Compass

Compass
▼
Table of Contents
▲
Main Menu
Compass
Compass Calibration
The compass may need to be
manually calibrated after exposure to
a strong magnetic field. If the
compass seems to continually show
the wrong direction, do this.
NOTE: Do this procedure in an open
area, away from buildings, power
lines, and other vehicles.
1. With the blue center icon
displayed, press and hold the
compass button for about 6
seconds. When the center icon
turns red, release the button.
2. Drive the vehicle slowly in circles
at less than 5 mph (8 km/h) until
the center icon turns blue. This
icon also turns blue by continuing
to drive the vehicle under normal
driving conditions. When you see
an actual heading on the compass,
calibration is completed.
Compass Zone Selection
In most areas, there is a variation
between magnetic north and true
north. Zone selection is required so
the compass can compensate for this
variation. To check and select the
zone, do this:
1. Find the zone for your area on the
zone map (see page 179 ). Each
zone number (1 through 15)
corresponds to a compass zone on
the table (see page 179 ).
178
2. Press and hold the compass
button for about 3 seconds. When
all of the direction icons begin to
blink, release the button.
3. The blue direction icon(s) blink
and show the current zone.
4. If the zone is incorrect, press and
release the compass button
repeatedly to get to the correct
number.
5. The compass will return to the
normal display about 4 seconds
after you stop adjusting a zone
number.
▼
Table of Contents
▲
Main Menu
Compass
Zone Map
Compass Display for Each Zone
Features
179
Rearview Camera and Monitor
On EX-L models with navigation system
REAR VIEW CAMERA
Whenever you shift to R (reverse)
with the ignition switch in the ON
(II) position, the rear view is shown
on the navigation or Compass
system screen.
For the best picture, always keep the
rearview camera clean, and do not
cover the camera lens. To avoid
scratching the lens when you clean it,
use a moist, soft cloth.
180
When in reverse, the touch screen
and navigation system ‘‘hard’’
buttons are locked out, except the
‘‘ZOOM’’ button. Touching the ‘‘▼’’
or ‘‘▲’’ button allows you to adjust
the brightness of the rearview
camera image.
The camera brightness cannot be
adjusted by voice control.
Since the rearview camera display
area is limited, you should always
back up slowly and carefully, and
look behind you for obstacles.
▼
Table of Contents
▲
Main Menu
▼
Table of Contents
▲
Main Menu
HomeLink Universal Transceiver
If equipped
General Information
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor for that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected.
If your garage door opener was
manufactured before April 1982, you
may not be able to program
HomeLink to operate it. They do not
have the safety feature that causes
the motor to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury.
Important Safety Precautions
Always refer to the opening
instructions and safety information
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this information,
contact the manufacturer of the
equipment.
For quick and accurate training,
make sure the remote transmitter
for the device (garage door,
automatic gate, security system, etc.)
has a fresh battery.
Training HomeLink
Before you begin − If you just
received your vehicle and have not
trained any of the buttons in
HomeLink before, you should erase
any previously learned codes before
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 25 seconds,
until the red indicator flashes.
Release the buttons, then proceed to
step 1.
If you are training the second or
third buttons, go directly to step 1.
1. Unplug the garage door opener
motor from the electrical outlet.
2. Hold the end of the garage door
opener remote transmitter 2 to 5
inches from HomeLink. Make
sure you are not blocking your
view of the red indicator in
CONTINUED
HomeLink.
181
Features
The HomeLink universal
transceiver built into your vehicle
can be programmed to operate up to
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
▼
Table of Contents
▲
Main Menu
HomeLink Universal Transceiver
If the red indicator in HomeLink
continues to flash slowly (does
not flash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4.
3. Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time.
If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5.
4. Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds.
If the red indicator in HomeLink
begins to flash slowly at first,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
continues to flash slowly (does
not begin to flash rapidly),
repeat steps 2 thru 4.
5. Plug in the garage door opener
motor, then test the HomeLink
button by pushing it for about 1
182
second.
If the button works,
programming is complete.
If the button does not work go
to step 6.
6. Push and hold the HomeLink
button for a few seconds, then
watch the red indicator on
HomeLink.
If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
If the indicator flashes rapidly
for 2 seconds then stays on, you
have a rolling code transmitter:
go to ‘‘Training with a Rolling
Code System’’ (see page 183 ).
7. Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled device around
your home (lighting, automatic
gate, security system, etc.).
▼
Table of Contents
▲
Main Menu
HomeLink Universal Transceiver
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The following procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes.
1. Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
TRAINING BUTTON
4. Press and hold the button on
HomeLink for 3 to 4 seconds.
5. Press and hold the HomeLink
button again for 3 to 4 seconds.
This should turn off the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
3. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
come on and stay on. You then
have approximately 30 seconds to
complete the following steps.
6. Press the HomeLink button again
for about 1 second. It should
operate the garage door.
2. Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer.
183
Features
Training With a Rolling Code
System
For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed before
HomeLink can operate the garage
door opener.
▼
Table of Contents
▲
Main Menu
HomeLink Universal Transceiver
Erasing Codes
To erase the codes stored in all three
buttons, press and hold the two
outside buttons until the red
indicator begins to flash, then
release the buttons.
You should erase all three codes
before selling the vehicle.
Retraining a Button
If you want to retrain a programmed
button for a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure:
1. Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.
If a rolling code transmitter was
previously programmed, the
indicator will flash rapidly for 2
seconds, and then stay on for
about 23 seconds.
184
If a standard transmitter was
programmed, the indicator will
stay on for about 25 seconds.
2. Once the HomeLink indicator
begins to flash slowly, continue to
hold the HomeLink button, and
follow steps 3 thru 6 under
‘‘Training HomeLink’’ (see page
181 ).
Customer Assistance
If you have problems with training
the HomeLink Universal Transceiver,
or would like information on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com.
HomeLink is a registered
trademark of Johnson Controls, Inc.
As required by the FCC:
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s
authority to operate the equipment.
This device complies with Industry
Canada Standard RSS-210.
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference that may cause
undesired operation of the device.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising