HCD95534/X True Day/Night IR Camera User

HCD95534/X True Day/Night IR Camera User
HCD95534
True Day/Night
IR Camera
NTSC
PAL
HCD95534
HCD95534X
User Guide
Document 800-01802 – Rev B – 02/09
Revisions
Issue
Date
Revisions
A
11/08
New document
B
02/09
Corrected illumination length to 125-150
ft (40 - 46 m).
2
Warnings
Installation and servicing should be performed only by qualified and
experienced personnel to conform to all local codes and to maintain your
warranty.
WARNING!
12 VDC/24 VAC models require the use of CSA
Certified/UL Listed Class 2 power adapters to ensure
compliance with electrical safety standards.
Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to
operate the equipment.
Caution
To prevent electric shock and risk of fire hazards do not
use power sources other than that specified.
Explanation of Graphical Symbols
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
Document 800-01802 Rev B
02/09
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
3
FCC Compliance Statement
Information to the User: This equipment has been tested and found to
comply with the limits for a Class A digital device. Pursuant to Part 15 of the
FCC Rules, these limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Caution
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC directive
2004/108/EC and the Low Voltage Directive LVD 2006/95/EC, conforming to
the requirements of standards EN 55022 for emissions, EN50130-4 for
immunity, and EN 60950 for Electrical Equipment safety.
4
Important Safety Information
•
•
•
•
•
•
•
•
Read and keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
Precautions
•
•
•
•
•
•
•
Please ensure that your installation area can support the weight of the
camera.
Do not install the camera in extreme temperature conditions. Only use
the camera where temperatures are between -13°F and 122°F (-25°C
and 50°C). Be especially careful to provide ventilation when operating
under high temperatures.
Do not aim the camera towards an extreme light source to prevent
damaging the CCD.
Do not touch the camera bezel (front glass plate).
Do not drop the camera or subject it to physical shock.
Do not expose the camera to radioactivity.
Do not use a strong or abrasive detergent when cleaning the camera.
Caution
Note
The light emitted from the near-infrared light emitting
diodes (LEDs) provides illumination over a wide area.
This light is not considered a risk to the unshielded
human eye. However, as with any light source, it is
recommended that normal precautions be taken to
avoid unnecessary exposure. For example, avoid
staring into the beam or viewing directly with optical
instruments at close range.
IR LEDs could be warm after prolonged use.
Document 800-01802 Rev B
02/09
5
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Positioning the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lens Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the Zoom and Focus of the Lens . . . . . . . . . . . . . . . . . . 9
Camera Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SETUP Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPECIAL Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SPECIAL Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . 14
Adding a Camera Title Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Configuring Sync Control/Line-lock . . . . . . . . . . . . . . . . . . . . . . . 16
Setting Up Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuring Privacy Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Warranty and Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6
Introduction
The Honeywell HCD95534 Color IR camera is designed for exceptional value
and performance and is ideally suited for use in day-to-day surveillance
applications. The off-the-shelf feature set is designed for high picture quality
in standard applications and the HCD95534 requires little to no adjustment
after installation.
Figure 1
Camera Overview
Sunshield
Photo cell
IR LED
Lens adjustment
Camera settings
(behind access cover)
5–50 mm IR
corrected
vari-focal lens
Mounting bracket
Features
•
•
•
•
•
•
•
•
High resolution 530 TVL 1/3” CCD provides a high-quality picture in lowlight conditions
26 IR LEDs for illumination up to 125~150 ft. (40~47 m) depending on
scene reflectivity, DSS on
5 – 50 mm F1.6 IR corrected Vari-focal lens with external controls for
zoom and focus
External access for camera On-screen Display (OSD) menu and day
night threshold controls
Digital Noise Reduction (DNR) minimizes video noise in low light
Digital Slow Shutter (DSS) for improved light sensitivity to extend the
range of the light that the camera can detect in low-light conditions
Automatic day/night switching with adjustable threshold level control
12 VDC or 24 VAC operation
Document 800-01802 Rev B
02/09
7
Before You Begin
Unpack Everything
Check that the items received match those listed on the order form and
packing slip. The HCD95534 packing box should include, in addition to this
User Guide:
• One HCD95534 camera
• Four mounting screws
• One video test cable
• One allen wrench
• One adapter plate for 4S mounting box
If any parts are missing or damaged, contact the dealer you purchased the
camera from or call Honeywell Customer Service (see the back of this
manual).
Note
A Phillips screwdriver and a flathead screwdriver may assist your
installation.
Installation
The HCD95534 camera is designed for installation on a wall or ceiling. The
HCD95534 is weather sealed for indoor or outdoor locations.
Attaching the Camera
1.
2.
3.
Position the camera to the desired mounting location on a wall or ceiling.
Be sure the location is solid on a flat, smooth surface (for example, a
crossbeam).
Using the supplied mounting template, mark the four screw holes for
installation.
Using four screws appropriate to your installation, mount the camera at
the marked holes.
The mounting bracket can be separated from the camera housing for
easier installation. This is done by unscrewing and removing the thumb
screw on the bracket. Replace and tighten the thumb screw after
installation is complete.
8
Note
To ensure a waterproof installation, the notch in the camera base
that the power and video connections exit through should be facing
down.
If the power and video connections exit the top of the base (wall
mounted only), water may pool in the camera base. To minimize
moisture entering the base, apply appropriate sealant around the
notches and any other gaps between the camera base and the
mounting surface.
Positioning the Camera
Caution
Do not swivel and position the camera without the
mounting bracket firmly in place.
Loosen the thumb screws and move the camera into position. Swivel the
camera to capture the desired field of view. Tighten the thumb screws to set
the position.
Lens Setup
Adjusting the Zoom and Focus of the Lens
The zoom and focus adjustment is located on the underside front end of the
camera housing. Use a flathead screwdriver to adjust the zoom and/or focus.
Figure 2
Lens Controller
Zoom adjustment screw
Turn counter-clockwise for wide angle
Turn clockwise for telephoto
Focus adjustment screw
Turn counter-clockwise for near focus
Turn clockwise for far focus
Document 800-01802 Rev B
02/09
9
Camera Settings
Camera Functions
Figure 3
Camera Controller
ON
VIDEO-TEST
1
1 STEP
LUX LEVEL
2 STEP
UP
LEFT
4
RIGHT
3 STEP
DOWN
SETUP (MENU)
PUSH DOWN
3
4 STEP
LED-LEVEL
2
Legend
# Description
1 Video-test monitor output connector
2 LUX-level adjustment DIP switches. Only one switch should be on at a
time. They modify the point at which the lux threshold (level of light)
changes the mode of operation (color or B/W).
STEP
Color to B/W (LED on) B/W to Color (LED off)
1
11–12 lux
12–13 lux
2
8–9 lux
10–11 lux
3
6–7 lux
7–8 lux
4
1–3 lux
3–5 lux
3 LED-level adjustment screw. Increase (turn clockwise) or
lower (turn counter-clockwise) the IR LED brightness in night (B/W)
mode.
4 Camera OSD control (four position plus center push)
10
Legend
# Description
Press this control
To do this …
UP, DOWN
Select a new item
LEFT, RIGHT
Select a menu item
SETUP (MENU)
Access a submenu
Connecting the Camera
1.
2.
Connect the BNC video output connector to the video-in connector on
your monitor or video recorder.
Connect the camera to a power supply appropriate for your installation
(12 VDC or 24 VAC).
Figure 4
Camera Connection
Document 800-01802 Rev B
02/09
11
Programming
Setup Menu
The HCD95534 menu system consists of one main Setup menu (see
Figure 5) for easy camera programming.
Press down on the SETUP (MENU) control (see Figure 3) to display the
Setup menu.
Figure 5
1
2
3
4
5
6
7
8
9
Setup Menu
<<SETUP MENU>>
LENS
DC!
SHUTTER
–––
WHITE BAL.
ATW
BACKLIGHT
OFF
AGC
MIDDLE!
DNR
MIDDLE
DSS
OFF
SPECIAL!
EXIT MENU
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
AGC
DNR
DSS
SPECIAL!
EXIT MENU
DC! , VIDEO, MANUAL
FLK, ESC! , MANUAL
ATW, MANUAL! , AWC!
OFF, LOW, MIDDLE, HIGH
OFF, LOW! , MIDDLE! ,
HIGH!
OFF, LOW, MIDDLE, HIGH
OFF, AUTO!
! indicates submenus
SETUP Menu Functions
Menu Item
1 LENS
12
Option
Description
DC!
VIDEO
MANUAL
Selects Lens type (the HCD95534 only
supports DC mode at this time; choosing any
other mode may cause incorrect/
unpredictable camera operation).
Menu Item
2 SHUTTER
Option
Description
FLK
ESC!
MANUAL
Adjusts shutter settings.
FLK = Flickerless mode reduces on-screen
flickering. This is the only option available
when the camera lens is set to DC mode
(recommended).
ESC = Electronic Shutter Control adjusts
brightness level on screen.
MANUAL = Allows you to adjust the shutter
speed from 1/60-1/120,000 of a second
(NTSC), or 1/50-1/120,000 (PAL).
3 WHITE BAL. ATW
MANUAL!
(White
AWC!
Balance)
Controls color on the screen.
4 BACKLIGHT OFF
LOW
MIDDLE
HIGH
Provides light level control to overcome
severe
backlighting conditions.
5 AGC
(Automatic
Gain
Control)
Adjusts value of AGC gain.
OFF
LOW!
MIDDLE!
HIGH!
ATW = Select Auto Tracing White Balance
when the color temp is 2400°K-12000°K (for
example, under fluorescent light, or
outdoors).
MANUAL = Allows you to increase or
decrease the red or blue factor on screen.
AWC = Auto White Balance Control
automatically adjusts the white balance to
your specific environment.
Increase the GAIN level to brighten the
picture.
Caution Noise or distortion may develop.
6 DNR
(Digital
Noise
Reduction)
OFF
LOW
MIDDLE
HIGH
Document 800-01802 Rev B
02/09
Reduces noise/distortion on the screen.
Increasing the DNR level reduces noise but
may introduce video artifacts. DNR is
deactivated if AGC is turned off.
13
Menu Item
7 DSS
(Digital Slow
Shutter)
Option
Description
OFF
AUTO!
Automatically provides a clear image under
low-light conditions. You can control the
maximum low-light magnification from 2x to
128x (increasing magnification may cause
noise/distortion). DSS is deactivated when
SHUTTER is set to FLK mode.
8 SPECIAL!
Opens the SPECIAL menu (see next section).
9 EXIT
Exits the SETUP menu and returns to video
monitoring.
SPECIAL Menu
1.
On the Setup menu, press the menu control UP or DOWN and then
select SPECIAL.
Press the SETUP (MENU) control to access the Special menu.
2.
Figure 6
1
2
3
4
5
6
7
8
9
SPECIAL Menu
<<SPECIAL MENU>>
CAMERA ID
OFF
COLOR
AUTO
SYNC
INT
MOTION DET
OFF
PRIVACY
OFF
MIRROR
OFF
SHARPNESS
ON!
RESET
RETURN!
! indicates submenus
14
CAMERA ID
COLOR
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
RETURN!
OFF, ON!
AUTO, ON
INT (L/L)
OFF, ON!
OFF,ON!
OFF, ON
ON! , OFF
SPECIAL Menu Functions
Menu Item Option
Description
1 CAMERA
ID
OFF
ON!
Sets a name to be displayed on the monitor.
See Adding a Camera Title Display.
2 COLOR
AUTO
ON
Sets the camera to either automatic color/
black and white or full-time color mode.
3 SYNC
INT
Synchronizes the vertical interval sync pulse
of your camera with other equipment to
reduce the effect of picture roll on the monitor.
L/L!
In Line Lock (L/L) mode you can adjust the
phase from 0~359°.
4 MOTION
DET
OFF
ON!
Detects moving objects on screen, and
displays MOTION DETECTED along with the
number of movements counted.
Allows you to select the area on screen you
want to observe. See Setting Up Motion
Detection.
5 PRIVACY
OFF
ON!
Allows you to mask certain areas of the screen
from observation.
6 MIRROR
OFF
ON
Produces a horizontal mirror image on
screen.
7 SHARPNESS
ON!
OFF
Sharpens the image on screen. You can
adjust the sharpness level from 0~31.
Caution Excessive sharpening may cause
picture noise.
8 RESET
Restores all factory default settings.
9 RETURN!
Returns to the main Setup menu.
Document 800-01802 Rev B
02/09
15
Adding a Camera Title Display
To add a camera title:
1. On the Special menu, select CAMERA ID and then press SETUP
(MENU).
Figure 7
Adding Camera Title
<<CAMERA ID>>
ABCDEFGHIJKLM
NOPRQSTUVWXYZ
a b c d e f g h i j k l m
n o p q r s t u v w x y z
– . 0 1 2 3 4 5 6 7 8 9
" # CLR POS END
_______________
2.
3.
4.
5.
16
Press the menu control UP, DOWN, LEFT, or RIGHT to select a
character, then press SETUP (MENU) to accept it. The character is
saved and the title cursor at the bottom of the screen moves to the next
position. You can use the " # symbols to go back or forward in the title
name to make changes, and you can also select CLR to delete the entire
title and start again.
Repeat step 2 until your camera title is complete.
Select POS to position where you would like the camera title to be
located on screen. Select the position using the menu control, then
press (SETUP) MENU to confirm the position.
Select END when you are finished.
Configuring Sync Control/Line-lock
Use this screen to synchronize the vertical interval sync pulse of your camera
with other equipment to reduce the effect of picture roll on the monitor.
Note
Line-lock mode is only available when using 24 VAC power.
Figure 8
Sync Control Setup
<<SYNC. CONTROL>>
SYNC
INT (L/L)
RETURN!
Menu Item Description
INTERNAL When line-lock is not required.
LINELOCK Adjusts the vertical phase (VPH):
RETURN
VPH: 000~359 (factory default is 0)
Press MENU to return to the Setup menu.
Document 800-01802 Rev B
02/09
17
Setting Up Motion Detection
Use this screen to set up to four areas of the screen to detect moving
objects. The screen displays MOTION DETECTED along with the number of
movements counted.
Figure 9
Motion Detection Setup
<<MOTION DETECTION>>
AREA SEL
AREA STATE
TOP
DOWN
LEFT
RIGHT
AREA 1
ON
|..|................| 10
|........|..........| 25
|...|...............| 20
|........|..........| 40
Press SET to Return
Menu
Option
Item
AREA SEL AREA 1
AREA 2
AREA 3
AREA 4
AREA
ON
STATE
OFF
TOP
DOWN
LEFT
RIGHT
18
Description
Selects which of the four motion detection grids top
left, top right, bottom left, bottom right) you would
like to modify.
Activates or deactivates the selected grid.
Press LEFT or RIGHT menu control to alter the
dimensions of the selected grid.
Configuring Privacy Zones
Use this screen to set up to four areas of the screen for privacy mode; that is,
the camera does not record video in these areas.
Figure 10 Privacy Mode Setup
<<PRIVACY>>
AREA SEL
AREA 1
AREA STATE
ON
AREA TONE
|...............|...| 80
TOP
|..|................| 10
DOWN
|........|..........| 25
LEFT
|...|...............| 20
RIGHT
|........|..........| 40
Press SET to Return
Menu Item
AREA SEL AREA 1
AREA 2
AREA 3
AREA 4
AREA
ON
STATE
OFF
AREA
TONE
TOP
DOWN
LEFT
RIGHT
Document 800-01802 Rev B
02/09
Description
Selects which of the four masking grids (top left,
top right, bottom left, bottom right) you would
like to modify.
Activates or deactivates the selected grid.
Changes the shade of the masking grids, by
pressing the LEFT or RIGHT menu control.
Alters the dimensions of the selected grid by
pressing the LEFT or RIGHT menu control.
19
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during
the warranty period Honeywell will repair or replace, at its sole option, free of
charge, any defective product returned prepaid.
In the event you have a problem with any Honeywell product, please call
Customer Service at 1.800.796.CCTV (North America only) for assistance or
to request a Return Merchandise Authorization (RMA) number. For
Europe and the United Kingdom, please contact your Honeywell dealer.
Be sure to have the model number, serial number, and the nature of the
problem available for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits.
Items shipped to Honeywell without a clearly identified Return
Merchandise Authorization (RMA) number may be refused.
Specifications
HCD95534 (NTSC)
HCD95534X (PAL)
Operational
Image Sensor:
Video Standard:
Scanning System:
Number of Pixels
(H x V):
Minimum Illumination:
PAL
525/60 lines
625/50 lines
768 x 494
752 x 582
0 lux, operates in complete darkness
Horizontal
Resolution:
Video Output:
Greater than 530 TVL
Sync System:
12 VDC: Internal
S/N Ratio:
Auto Gain Control:
ALC:
Automatic Electronic
Shutter:
20
1/3” CCD
NTSC
1 Vp-p @ 75 Ohms
24 VAC: Internal/Line lock
50 dB or more (AGC off)
Off/On, selectable
Adjustable level control
1/60–
1/120,000 sec
1/50–
1/120,000 sec
HCD95534 (NTSC)
Lens Type:
HCD95534X (PAL)
5-50 mm Vari-focal Auto Iris, IR corrected, F1.6
Horizontal Field of
View:
White Balance:
ATW/AWC/Manual
BLC:
Off/On, selectable
Gamma:
Line Lock Phase
Adjustment:
IR LEDs:
IR Illumination
Distance:
Digital Noise
Reduction:
Digital Slow Shutter:
Electrical
Input Voltage:
Input Range:
51.3°–5.5°
0.45
Adjustable Line lock vertical phase
850 nm, 26 LEDs
125 ft (40 m)–150 ft (47 m), depending on scene
reflectivity, DSS on
Off/Low/Middle/High
x2–x128
12 VDC/24 VAC
11–16 VDC, 17–28 VAC
Surge Suppression:
1.5 kW transient
Power Consumption:
15 W (max) with IR LEDs on
Mechanical
Dimensions:
Weight:
Construction:
Connector:
See diagram below
2.8 lb (1.27 kg)
Housing: brushed and anodized aluminum with sunhood
Finish: brushed and anodized aluminum
Main Video Output: BNC connector
Aux Video Output: 2-pin connector for video test cable
Power Input: Tinned leads
Environmental
Temperature:
Relative Humidity:
Operating: -13°F to 122°F (-25°C to 50°C)
Storage: -35°F to140°F (-35°C to 60°C)
0% to 85%, non-condensing
Rating:
IP66
Regulatory
Emissions:
FCC, CE (EN 55022)
Immunity:
Safety:
Document 800-01802 Rev B
02/09
CE (EN 50130-4)
EU: 2006/95/EC LVD
21
Dimensions
3.94” (100.0 mm)
incl. sunshield
3.46” (88 mm)
22
11.61” (295.0 mm)
10.94” (278.0 mm)
Mounting Template
Figure 11 Mounting Template
Scale 1:1
Mounting screw holes
(8/32 inch diameter)
See “Attaching the Camera” on page 8 for information on using the
mounting template.
Note
The camera enclosure should be mounted on a flat, smooth surface.
Document 800-01802 Rev B
02/09
23
Honeywell Systems Group (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
℡ +1.800.796.2288
Honeywell Systems Group
Northern Europe
Ampérestraat 41
1446 TR Purmerend
The Netherlands
www.honeywell.com/security/nl
℡ +31.299.410.200
Honeywell Systems Group Europe/South
Africa
Aston Fields Road
Whitehouse Industrial Estate
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
℡ +44.01928.754028
Honeywell Systems Group Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
℡ +49.74 31.8 01.0
Honeywell Systems Group Pacific
Unit 5, Riverside Center
24-28 River Road West
Parramatta, NSW 2150, Australia
www.honeywellsecurity.com.au
℡ +61.2.8837.9300
Honeywell Systems Group France
Immeuble Lavoisier
Parc de Haute Technologie
3-7 rue Georges Besse
92160 Antony, France
www.honeywell.com/security/fr
℡ +33.(0).1.40.96.20.50
Honeywell Systems Group Asia
35F Tower A, City Center
100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
℡ +86021.5257.4568
Honeywell Systems Group Italia SpA
Via della Resistenza 53/59
20090 Buccinasco
Milan, Italy
www.honeywell.com/security/it
℡ +39.02.4888.051
Honeywell Systems Group Middle East/
N. Africa
Post Office Box 18530
LOB Building 08, Office 199
Jebel Ali, Dubai, United Arab Emirates
www.honeywell.com/security/me
℡ +971.04.881.5506
Honeywell Systems Group España
Mijancas 1. 3a planta
P. Ind. Las Mercedes
28022 Madrid, Spain
www.honeywell.com/security/es
℡ +34.902.667.800
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-01802 – Rev B – 02/09
© 2009 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by
any means without written permission from Honeywell. The information in this publication is believed to be
accurate in all respects. However, Honeywell cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate such changes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising