Operating instructions for condenser tumble dryer T 7744 C

Operating instructions for condenser tumble dryer T 7744 C
Operating instructions
for condenser tumble dryer
T 7744 C
It is essential to read these
operating instructions before
installing or using the machine
to avoid the risk of accidents or
damage to the machine.
en - AU, NZ
M.-Nr. 06 605 540
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
or machine
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
Energy saving tips
To avoid unnecessarily long drying
times and high consumption of energy:
– Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
– Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filters are clean
before using the dryer.
– Check the condenser unit from time
to time and clean it when necessary.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
2
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Additional options/Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Low temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Once a programme has started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
- changing the programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
- cancelling the programme and then selecting a different programme . . . . . 20
- cancelling the programme and then removing the laundry . . . . . . . . . . . . . . 20
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 20
Time remaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electronic system lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Emptying the condensed
water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning them with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Checking the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3
Contents
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Check and fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
After Sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 36
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Room ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Before moving the machine again
(e.g. when moving house) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Arranging the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
External drainage via a sink or gully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation conditions requiring a non-return valve . . . . . . . . . . . . . . . . . . . . . 39
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Extending the range of the drying levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Altering the volume of the buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Clean out airways indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Adjusting the dryer's electronics for very soft water . . . . . . . . . . . . . . . . . . . . . . . 51
4
Warning and Safety instructions
~ It must only be used as a domestic
~ It is essential to read these
instructions.
This tumble dryer conforms to
current safety requirements.
Inappropriate use can, however,
lead to personal injury and damage
to property.
To avoid the risk of accidents and
damage to the tumble dryer, please
read these instructions carefully
before using it for the first time. They
contain important information on its
safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
appliance to dry items which have been
washed in a water solution and which
are marked on the manufacturer's care
label as being suitable for tumble
drying. "Dry cleaning kits" for
freshening up garments in a tumble
dryer are increasingly available on the
market. If using, do so at your own risk,
and follow the instructions provided on
the packaging.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the tumble
dryer..
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it correctly by a
person responsible for their safety.
Safety with children
Correct application
~ This tumble dryer is not designed for
~ Keep children away from the tumble
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
dryer at all times. It is not a toy! To
avoid the risk of injury do not allow
them to play on or near it or to play with
its controls. Supervise children whilst
you are using it.
– Shops
~ Older children may only use it if its
– Offices and showrooms
and by residents in establishments
such as
operation has been clearly explained to
them, and they are able to use it safely,
recognising the dangers of incorrect
use.
– Hostels and guest houses
5
Warning and Safety instructions
Technical safety
~ Before setting up the tumble dryer,
check it for any externally visible
damage.
Do not install or use a damaged tumble
dryer.
~ Before connecting the tumble dryer,
ensure that the connection data on the
data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
~ The electrical safety of this tumble
dryer can only be guaranteed when
continuity is complete between it and
an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and
where there is any doubt the household
wiring system should be inspected by a
qualified electrician. Miele cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
~ Do not connect the tumble dryer to
the mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
tumble dryer (e.g. danger of
overheating).
~ Unauthorised repairs could result in
unforeseen dangers for the user, for
which Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
tumble dryer until after maintenance or
repair work has been carried out.
6
~ Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
tumble dryer be guaranteed.
~ If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
~ In the event of a fault or for cleaning
purposes, the tumble dryer is only
completely isolated from the electricity
supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is disconnected, or
the screw-out fuse is removed (in
countries where this is applicable).
~ This tumble dryer may only be used
in mobile installations such as ships if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the tumble dryer and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the guarantee.
~ Do not make any alterations to the
tumble dryer, unless authorised to do
so by Miele.
Warning and Safety instructions
Correct use
,To avoid the possible danger of
fire please read these warnings
carefully.
,A clogged filter is a fire hazard!
The lint filter must be cleaned after
every program.
~ Remove all objects from pockets
such as lighters and matches.
~ To prevent the risk of fire, the
following textiles must not be dried in
this tumble dryer:
– Items which have not been washed.
– Items, such as workwear, which have
not been thoroughly cleaned and
which are still soiled with grease, oil
or other desposits (such as
cosmetics, lotions etc).
If items have not been thoroughly
cleaned there is a danger that these
might ignite when heated, even after
they have been removed from the
dryer at the end of the programme.
– Items that have been soiled with
substances such as cooking oil,
acetone, petrol, kerosene, spot
removers, turpentine, waxes, wax
removers and other chemicals (e.g.
mops and floor cloths)should be
washed in hot water with extra
amount of detergent before being
dried in the tumble dryer.
– Items which have been splashed
with hair lacquer, hair spray, nail
polish remover or similar substances.
When washing such heavily soiled
items ensure that you use sufficient
detergent and select a high
temperature. If in doubt, wash the
items several times.
~ Oil-affected items can ignite
spontaneously, especially when
exposed to heat sources such as in a
tumble dryer.
The items become warm, causing an
oxidation reaction in the oil. Oxidation
creates heat.
If the heat cannot escape, the items
can become hot enough to catch fire.
Piling, stacking or storing oil-affected
items can prevent heat from escaping
and so create a fire hazard.
If it is unavoidable that fabrics that
contain vegetable or cooking oil or
have been contaminated by hair care
products be placed in a tumble dryer
they should first be washed in hot water
with extra detergent - this will reduce,
but not eliminate, the hazard.
7
Warning and Safety instructions
~ To prevent the risk of fire, the
following textiles or products must not
be dried in this tumble dryer:
– Items which have been dry-cleaned
(for example with a chemical
treatment).
– Fabrics which contain a large
proportion of rubber, foam rubber or
rubber-like materials. For example,
products made from latex foam
rubber, shower caps, waterproof
textiles, rubberised articles and items
of clothing and pillows with foam
rubber filling.
– Fabrics which contain padding or
fillings (e.g. pillows, jackets). If these
were damaged the filling could get
out with the risk of igniting in the
dryer.
~ In many programmes, the heating
phase is followed by a cooling down
phase to ensure that the items are not
too hot to handle when you remove
them (this also avoids the danger of the
laundry self-igniting). The programme is
not finished until the cooling down
phase is complete.
Ensure that you always wait until the
end of the programme before removing
the laundry.
8
~ Warning: Do not switch the tumble
dryer off before the end of the drying
programme. If this was done and the
laundry was then removed immediately,
it could give off a great amount of heat.
~ Fabric conditioner and similar
products must be used according to
the instructions on the manufacturer's
packaging.
Warning and Safety instructions
~ The dryer must not be used without
the fluff filters in place or if the fluff
filters are damaged in any way.
~ The fluff filters must be cleaned
regularly.
~ Always keep the area around the
tumble dryer free of dust and fluff. Dust
drawn into the tumble dryer can cause
blockages in the condenser unit over
time.
~ The dryer must not be used without
~ Do not let anyone sit or lean on the
~ The fluff filters must be thoroughly
dried after cleaning. Damp or wet filters
could cause operational faults.
~ Always close the door after use. This
~ Do not install the tumble dryer in a
– Children climbing onto or into the
dryer or hiding things in it.
the condenser unit in place.
room where there is a risk of frost
occurring. At temperatures around
freezing point the tumble dryer may not
be able to operate properly.
There is a risk of damage if the
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
The ambient room temperature should
be between +2°C and +35°C.
~ If the water is drained externally
through the drain hose instead of being
collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.
~ Condensed water is not drinking
water.
It can cause health problems in both
people and animals.
door, as this can cause the tumble
dryer to tip up.
way you will avoid the danger of:
– Pets or other small animals climbing
into it.
~ The tumble dryer must not be hosed
down.
Accessories
~ Only use genuine Miele spare parts
and accessories with this appliance.
If non-Miele parts are used, guarantee,
performance and product liability
claims may be invalidated.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
9
Operating the tumble dryer
Control panel
a Display
b Delay start button
This button is used for:
- Selecting the duration of the
Warm air and Cool air
programmes
- Delaying the start of a programme
c Buzzer button
An audible tone sounds at the end of
the programme.
d Check lights
These indicator lights have various
functions. See "Problem solving
guide" / "After sales service" for
details.
e Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
The button flashes while a
programme is being selected and
then is on constantly when the
programme has started.
10
f Low temperature button
Delicate fabrics are dried at a lower
temperature.
g Drying level button
with indicator lights
h Programme selector
with indicator lights
i Door button
Pressing this button will open the
door even when the machine is
switched off at the mains.
j I-On/0-Off button
For switching the dryer on and off.
Operating the tumble dryer
Display
The following are selected via the
display:
– Delay start
– Duration of the Cool air and Warm air
programmes
In the same way, the Woollens
handcare, Silks handcare and
Smoothing programmes can finish
earlier than expected if a certain
temperature is reached. This can
happen with particularly fine fabrics,
very small loads or if items were partly
dry beforehand.
– Programmable functions
The display also shows:
Delay start
– Programme duration
The delay start time selected will
appear in the display.
– Programme stage
Drying
Cooling down
Finish
After the Start/Stop button has been
pressed, the delay start time will start
counting down.
– Check and fault messages
Programme duration / Estimated time
remaining
When a programme is selected, the
estimated duration (time remaining) will
appear in the display. Please be aware
that it is only an estimate!
The following factors all affect the
estimated time remaining: residual
moisture content after spinning; type of
fabric; size of load; room temperature;
fluctuations in power supply.
Once the delay start time has elapsed,
the programme will begin and the
estimated programme duration will
appear in the display.
Programmable functions
The programmable functions can be
used to tailor drying programmes to suit
your individual requirements. In
programming mode, the display will
show the function selected.
The electronics continually assess
conditions in the dryer and adjust the
estimated time remaining for a more
accurate reading. Because of this, the
time displayed can alter during the
course of a programme.
11
Notes on laundry care
Care symbols
Before drying check the drying
symbol on the care label. If there are
no symbols, dry at your own risk!
q . . . . . . . . . Dry at normal temperature
r . . . . . . . . . . Dry at a low temperature
s . . . . . . . . . . . . . . . Do not tumble dry
– Cottons, linens and minimum iron
items should be dried using the
appropriate programme for the
degree of dryness required.
– For delicates and fabrics with the
following care label r select the Low
temperature extra option.
Tips on drying
Always observe the maximum
recommended loads given in the
"Programme chart". Never overload
the drum. Overloading can cause
unnecessary wear and tear to the
laundry, give a disappointing drying
result and cause more creasing.
Do not put soaking wet items into the
tumble dryer. Spin them thoroughly
after washing using the appropriate
spin speed.
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be partially dried using the Woollens
hand care programme.
12
– Down-filled garments have linings
which have a tendency to shrink,
depending on the quality of the item.
They can be partially dried using the
Smoothing programme.
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may
otherwise become rough. They can
be partially dried using the
Smoothing programme.
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry
these textiles. When purchasing
these garments it is advisable to take
their shrinkage properties into
account.
– Minimum iron fabrics and 100%
cotton shirts or blouses tend to
crease more the greater the load.
This is especially true of very fine
weaves, such as shirts or blouses.
Reduce the load or use the Shirts
programme.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– New dark coloured garments should
be washed and dried separately
from light coloured garments to avoid
the danger of colours running and
discolouring other garments or even
plastic components in the machine.
Dark coloured fibres can also settle
on light coloured garments and vice
versa.
How to dry correctly
Brief instructions
C Load the tumble dryer
The headings numbered (A, B, C ...)
show the operating sequence and can
be used as a brief guide to using your
dryer.
^ Press the door button to open the
door.
^ Load the laundry loosely into the
drum.
A Sort the laundry
To ensure an even drying result
separate out the washed laundry and
sort it according to:
. . . the drying level required
. . . the type of fibre or weave
. . . size
. . . the moisture content after spinning.
,Make sure that objects e.g.
detergent dispensing balls have
been removed from the laundry.
They could melt, and cause damage
to the dryer or the laundry.
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
^ Before closing the door make sure
the fluff filter is correctly positioned in
the door.
– Remove all objects from pockets
such as lighters and matches.
– Check seams and stitching to ensure
that padding and linings are intact.
– Fasten duvet covers and pillow
cases to prevent small items from
being trapped inside them.
– Fasten zips, hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
B Turn on the tumble dryer
^ Switch the dryer on by pressing the
I-On/0-Off button in.
The tumble dryer may be switched on
after loading, saving energy as the light
will not come on.
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
13
How to dry correctly
D Select a programme
^ Press the Drying level button
repeatedly until the indicator light for
the drying level you want lights up.
Any of the drying levels can be
selected for the Cottons programme. A
more limited range is available when
using other programmes.
^ Select the programme you want.
The Cottons Normal Plus program is
recommended for a normal load and is
the program used in energy
consumption tests in accordance with
AS/NZS 2442.1 (refer to
www.energyrating.gov.au for
consumption data)
The indicator light for the programme
selected will light up.
A drying level or additional option(s)
indicator light may also light up, or a
time may appear in the display
(Memory function).
Programmes with drying levels:
Cottons, Minimum iron, Delicates,
Automatic, Shirts, Denim
Important: Please note that the
programme duration shown in the
display will vary according to the
programme selected (see "Programme
duration / Estimated time remaining").
You cannot alter the drying level of the
Woollens handcare and Smoothing
programmes.
Cool air and Warm air programmes
The indicator light for the Delay start
button will flash when the Cool air or
Warm air programme is selected.
^ Press the Delay start button
repeatedly until the required duration
shows in the display.
You can select a duration of 20 minutes
up to 2 hours in 10 minute steps.
E Select any additional options
^ The Low temperature, Buzzer, and
Delay start additional options are
selected by pressing the appropriate
button (see "Additional options" for
more details).
N.B.: It is not possible to select Delay
start when using the Warm air or Cool
air programme.
14
How to dry correctly
F Start the programme
The Start/Stop button will flash when a
programme is being selected. The
flashing indicates that a programme
can be started.
^ Press the Start/Stop button.
The Start/Stop button will now light up
constantly.
Drying will appear in the display and
the time remaining will start counting
down.
Before the end of a programme
There is a cooling down phase at the
end of the drying sequence (Cooling
down will light up in the display). The
programme will not finish until the
cooling down phase has been
completed.
There is no cooling down phase at the
end of the following programmes:
Woollens handcare, Smoothing.
G Remove the laundry when the
programme has finished
0 and Finish will appear in the display
to indicate that the programme has
finished. The buzzer (if selected) will
sound at intervals.
The drum will continue to rotate at
intervals to prevent laundry creasing,
if you do not wish to remove it
immediately (anti-crease). The
anti-crease phase lasts for an
hour. There is no anti-crease phase at
the end of the Woollens handcare
programme.
^ Press the Door button.
^ Open the door.
^ Remove the laundry.
Check that all items have been
removed from the drum. If items are
left in the dryer, they could be
damaged by overdrying when the
dryer is next used.
If the dryer is switched on at the mains
and the door is opened, the drum
lighting will come on. It will go out a few
minutes later to save energy.
^ Switch the dryer off by pressing the
l-On/0-Off button.
^ Clean the fluff filters.
^ Close the door.
^ Empty the condensed water
container (unless the dryer has been
connected for external drainage).
^ The condenser unit should be
checked and cleaned on a regular
basis.
15
Additional options/Delay start
Low temperature
For all delicate or minimum iron
fabrics with the r symbol on the
care label (e.g. acrylic garments).
– The programme duration is longer.
– On some programmes Low
temperature is a standard part of the
programme and so cannot be
deselected.
Buzzer
A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.
The buzzer will still sound if there is a
fault, even if it has been switched off.
Delay start
The start of a programme can be
delayed by 30 minutes up to 24
hours.
After selecting a programme:
To begin delay start
^ Press the Start/Stop button.
– The Delay start indicator light will
light up constantly.
The delay start time counts down
towards the start of the programme as
follows:
– more than 10^ by the hour
– less than 10^ in minutes
The drum will turn briefly every hour to
help prevent creasing.
While the delay start time is counting
down, you can still add laundry to the
drum:
^ Switch the dryer off.
^ Open the door and add the laundry.
^ Close the door and switch the dryer
back on again.
To cancel/alter delay start
^ Press the Start/Stop button.
This cancels delay start.
^ Press the Delay start button
repeatedly until the required delay
period shows in the display.
^ To alter the delay start time, press the
Delay start button repeatedly until the
required delay period shows in the
display.
– The Delay start indicator light will
flash.
^ Press the Start/Stop button.
– Times of:
up to 10^ are selected in 30 minute
steps
more than 10^ in 1 hour steps
– If you keep the Delay start button
pressed in, the time will continue to
increase up to 24^.
16
^ The altered delay start time will start
counting down from the beginning
again.
Programme chart
Max. load: 6 kg*
Cottons
Extra dry, Normal
Fabric type
Single and multi-layered cotton fabrics such as towelling,
jerseywear, T-shirts, underwear.
Notes
– Select Extra dry for multi-layered and very thick fabrics.
– Do not use Extra dry for jersey fabrics (e.g. T-shirts,
underwear), as they have a tendency to shrink.
Low temperature
Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
Hand iron, Machine iron
Fabric type
Cottons or linen fabrics, e.g.: table linen, bed linen, starched
laundry.
Note
– To prevent laundry from drying out it should be rolled up
until you are ready for ironing.
Low temperature
Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
Max. load: 3 kg*
Minimum iron
Extra dry, Normal, Hand iron
Fabric type
Minimum iron items made of cotton, synthetic or blended
fabrics, e.g.: shirts, blouses, skirts and table cloths.
Notes
– Select Hand iron for delicate fabrics and to reduce
creasing even more, reduce the load to 1.5 kg*.
– In the Minimum iron programme with the Hand iron drying
level, items are dried with very little creasing, depending
on fabric type and amount of laundry.
Low temperature
Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
Max. load: 2 kg*
Delicates
Normal, Hand iron
Fabric type
Delicate items made of synthetic fibres, easy care cotton or
blended fabrics, e.g. shirts, blouses and evening wear with
sequins and beading.
Low temperature
Low temperature cannot be deselected.
* Weight of dry laundry
17
Programme chart
Woollens handcare
Max. load: 2 kg*
Fabric type
Woollen fabrics
Notes
– This programme only fluffs up woollen garments. They are
not dried completely by this programme.
– Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.
Low temperature Low temperature cannot be deselected.
Max. load: 3 kg*
Smoothing
Fabric type
– Cotton and linen fabrics.
– Minimum iron items made of mixed fibres, cottons or
synthetics, e.g.: trousers, jackets, shirts.
Notes
– Smooths out creasing caused during the spin cycle in the
washing machine.
– Fabrics are not completely dried in this programme.
Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.
Low temperature Low temperature cannot be deselected.
Max. load: 3.5 kg*
Automatic
Normal, Hand iron
Fabric type
Mixed loads of garments suitable for the Cottons and
Minimum iron programmes. Sort according to colour.
Max. load: 2 kg*
Shirts
Normal, Hand iron
Garments
Shirts and blouses.
Low temperature Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
Max. load: 3 kg*
Denim
Normal, Hand iron
Fabric type
Denim garments, e.g. jeans, jackets, skirts, shirts.
Low temperature Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
* Weight of dry laundry
18
Programme chart
Max. load: 6 kg*
Cool air
Fabric type
Warm air
– Any item which only needs airing.
Max. load: 6 kg*
Fabric type
– "Voluminous" and multi-layered fabrics whose layers have
different drying characteristics, e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, bathing
costumes, tea-towels and small loads.
Note
Do not select the longest drying time to start with. Check the
items as you are drying them to find the optimum time.
Tip
You can use the Warm air programme to help remove odours
from cotton clothing which has been worn but it still clean
(select a duration of between 1/2 and 1 hour). Items must be
suitable for drying in a tumble dryer. Dampen the garments a
little beforehand or add a fabric conditioner sheet. The Warm
air programme will not be as effective at removing odours
from any parts of the garments which are made of synthetic
fibres.
Low temperature Also select the Low temperature option for delicate fabrics
with the r symbol on the care label.
* Weight of dry laundry
19
Changing the programme sequence
Once a programme has started
- changing the programme
You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).
You will need to cancel the current
programme before you can select a
new one.
- cancelling the programme and then
selecting a different programme
^ Press the Start/Stop button.
The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.
If you press the Start/Stop button
again during the cooling down
phase, Finish will light up in the
display.
^ Switch the dryer off.
^ Switch the dryer on.
^ Select another programme and start
it.
- cancelling the programme and then
removing the laundry
^ Proceed as described in "Adding or
removing laundry after a programme
has started" below.
^ Switch the dryer off after closing the
door.
20
Adding or removing laundry
after a programme has started
^ Press the Door button.
^ Open the door.
,Danger of burning:
Do not touch the back of the drum
when adding or removing items. The
drum and the items can get very hot.
^ Add or remove items as required.
^ Close the door.
^ Press the Start/Stop button.
Time remaining
The time left shown in the display may
now vary from the actual drying time.
Electronic system lock
It can be activated if wished.
D Now slowly turn the programme
selector six positions stage by stage
in an anti-clockwise direction.
Each of the six programme indicator
lights must come on one after the
other.
The dryer's electronics are then locked.
The dryer can still be switched on but a
programme cannot be started.
The indicator light for the Low
temperature button will flash and a key
symbol 0-§ will appear in the display.
– If an attempt is made to start a
programme, the indicator light for the
Low temperature button will come on
and a key symbol 0-§ will appear in
the display.
E Release the Low temperature button.
The system lock prevents your
machine being used without your
knowledge.
The electronics have now been locked.
^ Switch the dryer off.
The door is not locked and can be
opened at any time.
To deactivate the lock
To activate the lock
– The tumble dryer is switched off.
Before you begin, first ensure that:
– The door is closed.
Before you begin, first ensure that:
– The door is closed.
^ The procedure is the same as for
activating the lock. Carry out steps A
to E as described previously.
A Press the Low temperature button
and keep it pressed in whilst carrying
out steps B to E.
At step E the indicator light for the Low
temperature button will stop flashing
and the key symbol 0-§ will go out.
B Press the I-On/0-Off button in.
The electronics are no longer locked.
– The tumble dryer is switched off.
The Automatic indicator light will come
on.
C Slowly turn the programme selector
three positions stage by stage in a
clockwise direction.
Each of the three programme
indicator lights must come on one
after the other.
21
Cleaning and care
Emptying the condensed
water container
The condensed water will be collected
in the condensed water container
unless the appliance has been fitted
with a drain hose (see "Installation").
Empty the condensed water
container after every drying
programme.
The Empty out container indicator light
will come on if the maximum level of the
condensed water container is reached.
The indicator light will go out when the
door is opened and closed again.
,Close the door fully.
Otherwise the door and the front
panel of the condensed water
container could suffer damage when
pulling the container out.
^ Pull out the container.
^ Hold it at the front and towards the
back and keep it in a horizontal
position when carrying it.
22
^ Empty the container.
^ Replace the container in the dryer.
,Condensed water should not be
consumed. It could lead to health
problems for people and animals.
Condensed water can be put to
household use (e.g. in a steam iron or
humidifier). To ensure that any residual
particles of fluff in the condensed water
are removed before use, pass it
through a fine sieve or paper filter first.
Cleaning and care
Cleaning the fluff filters
The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after each drying
programme*.
Cleaning them whilst dry
Tip: You can also use a vacuum
cleaner to remove the fluff.
^ Remove any fluff from the hollow part
of the door opening. You could also
use a cleaning brush which is
available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department, or use a vacuum
cleaner.
^ Also clean the door seal (2) with a
damp cloth.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Open the door and pull the fluff filter
(1) out of the door as illustrated.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the two fluff
filters in the door opening.
^ Close the door.
* Always check the fluff filters if the
Clean out airways indicator light
comes on.
,A clogged filter is a fire hazard!
^ Use your fingers to remove the fluff
from the surface of the filter.
The lint filter must be cleaned after
every program.
23
Cleaning and care
Cleaning them with water
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
^ Open the door and pull the fluff filter
out of the door as described
previously.
The two filters in the door opening can
also be removed if you need to clean
them with water.
,Do not replace them if they are
damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
^ Replace the filters in the door
opening by first inserting them at the
bottom and then pressing them into
place at the top.
^ Lock both dials.
Cleaning the tumble dryer
Disconnect the machine from the
mains electricity supply.
^ Clean the housing and control panel
with a slightly damp cloth and a mild
detergent or soapy water.
^ Turn dial a and pull the filter by the
dial out of the door opening as shown
b. Do the same on the other side.
^ Rinse all the filters under hot, running
water.
^ Then shake the filters until no more
water droplets are visible.
^ Dry the filters thoroughly with care.
^ Clean the area underneath these
filters, e.g. with a vacuum cleaner.
24
^ The drum and other stainless steel
parts can be cleaned with a suitable
propietary stainless steel cleaner
following the manufacturer's
instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts. The machine must never be
hosed down.
^ Dry all parts with a soft cloth.
Cleaning and care
Cleaning the condenser unit
Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.
Check the condenser unit at least
twice a year. Always check it if the
Clean out airways indicator light
comes on. If the dryer is used
frequently then check the condenser
unit after approx. 100 drying cycles.
Clean it if necessary.
Removing the condenser unit
^ Turn the lever on the inner cover
downwards to the vertical position.
^ Tilt the cover forwards.
^ Remove it by pulling it diagonally
upwards.
^ Open the service panel.
^ Now remove the panel by pulling it
diagonally upwards and place it to
one side.
^ Turn the lever on the condenser unit
upwards to the vertical position.
25
Cleaning and care
If you cannot see any fluff:
^ Replace the condenser unit (see
following page).
If you can see some fluff:
^ Clean the condenser unit as
described below.
Cleaning the condenser unit
^ When rinsing the condenser unit,
make sure you position it as
shown in the next two illustrations.
^ Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit
^ Use a shower head or similar to rinse
the unit out as shown.
^ Hold the condenser unit up to the
light as shown.
^ Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.
26
Cleaning and care
Replacing the condenser unit
^ With the handle facing upwards,
push the condenser unit back into
position in its housing.
^ Turn the lever down to the horizontal
position, making sure that the hook
on the lever clicks into the groove.
When replacing the inner cover after
cleaning, ensure that the rubber seal
fits correctly into the groove.
^ Then flush the unit through from the
front.
^ Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
^ Remove any soiling still visible inside
the housing unit.
^ Also make sure the rubber seals are
clean.
The rubber seals must not be
removed and must be free of kinks.
^ Shake any excess water out of the
unit until no more water droplets are
visible.
^ Replace the cover making sure the
hooks locate correctly. Hold it at an
angle and push it gently downwards.
^ Then turn the lever upwards into the
horizontal position to lock the cover.
^ Replace the service panel and press
the upper edge until it clicks into
position.
It is important to ensure that both the
condenser unit and the cover are
correctly positioned and locked.
Otherwise water may leak from the
machine.
27
Problem solving guide
With the help of the following notes, minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in strict accordance with current local and national
safety regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
Check and fault messages
Problem
The programme stops
and 0 appears in the
display.
The buzzer sounds.
The Low temperature
indicator light starts
flashing after the dryer
has been switched on
and 0-§ appears in the
display.
The programme stops
and Cooling down or
Finish flashes in the
display.
The buzzer sounds.
28
Possible cause
This is not a fault.
The electronic unit has
recognised that there is
no laundry in the drum
and cancelled the
programme.
Drying individual
garments or items which
are already dry can also
cause the programme to
be cancelled.
The electronic system
lock is activated.
No obvious cause.
Remedy
– Use the Warm air
programme (timed
drying) to dry individual
items.
To delete the fault
message:
– Open and close the
door.
You will need to
deactivate the system
lock before the dryer can
be used (see "Electronic
system lock").
– Switch the dryer off
and then on again.
– Then start the
programme again.
If the programme stops
again and Cooling down
or Finish flashes again
there is a fault. Contact
the Miele Service
Department.
Problem solving guide
Problem
Possible cause
Remedy
The Clean out
airways indicator
light comes on.
This indicator light comes
on to warn you that the
dryer is not working
efficiently.
Possible cause: The fluff
filters are clogged with
fluff or with detergent
residues.
The programme
stops.
The Clean out
airways indicator
light comes on.
The buzzer
sounds.
See above for possible
causes and their
remedies.
The Empty out
container
indicator light
comes on.
The buzzer
sounds.
The condensed water
container is full or there is
kink in the drain hose.
– Cleaning the fluff filters is
usually all that is required.
However, if the Clean out
airways indicator light does
not go out after you have
cleaned the filters, then also
check all the possible
causes described under
"The drying process goes on
too long or even switches
off".
To switch off the indicator
light:
– Open and close the door.
– Switch the dryer off and then
back on again.
The Clean out airways
indicator light can be
deactivated (see
"Programmable functions").
To switch off the indicator
light:
– Open and close the door.
– Switch the dryer off and then
back on again.
– If the Clean out airways
indicator light comes on
again, contact the Miele Service Dept.
– Empty out the condensed
water container.
– Check the drain hose.
To switch off the indicator
light:
– Open and close the door.
29
Problem solving guide
Other problems
Problem
The drying
process goes
on too long or
even switches
off.
In some
circumstances,
the Clean out
airways
indicator light
still comes on,
even though
the filters are
clean.
Possible cause
Remedy
Please check all the possible causes and switch the dryer
off and then back on again.
Ventilation to and from the dryer
may be insufficient (e.g.
because it is installed in a small
room). This has caused the
temperature in the room to rise
sharply.
The fluff filters are clogged up
with fluff or were still wet when
they were replaced.
Open a door or window while
the machine is in operation
for increased air flow.
– Remove any fluff.
– The fluff filters must be
completely dry.
The laundry has not been spun Make sure that your laundry is
sufficiently.
thoroughly spun at the
appropriate spin speed.
The tumble dryer has been
overloaded.
Do not exceed the maximum
load for the programme
selected.
Metallic components, e.g. zips – Open zips next time.
have prevented the dryer from If the problem occurs again,
registering the correct moisture dry garments with long zips
level in the laundry.
using the Warm air
programme (timed drying).
Detergent residues, hair and
Check the condenser unit
fine fibres can block up the
from time to time and clean it
condenser unit.
if necessary.
The vents below the door are
blocked.
The laundry is The load consisted of different
not sufficiently fabrics.
dry.
30
Remove any objects that are
blocking the vents.
– Finish drying using the
Warm air programme.
– Select a different
programme next time.
Problem solving guide
Problem
Possible cause
Remedy
– The inner cover of the – Ensure that the
condenser unit has not
condenser unit is
been locked properly
positioned correctly
and/or the condenser
and lock the inner
unit has not been
cover.
positioned correctly.
– Check the rubber
seals.
– Fluff has collected in
the condenser unit
– Use a cloth to remove
housing.
any visible fluff from the
inside of the condenser
unit housing.
Items made of synthetic Synthetic fibres tend to
Static charge can be
fibres are charged with attract static charge.
reduced by adding a
static electricity after
fabric conditioner to the
drying.
final rinse in the washing
programme or a fabric
conditioner sheet to the
load when drying.
Water leaks from the
machine after the
condenser unit has
been cleaned.
There is a build-up of
fluff.
Fluff is principally the
result of friction when
garments are being worn
and washed. Machine
drying hardly causes any
fluff to form and has been
established by research
institutes to have no
appreciable effect on the
lifetime of fabric.
Fluff is collected by the
fluff filters and can be
easily removed (see
"Cleaning and Care").
31
Problem solving guide
Problem
Possible cause
The tumble dryer fails to No obvious cause.
start when switched on.
The interior drum
lighting does not come
on.
The lighting switches off
automatically (to save
energy).
The lamp needs
changing.
32
Remedy
– Is the dryer switched
on?
– Is the plug correctly
inserted into the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Switch the dryer off and
then on again.
Change the lamp as
described at the end of
this section.
Problem solving guide
Changing the lamp
Disconnect the machine from the
mains electricity supply.
The lamp specification and
maximum wattage is stated on the
data plate and on the lamp cover.
^ Open the door.
^ Replace the lamp.
You will find the interior lamp cover at
the top of the drum aperture.
^ To close the cover push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.
^ Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
33
After Sales service
In the event of any faults which you
cannot remedy yourself, please contact
– Your Miele Dealer or
– The nearest Miele Service
Department (see back cover for
address).
When contacting the Service
Department, please quote the Model
and Serial numbers both of which are
located on the data plate (visible when
the door is opened).
Future updates (PC)
The indicator or check light marked PC
on the fascia panel is the interface used
by the Miele service technicians during
service work for testing purposes and
for updating the machine's programme
data.
Optional accessories
Optional accessories for these dryers
are available from your Miele Dealer or
from the Miele Spare Parts Department.
Please note that telephone calls may be
monitored and recorded to improve our
service.
34
Installation and connection
Front view
a Mains connection cable
f Four height adjustable screw feet
b Control panel
g Air inlet and outlet vent for cooling
the condenser unit
c Condensed water container
d Door
e Service panel for condenser unit
h External drainage options (e.g. via
wash basin, wash basin drain outlet
or gully)
35
Installation and connection
Rear view
,The appliance must not be
installed behind a lockable door, a
sliding door or a door with a hinge
on the opposite side to that of the
tumble dryer, in such a way that a
full opening of the tumble dryer door
is restricted.
Transporting the machine to its
installation site
,Important. The cavity under the
a Protruding lid for holding when
moving the machine (see arrows)
b Air inlet vent for cooling the
condenser unit
c Mains connection cable
d External drainage of the condensed
water
e Accessories for connection to a sink
drain outlet
Installation site
,The machine lid must not be
removed.
The dryer can be pushed under a
worktop with its lid in place, providing
the worktop is high enough.
lid which can be seen when the
condensed water container is
removed must not be used to carry
or lift the machine. This could
damage the machine.
Do not hold the machine by the door
to carry it.
When moving the machine, hold it by
the lid where it protrudes to the rear of
the dryer. To manoeuvre the dryer out
of its packing case to its installation site
you will also need to hold it by the front
feet.
Washer-dryer stack
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. The
appropriate "WTV" stacking kit
(available to order) to match your dryer
is required.
,Stacking kits must only be
installed by a suitably qualified fitter.
36
Installation and connection
Levelling the machine
,The air inlet and outlet vents on
the front and back of the machine
must not be covered as this would
prevent sufficient ventilation for
cooling the condenser unit.
,The gap between the base of the
dryer and the floor must not be
minimised by a plinth or thick-piled
carpet as this will prevent a
sufficient intake of cold air.
Room ventilation
The machine must be perfectly level to
ensure safe and proper operation.
The air which is taken in when the
dryer is in operation is blown out of
the vents on the front of the machine
and warms up the air in the room.
It is very important, particulary if the
room is small, to ensure adequate
ventilation. Opening a window, for
example, will allow more air to enter
the room. Otherwise running times
and energy consumption could be
increased.
Before moving the machine again
(e.g. when moving house)
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the machine is tipped up when it
is being moved. It is a good idea to run
the Cool air programme for
approximately 1 minute before moving
the machine. Any remaining condensed
water will then be fed into the
condensed water container or out
through the drain hose.
37
Installation and connection
External condensed water
outlet
General notes
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose at
the back of the dryer. The condensed
water can also be drained off directly if
the machine is installed near a sink, drain
outlet etc. so that the condensed water
container does not have to be emptied.
Drain hose length . . . . . . . . . . . . 1.50 m
Maximum delivery head . . . . . . . 1.50 m
Maximum drain hose length . . . . 4.00 m
,If the on-site water drainage
system is not fitted with a non-return
valve or an appropriate air gap, one
must be fitted to prevent the risk of
back-flow. (See "Installation conditions
requiring a non-return valve").
^ Pull the hose off its connection (see
arrow).
^ Allow any residual water to run into
the container.
^ Unwind the hose and pull it carefully
out of the holders.
The following optional accessories are
available:
– an extension hose
– a non-return valve kit for connection
to an external condensed water
outlet (includes an extension hose).
Maximum delivery head with
non-return valve fitted: 1.00 m
Arranging the drain hose
,Do not pull on the drain hose and
do not stretch it or allow it to become
kinked as it could get damaged.
^ There will be a small amount of
residual water in the drain hose.
Have a container ready to collect this.
38
^ Position the hose to the right or left
hand side as necessary.
Leave the hose in the middle holder to
prevent it from becoming kinked
inadvertently.
Installation and connection
External drainage via a sink or gully
^ See "Front view" illustration.
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Example: Connection to a sink drain
outlet
The drain hose with non-return valve
fitted can be connected directly to a
suitable sink drain outlet.
^ Use the bow-shaped guide to
prevent the drain hose from
becoming kinked.
Installation conditions requiring a
non-return valve
,Certain installation conditions
require the fitting of a non-return
valve (available as an optional
accessory). A non-return valve will
prevent the risk of back-flow out of
the dryer which could cause
damage.
^ Remove the following from the back
of the dryer at the top:
Adapter 1 and hose clip 3 behind it.
A non-return valve is required:
– If the tumble dryer is connected to a
sink drain outlet (see the following
section).
– If the tumble dryer is connected to a
drainage system already in use by
another appliance, e.g. a dishwasher
or washing machine.
39
Installation and connection
^ Fit adapter 1 to the sink drain outlet
using nut 2.
If this nut has a flat disc in it you
should take the disc out first.
^ Attach the end of the hose 4 to
adapter 1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
,Non-return valve 5 has to be
fitted with the arrow pointing in the
direction of flow (i.e. towards the
sink). Otherwise water will not drain
out of the machine.
1 Adapter
2 Nut
3 Hose clip
4 End of the hose
5 Non-return valve
6 Tumble dryer drain hose
40
^ Fit non-return valve 5 to the tumble
dryer drain hose 6 (make sure it is
fitted in the correct direction (see
arrow on non-return valve).
^ Secure the non-return valve using
hose clips.
Installation and connection
Electrical connection
Important
This tumble dryer is supplied ready for
connection to an a.c. single phase
supply. The machine is supplied with a
mains cable with moulded plug.
The wires in the mains lead are
coloured in accordance with the
following code:
The accesibility of the plug must be
always ensured, in order to separate
the dryer from the mains.
The appliance should be connected up
only by a qualified electrician, in
accordance with national and local
safety regulations.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The voltage, rated load and plug rating
are given on the data plate. Please
ensure that these match the household
mains supply.
Green/yellow = earth
Blue = neutral
Brown = live
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth symbol
z or coloured green or green and
yellow.
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
The wire which is coloured brown must
be connected to the terminal which is
marked with the letter A or coloured
red.
WARNING
THIS APPLIANCE MUST BE
EARTHED
41
Consumption data
Programme
Load
Final spin speed
in a domestic washing machine
Energy
Duration
kg*
rpm
kWh
Minutes
Cottons
Normal
6.0
1000 (60 % residual moisture)**
1200
1400
1600
1800
3.35
3.05
2.90
2.75
2.50
104
95
91
88
80
Cottons
Hand iron
6.0
1000 (60 % residual moisture)**
1200
1400
1600
1800
2.70
2.40
2.25
2.15
1.85
85
76
71
68
60
Minimum iron Normal
3.0
1200 (40 % residual moisture)**
1.25
44
Minimum iron Hand iron
3.0
1200
1.00
39
Delicates Normal
2.0
800
1.40
97
Automatic Normal
3.5
800
2.10
96
Shirts Normal
2.0
600
1.25
84
Denim Normal
3.0
900
2.00
99
Woollens handcare
2.0
1000
0.15
4
Smoothing
3.0
1000
0.25
8
* Weight of dry laundry
** EN 61121:2005 test programme
All data without a "star" against it was calculated using EN 61121:2005.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme without selecting any
additional options.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any extra options selected.
42
Technical data
Height
850 mm
Width
595 mm
Depth
Depth with door open
634 mm
1074 mm
Suitable for pushing under a worktop
Suitable for stacking
Yes
Yes
Weight
Drum volume
52 kg
111 litres
Maximum capacity
Capacity of condensed water container
6 kg dry weight
approx. 3.5 litres
Drain hose length
Maximum delivery head
1.50 m
1.50 m
Maximum drain hose length
Length of connection cable
4.00 m
2.00 m
Voltage
Connected load
see data plate
see data plate
Plug rating
Lamp wattage
see data plate / plug
see data plate / plug
Energy consumption
see "Consumption data"
Test certificates awarded
Electrical safety, C-Tick Mark
Electrically suppressed
AS/NZS 1044
43
Programmable functions
for changing
standard settings
The programmable functions are
used to alter the machine's
electronics to suit changing
requirements.
Programmable functions can be
altered at any time.
44
Programmable functions
Extending the range of the
drying levels
You can extend the range of the
drying levels for many of the
programmes:
Machine iron+
(drier than Machine iron).
Hand iron+
(drier than Hand iron).
Normal+
(drier than Normal).
In addition the Extra dry drying level
can be made available for the
Delicates and Denim programmes.
You can use this programmable
function to extend the range of the
drying levels for the following
programmes:
Cottons, Minimum iron*, Delicates*,
Automatic, Denim.
* Machine iron+ is not available.
Follow steps A to E to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
– The Low temperature indicator light
will briefly flash on and off twice.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
1 Drying level range extended
(The Automatic indicator light will
also flash).
D Pressing the Start/Stop button
switches from one to the other.
E Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To select the extended drying level
^ Select a programme.
^ Press the drying level button
repeatedly until one or two indicator
lights come on.
– Indicator lights Extra dry and Normal
= Normal+
– Indicator lights Hand iron and
Normal = Hand iron+
– Indicator lights Machine iron and
Hand iron = Machine iron+
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
45
Programmable functions
Altering the volume of the
buzzer
The buzzer has two volumes.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Normal
The buzzer sounds at the end of a
programme (default setting).
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
Loud
The buzzer sounds at maximum volume
at the end of a programme.
C . . . and then release the Start/Stop
button.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
D Press the Low temperature button
once.
– The Low temperature indicator light
will briefly flash on and off four times.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Normal buzzer
(Default setting)
I Loud buzzer
(The Automatic indicator light will
also flash).
E Pressing the Start/Stop button
switches from one to the other. You
will hear the two buzzer volumes as
you do so.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
46
Programmable functions
Memory function
The electronics will memorise any
additional options selected for a
programme.
The duration selected for the Warm
air and Cool air programmes and the
Delay start period selected will also
be stored in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
twice.
– The Low temperature indicator light
will briefly flash on and off six times.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Memory deactivated
(Default setting).
I Memory activated
(The Automatic indicator light will
also flash).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
47
Programmable functions
Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.
The cooling down time
– can be extended by 5 minutes or 10
minutes.
– is not available for the following
programmes: Woollens handcare,
Smoothing, Warm air, Cool air.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
three times.
– The Low temperature indicator light
will briefly flash on and off seven
times.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
I The cooling down time will be five
minutes longer.
(The Automatic indicator light will
also flash once).
2 The cooling down time will be ten
minutes longer.
(The Automatic indicator light will
also flash twice).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
48
Programmable functions
Clean out airways indicator
,A clogged filter is a fire hazard!
The lint filter must be cleaned after
every program.
Fluff should be removed after drying.
The Clean out airways indicator will
remind you to clean the filters when a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.
You will have an idea of which of the
four options to select after a few drying
programmes.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
four times.
– The Low temperature indicator light
will flash on and off slowly once.
– P and 2 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 The Clean out airways indicator
light is deactivated
I The Clean out airways indicator
light will come on when there is a
heavy build-up of fluff
(The Automatic indicator light will
also flash once).
2 Default setting
(the Automatic indicator light will also
flash twice).
3 The Clean out airways indicator
light will come on when there is
only a light build-up of fluff
(The Automatic indicator light will
also flash three times).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
49
Programmable functions
Keypad tone
An audible tone sounds each time
you select a programme.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
five times.
– The Low temperature indicator light
will flash on and off slowly once and
will then flash on and off quickly
once.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Keypad tone deactivated
(Default setting)
I Keypad tone activated
(The Automatic indicator light will
also flash)
E Pressing the Start/Stop button
switches from one to the other.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
50
Programmable functions
Adjusting the dryer's
electronics for very soft water
,In some areas, water is
extremely soft which can affect the
sensitivity of the control electronics.
If the machine is installed in an area
with very soft water, you should
contact your local water supplier for
information and advice regarding
water hardness and water
conductivity. If the water
conductivity is less than 150 µS, the
following programmable function will
need to be activated.
Important. This programmable
function should not be activated if,
despite the water being extremely
soft (as would be the case if a water
softener were used), its conductivity
is greater than 150 µS.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button six
times.
– The Low temperature indicator light
will flash on and off slowly once and
will then flash on and off quickly
twice.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
I Adjusted for very soft water
(with low conductivity)
(The Automatic indicator light will
also flash)
E Pressing the Start/Stop button
switches from one to the other.
F Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
51
Alteration rights reserved/0110
M.-Nr. 06 605 540 / 04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement