Network Dome Camera Quick Guide

Network Dome Camera Quick Guide
1
Quick Guide of Network Dome Camera
Network Dome Camera
Quick Guide
V3.0.0
Hangzhou Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com
2010-04
1
Quick Guide of Network Dome Camera
1.Camera Physical Description
Serial NO.
Description
1
LAN(PoE): 10M/100M self-adaptive Ethernet interface
2
INITIAL SET: Reset all parameters to factory default settings.
3
AUDIO OUT: Audio output interface
4
MIC IN: Audio input interface
5
D+, D-: RS-485 interface
6
1A 1B, 2A 2B: Alarm output interface
7
IN1 GND, IN2 GND: Alarm input interface
8
Power supply
9
SD card slot
10
Video output interface
11
Power LED indicator, which turns red when power is applied to the unit
NOTE:
When the camera is power up, press the “INITIAL SET” button for about 10 seconds, then all parameters,
including user name, password, IP address, port number, etc., will be reset to the factory default settings.
2
Quick Guide of Network Dome Camera
2.Installation
The steps of installing the camera on the ceiling as following:
1. Use the screws to fix the bottom plate on the ceiling, and rotate dome camera in anti-clockwise direction to
attach it to the bottom plate, and finally use the lock screw to secure the dome camera into position.
2. Loosen the set screws with a hexagonal screw driver (attached with the camera), and take down the dome
cover .
3
Quick Guide of Network Dome Camera
3. While viewing the video on the monitor, adjust the camera’s view angle for your need.
4. Install the dome cover and tighten the screws.
4
Quick Guide of Network Dome Camera
3. Search and Modify IP
SADP (Search Active Devices Protocol) software can automatically search the IP address of network cameras’ on
the same network with connection diagram as follows:
rk
two
Ne
le
cab
Switch
Net
w
ork
cab
le
Computer
Network Camera
The operation of searching and modifying IP address is described as following:
1. install the SADP software, and then run the
“sadpdlg.exe”.
2. Search IP address.
Click it
3. Modify IP address.
Show the IP address of the camera
5
Quick Guide of Network Dome Camera
1. Click [modify]
2. Input new IP address and the
password ( Default: 12345) of
the camera, then click [save]
3. Modify successfully
6
Quick Guide of Network Dome Camera
4.Preview via IE browser
Note:
The default IP of network cameras’ is ‘192.0.0.64’ with ‘admin’ as the administrator, ‘12345’ as the password,
and ‘8000’ as the default port.
For monitoring camera images, a comptuer running the Microsoft Windows Operating System and Internet
Explorer (Version 6.0 or later) are required. In this manual, we take Windows XP and IE 6.0 for example.
This chapter describes how to view the video from the camera via web browser, and operate as following:
1. Open the IE browser, set the security level to [Medium] in [Tools/InternetOptions/Security/Custom Level…],
and then enable or prompt Activex Control and Plug-in directly as well.
7
Quick Guide of Network Dome Camera
2. Type the IP address of the camera and press [Enter], and then click the mention box that pop up.
3. Click [Run] to install the ActiveX control.
8
Quick Guide of Network Dome Camera
4. Input “Username” (Default: admin), “Password” (Default: 12345) and “Port” (Default: 8000) of the camera,
and then click [Login]
9
Quick Guide of Network Dome Camera
5. View the image
For detailed instructions of further configuration, please refer to the user manual of network camera.
10
Quick Guide of Network Dome Camera
First Choice for Security Professionals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement