Motion Detector - Z

Motion Detector - Z
Quick Start Guide
1. Download/Update the Wink App
Visit the iTunes App Store or Google Play Store to download
the latest version of the Wink app. The app will guide you
through some quick steps to sign up or log in.
2. Follow Setup in the Wink App
First, a Wink Hub is required, so be sure that it has already
been connected in the Wink app.
Next, navigate to the Products section and tap the “Add
to Wink” button. Find the Wink Motion Detector and
then follow the instructions in the app to complete the
connection process.
Motion Detector
How to Use—Wall Mount:
How to Use—Table Top:
You can mount the Motion Detector on any wall with a
central line-of-sight perspective of the area you wish
to monitor. It is best to mount the Motion Detector as
high as possible to avoid limiting its effective range with
obstacles like tables and chairs.
You can use the facet on the sensor body to properly
angle the Motion Detector on a table top or bookshelf to
monitor a room.
1.
Remove the magnetic cradle and store it for later use
if needed.
2. Make sure your device is powered on and within
range of the Wink Hub.
3. Place the sensor body on a horizontal surface with an
unobstructed view of the area you wish to monitor.
Installation—With Double Stick Tape:
1. Wipe your wall clean of any dirt and grease.
2. Peel-and-stick the magnetic cradle to your wall using
the included double-stick tape.
3. Place the sensor body on the magnetic cradle at
an angle to properly monitor your room, and the
magnet will hold the sensor body in place.
Installation—With Screws:
1. Twist the mount counterclockwise to separate the
magnet from the wall mount.
2. Hold the wall mount to your wall and drive the
included screws through the screw holes.
3. Reattach the magnet to the wall mount.
4. Place the sensor body on the magnetic cradle at
an angle to properly monitor your room, and the
magnet will hold the sensor body in place.
Including/Connecting into the Z-Wave Network:
Follow the instructions for your Z-Wave certifed
Controller to enter inclusion mode.
When prompted by the Controller:
1. For proper inclusion, bring the Motion Detector
within range of your Controller.
2. Pull the tab on the side of the sensor to power on,
or remove then re-install the batteries.
The LED indicator will flash five times indicating
inclusion.
Excluding/Disconnecting from the Z-Wave Network
Follow the instructions for your Z-Wave certified
Controller to enter exclusion mode. When prompted by
the Controller:
1. Remove the sensor cover by twisting it
counterclockwise and be sure it is powered on.
Resetting the Motion Detector to Factory Settings:
To disconnect from the Z-Wave Network and restore
factory default settings:
1.
Remove the sensor cover by twisting it
counterclockwise and be sure it is powered on.
2. Press the Connect Button on the bottom of the
device next to the battery quickly 3 times in a row.
2. Hold the Connect Button next to the battery for 10
seconds until the LED indicator blinks once, then
release the button.
The LED Indicator will flash five times indicating
exclusion/disconnection.
Only do this if the controller is disconnected or
otherwise unreachable!
NEED HELP? CONTACT WINK CUSTOMER SERVICE
CORRECT DISPOSAL OF BATTERIES IN THIS PRODUCT
Visit wink.com/help, or shoot us an email at questions@wink.com.
Want to speak to a human? Reach us at 1-844-WINK-APP
This marking on the product, accessories or literature indicates that the product and
its electronic accessories should not be disposed of with other household waste.
WARRANTY
For warranty information regarding this product, visit www.wink.com/returns
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
US COMPLIANCE STATEMENT (FCC)
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Model: WNK-MOT1
FCC: 2ACAJ-WMOT1
Tested to Comply with FCC Standards
FOR HOME OR OFFICE USE
CANADA COMPLIANCE STATEMENT (IC)
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. Son exploitation est autorisée aux deux conditions suivantes:
(1) il ne doit pas produire de brouillage; et (2) il doit accepter tout brouillage radioélectrique subi, même si celui-ci est susceptible d’en compromettre le fonctionnement.
IC: 11938A-WMOT1
Household users should contact either the retailer where they purchased this product,
or their government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed
with other wastes for disposal.
This marking on the battery, manual or packaging indicates that the batteries in this
product should not be disposed of with other household waste. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or
lead above the reference levels in EC Directive 2006/66. If batteries are not properly
disposed of, these substances can cause harm to human health or the environment.
©2017 Wink Labs, Inc. All rights reserved
606 W 28th St., Floor 6
New York, NY 10001
www.wink.com
Z-Wave Lifeline and Association Groups
Group
Maximum nodes
Description
1 - Z-Wave Lifeline
5
Group 1 is the “Lifeline”
group, which can hold five
devices. The Motion
Detector sends this group a
Notification Report and
Binary Sensor Report
whenever motion is detected
and when it stops. It also
sends a Multilevel Sensor
Report incrementally based
on time (see Param 7,) or
when a relative change in
light level is detected (see
Param 9.) Finally, the Motion
Detector sends this group
Battery Reports and a Device
Reset Locally notification to
remove itself from the
Z-Wave network.
2
5
The Motion Detector sends a
BASIC_SET command to
Association Group 2 to
directly trigger devices (like a
siren, chime, etc.) when
motion is detected and when
it stops. Optionally, the
Motion Detector can be set to
only send this when ambient
light levels fall below a
predetermined level (see
Configuration Parameters 5
and 8.) See Configuration
Parameters 2, 3, 5, and 8 for
more details regarding
Association Group 2.
3
5
Group 3 supports up to 5
members and the Motion
Detector sends it a
NOTIFICATION_REPORT
when motion is detected and
when it stops.
4
5
Group 4 supports up to 5
members and the Motion
Detector sends it a
SENSOR_BINARY_REPORT
when motion is detected and
when it stops.
Configuration Parameters
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising