Electric Scooter Owner`s Manual

Electric Scooter
Owner’s Manual
Page1
PLEASE BE SAFE WHEN RIDING
ALWAYS WEAR A HELMET AND OBEY ALL LAWS!
IMPORTANT
注意
BATTERY MAINTENANCE and
CHARGING INSTRUCTIONS
You MUST charge completely prior to initial use. (Follow charging
instructions in your Product Handbook)
1. Charge immediately after each use.
2. Charge before storage. You must charge every 30 days if not
in use. Charge the unit for 6-8 hours until the light on the
charger turns green.
3. DO NOT allow this unit to deep discharge the battery.
4. For safety purposes, DO NOT charge for over 8 hours.
5. Turn the unit OFF when not in use.
不
Failure to follow these INSTRUCTIONS will
VOID YOUR WARRANTY!
This PRODUCT IS NOT INTENDED FOR EXTREME or
OFF-ROAD Use! Please take care of your ELECTRIC
SCOOTER!
DO NOT JUMP or ABUSE THIS PRODUCT!
DO NOT RIDE IN WET/ICY CONDITIONS!
The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety
Page2
IMPORTANT
PLEASE READ THIS BEFORE USING THIS PRODUCT
READ THIS FIRST!
WARNING

Persons without excellent vision, balance, coordination, reflex, muscle and
bone strength and good decision-making capabilities should not use this
product.

User: 14+ ages, suggest use the product with adult supervision at all times.

Minors without adult supervision should not use this product.

Persons unwilling or unable to take responsibility for their own actions should
not use this product.

The user of this product assumes ALL risks associated with its use. To
minimize these RISKS, the user must wear safety helmet, goggles, gloves,
elbow and kneepads and appropriate footwear.

This product is ELECTRIC! DO NOT ride this product in wet conditions, puddles
or rainy weather.

Install the fuse before riding.
PACKAGE CONTENTS
Your ELECTRIC SCOOTER comes with the following items in the box. Please
locate all of the following
1.
2.
3.
4.
The ELECTRIC SCOOTER
Battery Charger
Tool Kit
Product Handbook
Page3
GETTING STARTED
Please read and understand these instructions and the OPERATING
PROCEDURES section, prior to starting or riding your ELECTRIC
SCOOTER
Assembly
1. Carefully remove your scooter from the box.
2. Install the front wheel.
3. To unfold the scooter, begin by pressing down on the FOLDING HANDLE with one
hand, while gently pulling up on the handlebars with the other. The handlebar will
snap into place and will not move when secured properly.
4. Loosen the handlebar clamp, and raise the handlebar to the desired height, being
sure the pole snaps into place. Then tighten clamp securely.
5. To attach the handlebars to each side of the t-bar, first loosen the top handlebar clamp
then slide each handlebar into the t-bar being sure they snap into place and are in the
correct orientation for riding. Finish by clamping down the clamp lever securely.
Charging
WARNING: Do not allow your scooter to go into deep discharge, as this will damage the
batteries.
1. Make sure unit is turned off.
2. Open the charging socket located on the right side of the scooter frame, under the
footplate.
3. Locate your Battery Charger. Find the charger socket end that has a
single-prong socket and plug it into the scooter.
4. Next, plug the AC plug into a wall outlet.
When first plugged in, the charger will have one red light that will illuminate, indicating that
the charging process has started. Once the green light on the charger is illuminated, you
may remove the charger and close the safety cap.
Page4
3 Shifts Switch with Power-off protection
1. Turn on: press “ON” shift (When press “ON” shift, the circuit of batteries, controller and
other parts are connected well, then you can operate the scooter in good condition)
2. Power off: press “OFF” shift (When press “OFF” shift, the circuit between batteries and
controller completely disconnected, then achieved the function of protecting the batteries’
lifetime and performance.)
3. Charging: press “CHA” shift (When press “CHA” shift, the circuit between battery and
charging systerm are connected well, but disconnected with the controller systerm, then
the scooter only could be in charging status. In this way, it could be avoid the insecurity
issues caused by the misuse.)
Riding
1. Make sure that all of the exposed bolts and screws are tightened.
2. Raise the kickstand to its upright position.
3. Push the on/off switch (located on the left side of the scooter frame under the footplate)
to the ON position
4. Put one foot on the deck of the ELECTRIC SCOOTER while pushing off with the other
foot, gently rotate the THROTTLE GRIP, on the right side of the handlebars. The
ELECTRIC SCOOTER will begin to move on its own power.
Your scooter has a variable speed hand throttle. You can control the speed of your
scooter by the amount of pressure you use when rotating the hand throttle. The more
you rotate, the faster you will go.
Stopping/Braking
1. To brake, release the THROTTLE GRIP and depress the BRAKE LEVER (on the left
side of the handlebars. Depressing the brake will disengage power to the motor.
When the unit feels like it is loosing power or not accelerating to full speed, the scooter
is ready to be re-charged.
BRAKING SYSTEM
The ELECTRIC SCOOTER uses a hub brake system on the rear wheel. A
hand brake lever on the left side of the handlebar activates the brakes.
Squeezing the hand brake lever with your left hand will activate the rear brake.
Make sure to release the HAND THROTTLE GRIP when engaging the brakes.
ELECTRIC SCOOTER.
Practice braking on a smooth, dry surface to get used to the feel of the braking
system. Braking distance is affected by wet conditions and loose and uneven
riding surfaces.
Page5
Adjusting the Brakes
The Brakes on the ELECTRIC SCOOTER should come fully adjusted from the
factory.
However, it may be necessary to adjust the brakes from time to time.
To adjust the rear brakes:
For brakes that are adjusted too tight
1. Loosen the tension screw on the left
hand brake lever by rotating it
counter-clockwise until the wheel
spins freely.
For brakes that are adjusted too loose
1. Tighten the tension screw on the left
hand brake lever by rotating it
clockwise until the wheel has a slight
drag.
For further adjustment, Locate the
adjustment screw on the rear brake hub
located on the rear wheel.
Squeaky Brakes
The brakes may squeak before they are broken in. This is normal and will not
affect the function or performance of the brakes. With continued use the
squeak should go away.
MAINTENANCE
RECOMMENDED TOOLS
To adjust and service the ELECTRIC SCOOTER you will need the following
tools:
 Allen Wrenches: M5，M2.5
 Wrenches: M13-15，M8-10
 Large Adjustable Crescent Wrench
 Philips Head Screwdrivers
 Oil, Grease or Lubricant
MAINTENANCE SCHEDULE
Proper care of your ELECTRIC SCOOTER will insure optimal performance
and longer life span. The following are a few maintenance suggestions that will
keep your ELECTRIC SCOOTER running in top condition:
Daily Maintenance
Perform each time you ride your ELECTRIC SCOOTER
 Clean the exterior of the unit with a soft, damp rag.
 Check that all nuts and bolts are securely tightened.
 Check battery charger for any frayed/cut wires.
Page6

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project