Quattro Micro Battery Charger Manual

Quattro Micro Battery Charger Manual
INSTRUCTION MANUAL
QUATTRO MICRO BATTERY CHARGER
SK-100079
INTRODUCTION
Thank you for your choice of the SKYRC Quattro Micro Battery Charger. This unit is
simple to use but its operation does require some knowledge on the part of the user.
Please read this entire operating manual completely and attentively before using this
product, as it covers a wide range of information on operating and safety.
SKYRC Quattro Micro Battery Charger employs the circuit that features four totally
independent but identical power outputs which are powered 4W each. It is designed for
charging single cell LiPo. Insert the battery lead to the right connector in each port, the
charger will charge 4 batteries at the same time. And the charging current can be
adjusted from 0.1-1A by dial, the charging capacity and cell voltage can be displayed in
each 4-digital LED Indicators.
Micro Reverse
DC Input
Power Jack
11-15V
mCPX
Micro
MX
4-Digital LED
Indicator
Charging Status
LED Indicator
AC Input
Power Port
100-240V
Rotary Dial
for Setting
Charging Current
Start/Stop
Button
1
FEATURES
Four independent ports can be used at the same time
Four different kinds of battery connectors in each port
Four independent functioning charging circuits
Four independent 4-digital LED displays current and capacity
LED and audible sound indicate charging status
Adjustable charging current from 0.1-1A
AC/DC Dual Power Input
Efficient ventilation
Maximum protection: short circuit protection; over current protection; battery reverse
polarity protection and DC input voltage protection
CHARGE PROCEDURES
Getting Started
When using 12V lead acid battery,
Using DC cable
attaching to car
battery
When using AC power source
1. Insert the AC power cord into the charger.
2. Insert the AC power cord into a wall socket (100-240V).
3. When the charger is powered on, 4 status LEDs will blink once with one beep and all
4-digital LED Indicators will display 8888. After that, 4 LEDs will extinguish and all 4digital LED Indicators will display the charging current which indicates the charger is
ready to charge.
Caution: Each charging port can only charge one kind battery at same time.
2
OPERATING
1.
Insert
the battery lead to the right battery connector.
Note: Please make sure insert the battery polarities correctly.
2.
Select
the charging current (0.1-1A) by rotating the dial.
Note: You are not able to adjust the charging current during charging process.
3.
Press
and hold START/STOP button for 3 seconds to start charging process. The related status
LED will turn red with long beep.
4.
During
the charging process, the 4 digital LED will display charging capacity, battery voltage and
charging current circularly.
Charging Capacity(mAh)
Battery Voltage(V)
Charging Current(A)
5. LED will stay red during the whole charging process.
The
6.
Press
and hold START/STOP button for 3 seconds during charging process to stop charging.
7. When the charging process is finished, the status LED turn green and blinks 5 times with audible
sound. And the status LED stays green and the 4-digital LED will display “FULL”.
Note: At this time, if you press the “START/STOP” button once, the 4-digital LED will display “FULL”, battery voltage
and battery capacity circularly.
Battery Voltage(V)
Charging Capacity(mAh)
4 DIGITAL LED MESSAGE DISPLAY
Charging Capacity(mAh)
Battery Voltage(V)
Charging Current(A)
(0.10-1.00A)
Status: Charging process finish.
3
ERROR MESSAGE
When there is an error, the LED will blink red twice per second with audible sound. After ten
times of blink, the read LED will stay on and the 4-digital LED will display the error code,
Error Code
Error Message
-11-
Dead cell or voltage of cell is too high or too low for safe charging.
-22-
The battery polarity is connected incorrectly.
-33-
The battery connection is wrong.
-44-
Short circuit or over current in the battery.
-55-
The DC input voltage is too high or too low.
SPECIFICATION
AC Input
100-240V
DC Input
11-15V
Charge circuit power
4X4W ±10%
Charge current range
0.1-1.0A ±10%
Battery type
4X1 cell LiPo
Battery connector type
Micro / Micro Reverse/
MX / mCPX
Working temperature
0-50℃
Net weight
280g
Dimension
132x100x50mm
WARRANTY AND SERVICE
We guarantee this product to be free of manufacturing and assembly defects for a period
of one year from the time of purchase. The warranty only applies to material or
operational defects, which are present at the time of purchase. During that period, we will
repair or replace free of service charge for products deemed defective due to those
causes.
For any repair or replace service, please contact your dealer in the first instance, who is
responsible for processing guarantee claims. This warranty is not valid for any damage or
subsequent damage arising as a result of misuse, modification or as a result of failure to
observe the procedures outlined in this manual.
RoHS
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
7504-0412-02
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement