visit www.allegion.com
© 2014 Allegion
005313, Rev. 02/14
www.allegion.com/us
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising