DS12R - Bosch Security Systems
DS12R
User Guide
EN
Self-Contained Control
Panel
DS12R | User Guide | Arming Functions
•
1.0 Arming Functions
•
An alarm occurs if any zone is faulted or
after Exit Delay ends.
Exit Delay is the amount of time you have
to exit from the building without causing
an alarm. An alarm occurs if you exit after
Exit Delay ends.
All zones follow Exit Delay if there is at
least one delay zone in the system. If
there are no delay zones, then Exit Delay
is not followed by any zone.
24-Hour zones are always armed. The
arming functions in Section 1.1 through
Section 1.4 do not affect the operation of
24-Hour zones.
The LED for a 24-Hour zone flashes once
every 3 sec, even if the system is
disarmed.
1.1
Arm the System [PIN][ON]
To arm the entire system:
1. Enter the master code or a user code.
2. Press the [ON] key.
• The red Armed LED turns on when the
system is armed.
• The sounder beeps during Exit Delay. The
beep rate increases when only 20 sec remain
in Exit Delay.
• The red Armed LED flashes during Exit
Delay, and then remains on when Exit Delay
ends.
• When Exit Delay ends, the armed zone LEDs
flash once every 3 sec.
You can also use a key fob or a keyswitch to arm the
system.
1.2
Arm the Perimeter [PIN][PERIMETER
ONLY]
To arm only the perimeter zones:
1. Enter the master code or a user code.
2. Press [PERIMETER ONLY].
• The Perimeter LED turns on when the
perimeter is armed.
• If the system has at least one Perimeter Exit
Delay zone, the sounder beeps during Exit
Delay. The beep rate increases when 20 sec
remain in Exit Delay.
2
The red Armed LED flashes during Exit
Delay, and then flashes 2 sec on, and 1 sec off
when Exit Delay ends.
At the end of Exit Delay, the LED for each
armed zone flashes once every 3 sec.
An alarm occurs if any perimeter zone is
faulted during Exit Delay, or after Exit
Delay ends.
You cannot use a key fob to arm the perimeter.
1.3
Arm One or More Zones
[PIN][#][Zone Number]
[#][Zone Number]…[ON]
To arm one or more zones:
1. Enter the master code or a user code.
2. Press [#] followed by a number key to arm a single
zone (1 to 12), then press [ON].
For example, to arm Zone 2, press [#][2][ON].
3. Repeat pressing [#][Zone Number] to arm more
than one zone, then press [On].
For example, to arm Zones 2 and 10, press
[#][2][#][1][0][ON].
• If the system has at least one Delay zone, the
sounder beeps during Exit Delay. The beep
rate increases when only 20 sec remain in Exit
Delay.
• The red Armed LED flashes during Exit
Delay, and then remains on when Exit Delay
ends.
• When Exit Delay ends, the red Armed LED
remains on.
1.4
Quick Arm the System
The installer must enable this function.
To arm the system without entering a code, press and
hold [ON] for 3 sec.
• The sounder beeps during Exit Delay. The beep
rate increases when only 20 sec remain in Exit
Delay.
• The red Armed LED flashes during Exit Delay,
and then remains on when Exit Delay ends.
• When Exit Delay ends, the armed zone LEDs flash
once every 3 sec.
Bosch Security Systems, Inc. | 5/08 | F01U081957-01
DS12R | User Guide | Disarming Functions
.
3.2
2.0 Disarming Functions
If a Delay zone is faulted while the system
is armed, Entry Delay starts.
Entry Delay is the amount of time you
have to disarm the system before an
alarm occurs.
Entry Delay applies only to delay zones.
Instant zones cause an immediate alarm
condition if they are faulted when the
system is armed
You cannot disarm a 24-Hour zone. If a
24-Hour zone is faulted, it always causes
an alarm.
2.1
1.
2.
Disarm the System [PIN][OFF]
Enter the master code or a user code.
Press [OFF].
The system is disarmed when the red Armed or
Perimeter LED is off.
You can also use a key fob or a keyswitch to disarm
the system.
2.2
Disarm One or More Zones
[PIN][#][Zone Number]
[#][Zone Number]…[OFF]
To disarm one or more zones:
1. Enter the master code or a user code.
2. Press [#] followed by a number key to disarm a
single zone (1 to 12), then press [OFF].
For example, to disarm Zones 2, press [#][2][OFF].
3. Repeat pressing [#][Zone Number] to arm more
than one zone, then press [OFF].
For example, to disarm Zones 2 and 1][0, press
[#][2][#][10][OFF].
The system is disarmed when the Armed LED and
the disarmed zone LEDs are off.
3.0 Other Functions
3.1
Special Keys
The installer must enable the special key functions
listed here:
• [A] starts a fire alarm.
• [B] starts a special emergency alarm.
• [C] starts a panic alarm.
To activate a key function, press and hold the key for
3 sec.
Fire Alarm Reset [PIN][Reset]
To return all installed smoke detectors to normal
operation after a fire alarm:
1. Enter the master code or a user code.
2. Press [Reset].
3.3
Cancel Alarm [PIN][OFF]
To stop the alarm output:
1. Enter the master code or a user code.
2. Press [OFF].
3.4
Clear Alarm History
If a zone is faulted and the system is armed, an alarm
occurs. When the system is disarmed, the appropriate
zone LED flashes to identify the faulted zone.
To stop the flashing zone LED, press and hold [#] for
3 sec.
3.5
Bypass One or More Zones
[PIN][Bypass][#][Zone Number]
[#][Zone Number]…[ON]
The installer must enable zone bypassing.
To bypass, or skip, one or more zones when arming
the system:
1. Enter the master code or a user code, then press
[Bypass].
2. Press [#] followed by a number key to bypass a
single zone (1 to 12).
For example, to bypass Zone 8, press [#][8][ON].
3. Repeat pressing [#][Zone Number] to bypass more
than one zone, then press [On}.
For example, to bypass Zones 2 and 10, press
[#][2][#][1][0][ON].
The zone LED for bypassed zones flashes once
every 2 sec.
You cannot bypass a 24-Hour zone.
3.6
Door Unlock Code [PIN][*]
You can use this function only when the
system is disarmed.
The installer must enable this function.
To release a door lock:
1. Enter the master code or a user code.
2. Press [*].
If you have a 4-button key fob, program an option
button to release the door lock. Refer to your key fob
manual for programming instructions.
To reset the function, enter a user code.
Bosch Security Systems, Inc. | 5/08 | F01U081957-01
3
© 2008 Bosch Security Systems, Inc.
F01U081957-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising