DigiLED DMX CA_GB.vp - Vossloh

DigiLED DMX CA_GB.vp - Vossloh
DigiLED DMX CA
WU-ST-003-DigiLED-DMX CA (Ref. No.: 186153)
Introduction
2
Description of Functions
Operation Manual DigiLED DMX CA GB 1/5 March, 2009
2.1 Functional Characteristics
The software integrated in a DigiLED DMX CA unit uses DMX
signals to generate the four PWM control signals (RGBW)
needed for colour control of LED modules in a 24 V CA system.
The four PWM control signals are assigned in accordance with
the DMX address to which the DigiLED DMX CA unit was set
(see 2.2.1).
The set DMX address is recognised and stored as soon as the
unit is connected to the supply voltage. Any changes made to
the DMX address will only be recognised and stored if the
DigiLED DMX CA unit is disconnected from the supply voltage
for a minimum of 5 seconds before being reconnected.
Technical Specifications:
• 1 x DMX input to connect DMX-compatible control units;
polarity must be observed
• 1 x active DMX output for transferring and amplifying the
DMX signal; polarity must be observed
• 4 x PWM outputs (RGBW)
• Control signal range: 0 % ...100 %
• All channels are protected against short-circuiting and overload: in the event of short-circuiting, the channel will make
five attempts to restart. Should these remain unsuccessful,
the respective channel will shut down. Once the problem
has been eliminated, the channel must be restarted (24 V
supply)
• Overheating protection: should the tc temperature be
exceeded, the output circuit will automatically shut down.
Once the problem has been eliminated (i.e. the device
has cooled down again sufficiently), the unit will restart
automatically
• A BUS termination resistor can be activated (see 2.2.2)
2.2 Settings
0
DMX-Adress
1
1xx
Digital LED
Controller
EN 61347-1
EN 61347-2-11
EN 61347-2-13
EN 62384
EN 55015
2
x1x
3
xx1 Ref.-No. 186153
Type WU-ST-003DigiLED-DMX CA
DMX
Output Input
1.1 Product Description
DigiLED DMX CA units are designed to enable individual colour
control of LED modules in 24 V CA assembly systems. The
digital interface was designed in compliance with the DMX512
standard (DIN 56930-2) and is therefore suitable for connection to DMX512 control units.
The DMX transfer protocol (digital multiplex for 512 channels) is
used for controlling DigiLED DMX CA units. This standard was
defined by the United States Institute for Theatre Technology
(USITT). As a system control device, DigiLED DMX CA serves to
control the brightness of high- and/or low-power LED modules
that are of common anode design. Please refer to the
publication entitled "USITT: DMX512/1990 Digital Data
Transmission Standard for Dimmers and Controllers" for the full
wording of the DMX512 standard.
Made in EU
4
Off S1 : off = 8 bit / on = 10 bit
On S2 : off = RGB / on = Mono
S4 S3 S2 S1
S3 : off = 122Hz/on = 976Hz
S4 : not connected
LED - Modules
1
A New Lighting Experience
+
GND
+
GND
Supply Voltage +
Com. +
Red
Green
Blue
White
Ground
-
2.2.1 Using the Decimal Switch to set DMX Addresses
Any address between 001 and 509 can serve as the basic
setting, i.e. as the start address that will be activated every
time the device is switched on. Please note that setting a start
address will also occupy the next three addresses.
For instance, if the start address is 111, then 112 to 114 will
also be assigned. Decimal switches (1) to (3) are used to set
an address, whereby (1) is for the hundred position, (2) is for
the decimal point and (3) is for the unit position.
Using "000" as a start address will automatically activate the
manufacturer's factory settings and result in an orange shade
in RGB modules. Similarly, setting an address higher than
509 will also activate the manufacturer's factory settings.
2.2.2 DMX-BUS Termination
A resistor termination must be fitted to the final receiver of
each DMX512 transmission line. DigiLED DMX CA units are
pre-equipped with such a resistor, which can be activated or
deactivated using a sliding switch (0). The switch is in the
"OFF" position in the diagram shown above.
2.2.3 DIP Switch Assignment
The following operating parameters of a DigiLED DMX CA
unit can be set using the DIP switch (4):
S1: Switch from 8- to 10-bit resolution; the 10-bit mode
logarithmically improves the scaling accuracy of the
dimmer, which permits more precise control when light
intensity is low.
S2: Switch from RGB(W) to mono operation, which switches
all four output channels to behave in an identical manner
to channel 1.
S3: Switch the PWM frequency of 122 Hz to 976 Hz:
The high frequency is particularly suitable for applications in recording studio environments (e.g. film or TV).
S4: Not assigned
Vossloh-Schwabe Deutschland GmbH
Hohe Steinert 8 · 58509 Lüdenscheid, Germany · Phone: +49/23 51/101- 0 · Fax: +49/23 51/101- 217 + - 384 · www.vossloh-schwabe.com
DigiLED DMX CA
WU-ST-003-DigiLED-DMX CA (Ref. No.: 186153)
Technical Data
74
23 to 25 V DC
max. 5 A (see table 4.2)
T5 A 250 V, safety fuse
8-pole push-in terminal for supply voltage
and LED assembly modules in 24 V CA system
(see table 4.2)
6-pole push-in terminal for the DMX512 interface
–20 °C to +45 °C
max. 60 °C
IP20
Plastic, PC white
95 x 60 x 30 mm
75 g
tc=60°C
83.5
93
29
4
4.5
50
10
Ambient temperature
tc point
Degree of protection
Casing
Dimensions (LxWxH)
Weight
4.5
58
Operating Voltage
Current consumption
Fuse protection
Connection
48.5
3
Terminal Connections
0
DMX-Adress
2
x1x
EN 61347-1
EN 61347-2-11
EN 61347-2-13
EN 62384
EN 55015
Type WU-ST-003DigiLED-DMX CA
xx1 Ref.-No. 186153
Made in EU
3
4
Off S1 : off = 8 bit / on = 10 bit
On S2 : off = RGB / on = Mono
S4 S3 S2 S1
S3 : off = 122Hz/on = 976Hz
S4 : not connected
LED - Modules
Digital LED
Controller
DMX
Output Input
1xx
1
+
Input DMX
GND
+
Output DMX
GND
24 V DC
Supply Voltage +
Com. +
Red
Green
Blue
White
Ground
+ module
red
green
blue
white
– module
-
4.1 DMX Terminal
Terminal
Input DMX +
•
Function
+ Connection for DMX signal (input)
Recommended Lead
BUS line with an impedance value
Input DMX –
– Connection for DMX signal (input)
of 120 Ohm
Input GND
Ground (possibly for shielding the DMX line)
•
•
•
•
•
Output DMX +
+ Connection for DMX signal (output)
Output DMX –
– Connection for DMX signal (output)
Output GND
Ground (possibly for shielding the DMX line)
Product
DMX unit
4.2 Terminal Block 24 V and Module Connection
Pole
Colour Coding
1
•
•
•
•
•
•
•
•
2
3
Operation Manual DigiLED DMX CA GB 2/5 March, 2009
4
5
6
7
8
Recommended Lead
Connection
Black
Max. Current
Function
Carrying Capacity
5A
Supply line for optional 24 V converter (GND)
Standard two-strand supply lead
24 V DC converter
Red
5A
Supply line for optional 24 V converter (+24 V)
(0.5 –1.5 mm2)
Red
5A
Supply line for LED assembly modules (+24 V)
High Power feed in cable
LED assembly modules
Orange
1.25 A
PWM signal line for channel 1/Red
(Ref. No. 535900)
or module group for
Green
1.25 A
PWM signal line for channel 2/Green
or
24 V CA system
Blue
1.25 A
PWM signal line for channel 3/Blue
Standard six-strand lead
or
(e.g.: LIYY 6X0.75 mm²)
PCB distributor or slave
Grey
1.25 A
PWM signal line for channel 4/White
Black
5A
Supply line for LED assembly modules (GND)
board for 24 V CA system
Vossloh-Schwabe Deutschland GmbH
Hohe Steinert 8 · 58509 Lüdenscheid, Germany · Phone: +49/23 51/101- 0 · Fax: +49/23 51/101- 217 + - 384 · www.vossloh-schwabe.com
DigiLED DMX CA
WU-ST-003-DigiLED-DMX CA (Ref. No.: 186153)
5
DigiLED DMX CA Connections
5.1 Input and DMX Terminal
• DMX: Connect DigiLED DMX CA to the DMX control unit
using the DMX terminal. Further DMX units can be cascaded
(up to a maximum of 32 devices) by creating an active
output (DMX output). In so doing, the DMX signal can be
connected through from DigiLED to DigiLED unit.
• Voltage supply: DigiLED DMX CA is supplied with 24 V DC
via terminals 1 and 2 (see table 4.2).
5.2 Output
5.2.1 Connection of HighPower 24 V RGB(W)
LED Assembly Modules
a) The feed in cable (Ref. No. 535900) must be used to
connect a HighPower 24 V RGB(W) LED assembly
module. For direct connection, use terminals 3 to 8 of
DigiLED DMX CA. Correct polarity (colour coding) must
be ensured in accordance with table 4.2.
DigiLED Colour control
DigiLED Manual CA
(Ref. No.: 186136)
DigiLED DALI CA
(Ref. No.: 186138)
DigiLED Push CA
(Ref. No.: 186144)
DigiLED DMX CA
(Ref. No.: 186153)
24V +
+
R
G
B
W
-
High Power Feed in
Ref. No. 535900
(Layout of connection terminals depend
on colour control unit)
Converter LEDLine EDX
RGB Flood
LEDLine EDXe 110 (Ref. No.: 186055)
LEDLine EDXe 120 (Ref. No.: 186129)
b) To connect several HighPower 24 V RGB(W) LED assembly
modules, the PCB distributor (Ref. No. 186141) must be
connected to DigiLED DMX CA using a standard six-strand
lead (e.g. LIYY 6X0.75 mm²).
Correct polarity (colour coding) must be ensured in accordance with table 4.2. LED assembly modules are connected
to the distributor using flatband cables (Ref. No. 535898 or
535899).
LEDLine EDXe 170
(Ref. No.: 186103 – Built-in)
(Ref. No.: 186104 – Independent)
(Ref. No.: 186105 – IP67)
24 V DC
230 V ~
LEDLine EDXe 130 (Ref. No.: 186058)
LEDLine EDXe 1130
(Ref. No.: 186131 – Built-in)
(Ref. No.: 186132 – Independent)
(Ref. No.: 186133 – IP67)
DigiLED Colour control
PCB Distributor
High Power Distributor
Ref. No. 186141
DigiLED Manual CA
(Ref. No.: 186136)
RGB Triple
DigiLED DALI CA
(Ref. No.: 186138)
DigiLED Push CA
(Ref. No.: 186144)
DigiLED DMX CA
(Ref. No.: 186153)
24V +
+
R
G
B
W
-
W
B
G
R
+
(Layout of connection terminals depend
on colour control unit)
Converter LEDLine EDX
RGB Line
RGB Flood
LEDLine EDXe 110 (Ref. No.: 186055)
LEDLine EDXe 120 (Ref. No.: 186129)
LEDLine EDXe 170
(Ref. No.: 186103 – Built-in)
(Ref. No.: 186104 – Independent)
(Ref. No.: 186105 – IP67)
24 V DC
230 V ~
LEDLine EDXe 130 (Ref. No.: 186058)
Commercially available
e.g. LIYY
LEDLine EDXe 1130
Operation Manual DigiLED DMX CA GB 3/5 March, 2009
(Ref. No.: 186131 – Built-in)
(Ref. No.: 186132 – Independent)
(Ref. No.: 186133 – IP67)
High Power PCB-PCB-connector
Ref. No. 535898 (20 mm)
Ref. No. 535899 (100 mm)
The maximum number of connected LED assembly modules is
limited by the power rating of the converter and by the max.
current load of the outputs in accordance to table 4.2.
The power and current draw values of the connected LED
assembly modules as well as connection cable and PCB
distributor data can be found in the respective data sheets at
www.vs-optoelectronic.com.
The maximum power rating for a DigiLED DMX CA unit totals
120 W.
Vossloh-Schwabe Deutschland GmbH
Hohe Steinert 8 · 58509 Lüdenscheid, Germany · Phone: +49/23 51/101- 0 · Fax: +49/23 51/101- 217 + - 384 · www.vossloh-schwabe.com
DigiLED DMX CA
WU-ST-003-DigiLED-DMX CA (Ref. No.: 186153)
c) System performance can be extended beyond 120 W using
slave boards to feed in additional power.
Functional descriptions and terminal connections for slave
boards can be found in the respective data sheets at
www.vs-optoelectronic.com.
Voltage Supply by first Converter
Converter LEDLine EDX
High Power Distributor
Ref. No. 186141
LEDLine EDXe 110 (Ref. No.: 186055)
RGB Triple
LEDLine EDXe 120 (Ref. No.: 186129)
LEDLine EDXe 170
W
B
G
R
+
24 V DC
230 V ~
LEDLine EDXe 130 (Ref. No.: 186058)
(Ref. No.: 186103 – Built-in)
(Ref. No.: 186104 – Independent)
(Ref. No.: 186105 – IP67)
LEDLine EDXe 1130
(Ref. No.: 186131 – Built-in)
(Ref. No.: 186132 – Independent)
(Ref. No.: 186133 – IP67)
RGB Line
DigiLED colour control
RGB Flood
High Power
Slave PCB
Ref. No. 186140
DigiLED Manual CA
(Ref. No.: 186136)
DigiLED DALI CA
(Ref. No.: 186138)
DigiLED Push CA
(Ref. No.: 186144)
DigiLED DMX CA
(Ref. No.: 186153)
24V +
+
R
G
B
W
-
Slave 1
Slave 2
System Expansion by
High Power Slave PCB and
additional Converter
High Power Distributor
Ref. No. 186141
RGB Triple
W
B
G
R
+
Converter LEDLine EDX
LEDLine EDXe 110 (Ref. No.: 186055)
LEDLine EDXe 120 (Ref. No.: 186129)
24 V DC
230 V ~
LEDLine EDXe 130 (Ref. No.: 186058)
LEDLine EDXe 170
(Ref. No.: 186103 – Built-in)
(Ref. No.: 186104 – Independent)
(Ref. No.: 186105 – IP67)
RGB Line
RGB Flood
Commercially available control cable e.g. LIYY
LEDLine EDXe 1130
High Power PCB-PCB-connector
Ref. No. 535898 (20 mm)
Ref. No. 535899 (100 mm)
(Ref. No.: 186131 – Built-in)
(Ref. No.: 186132 – Independent)
(Ref. No.: 186133 – IP67)
5.2.2 Connection of LowPower 24 V
Assembly Modules
LowPower 24 V RGB CA LED assembly modules with four
connection elements (+RGB) can be directly connected to
DigiLED DMX CA via poles 3 (+), 4 (red channel), 5
(green channel) and 6 (blue channel) under observation of
the permissible power rating. Compliance with the colour
coding (polarity) detailed in table 4.2 must be ensured.
DigiLED colour control
DigiLED Manual CA
(Ref. No.: 186136)
The maximum number of connected LowPower LED assembly
modules is limited by the power rating of the connected
converter and the maximum current load of pole 4, 5 and 6
(sum: 90 W) in accordance with table 4.2. The power and
current draw values of the connected LED assembly modules
can be found at www.vs-optoelectronic.com.
The maximum power rating with which a DigiLED DMX CA unit
can be operated totals 90 W. System performance can be
extended by connecting further DigiLED DMX CA units.
DigiLED DALI CA
(Ref. No.: 186138)
DigiLED Push CA
(Ref. No.: 186144)
DigiLED DMX CA
(Ref. No. 186153)
24V +
+
R
G
B
W
-
tc
LEDLine Flex SMD RGB CA
(Layout of connection terminals depend
on colour control unit)
Converter LEDLine EDX
LEDLine EDXe 120 (Ref. No.: 186129)
LEDLine EDXe 170
(Ref. No.: 186103 – Built-in)
(Ref. No.: 186104 – Independent)
(Ref. No.: 186105 – IP67)
24 V DC
LEDLine EDXe 130 (Ref. No.: 186058)
230 V ~
Operation Manual DigiLED DMX CA GB 4/5 March, 2009
LEDLine EDXe 110 (Ref. No.: 186055)
LEDLine EDXe 1130
(Ref. No.: 186131 – Built-in)
(Ref. No.: 186132 – Independent)
(Ref. No.: 186133 – IP67)
Vossloh-Schwabe Deutschland GmbH
Hohe Steinert 8 · 58509 Lüdenscheid, Germany · Phone: +49/23 51/101- 0 · Fax: +49/23 51/101- 217 + - 384 · www.vossloh-schwabe.com
DigiLED DMX CA
WU-ST-003-DigiLED-DMX CA (Ref. No.: 186153)
6
Notes on Installation and Safe Operation
6.1 Installation
Installation must be carried out under observation of the relevant
regulations and standards. The components of the 24 V CA
system are designed for operation within a casing or luminaire.
Installation must be carried out in a voltage-free state (i.e.
disconnection from the mains). The following advice must be
observed; non-observance can result in the destruction of the
components, fire and/or other hazards:
• DigiLED DMX CA is exclusively designed for operating 24 V
Common Anode LED modules.
• The load range of the connected 24 V converter must be
observed.
• The maximum output currents specified in table 4.2 must not
be exceeded.
• The temperature measured at the tc point must not exceed the
specified limit (tcmax. = 60°C) during operation.
Operation Manual DigiLED DMX CA GB 5/5 March, 2009
6.2 Assembly
• Installation any way up
• Installation only in dry rooms or luminaires, box casings or
similar. If DigiLED DMX CA is to be installed outdoors or in
a damp location, a casing of a suitable protection class (IP)
must be used.
• Attach using 4 mm screws
• Ensure solid and even surface for unit to rest on
7
Standards
7.1 Applied Standards
EN 61347–1
Lamp controlgear – Part 1: General requirements and tests
(IEC 61347–1:2000);
German Version EN 61347–1:2001
EN 61347–2–11
Lamp controlgear – Part 2–11: Particular requirements
for miscellaneous electronic circuits used with luminaires
(IEC 61347–2–11:2001);
German Version EN 61347–2–11:2001
EN 55015
Limits and methods of measurement of radio disturbance
characteristics of electrical lighting and similar equipment
7.2 Standards to adhere
EN 61347–2–13
Lamp controlgear – Part 2–13: Particular requirements for
D.C. or A.C. supplied electronic controlgear for LED modules
EN 62384
D.C. or A.C. supplied electronic control gear for LED modules –
Performance requirements
Vossloh-Schwabe Deutschland GmbH
Hohe Steinert 8 · 58509 Lüdenscheid, Germany · Phone: +49/23 51/101- 0 · Fax: +49/23 51/101- 217 + - 384 · www.vossloh-schwabe.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement