CheckVideo High Definition Indoor Micro Dome Camera Installation

CheckVideo High Definition Indoor Micro Dome Camera Installation
CheckVideo High Definition Indoor Micro Dome Camera
Installation Quick Reference
Things You Need for Installation
If this CheckVideo device will be monitored by a central station, please contact the central station for a username and password on their existing
CheckVideo account. The central station will add the device to their account.
If this device will be self-monitored, you will be adding it to your CheckVideo account. If you do not have an account, contact CheckVideo support.
Included in the box:
You’ll also need:
•
CheckVideo® HD Dome Camera
•
•
Bag of mounting parts: screws (5), drywall
mounts (5), hex wrench, 2 Phoenix connectors
PC or Mac® with Broadband Internet
Service
•
Router, connected to the Internet
•
128GB MicroSD card, pre-inserted
•
Phillips screwdriver
•
Power Over Ethernet (PoE) injector (recommended for testing only)
•
Cat-5 network cables
•
DC 12-48v power supply (optional)
•
Camera cabling giude
Step One Connect Camera to Router
1. For later reference, enter the device’s serial number in the box below. Also known as MAC, this number is found on the underside of the
camera:
2. Before installing the camera in its final location, power the camera and connect it to the network. If your router supports PoE, connect the
camera to a PoE port via a Cat-5 network cable. Otherwise, connect the camera to an open port on the router and use a DC 12-48V power
supply to power the camera. Note: Ethernet cable runs can be no longer than 100 meters.
3. If using the PoE injector, connect the router or switch to “Data In” on the injector and connect the injector’s “Data & Power Out” port to the
camera using Cat-5 network cables. Connect the injector to a power outlet.
Step Two Add CheckVideo HD Camera
1.
If camera will be monitored by a central station, contact
them to add the device to their account.
2.
If self-monitored, go to the CheckVideo Dashboard via
login page: portal.checkvideo.net
3. On the CheckVideo Dashboard, click on Devices > Add
Device
4. In the Register Device section, enter the MAC ID found on
the underside of the camera and create a Device Name.
5. Click the Test Device button to make sure the CheckVideo Software Service (CVSS) can communicate with the
device.
6. When prompted, update the device firmware.
Fig. 1 - Add Device: Enter device serial number
Step Three Install Camera
To optimize event detection, place your CheckVideo HD Camera
as follows:
•
HEIGHT: Each camera must be installed 8 to 20 feet off the
ground.
•
DISTANCE: If you are mainly detecting people, the distance
between the camera and the people you wish to detect
should be 10 to 100 feet. If you are primarily concerned with
detecting vehicles, the range is 30 to 160 feet.
,
Fig. 2 - MORE EFFECTIVE: Cameras
are at a 15 to 45 degree downward
tilt and are mounted 8 to 20 feet high
The CheckVideo Camera Placement Guide includes a summary
checklist on improving your camera placement.
Once you’ve determined where to place the Camera, run Cat-5
network cable from the router to the desired location. The
Camera can be placed on a ceiling or wall.
Ball
To adjust the camera to the proper angle, remove the cover using
the included hex wrench. This will expose the ball and lens. The
ball rotates in 3 directions. Gripping the ball, adjust the angle for
your location, seeking to maintain a 15 to 45 degree downward
tilt. Be careful not to touch the lens as rotating it will change the
focus and may result in fingerprints on your video images.
Using the mounting screws, attach the camera to the wall or
ceiling and reattach the cover using the previously removed hex
screws. Remember to pay attention to the microSD card, being
careful to avoid pressing on it with the camera's cover.
Fig. 3 - LESS EFFECTIVE: Cameras are
directly overhead (90 degrees) or parallel
to (0 degrees) the target
MicroSD
Card
Fig. 4 - Remove the cover using the
supplied hex wrench
Fig. 5 - Rotate the lens to achieve the
proper viewing angle.
Power up the camera (refer to Step 1 for additional information).
Step Four Configuration
1.
On the CheckVideo Dashboard, click on Devices >
Configure Device.
2. Select Device: Select the device and video resolutions
for event clips and DVR. CheckVideo will default both
resolutions to 720p. You may wish to start with these
settings. Your chosen resolution settings will depend
upon the upload capacity of your Internet provider.
3. Configure Events: Click the Edit button to create a
zone for a particular object type. Then use your mouse
to draw the zone by clicking the left mouse button
wherever you want to define a point of the zone. The
zone should cover the entire area where you want to
detect an event. Enter a time span, event type, zone,
and duration and click Add Event button.
Fig. 6- Rotate Image button
Make sure your browser is set to 100% when drawing
your zone.
4. Select Notification Method - Central Stations: Select a
Central Station type that should receive alert metadata.
5.
Select Notification Method - Users: Click the checkbox
next to any user(s) who should receive notifications for
this camera and their method of notification.
6. Click Save.
Lens
Fig. 7a - A zone, defined by eight end points
(first point is green; other points are blue)
Fig. 7b - A completed zone
For more detailed information, refer to the CheckVideo HD Indoor Micro
Dome Camera Installation Guide available at www.checkvideo.com.
© 2017 CheckVideo, LLC
CheckVideo is a registered trademarks of CheckVideo, LLC. All rights reserved.
7CVCHQC000E-01.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement