faucet instllation 2014
Installation Tips & Troubleshooting
PACKAGE CONTENT- (check under the foam packaging on the bottom of the box)
Plastic Holder
Weight Ball
Rubber Ring
Metal Ring
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber’s putty - optional
Pipe tape
Flat screwdrivers
.
Lock Nut
Allen Keys
Hot &Cold Hoses
SAFETY TIPS
If you use soldering for the installation of the faucet,
the seats, cartridges and washers will have to be
removed before using flame. Damage caused
by improper soldering will void the warranty.
Wear safety glasses when soldering
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the hot and cold knobs on the old faucet to
release pressure. When installing your new faucet, turn the connector nuts finger-tight, then use one wrench to anchor the
fitting and a second wrench to tighten the nut. Connections that are too tight will reduce the integrity of the system and
potentially cause product failure which could lead to water damage. Wrap all threaded connections with pipe tape
available at your local hardware store. Always wrap in a clockwise direction. Not all necessary supplies to install your
faucet are included, however, they are available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT &COLD WATER SUPPLY LINES to remove debris, solder or other
impurities which could damage or clog the new faucet, and potentially void the warranty.
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with
a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or damage the
surface material and void the warranty.
INSTALLATION
Installation mut be done by a qualified licensed plumber.
Faucet Installation Reference
1. Shut off water supply.
1
2. Thread female end of the braided hose (HOT & COLD) to the faucet.
Sprayer pipe
Sprayer hose
Sprayer Nut
Connector
ENSURE THAT YOU USE PIPE TAPE AND DO NOT OVER
TIGHTEN THE SUPPLY LINE NUTS AS THIS COULD CAUSE
PRODUCT FAILURE LEADING TO WATER DAMAGE.
3
2
3. Disconnect the sprayer nut connector. Remember
the position as you will need to reconnect them back.
Sprayer hose
4.
Seal rubber
ring
5
Position the faucet in the countertop hole. Insert sprayer pipe, hot
water pipe, and cold water pipe before inserting sprayer hose.
From beneath the countertop hole assemble the plastic holder,
rubber ring, and metal ring in the order depicted in the diagram.
Then thread metal nut and tighten the metal lock nut until the
faucet is secured. Tighten the 2 screws on the lock nut for extra security.
Do not pull the sprayer
hose out too far!
4
Plastic holder
Rubber ring
Metal ring
5. Reconnect the sprayer nut connector and attach to the sprayer pipe by
hand and tighten until is secured.
Lock Nut
Sprayer Nut Connector
6. Attached weight ball to the sprayer hose. It is important to position the weight ball
so it is above the lowest point in the loop leading to the spray.
.
6
7
7. Attached the (HOT & COLD) flexible hoses to the HOT and
COLD water supply.
8. After the installation is complete, turn on the water supply and allow both HOT and COLD water to run
separately for at least two minute each. While water is running, check for leaks. It is important to view the
connections at the male and female flexible hose connections. If leaks are detected, refer back to the instructions
and adjust accordingly. Tightening nuts slightly may stop any minor leaks.
.
Cartridge Replacement
Rings
1. Turn off the water supply to the faucet.
2. Loosen the screw with the Allen key provided and pull out
the handle body.
3. Remove Rings and Cap, and the cartridge will be exposed.
4. Pull the cartridge out and replace it with the new cartridge.
(Remember the positioning of the cartridge)
5. Place the Rings, Caps, Handle back into place, and tighten the screw
back onto the Handle Body with the Allen key. Do not over tighten.
6. Slowly open the water feed to the faucet to test.
Cartridge
Cap
Handle
Body
Screw
Faucet Body
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement