Thermo-dryer New With air temperature adjustment function RoHS Stable supply of temperaturee and pressure controlled dry clean air! Possible to supply compressed Application example Air bearing compressed air air with the same conditions Supplying with constant conditions to and quality regardless of the air bearings mounted on the tool. season. Compressed air Compressed air Air flow capacity (L/min[ANR]) IDH;4 : 100 to 500 IDH;6 : 200 to 800 All-in-One Machine tool Outlet air temperature adjustment range: Temperature control (Heater) Pressure regulation (Regulator) Dehumidification (Dryer) 15 to 30°C (possible to extend depending on the conditions) Outlet air temperature stability: 1 ±0.1°C Outlet air set pressure range: 0.15 to 0.85 MPa Outlet air pressure dew point: 10°C Nominal filtration rating: 0.01 μm Outlet oil mist concentration: Cleaning (Filter) Built-in filter MAX. 0.01 mg/m3 [ANR] specifications 2 (z0.008 ppm) Outlet cleanliness: Particles of 0.3 μm or more: 3.5 particles/L [ANR] or less 1 Performance when the operation of each part is stable without fluctuations in operating conditions and power supply. 2 Performance of the built-in filter, which depends on the inlet air conditions. Power supply available all over the world Model Air flow capacity (L/min [ANR]) IDH;4 100 to 500 IDH;6 200 to 800 Single-phase 100 VAC, 200 VAC, 230 VAC (50/60 Hz) Outlet air temperature Outlet air set Outlet air temperature adjustment range (°C) pressure range (MPa) stability (°C) 15 to 30 Series IDH ; 0.15 to 0.85 ±0.1 Filter nominal filtration rating Temperature control method 0.01 μm (99.9% filtration efficiency) Heater operation PID control Port size Rc3/8 Rc1/2 P-E10-12A Thermo-dryer Compact, Space saving Installation close to a wall is possible. Wall 498 (568) Wall Ve nti lat ion ho le Installation close to a wall is possible with the ventilation holes on the front and top sides. Ventilation hole Ventila tion ho (4 85 ) le 45 5 270 (27 0) For IDHF4 Dimensions in brackets indicate for IDHF6. Unit: mm Convenient Functions Power failure auto-restart function Control temperature failure alarm Even if operation is stopped by unexpected power failure, once the power supply is recovered, the operation will start automatically. If the temperature exceeds the set temperature by an arbitrary amount, an error signal will be generated. If an instantaneous power failure occurs, the operation may restart after a few minutes. At shipment, if the control temperature exceeds or goes under the set temperature by p5ºC, an error signal will be generated. Auto-tuning (A·T) function Key-lock function The control set values (PID) are automatically set. The set value is protected so it will not be changed even if keys are touched by mistake or setting is changed. Regulator handle Large digital display Built-in filter The discharge of drainage and element replacement timing can be checked visually. 3 Filter1(AME) 4 Super Mist Separator · Nominal filtration rating: 0.01 μm (99.9% filtration efficiency) · Outlet oil mist concentration: MAX. 0.01 mg/m3 [ANR] (z0.008 ppm) · Outlet oil mist concentration: Particles of 0.3 μm or more: 3.5 particles/L Pressure adjustment [ANR] or less 1 2 5 6 7 handle Display Function 1 PV Displays the outlet air temperature. 2 SV Displays the outlet air temperature set value. (Default: 25°C) 3 C1 Lights up or flashes when the temperature adjustment heater is operating. 4 AL1 Flashes when a control temperature error is generated. 5 SEL This key is used to change and fix the set value. 6 ? Increases the set temperature and set values. ? Decreases the set temperature and set values. 7 Remote operation, stop, error signal output functions are provided. It is possible to achieve centralized control in a factory with remote operation, stop and error signal output functions. It is possible to synchronize the operation of the dryer with the external air compressor operation to prevent people from forgetting to turn it off and contribute to energy saving. Drain outlet Dustproof filter standard equipment Filter0(AMH) Built-in earth leakage breaker Micro Mist Separator with Pre-filter · Nominal filtration rating: 0.01 μm (99.9% filtration efficiency) · Outlet oil mist concentration: MAX. 0.1 mg/m3 [ANR] (z0.08 ppm) Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 Fax: 03-5298-5362 http://www.smcworld.com © 2011 SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-DN 1st printing PS printing PS 7850SZ Printed in Japan.