Neon Flex User Manual

Neon Flex User Manual
Neon Flex User Manual
IP68 SLW LED® FLEX NEON
(PRO-RGB-DMX)
Sign Lighting World
3265 Walnut St, Boulder, CO 80301
[email protected]
720-242-9000
www.SLWLED.com
Table of Contents
LED Flex Neon PRO........................................................................................................................................ 3
A.
Specification ...................................................................................................................................... 3
B.
Photometric Parameters ................................................................................................................... 4
C.
Connection Length ............................................................................................................................ 5
D.
Bending Direction ............................................................................................................................. 6
E.
Mounting........................................................................................................................................... 6
F.
Connection ........................................................................................................................................ 6
G.
PRECAUTIONS ................................................................................................................................... 7
H.
Accessory Assembling ....................................................................................................................... 8
RGB LED Flex Neon...................................................................................................................................... 12
A.
Specification .................................................................................................................................... 12
B.
Photometric Parameters ................................................................................................................. 12
C.
Bending Direction ........................................................................................................................... 13
D.
Mounting......................................................................................................................................... 13
E.
Connection ...................................................................................................................................... 13
F.
PRECAUTIONS ................................................................................................................................. 16
G.
Accessory Assembling ..................................................................................................................... 18
DMX LED Neon Flex..................................................................................................................................... 21
A.
Specification .................................................................................................................................... 21
B.
Photometric Parameters ................................................................................................................. 21
C.
Bending Direction ........................................................................................................................... 22
D.
Mounting......................................................................................................................................... 22
E.
Connection ...................................................................................................................................... 22
F.
PRECAUTIONS ................................................................................................................................. 24
G.
Accessory Assembling ..................................................................................................................... 25
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
LED Flex Neon PRO
The products are widely used in the illumination and decorative lighting for piazza, restaurants, private
villas, gardens, conference rooms, exhibition halls, stage bars, shopping malls, parking structures, and
tourist attractions.
A. Specification
1. Structure
Material: PVC Body
Input Voltage: 24VDC
LED Qty/m: 60pcs
Protection: IP68*
Work Temperature: -22F – 113F (-30C to 45C)
IK Class: IK08
2. Model Configuration Table
Model NO.
LED Color
F21A-24V
Y/G/B/WW/W/NW 6 pcs
SMD/5050
R/O
10pcs
SMD/5050
Y/G/B/WW/W/NW 6pcs
SMD/5050
R/O
10pcs
SMD/5050
F21A-24V
F15A-24V
F15A-24V
LEDs/Unit
Cutting
Length
4in (10cm)
Power/m
Weight
12W
6.5in
(16.67CM)
4in (10cm)
7.2W
6.5in
(16.67CM)
7.2W
1lb/3.28ft
0.5kg/m
1lb/3.28ft
0.5kg/m
.8lb/3.28ft
0.38kg/m
1.5lbs/3.28ft
0.68kg/m
12W
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
B. Photometric Parameters
1. Model: F21A-6000K
Figure 1: Cadela Distribution
Figure 2: Illuminance at a Distance
Figure 3: Integrating Sphere Measurement
Photo Parameters:
Render Index: Ra = 71.2
Flux = 246.7 lm
Eff.: 22.20 lm/W
Fe = 732.8 mW
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
2. Model: F15A-6500K
Figure 4: Cadela Distribution
Figure 5: Illuminance at a Distance
Figure 6: Integrating Sphere Measurement
Photo Parameters:
Render Index: Ra = 71.7
Flux = 302.3 lm
Eff.: 27.99 lm/W
Fe = 909.8 mW
C. Connection Length
Power at one end: 10M
Power at both ends: 20M
Customized Length
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
D. Bending Direction
The minimum bending diameter is 3.15in (8cm).
E. Mounting
Every meter of aluminum channel has 2 screw holes. The installation usually requires installing
aluminum channel as the first step, and then insert the LED neon product to the channel.
F. Connection
The use of LED neon requires a 24V constant voltage power supply.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
G. PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not over extend the min. & max. bend radius.
Although products do not generate a great amount of heat, it is recommended that you do
not cover or conceal it
Do not route LED flex neon through walls, doors, windows, or building structures.
Do not roll out LED flex neon on rough surfaces and over sharp corners. This will scratch the
PVC optic.
Do not use the product if outer PVC jacket is damaged, loose connections, or if the wire is
visible without insulation.
Do not secure the product with staples, nails, or like means that might damage the
insulation or PVC material.
Do not install LED flex neon on/in places where it is subject to continuous flexing.
Do not operate/run LED flex neon in temperatures exceeding 115F (45C).
Do no operate LED flex neon over the specified voltage or LED life degradation will be
greatly increased.
Do not leave any part of the LED flex neon unsecured. Movement over time from weather
can cause damage from continuous movement.
Always place 100% silicone inside every connection before assembly.
All LED neon IP68 rated connectors must be assembled properly to obtain rating.
Do not reverse polarity when connecting from both ends. This will damage the internal PCB
board. Always test connections with your multi-meter.
Do not energize LED flex neon in reel package.
LED flex neon can be cut only where marked. Look for “Dotted Line” or “Scissor Mark.”
Cutting outside the specified mark will damage the light.
Do not cut while the LED flex neon is connected with power.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
Figure 7: Light Surface
Figure 8: Accessory Attachment
Figure 9: Cutting Precautions
H. Accessory Assembling
1. Front Connector
1. Place the anti-skidding clip on
the very end of the tubing with
the 2 tiny tabs that are pointing
inwards still touching the end of
the material and crimp in place.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide on
over the anti-skidding clip. Put
100% clear silicone on the end of
the Neon Flex tube material
covering the circuit board
completely before proceeding to
step 5. This is to ensure a
waterproof seal. Failure to
properly seal and assemble as
instructed may void warranty.
5. After putting silicone onto the
end of the Neon Flex tube
material, place the rubber gasket
on the end of the tube.
6-7. Insert your front connector
so the connector pins are in the
narrow edge of the connection
point.
8. Screw the front connector to
the aluminum mounting piece.
9. Check the connection to
ensure it is tight and that there
are no gaps between the Neon
Flex tube and the front
connector.
2. End Connector
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
1. Place the anti-skidding clip
on the very end of the tubing
with the 2 tiny tabs that are
pointing inwards still
touching the end of the
material and crimp in place.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide
on over the anti-skidding
clip. Put 100% clear silicone
on the end of the Neon Flex
tube material covering the
circuit board completely
before proceeding to step 5.
This is to ensure a
waterproof seal. Failure to
properly seal and assemble
as instructed may void
warranty.
5. Place the rubber gasket on
the end of the tube.
6. Place the tail plug over the
rubber gasket.
7. Screw the tail plug to the
aluminum mounting piece.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
8. Check the connection to
ensure it is tight.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
RGB LED Flex Neon
A. Specification
1. Structure
Material: PVC body
Input Voltage: 24VDC
LED Qty/m: 60pcs
Protection: IP68
Work Temperature: -22F – 113F (-30C to 45C)
IK Class: IK08
2. Model Configuration Table
Model NO.
LED Color
LEDs/Unit
F21RGB
RGB
F15RGB
RGB
10pcs
SMD/5050
10pcs
SMD/5050
Cutting
Length
6.5in
(16.67cm)
6.5in
(16.67cm)
Power/m
Weight
12W
1.17lbs/3.28ft
0.53kg/m
.8lb/3.28ft
0.38kg/m
12W
B. Photometric Parameters
1. Model: F21RGB
B-1. Wave Length: Red 623.5nm, Green 522.8nm, Blue 469nm
B-2. Lumen Output: F21RGB – Red 18lm/m, Green 64lm/m, Blue 16lm/m
B-3. Lumen Output: F15RGB – Red 20lm/m, Green 71lm/m, Blue 17lm/m
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
C. Bending Direction
The minimum bending diameter is 3.15in (8cm).
D. Mounting
E. Connection
1. Connection with common RGB controller, 10 m max. for single length.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
2. Connection with common RGB controller, extended by using power repeater.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
3. Connection with DMX decoder and DMX controller.
4. Connection with CTR-RGB-24V, this controller has 350W Meanwell power
supply and DMX decoder built in.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
F. PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not over extend the min. & max. bend radius
Although products do not generate a great amount of heat, it is recommended that you do not
cover or conceal it.
Do not puncture, cut, shorten, or splice LED neon outside of the designated cutting marks.
Do not route LED flex neon through walls, doors, windows, or building structures.
Do not roll out LED flex neon on rough surfaces and over sharp corners. This will scratch the
PVC optic.
Do not secure the product with staples, nails, or like means that might damage the insulation of
PVC material.
Do not use the product if outer PVC jacket is damaged, loose connections, or if wire is visible
without insulation.
Do not install LED flex neon on/in places where it is subject to continuous flexing.
Do not operate/run LED flex neon in temperatures exceeding 115F (45C).
Do not operate LED flex neon over the specified voltage or LED life degradation will be greatly
increased.
Do not leave any part of the LED flex neon unsecured. Movement over time from weather can
cause damage from continuous movement.
All LED neon IP68 rated connectors must be assembled properly to obtain rating.
Do not reverse polarity when connection from both ends. This will damage the internal PCB
board. Always test connections with your multi-meter.
Do not energize LED flex neon in the reel package.
LED flex neon can be cut only where marked. Look for “Dotted Line” or “Scissor Mark.” Cutting
outside of the specified mark will damage the light.
Do not cut while the LED flex neon is connected with power.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
Figure 10: Light Surface
Figure 11: Accessory Attachment
Figure 12: Cutting Precautions
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
G. Accessory Assembling
1. Front Connector
1. Place the anti-skidding clip on
the very end of the tubing with
the 2 tiny tabs that are pointing
inwards still touching the end of
the material and crimp in place.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide on
over the anti-skidding clip. Put
100% clear silicone on the end of
the Neon Flex tube material
covering the circuit board
completely before proceeding to
step 5. This is to ensure a
waterproof seal. Failure to
properly seal and assemble as
instructed may void warranty.
5. Place the rubber gasket on the
end of the tube.
6-7. Insert your front connector
so the connector pins are in the
narrow edge of the connection
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
point.
8. Screw the front connector to
the aluminum mounting piece.
9. Check the connection to
ensure it is tight.
2. End Connector
1. Place the anti-skidding clip
on the very end of the tubing
with the 2 tiny tabs that are
pointing inwards still
touching the end of the
material and crimp in place.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide
on over the anti-skidding
clip. Put 100% clear silicone
on the end of the Neon Flex
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
tube material covering the
circuit board completely
before proceeding to step 5.
This is to ensure a
waterproof seal. Failure to
properly seal and assemble
as instructed may void
warranty.
5. Place the rubber gasket on
the end of the tube.
6. Place the tail plug over the
rubber gasket.
7. Screw the tail plug to the
aluminum mounting piece.
8. Check the connection to
ensure it is tight.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
DMX LED Neon Flex
A. Specification
1. Structure
Material: PVC Body
Input Voltage: 24VDC
LED Qty/m: 56pcs
Protection: IP68
Work Temperature: -22F – 113F (-30C to 45C)
IK Class: IK08
Pixel/m: 8 pixels
IC Model: WS2821
DMX address: Writeable
Max Length: 7m (power at one end)
15m (power at both ends)
2. Model Configuration Table
Model No.
F21DMX
LED Color
Pixel RGB
F15DMX
Pixel RGB
LEDs/Unit
7pcs
SMD/5050
7pcs
SMD/5050
Cutting Length
5in (12.5cm)
Power/m
12W
5in (12.5cm)
12W
Weight
1lb/3.28ft
0.5kg/m
.8lb/3.28ft
0.38kg/m
B. Photometric Parameters
1. Model: F21DMX
B-1. Wave Length: Red 623.5nm, Green 522.8nm, Blue 469nm
B-2. Lumen Output: F21RGB: Red 17lm/m, Green 60lm/m, Blue 15lm/m
B-3. Lumen Output: F15RGB: Red 19lm/m, Green 66lm/m, Blue 16lm/m
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
C. Bending Direction
The minimum bending diameter is 3.15in (8cm).
D. Mounting
Every meter of aluminum channel has 2 screw holes. The installation usually requires installing
aluminum channel as the first step, and then inserting the LED neon product to the channel.
E. Connection
1. Wire Illustration
i.
ii.
Bare Wire
With DMX Console
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
2. Write Address
The DMX LED neon address is present to 001 in factory. The address writer is needed to write
new address when users cut new or use specially.
After connection, press the
button until the whole DMX LED neon shows white. This means
the address is written successfully with start from 001.
3. Connection with DMX Controller LT-800. This controller can only take 170
pixels.
Connection Length: 7m
Connection Length: 15m
Connection Length: more than 15m
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
4. Connection with specialized controller K-8000D. This controller has 8
outputs, each output can take 512 pixels. That means each output can take
60m of DMX LED neon. It has 32 kinds of built-in effects. This controller also
has function of writing address.
F. PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not over extend the min. & max. bend radius.
Although products do not generate a great amount of heat, it is recommended that you do not
cover or conceal it.
Do not puncture, cut, shorten, or splice LED neon outside of the designated cutting marks.
Do not route LED flex neon through walls, doors, windows, or building structures.
Do not roll out LED flex neon on rough surfaces and over sharp corners. This will scratch the
PVC optic.
Do not use the product if outer PVC jacket is damaged, loose connections, or if wire is visible
without insulation.
Do not secure the product with staples, nails, or like means that might damage the insulation or
PVC material.
Do not install LED flex neon on/in places where it is subject to continuous flexing.
Do not operate/run LED flex neon in temperatures exceeding 115F (45C).
Do not operate LED flex neon over the specified voltage or LED life degradation will be greatly
increased.
Do not leave any part of the LED flex neon unsecured. Movement over time from weather can
cause damage from continuous movement.
All LED neon IP68 rated connectors must be assembled properly to obtain rating.
Do not reverse polarity when connecting from both ends. This will damage the internal PCB
board. Always test connections with your multi-meter.
Do not energize LED flex neon in the reel package.
LED flex neon can be cut only where marked. Look for “Dotted Line” or “Scissor Mark.” Cutting
outside of the specified mark will damage the light.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
•
Do not cut while the LED flex neon is connected with power.
Figure 13: Light Surface
Figure 14: Accessory Attachment
Figure 15: Cutting Precautions
G. Accessory Assembling
1. Front Connector
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
1. Place the anti-skidding clip on
the very end of the tubing with
the 2 tiny tabs that are pointing
inwards still touching the end of
the material and crimp in place.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide on
over the anti-skidding clip. Put
100% clear silicone on the end of
the Neon Flex tube material
covering the circuit board
completely before proceeding to
step 5. This is to ensure a
waterproof seal. Failure to
properly seal and assemble as
instructed may void warranty.
5. Place the rubber gasket on the
end of the tube.
6-7. Insert your front connector
so the connector pins are in the
narrow edge of the connection
point.
8. Screw the front connector to
the aluminum mounting piece.
9. Check the connection to
ensure it is tight.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
2. End Connector
1. Place the anti-skidding clip
on the very end of the tubing
with the 2 tiny tabs that are
pointing inwards still
touching the end of the
material and crimp in place.
2-4. Line up the aluminum
mounting piece so the screw
holes face the plug and slide
on over the anti-skidding
clip. Put 100% clear silicone
on the end of the Neon Flex
tube material covering the
circuit board completely
before proceeding to step 5.
This is to ensure a
waterproof seal. Failure to
properly seal and assemble
as instructed may void
warranty.
5. Place the rubber gasket on
the end of the tube.
6. Place the tail plug over the
rubber gasket.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
7. Screw the tail plug to the
aluminum mounting piece.
8. Check the connection to
ensure it is tight.
Product is IP68 rated when assembled according to instructions in user manual, if not assembled per
instructions, warranty may be voided.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement