iaq50x air measuring station with integral damper and calibrated

iaq50x air measuring station with integral damper and calibrated
®
3900 Dr. Greaves Rd.
•
Kansas City, MO 64030
•
(816) 761-7476
•
IAQ50X AIR MEASURING STATION
WITH INTEGRAL DAMPER AND CALIBRATED CONTROLS
FAX (816) 765-8955
APPLICATION
The IAQ50X is an air measuring station with an ultra low-leak, high
performance control damper that is integral to the flow sensing
section. This patented design provides a solution that measures
and controls flow down to 150 feet per minute in an 11” (279) deep
assembly. The assembly meets AMCA class 1 leakage requirements, so it is perfect for building envelope penetrations. The complete unit is factory assembled and calibrated at multiple points, to
provide effective setpoint monitoring and adjustment. The unit
comes standard with an application specific control panel, actuator
and a honeycomb air flow straightener. Control with a 0-10 VDC
input from the BAS. Provides a 0-10 VDC output that is proportional to the CFM.
STANDARD CONSTRUCTION
FRAME
Nominal 6” x 13/8" (152 x 35) 6063T6 high yield extruded aluminum hat channel with .125” (3.18) wall thickness.
INTEGRAL DAMPER BLADES
Airfoil shaped 6063T6 high yield heavy gauge extruded aluminum.
SENSOR BLADES
Clear Anodized, 6063T6 high yield heavy gauge extruded aluminum.
SENSOR PORT FITTINGS
Brass.
AIR FLOW STRAIGHTENER
1/2" (13) Honeycomb Cell x 3" (76) 3000 series aluminum alloy.
SEALS
Ruskiprene blade edge seals and stainless steel jamb seals.
Leakage meets AMCA Class 1 (3 cfm per sq. ft. at 1" w.g.).
BEARINGS
Molded Lexan.
LINKAGE
Plated steel, concealed in frame.
AXLES
1/2" (13) plated steel hex.
POWER REQUIREMENTS
120 Vac, 50/60 Hz to control panel terminal strip.
ELECTRIC ACTUATOR(S)
MS7510IAQ or MS7520IAQ (as required).
24 Vac, 50/60 Hz, powered by control Panel.
CONTROL PANEL
IAQ020 Digital Controller (reference catalog sheet).
Application specific set points factory calibrated.
Program logic & calibration in nonvolatile EPROM.
RU-275-R2-VDC Pressure Transducer.
IAQ080 120Vac/24Vac power transformer (85VA).
18" x 18" x 6" (457 x 457 x 152) Painted Electrical Enclosure.
MINIMUM SIZE
Single -10”w x 10"h (254 x 254).
Multiple section assembly - unlimited.
MAXIMUM SIZE
Single section - 48”w x 84"h (1219 x 2134).
Multiple section assembly - unlimited.
VELOCITY REQUIREMENTS
Product Range 150 to 2000 FPM (Face Area).
OPERATING TEMPERATURE
-22° F to +140° F (-30°C to 60°C) standard.
Spec IAQ50X-1011/Replaces IAQ50X-308
AIR FLOW
Static Pressure
Measuring Chamber
Total Pressure
Measuring Chamber
IAQ SENSING BLADE DETAIL
FEATURES
• Honeycomb airflow straightener
• Anodized aluminum sensing blades
• Application specific, factory calibrated controller in nonvolatile
EPROM
• 0-10 VDC input
• 0-10 VDC output proportional to CFM
• Flow alarm contacts – LEED EQc1 solution
• Single point 120 volt power connection
Ruskin IAQ50X helps satisfy the requirements for minimum outside air as required by the following.
• ASHRAE 62.1, ASHRAE 90.1 and ASHRAE 189.1.
• California Title 24
• International Mechanical Code (IMC)
• International Energy Conservation Code (IECC)
VARIATIONS
Ruskin model IAQ50X is available with the following variations at
additional cost.
• Stainless steel axle bearings
• Stainless steel linkage (includes axles, tie bars & control arms)
* Flanged connection - front, rear, double or offset
• Internally mounted actuator (external mount is standard)
• Min./Max. units with CD50 for Economizer Operation
Notes:
1. Dimensions shown in ( ) indicate millimeters.
2. Refer to installation manual for additional details.
3. Units furnished approximately 1/4" (6) smaller than given opening dimensions.
4. To order, send completed Order Process Sheet with purchase
order.
ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION.
© Ruskin 2011
DIMENSIONAL DETAILS
A - Width
Honeycomb
Straightener
11”
(279)
Stainless
Compression
Jamb Seal
B - Height
AIR FLOW
Integral Extruded
Damper Blades
Anodized Flow
Sensing Blades
Face View (Internal Actuator Shown)
MOUNTING FLANGE OPTIONS
FRONT FLANGE
5”
(127)
REAR FLANGE
ACTUATOR MOUNTING OPTIONS
DETAIL A1
DETAIL A2
DOUBLE FLANGE
(FRONT & REAR)
OFFSET FLANGE
The details to the left show the standard arrangements for
both internally mounted and externally mounted actuator
options. Detail A1 shows the actuator externally mounted
on a standard 6" damper output shaft. Any internally mounted actuator or multiple section assemblies require the use
of a jackshaft. Detail A2 shows two actuators, externally
mounted, on a jackshaft. When multiple actuators are used
on the same jackshaft, they are factory wired in series.
Detail A3 shows a standard single section assembly with an
externally mounted actuator, while detail A4 shows a single
actuator mounted Internally on a multiple section assembly.
Note: Up to three actuators may be installed on a multiple
section IAQ50X assembly. This limits a standard IAQ50X
assembly to 56 square feet (consult the factory if your application exceeds actuator limitations).
DETAIL A3
DETAIL A4
The envelope dimensions to the right are typical for all units with a B-Height
dimension over 20” (508). On shorter units the actuator is rotated 90° to help
keep the actuator within the overall frame dimension. Consult factory if your
application requires a special actuator mounting arrangement.
6”
(152)
Max.
9”
(229)
Max.
IAQ50X MOUNTING CONFIGURATIONS
Slip-fit duct (typ)
Full Configuration
(shown standard no flanges)
Top & Bottom Configuration
(shown with front flange option)
Flange-mounted duct (typ)
Full Configuration
(shown with double flange option)
Top & Bottom Configuration
(shown with offset flange option)
There are three basic mounting configurations available on the
Ruskin IAQ50X. All three are used in the same application - to
measure and control the minimum outside air to ASHRAE Standard
62.1. Full configuration is typically used in duct runs or in wall
openings. Other dampers may or may not be adjacent to the
IAQ50X in this application. The other two mounting configurations
are for minimum / maximum applications. Typically, the IAQ50X is
AHU Cabinet (typ)
Full Configuration
(shown with front flange option)
Side by Side Configuration
(shown with offset flange option)
used to measure minimum until outside air conditions are suitable
for "free cooling" (economizer mode). Once the "economizer” section is open it is not necessary to validate the minimum airflow
measurement. The details above show some of the more common
mounting configurations. For special configurations or to measure
flow across both the minimum and maximum damper sections,
consult the factory.
CONTROL WIRING & PIPING SCHEMATIC
IAQ50X Frame
IAQ50X
Frame
Side View
IAQ50X
CONTROL
PANEL
IAQ50X
CONTROL
PANEL
Programmable
Controller
Piping/Tubing
Connections
Ruskin's IAQ50X
is supplied and
calibrated
with a
0X
is
dedicated
alibrated
controller
120VAC
dand
Power
actuator.
actuator.
Input Signal
Velocity
Pressure
Sensor
Input Signal
Input Signal
Output Signal
Input Signal
24V Power
120/24VAC
Input Signal
Output Signal
Output Signal
100VA
Input Signal
Pos Signal
24V Power
Pos Feedback
Motor
Actuator
SUGGESTED SPECIFICATION
Furnish and install, at locations shown on plans or as in accordance with schedules, an air measuring station integral to an
extruded aluminum outside air damper. The assembly shall meet
AMCA class 1A leakage of 3 cfm per square foot at 1” water column. The complete air measuring device shall be factory assembled into one turnkey product and calibrated for the specific job
requirements. Unit shall have a measuring range from 150 to 2,000
feet per minute and perform to airflow measurement and leakage
criteria found in ASHRAE Standard 62, IBC and the IECC. The Air
measuring station shall consist of 1/2” x 3" 3000 series aluminum
alloy honeycomb, anodized 6063T6 high yield extruded aluminum
sensing blades with built-in measuring ports and extruded aluminum airfoil control damper blades. The sensing blades shall
remain stationary and shall be perpendicular to the flow at all times.
All pressure tubing shall remain stationary and mounted outside of
the air stream to reduce pressure drop. Tubing that is connected to
moving parts is not acceptable. All sensor tubing shall terminate in
®
3900 Dr. Greaves Rd.
Kansas City, MO 64030
(816) 761-7476
FAX (816) 765-8955
www.ruskin.com
S1
S2
Optional connections to
remote systems/devices (by others)
Over-ride input
Over-ride
Input to
toClose
CloseDamper
Damper--Unoccupied
Unoccupied
Over-ride input
Over-ride
Inputto
toOpen
OpenDamper
Damper--Purge
Purge
0-20mA Output for CFM Indication
0-10VDC Input for CFM Setpoint Adjust
0-10VDC
Auxiliary
0-10VDC Input
Input for
for Auxiliary
Set
Alarm
Set Point
Point Alarm
FOR MORE DETAILED INFORMATION REFER TO THE
ONLINE INSTALLATION AND MAINTENANCE MANUAL AT
WWW. RUSKIN.COM.
solid brass barbed fittings outside the air stream. The integral
damper shall consist of 6063T6 high yield extruded aluminum
blades. Blade edge seals shall be extruded TPR double edge
design with inflatable pocket to enable air pressure to assist in
seal-off and shall be mechanically locked in extruded blade slots.
Adhesive or clip-on type seals are not acceptable. Axle bearings
shall be non-corrosive molded synthetic and shall be molded to fit
the hexagonal damper shaft to reduce leakage. Complete assembly shall be assembled, piped, wired and calibrated in an ISO 9001
certified facility. A factory furnished and calibrated controller shall
be programmed, in nonvolatile EPROM, with the job specific CFM
setpoint and range. The controller and actuator shall communicate
to control to the desired CFM. The controller shall receive a 0-10
VDC input from the BAS and report a 0-10 VDC output that is proportional to the CFM. Air Measuring Stations shall be, in all
respects, equivalent to Ruskin Model IAQ50X.
Printed on recycled paper
using vegetable based inks
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement