sniper x1 vehicle security system

sniper x1 vehicle security system
SNIPER X1 VEHICLE SECURITY SYSTEM
Installation Manual
Table of Contents
1. FEATURES & SPECIFICATIONS ............................................................................................... 2
2. TRANSMITTER BUTTONS: ....................................................................................................... 2
3. FUNCTION .............................................................................................................................. 2
3.1 Key Function:...................................................................................................................2
3.2 Remote Transmitter Code Learning ......................................................................................2
3.3 Programming Features ......................................................................................................2
3.4 ARM MODE: .....................................................................................................................3
3.5 Silent Arm/Disarm ............................................................................................................3
3.6 Shock Sensor Bypass ........................................................................................................3
3.7 DISARM MODE: ................................................................................................................3
3.8 ALARM: ...........................................................................................................................3
3.9 Boot Release ....................................................................................................................4
3.10 Panic Mode ....................................................................................................................4
3.11 Channel 3 Output............................................................................................................4
3.12 Ignition Mode .................................................................................................................5
3.13 Override Mode ................................................................................................................5
3.14 Valet Mode.....................................................................................................................5
3.15 Active/Passive Arming .....................................................................................................5
3.16 Door Lock/Unlock Pulse....................................................................................................5
3.17 Interior Light Delay: ........................................................................................................6
3.18 Auto Rearm....................................................................................................................6
3.19 Anti-hijacking .................................................................................................................6
WIRING DIAGRAM...................................................................................................................... 7
WIRING NOTE ............................................................................................................................ 7
Web Site: www.sniperautomotive.com
HELPLINE: 0906 700 10 20 (All calls charged at 50p/min)
1. FEATURES & SPECIFICATIONS
. Arm / Disarm
. Dual stage shock sensor
. Panic mode / Anti hijacking
. Valet mode
. Auto re-arming
. Ignition locking/Footbrake locking
. Remote door lock / unlock
. Remote boot release (if installed)
. Last door rearming
. Passive locking
. Interior light delay
. Car finder
. Override mode
. Silent arm/disarm
. Door lock/unlock pulse defaults
. Keyless entry
. Channel 3 output
. Automatic and manual anti-hijacking
2. TRANSMITTER BUTTONS:
3. FUNCTION
3.1 Key Function:
PRESS
PRESS
PRESS
PRESS
PRESS
Button
BUTTON 1 ONCE
BUTTON 1 FOR 3 Sec.
BUTTON 2 FOR 2 sec.
BUTTON 1+2 ONCE
BUTTON 2 then 1
Armed
DISARM/UNLOCK
PANIC
BOOT RELEASE
SILENT DISARM
CHANNEL 3
Disarmed
ARM/LOCK
PANIC
BOOT RELEASE
SILENT ARM
CHANNEL 3
Ignition On
LOCK/UNLOCK
BOOT RELEASE
ANTI-HIJACKING
CHANNEL 3
3.2 Remote Transmitter Code Learning
With the alarm disarmed, switch the ignition ON. Within 10 seconds press the valet switch 6 times, after 2
seconds, the siren will chirp for 2 seconds and then the system enters into the code learning mode. Within
another 10 seconds, press any button of the first transmitter, the siren will chirp for 1 seconds and lights flash
twice to confirm the code has been learned. Apply the same procedure within next 10 seconds for the second
transmitter. The system will leave the code learning mode after finishing learning the code for 2 transmitters.
If two transmitters are not programmed, the ignition is switched OFF or the time exceeds the 10-second
programming time, the system will leave the code learning mode.
3.3 Programming Features
Enter programming mode:
1. With the drivers door OPEN, turn the ignition ON then OFF
2. Press valet switch 3 times
3. Wait for siren to sound extended chirp to confirm system is in programming mode
4. Press the valet switch the same number of times as the option number you want to program, waiting for
the corresponding number of chirps after each press.
eg. to program "Channel 3 Output" press the button 6 times as it is option 6 in the programming table.
5. To program this option as described in Column 2 (default) of the table of programming features turn the
ignition ON and wait for 2 seconds until siren sounds an extended chirp.
To program as described in Column 2 turn the ignition ON then OFF and wait for 2 seconds until siren sounds
an extended chirp.
6. The system has now left programming mode, to program another feature repeat steps 1 to 5.
Table of the Programming Features
No.
1
2
3
4
5
6
7
8
Chirp
1 CHIRP
2 CHIRP
3 CHIRP
4 CHIRP
5 CHIRP
6 CHIRP
7 CHIRP
8 CHIRP
Function
IGNITION DOOR LOCK/UNLOCK
DOOR LOCK/UNLOCK TIME
INTERIOR LIGHT DELAY
ACTIVE/PASSIVE ARMING
ALARM TIME
CHANNEL 3 OUTPUT
ANTI HIJACKING
ANTI HIJACKING MODE
Chirp Once
DISABLED
1 SEC.
DISABLED
ACTIVE
30 SEC.
DISABLED
DISABLED
MODE 1
Chirp Twice
ENABLED
4 SEC.
ENABLED
PASSIVE
60 SEC.
ENABLED
ENABLED
MODE 2
3.4 ARM MODE:
With the alarm disarmed, press button (1) when the ignition is off, the siren will chirp once, lights flash once
and doors lock (if connected and depending on the default as 1 or 4 seconds), the LED flashes slowly, the
immobiliser turns on, and the system enters into the arm mode.
3.5 Silent Arm/Disarm
A. Press button (1) and (2) once simultaneously, the system will enter into the silent arm/disarm. The siren
will not chirp. If doors, bonnet or boot are not closed properly, the indicator lights will flash three times and
the LED will flash to indicate that doors, bonnet or boot are not closed properly. The triggers of the above three
sensors will be bypassed until they are closed properly.
B. When the system is silent disarmed and the alarm has been triggered in the users absence, the immobiliser
will turn off, indicator lights flash three times, the siren will chirp four times and the LED flashes the trigger
status. Then the system will enter into the auto rearm mode.
3.6 Shock Sensor Bypass
After pressing button (1) to arm, then press button (1) again within 3 seconds, the siren will chirp once and
the shock sensor will be bypassed.
3.7 DISARM MODE:
A. Disarm Code:
a. When the system is armed, press button (1) once, the siren will chirp twice, lights flash twice and doors
will unlock (if connected). The immobiliser will turn off and the LED flashes rapidly, then the system enters into
the auto rearm mode (ie. The system will rearm itself in 30 seconds if a door is not opened).
b. With the system armed, press button (1) once, the siren will chirp 4 times if there was a trigger in your
absence. The indicator lights will flash three times and the doors will unlock (if connected), the immobiliser
will turn off, the LED will flash trigger memories and then the system enters into the auto rearm mode (ie. The
system will rearm itself in 30 seconds if a door is not opened).
B. Trigger Memory:
If the 2-stage shock sensor triggered -----If boot or bonnet triggered -----------------If doors triggered ---------------------------If ignition triggered --------------------------
LED
LED
LED
LED
is
is
is
is
in
in
in
in
the
the
the
the
cycle
cycle
cycle
cycle
of
of
of
of
flashing
flashing
flashing
flashing
once and off.
twice and off.
three times and off.
four times and off.
C. Clear trigger memories: After pressing the button to disarm, switch the ignition on to clear the trigger
memories.
3.8 ALARM:
A. 1st-stage Shock Sensor Trigger:
When the system is armed the siren will chirp three times when this sensor is triggered. If three constant
triggers are received from the first-stage trigger then the first-stage shock sensor will be bypassed until the
system is rearmed.
B. 2nd-stage Shock Sensor Trigger:
When the system is armed, the siren will sound for 30 seconds when this sensor is triggered. The indicator
ights will flash for 30 seconds, the LED will start a cycle of flashing once and then off, the system will remain
armed. If three constant triggers are received from the second-stage shock sensor, then the second-stage
shock sensor will be bypassed until the system is rearmed.
C. Bonnet or Boot Trigger
a. When the system is armed, the siren will sound for 30 seconds if bonnet or boot is triggered. The siren will
sound for 30 seconds, indicator lights will flash for 30 seconds, the LED will start a cycle of flashing twice and
then off, the system will remain armed.
b. When the system is armed, if bonnet or boot is triggered and then are left open, the siren will alarm for three
cycles with an interval of 3 seconds between each cycle. The system will remain in the armed mode but the
bonnet and boot sensors will be bypassed until they are closed properly.
D. Door Trigger
a. When the system is armed, the system will alarm if the doors are triggered. The siren will sound for 30
seconds, indicator lights will flash for 30 seconds, the LED will start a cycle of flashing three times and then
off, the system will remain in the armed mode.
b. When the system is armed, the system will alarm for 3 cycles if doors are triggered and not closed the siren
will alarm for three cycles with an interval of 3 seconds between each cycle. After 3 alarm cycles, the system
will remain in the armed mode but the door sensors will be bypassed until doors are closed properly.
E. Ignition Trigger
a. When the system is armed, if the ignition is triggered (turned on), the siren will sound for 30 seconds, the
LED will start a cycle of flashing four times and then off, the system will remain in armed mode.
b. When the system is armed, if the ignition is triggered and left turned on, the system will alarm for three
cycles with an interval of 3 seconds between each cycle. After 3 alarm cycles, the system will remain in the
armed mode but the ignition sensor will be bypassed until the ignition is turned off.
F. Alarm Disable:
a. The system will remain in armed mode after the 30-second alarm time.
b. During the alarm being triggered, press button (1) once, the system will disarm. The siren will chirp 4 times,
the immobiliser will turn off, the indicator lights will flash three times, doors unlock (if connected) and the LED
will flash the trigger memories.
3.9 Boot Release
With the alarm armed or disarmed pressing button (2) for over 2 seconds will operate the boot release (where
fitted).
3.10 Panic Mode
A. When the system is armed, press button (1) for over 3 seconds, 3 seconds later the siren will sound for 30
seconds, indicator lights will flash for 30 seconds and the LED flashes rapidly. The system will remain in armed
mode.
B. When the system is disarmed, press button (2) for over 3 seconds, the system will be armed. 3 seconds
later, the siren will sound for 30 seconds, indicator lights flash for 30 seconds and the LED flashes rapidly. The
system will remain in armed mode.
3.11 Channel 3 Output
A. If channel 3 output is programmed as enabled: After the system is armed, the system will send a
30-second signal to the channel 3 output. This can be used for control of total closure on those vehicles with
this feature.
B. If channel 3 output is programmed as disabled: After the system is armed, the system will not send any
signals for channel 3 output automatically after arming but by pressing button (2) then button (1), the system
will send a 30-second signals to the channel 3 output.
3.12 Ignition Mode
*if C2-3 connected to brake light:
A. If the ignition door lock/unlock is programmed as disabled (Footbrake lock)
*When the system is disarmed and the ignition is on, if all doors are closed properly, the doors will be locked
(if connected) when the footbrake pedal is pressed. Once all doors are locked, depressing footbrake pedal
will not activate door locks.
*If any or all doors are not closed properly, depressing the footbrake pedal will not activate door locks.
*When the system is disarmed and the ignition is on, the footbrake lock will be activated once after the doors
are opened and closed doors the footbrake pedal pressed.
*When the ignition is switched off the doors will be unlocked immediately.
B. If the ignition door lock/unlock is programmed as enabled (Ignition door lock)
*When the system is disarmed, after switching the ignition on, doors will be locked after 3 seconds if all doors
are closed properly.
*When the ignition is switched off the doors will be unlocked immediately.
C. When under the ignition mode, pressing button (1) once will also control door lock/unlock.
*if C2-3 NOT connected to brake light:
When Disabled: The doors will not be locked when ignition is turned on or unlocked when ignition is turned
off.
When Enable: The doors will be locked automatically when ignition is turned on and unlocked automatically
when ignition is turned off.
In this case, the doors will not be able to be automatically locked again if the door is opened and closed during
driving.
3.13 Override Mode
When the system is in the armed mode or the alarm is triggering, switch the ignition on, press the valet switch
once and the system will be disarmed.
3.14 Valet Mode
A. With the system disarmed, switch the ignition on, within 10 seconds press the valet switch for over 2
seconds, the LED will turn on and then the system enters into to the valet mode.
B. The anti-hijacking will not be activated when the system is under the valet mode.
C. Under the valet mode, pressing buttons on transmitters will only control door lock/unlock.
D. To leave valet mode, switch the ignition on, within 10 seconds press the valet switch over 2 seconds. The
LED will turn off, the siren will chirp twice and the system will leave the valet mode.
3.15 Active/Passive Arming
A. When programmed as active:
The alarm will only be armed when button (1) is pressed.
B. When programmed as passive:
With the alarm disarmed, after switching the ignition off and the doors are opened and closed the LED will flash
rapidly and the system will enter into the arm mode after 30 seconds. If the doors are opened and closed
again within 30 seconds of LED rapid flashing, the 30-second wait will be re-started.
3.16 Door Lock/Unlock Pulse
A. When the ignition door lock/unlock pulses are programmed as 1 second: door lock/unlock time is 1 second.
B. When the ignition door lock/unlock pulses are programmed as 4 seconds: door lock/unlock time is 4
second.
3.17 Interior Light Delay:
A. When the interior light delay is programmed as disabled:
If doors, boot or bonnet are not closed properly and then the system enters into the arm mode, the siren will
chirp three times, indicator lights flash three times and the doors lock (if connected). The LED will flash the
memory to indicate that doors, boot or bonnet are not closed properly, and then the system enters the arm
mode. The triggers of the above three sensors will be bypassed until they are closed properly.
B. When the interior light delay is programmed as enabled:
If doors are not closed properly, the siren will chirp three times in 20 sec. after entering the armed mode the
LED will flash the memory to indicate that doors are not closed properly. The triggers of door sensors will be
bypassed until they are closed properly. But the siren will chirp three times immediately after entering the
armed mode if the boot or bonnet is not closed properly as per point A.
3.18 Auto Rearm
If triggered, after pressing button (1) to disarm the LED will flash the trigger memories if applicable or the LED
will flash rapidly, the system will be in the auto rearm mode and enter into the arm mode in 30 seconds a door
is not opened.
3.19 Anti-hijacking
A. When anti-hijacking programmed as disabled:
There is no anti-hijacking function.
B. When anti-hijacking programmed as enabled and anti-hijacking as mode 1:
a. When the system is disarmed and the ignition is on, press button (1) and (2) simultaneously, lights will flash
once and the system enters into the anti-hijacking mode. 60 seconds later, the siren will chirp 10 times and
then the alarm starts sounding. The immobiliser will turn on and indicator lights will start flashing. The siren
will alarm for 30 seconds (or 60 seconds) for one cycle. The interval between cycles is 3 seconds. The alarm
will not stop until the anti-hijacking is deactivated. When switch the ignition off during a cycle, the alarm will
sound until the alarming cycle finishes and the system will remain under the anti-hijacking mode. If the
ignition is switched on again, the alarm will sound as described as above.
b. Deactivating the anti-hijacking:
*After the alarm has gone into the anti-hijacking mode, within the 10-chirps or 60-second period, switch the
ignition off and on and press the valet switch once, the anti-hijacking mode will be deactivated.
*After enter into the anti-hijacking mode and while the alarm is sounding, switch the ignition off and on, press
the valet switch for over 2 seconds, the anti-hijacking mode will be deactivated.
C. When anti-hijacking programmed as enabled and anti-hijacking as mode 2:
a. When the system is disarmed and the Ignition is on and a door is opened or closed the indicator lights will
flash once and the system will automatically enter into the anti-hijacking mode. 60 seconds later, the siren
will chirp 10 times and then the alarm starts sounding. The doors will be locked (if connected), the
immobiliser will turn on and the indicator lights will start flashing. The siren will alarm for one cycle. The
interval between cycles is 3 seconds. The alarm will not stop until the anti-hijacking is deactivated. When the
ignition is switched off during a cycle the alarm will sound until the alarming cycle finishes. And the system
will remain in anti-hijacking mode. If the ignition is switched on again the alarm will sound as described as
above.
b. Deactivating the anti-hijacking:
*After the alarm has gone into the anti-hijacking mode, within 10-chirp or 60-second period, switch the
ignition off and on and press the valet switch once, the anti-hijacking mode will be deactivated.
*After enter into the anti-hijacking mode and while the alarm is sounding, switch the ignition off and on, press
the valet switch for over 2 seconds, the anti-hijacking mode will be deactivated.
WIRING DIAGRAM
WIRING NOTE
Central Lock Wiring Diagram
Diagram #A
Original built-in central locking
Negative or Positive
Main Line + or - as required
Diagram #B
Original built-in central locking &
electric lock switch is installed
For example: CHRYSLER
Up
Black
Black
Green
Green
Pink
Pink
White
White
Blue
Blue
Orange
Orange
Original Built-in
Controller
Diagram #C
Original built-in central locking where only
a switch is installed in the drivers door.
A door motor is required.
+12V
Power Lock Switch
On the Front Door
Diagram #D
Original built-in central locking using
a compressor to control the switch.
For example: BENZ, AUDI
(Note: Active time 3.5 sec.)
Black
Green
Black
Green
+12V
Pink
Down
Blue
Pink
Orange
White
Blue
Orange
White
Up
Main Line
Electric Motor
Switch
Up
Down
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement