X-Power-HP-Pro - Acclaim Lighting

X-Power-HP-Pro - Acclaim Lighting
7.Appendix: System Connection Diagram
EXAMPLE 1: Detail wiring diagram for High Power LED Bar system
6
90-240VAC,
50/60Hz.
2 1
1
X-Power-HP-Pro
DMX IN
X-Power-HP-Pro
DMX OUT
6
90-240VAC,
50/60Hz.
2 1
1
X-Power-HP-Pro
DMX IN
DMX OUT
2
X- P O W E R- H P- P R O
Acclaim Lighting - Los Angeles, CA 90040
90-240VAC,
50/60Hz.
www.acclaimlighting.com
6
(Dip Switches 10 = on)
SWITCHES ON
(Dip Switches 10 = off)
1 2 3 4 5 6 7 8 9 10
START
CH#
SWITCHES ON
1,2,4
ON
11
12
3,4
13
1,3,4
000
3
1,3
14
2,3,4
100
15
1,2,3,4
010
511
3
2
1
4
5
6
6
2,3
7
1,2,3
8
9
4
1,4
10
2,4
ON
1 2 3
0.1S
000
1
100
0.2S
100
2
010
0.5S
010
3
110
4
011
1,2,3,4,5,6,7,8,9
111
100%
001
101
110
3
Green +
White +
White +
Green +
4
Green White White Green -
1S
110
001
5S
001
5
101
10S
101
6
011
20S
011
111
30S
111
OUTPUT
1
2
Red White Warm White Red -
5
Blue +
White +
Warm White +
Blue +
2
3
4
5
1 =ON
6
6
Blue White Warm White Blue -
1 =ON
4 5
0=OFF
00
10
01
11
RGB
White
White & Warm
RGB
7
AUTO
MODE
1 Group
2 Group
3 Group
6 Group
2
6
P/N: 24-004-2625-00
Draft copy (Rev1.0)
6
WWW.Acclaimlighting.com
-9-
1 2
0=OFF
00
10
01
11
Instruction Manual
High Power LED Bar(Sold Separately)
78 9
000
OUTPUT TERMINALS
1
Red +
White +
Warm White +
Red +
ON
4 5 6
0%
.. .. .. .. .. ..
1
2
1,2
PROGRAM
.. .. .. ..
1
2
1 2 3 4 5 6 7 8 9 10
SPEED
FADE TIME
RS
ON
STAND ALONE
.. .. .. ..
START
CH#
2 1
X-Power-HP-Pro
DMX IN
0 = OFF 1 = ON
RS
ON
DMX ADDRESS (SLAVE)
6.Technical Specifications
Power Input:
AC110-120V(3.2A)/AC220-240V(1.6A), 50/60Hz
DMX In:
3-pin male XLR connector or terminal
DMX Out:
3-pin female XLR connector or terminal
Output:
6 output terminals, 3x350mA per output
Dimension:
285X176X67mm
Weight:
2.2kg
*Please Note:
Specifications and improvements in the design of this unit and this manual are subject to change without any
prior written notice.
Physical Dimensions
Back View
Front View
Top View
X-Power-HP-Pro
-8-
5.2.6 Manual Dim Mode
In Manual Dim Mode, it allows to manually control overall output intensity.
Flip the dip-switch 6 of the 6-way Mode Dip Switch to the "ON" position and the Manual Dim Mode is
engaged. In this function, the dip-switch1~8 of the 10-way Function Dip Switch is used to set overall output
intensity. Each dip-switch represents a binary value.
Dip Switch 1 intensity equals 1
Dip Switch 2 intensity equals 2
Dip Switch 3 intensity equals 4
Dip Switch 4 intensity equals 8
Dip Switch 5 intensity equals 16
Dip Switch 6 intensity equals 32
Dip Switch 7 intensity equals 64
Dip Switch 8 intensity equals 128
1
2
3
4
5
6
7
8
9
10
SWITCHES ON
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
3
4
5
6
7
Intensity
value
11
12
13
14
15
8
9 10
SWITCHES ON
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
.. .. .. ..
Intensity
value
2
.. .. .. ..
1
1. General information...................................................................................1
RS
ON
Table of Contents
255
1,2,3,4,5,6,7,8
The intensity can be set by combining the different dipswitches that will add up to the value you wish to
achieve, for example:
Setting the intensity for 21.
Setting the intensity for 201.
Example 1:
Example 2:
Flip switches1,3,&5 to the
Flip switches1,4,7,& 8 to the
"ON" position
"ON" position
1=1
1=1
3=4
4=8
Dipswitches# 5=16 Value
Dipswitches# 7=64 Value
=21
8=128
=201
1.1.Unpacking...................................................................................1
1.2.Safety warnings...........................................................................1
2. Main features..............................................................................................2
3. Setup.......................................................................................................2&3
4. Product layout & functions....................................................................3&4
4.1.Front panel layout.......................................................................3
4.2.Rear panel layout........................................................................4
5. Operation guide...................................................................................4,5,6
5.1.DMX control mode....................................................................4
5.2.Stand alone mode......................................................................4
5.2.1.Setting fade time..........................................................................4
5.2.2.Adjusting chase speed.................................................................5
5.2.3.Selecting built-in programs..........................................................5
5.2.4.Output group modes...................................................................6
5.2.5.Output loading modes.................................................................6
5.2.6.Manual Dim Mode.......................................................................7
6. Technical specifications...............................................................................8
7. Appendix: System connection diagram.....................................................9
-7-
1.General Information
5.2.4 Output Group Mode Setting
1.1 Unpacking
In the function, the dip-switch 1& 2 (6-way Mode Dip Switch)is used to set your desired Output Group mode.
Every X-Power-HP-Pro has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping. If the carton
appears to be damaged, carefully inspect your controller for any damage and be sure all equipment
necessary to operate the unit has arrived intact. In case damage has been found or parts are missing, please
contact us or your nearest dealer/distributor for further instructions.
1.) 1 Group Output Mode is engaged by flipping the dip-switch 1& 2 to the "OFF"
position, has 1 group output and Output 1~6 is identical.
1 2
2.) 2 Group Output Mode is engaged by flipping the dip-switch 1 to the "ON"
position and the dip-switch 2 to the "OFF" position, has 2 group output and has
0=OFF
3 identical outputs distributed over 2 groups, Output1~3 is identical, and Output
00
1 Group
4~6 is identical.
10
2 Group
3.) 3 Group Output Mode is engaged by flipping the dip-switch 1 to the "OFF"
01
3 Group
position and the dip-switch 2 to the "ON" position, has 3 group output and has
11
6 Group
2 identical outputs distributed over 3 groups, Output1~2 is identical, Output 3~4
is identical and Output 5~6 is identical.
4.) 6 Group Output Mode is engaged by flipping the dip-switch 1& 2 to the "ON" position, has 6 group output
and Output 1~6 is not perfectly identical.
To optimize performance of this product, please read instructions in this manual and on the case of this
product carefully to familiarize yourself with the basic operations. Once manual has been thoroughly read,
we recommend you should file it for future reference.
You should be in possession of the following items:
1 X-Power-HP-Pro
1 Instruction Manual
1 Screwdriver
MODE
1 =ON
5.2.5 Output loading Mode Setting
Caution!
There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void
your manufactures warranty. In the unlikely event your unit may require service, please contact Acclaimlighting
customer support.
In the function, user can flip the dip-switch 5 & 6(6-way Mode Dip Switch) to sel the desired Output Loading
Mode.
OUTPUT
1 =ON
Do not discard the packing carton in the trash. Please recycle when ever possible.
The socket-outlet shall be installed near the equipment and shall not be easily accessible
Le socle de prise de courant doit être installé à proximité du matériel et doit être
aisément accessible.
1.2 Safety Warnings
The ground connection should be essential for this unit.
Do not make any inflammable liquids, water or metal objects enter the unit.
To prevent or reduce the risk of electric shock, DO NOT OPEN THE TOP COVER.
This unit must be operated by adults, do not allow children to play with it.
There are no user serviceable parts inside this unit. Do not attempt any repairs yourself.
Should you experience any problem during use, please contact your local dealer immediately.
Do not discard the shipping carton in the trash. Please recycle when ever possible.
Always consult authorized personnel for any repairs and maintenance.
When unpacking, please check the unit is not damaged. Should something wrong happen to this product,
contact the local dealer immediately.
All rights reserved. No part of the manual included with this product may be reproduced, transmitted,
transcribed or translated into any language in any form, by any means, without authorized permission.
-1-
OUTPUT TERMINALS
4 5
1
2
3
4
5
6
0=OFF
00
10
01
11
RGB
WHITE
WHITE&WARM
RGB
1
Red+
White +
Warm White +
Blue +
2
Red White Warm White Blue -
3
Green +
White +
White +
Red +
4
GreenWhite White Red +
6
5
Blue Blue +
White White +
Warm White + Warm White Green Green +
1.) RGB Output Mode is engaged by flipping the dip-switch 4 and 5 to the "OFF" position, one output with
R.G.B. Control is controlled by three channels separately.
2.) WHITE Output Mode is engaged by flipping the dip-switch 4 to the "ON" position and the dip-switch 5 to
the "OFF" position, one output with R.G.B. Control is controlled by one channel and the output of R.G.B. Is
identical.
3.) COOL WHITE & WARM WHITE Output Mode is engaged by flipping the dip-switch 4 to the "OFF" position
and the dip-switch 5 to the "ON" position, one output with Cool White & Warm White is controlled by two
channels. The output with Cool White is controlled by Ch 1, and the output of R.B. Is identical; the output
with Warm White is controlled by Ch 2, and the output is G.
4.) RGB Output Mode is engaged by flipping the dip-switch 4 and 5 to the "ON" position, one output with
R.G.B. Control is controlled by three channels separately.
-6-
5.2.1 Setting fade time
2.Main Features
1. The Stand Alone Mode enables.
2. Thus, flip the dip-switch 1,2 & 3(10-way Function Dip Switch) to set a desired level for fade time.
ON
1 2 3
000
100
010
110
001
101
011
111
FADE TIME
(Dip Switches 10 = off)
"0" = "OFF" position
"1" = "ON" position.
5.2.2 Adjusting chase speed
0%
14%
28%
43%
57%
71%
86%
100%
1. The Stand Alone Mode enables;
2. Thus, flip the dip-switch 4,5 & 6(10-way Function Dip Switch)to adjust a desired level for chasing speed.
ON
X-Power-HP-Pro is a HP LED control unit, specially used to drive 1 Watt high power LED
fixtures, such as High Power LED Bar.
High frequency driving HP LED bars suitable for CCD cameras pick up facility.
X-Power-HP-Pro is engaged as a combination of a control interface and tension provider
for 1Watt high power LED fixtures.
Ability of the maximum of 6 channels can be controlled separately, allows a maximum loads of 3x350mA
per output and the maximum amount connected loads distributed over all 6 outputs must not exceed 6A.
All work modes and parameters can be set by flipping 10-way Function Dip Switch and 6-way Mode Dip
Switch.
USITT DMX512(1990) multiplexed digital control, via 3 pin XLR connector or terminals.
DMX Control Mode and Stand Alone Mode available .
1~7 patterns plus a sequence of 7 patterns, chase speed & fade time adjustable..
Different Output Group modes for user assignable.
Output loading modes available in R.G.B mode, WHITE mode and COOL WHITE& WARM WHITE mode.
Manual Dim mode allows to control overall output intensity.
Full range voltage of AC 110-120V/AC220-240V power input option by voltage selector.
Providing built-in DC24V 6.5A PSU.
Power Failure Memory.
3.Set Up
4 5 6
3.1 Power Supply:
SPEED
(Dip Switches 10 = off)
"0" = "OFF" position
"1" = "ON" position.
000
100
010
110
001
101
011
111
Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your
X-Power-HP-Pro power supply. The X-Power-HP-Pro is available in a 120V and 230V version. Due to variations
in line voltage from venue to venue, be sure to plug your power supply into a wall outlet with matching
power before attempting to operate.
0.1S
0.2S
0.5S
1S
5S
10S
20S
30S
3.2 Data Cable (DMX Cable) Requirements:
Connect the High Power DMX Controller TV and your fixtures together using standard 3 pin DMX cables. The
High Power DMX Controller TV uses DMX-512 protocol to operate your fixtures.
5.2.3 Selecting Built-in programs
1. The Stand Alone mode enables;
2. Thus, flip the dip-switch 7,8 & 9 (10-way Function Dip Switch) TO select the desired program.
ON
PROGRAM
(Dip Switches 10 = off)
"0" = "OFF" position
"1" = "ON" position.
AUTO=a sequence of 7 programs
-5-
Notice:
78 9
000
100
010
110
001
101
011
111
If you are constructing your own data cables, be sure to use standard two conductor
shielded cable (This cable may be purchased at almost all professional sound and
lighting stores). Your cables should be made with a 3-pin male and female XLR
connector on either end of the cable. Also remember that DMX lines must be daisy
chained and can not be split.
1
2
3
4
5
6
7
AUTO
Figure 1
Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR
connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to
come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and erratic
behavior.
XLR Male Socket
1 Ground
XLR Female Socket
2 Cold
2 Cold
XLR Pin Configuration
1 Ground
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
DMX 512 OUT
3-PIN XLR
1
1
3
3
2
Figure 2
Pin 3 = Data True (positive)
3 Hot
3 Hot
2
DMX 512 IN
3-PIN XLR
Figure 3
Special Note:
Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behavior. A terminator is a 120 ohm 1/4 watt resistor which is connected between pins 2 and 3
of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator will decrease the possibilities of
erratic behavior.
-2-
Termination reduces signal errors and avoids signal transmission
problems and interference. It is always advisable to connect a
DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (
DMX-) and PIN 3 (DMX +) of the last fixture.
1
3
2
4.2 Rear Panel Layout
Figure 4
1
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin
line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
1. Power Input: AC110~120V(3.2A)/AC220-240V(1.6A), 50~60Hz.
2. Voltage Selector:AC120V/230V optional by this voltage selector.
3-Pin XLR to 5-Pin XLR Conversion
Data Compliment(-signal)
Data True(+signal)
5-pin XLR Male(In)
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Used
Not Used
Pin 5 - Do Not Used
5.Operation Guide
5.1 DMX Control Mode(DMX Addressing)
DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication
between intelligent fixtures. Each dip switch represents a binary value.
4.Product Layout & Functions
4.1 Front Panel Layout
OUTPUT: 3x350mA per output
1 2 3
DMX Address Setting
5
1
2
4
8
16
32
64
128
256
4
DMX OUT
18 LEDs With 6 Ports (1), (2), (3), (4), (5), (6);
36 LEDs With 3 Ports (1, 2), (3, 4), (5, 6).
3
1
1 2 3 4 5 6 7 8 9 10
OUTPUT
Manual DIM
MODE
3
NC
1 2 3 4 5 6
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
DMX ADDRESS (SLAVE)
START
CH#
SWITCHES ON
1
2
3
4
5
6
7
8
9
10
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
RS
ON
(Dip Switch 10 = on)
1 2 3 4 5 6 7 8 9 10
START
CH#
SWITCHES ON
11
12
13
14
15
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
.. .. .. ..
3-Pin XLR Female(Out)
.. .. .. ..
Conductor
Ground/Shield
2
511
1,2,3,4,5,6,7,8,9
ON
1=Ground; 2=Data - ; 3=Data+
OFF
2
1
2
3
4
5
6
4
1
2
3
4
5
6
6
1
2
3
4
5
STAND ALONE
MANUAL
( Dipswitch 10 = OFF )
( Dipswitch 6
= ON )
#1 - 3 Fade time
#4 - 6 Speed
#7 - 9 Program
6
#1 - 8
Level 0-255
1 2 3
2
DMX IN
1
1. Dip Switches(10-way and 6-way):
Flip 10-way and 6-way Dip Switches to set some functions and modes for user's desired effects.
2. DMX Input:
3-Pin XLR male connector or terminal. Connect a universal DMX controller into this input for receiving DMX
values or DMX signals.
3. DMX Output:
3-Pin XLR female connector or terminal. Connect to next DMX fixtures for sending DMX values or DMX
signals.
4. Output:
6 terminal output connectors, allows a maximum loads of 3x350mA per output and the maximum amount
connected loads distributed over all 6 outputs must not exceed 6A.
In this mode, the dip-switch 10 is flipped to the "ON" position. And this switch sometimes used to activate
some fixture special functions.
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to
achieve, for example:
5.2Stand Alone Mode
The Stand Alone Mode is engaged in by flipping the dip-switch 10 to the "OFF" position. And this mode includes
sub-modes with many functions, such as fade time, chasing speed, built-in programs.
ON
OFF
-3-
Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
1=1
4=8
Dipswitches#
7=64 Value
8=128
=201
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
1=1
3=4
Dipswitches#
5=16 Value
=21
RS
ON
1 2 3 4 5 6 7 8 9 10
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising