Sink Fitting Instructions
INSTALLATION GUIDELINES
Note: Always use a professional installer when fitting our products
BEFORE YOU BEGIN
INSET SINK INSTALLATION
3. Apply the Sealant
A
WARNING: Risk of personal injury. Metal surfaces are sharp and can
•
?
Clean all residue from the top rim of the sink.
cause severe cuts. Use gloves and handle sink edges carefully.
•
?
Clean the underside of the kitchen worktop around the cut-out area and
make sure the surface is smooth and free of defects.
•
?
Apply a generous bead of silicone or latex sealant to the rim of the sink
near the inside edge.
?•
Observe all local plumbing and building codes.
?•
Shut off the hot and cold water supplies.
?•
All information in this guide is based on the latest product information available at
A:Put the clip into the clip
hole as indicated
Clip hole
Clip
B
B:Adjust the clip as direction
the time of publication.
1.Drill a hole at the bottom,then
put the nut into the hole.
RECOMMENDED TOOLS AND MATERIALS
Nut
C
Bottom
C:Tighten the screw
kitchen worktop
•
•
•
•
•
•
•
•
Sink
Pencil and Marker
Measuring Tape
Drill
Scissors
Sealant
Safety Glasses
Keyhole/Compass or jigsaw
Putty Knife
Sealant
Nut
2.Fasten Sink With Screw
Mounting Bracket
Fastener
Fixing Clip
Screw
Sink
3.Install Upper Panel
Upper Panel
Under Mount Sink
Fixing Clip
?
4. Finish the Installation
Undermount Sink Installation
Suggested Clip Placement
(Approximately 8 clips is normally sufficient)
Bottom
Under Mount Sink
•
?
Where a sealant strip is pre fitted to the underside of the sink
please pay close attention to the seal near the corner of the sink.
Often, due to tension on the strip, additional silicone sealant
should be applied on the corners (and elsewhere if required) to
ensure a fully waterproof seal.
• Position and align the sink with the opening in the kitchen worktop. The
?
1. Cut the Sink Mounting Holes
corner of the sink should be flush with the inside edge of the kitchen
CAUTION: Risk of product damage. To avoid damage to the sink, do not
cut , drill, or sand the kitchen worktop while it is positioned over the sink.
worktop.
• Rotate the mounting brackets over the sink rim.
?
•
?
Before cutting, measure the sinks actual dimensions to ensure correct.
•
?
Drill a pilot hole inside the cut-out line.
•
?
Using a jigsaw or keyhole saw, cut along the inside of template if provided.
?
• Tighten each bracket until snug while maintaining proper alignment.
?
Wipe away any excess sealant with a dry cloth.
•
?
Stainless Steel
• Allow the sealant to set for a minimum of 30 minutes. Follow the
?
instructions provided with the sealant.
2. Install the Mounting Brackets(If required)
CARE AND CLEANING
Rinse your stainless steel sink thoroughly after each use, and use a
dabbing action to dry with a clean, soft cloth. Clean your sink once a
week with Bar Keepers Friend or Shiny Sinks.
•
?
Equally space the required number of mounting brackets and locate the
mounting holes on the underside of the kitchen worktop 1-3/8'' (3.5cm) from the
edge of the kitchen worktop opening.
•
?
The type of fastener needed is dependant upon the kitchen worktop material and
should be recommended by the kitchen worktop supplier.
•
?
Loosely install the mounting brackets to the kitchen worktop.
•
?
Turn the brackets parallel to the opening to allow for easy installation of the sink.
Always apply stainless steel cleaner/polish with a nonabrasive cloth or
Kitchen sink made of:
sponge, working with, not across the grain. Do not use steel wool, wire
stainless steel
brushes or abrasive pads to clean your sink.
HPL
Insert (Not Furnished)
Edge kitchen worktop
Opening
Fastener (Not Furnished)
Cleanability: Pass
Crewe,CW1 6EA
Load resistance: N/A
allow cleaners to remain in contact with the sink surface for long
Durability: Pass
periods of time.
EN 13310:2003(13)
Mounting Bracket
1-3/8'' (3.5cm)
±1/4'' (6mm)
If you use cleaners containing bleach, be sure to rinse the surface
12/14 Macon Court,
kitchen worktop Opening Bottom View
HPL,12/14 Macon Court,Crewe,CW1 6EA
immediately after you clean it to avoid corrosion or staining. Do not
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising