electronic programmer for sliding gates. three

electronic programmer for sliding gates. three
GB
Drwg. No. 2442
B
1 2 3 4
DIP-SWITCH
1° CHANNEL
24 V OUTPUT
RADIO CONTROL
PLUG-IN CARD SUPPORT
TERMINALS FOR THE
CONNECTION OF THE
PUSH BUTTONS PULIN 3
26
27
28
OFF
ON
1
2
6
N.C. CONTACT. STOP
N.O. CONTACT. CLOSE
N.O. CONTACT. OPEN
COMMON. PUSH BUTTONS &
INDICATOR
LIMIT SWITCH. OPEN. N.C.
LIMIT SWITCH. COMMON
N.C. CONTACT.
PHOTOCELLS
ELECTRONIC PROGRAMMER
FOR SLIDING GATES.
THREE-PHASE AND SINGLE-PHASE
N.W.: THIS PANEL IS TESTED TO OPERATE GATES ONLY THROUGH
FADINI ACCESSORIES. NO GUARANTEE FOR ACCESSORIES OF
OTHER MAKE OR SPECIAL APPLICATIONS.
N. W.: for special applications, ie. to switch on lights - CCTV etc…,
SOLID STATE RELAYS are recommended to be used only.
Standard relays would affect the micro-processor.
Max. permitted load:
2 pairs photocells
1 radio receiver
- NO PRE-FLASHING/PRE-FLASHING
- AUTOMATIC/SEMI-AUTOMATIC
- REMOTE CONTROL: NO REVERSE TRAVEL/REVERSE
- PHOTOCELLS: STOP DURING OPEN/NO STOP DURING
OPEN-REVERSE DURING CLOSE
Should more pairs of photocells be required
than the recommended quantity, fit an auxiliary
transformer outside the control box.
RADIO CONTACT
24 Vac OUTPUT
THREE-PHASE
ELECTRIC
MOTOR
M
SINGLE-PHASE
ELECTRIC
MOTOR
M
5 A FUSE
HIGH
VOLTAGE
630 mA FUSE
LOGIC
SUPPLY VOLTAGE
230-400 V
THREE-PHASE
21 22 23
LIVE NEUTRAL
SUPPLY VOLTAGE
230 V SINGLE-PHASE
EARTH
CUT OFF SWITCH
BY COVER KNOB
630 mA FUSE
FLASHING LAMP
LINE
16 17 18 19 20 21 22 23
CLOSE
OPEN
230 V - 25 W max.
FLASHING LAMP
ALL OPERATIONS
OPEN, CLOSE & REVERSE
7
7
RADIO CONTACT. N.O.
5
MOTOR RUN
OPEN
+TIME
& CLOSE
+ DWELL TIME
PP
230 V
COMMON
3
9 10 11 12 13
8
LIMIT SWITCH. CLOSE. N.C.
4
–
–
24 V - 3 W max. INDICATOR
3
1 2 3 4 5 6 7 8
MICROPROCESSOR
PEDESTRIAN OPENING
CARD CONNECTOR
1 AMP.
FUSE: 24 V OUTPUT
TERMINALS 12 - 13
400 V
VOLTAGE
CHANGE-OVER SWITCH
10 CEI
SLIDING GATES – THREE-PHASE/SINGLE-PHASE
10 CEI
FEATURES OF THE ELECTRONIC PROGRAMMER FOR SLIDING GATES
All the electrical connections are to be made as per the following instructions and diagrams. Supply the terminals 21-22-23
with 230-400 V, 50 Hz, three-phase voltage. The “red led” No. 1 switches on and stays on as long as the board is properly
supplied. Set the timer “MOTOR RUN. OPEN & CLOSE” so that the running time of the motor is longer than the actual travel
of the gate. Set the timer “DWELL” - i.e. the interval between open and re-close - so that you can meet the required interval
of time.
LOGIC OF THE ELECTRONIC PROGRAMMER: When a pulse is given, the flashing light switches on. After three seconds
the motor starts. During the interval before re-closing, the light stays on. When the gate has fully re-closed, the light keeps
on flashing for three more seconds and then switches off automatically.
The 3 second interval (pre-flashing) which precedes the actual start of the motor can be eliminated by means of the DIPSWITCH “B” No. 4.
LED No. 1: It switches on when voltage is supplied.
LED No. 2: “PHOTOCELLS”. Normally on. It switches off when the photocells are obstructed.
LED No. 3: “OPEN”. It switches on when the respective switch is activated.
LED No. 4: “CLOSE”. It switches on when the respective switch is activated.
LED No. 5: “STOP” Normally on. It switches off when the respective switch is activated.
LED No. 6: “LIMIT SWITCH. CLOSE”. It switches off when the gate is fully closed.
LED No. 7: “LIMIT SWITCH. OPEN”. It switches off when the gate is fully open.
LED No. 8: “RADIO”. It switches on whenever a pulse is given, either through remote control, keyswitch or push buttons.
FUNCTIONS OF DIP-SWITCH “B”
DIP-SWITCH
B
12 3 4
ON
1 - ON: PHOTOCELLS. STOP DURING “OPEN” CYCLE
OFF: PHOTOCELLS. NO STOP DURING “OPEN” CYCLE
2 - ON: REMOTE CONTROL. NO REVERSE TRAVEL
OFF: REMOTE CONTROL. REVERSE TRAVEL
OFF
3 - ON: AUTOMATIC RE-CLOSING
OFF: NO AUTOMATIC RE-CLOSING
4 - ON: NO PRE-FLASHING
OFF: PRE-FLASHING
1)It is advisable not to expose the control box directly to weather conditions. If mounted outside, a suitable enclosure is
recommended to protect it from sunshine and rain.
2)Earth the equipment by using the terminal fitted to the box, bottom right-hand side.
3)Bridge terminals 1 - 2 if you do not require any photocells.
4)Should two sets of photocells be required, these are to be series connected to terminals 1 - 2, contact normally closed.
5)Bridge terminals 3 - 6 if you do not require any keyswitch or push buttons.
6)Fit the mains to the control box with a high sensitivity, differential, magnetic-thermal switch, 0.03 Amps.
7)NOTE WELL
FAULT FINDING:
- Check supply voltage with a tester: it must be 230-400 V, three-phase.
- Check the high voltage fuses.
- Check if the photocell contacts are normally closed.
- Check voltage from the control box to the electric motor: power might have dropped.
- Check the fuse LOGIC.
- The section of the electric cables to the motor must not be less than 1.5 mm2.
- To allow a sliding gate to open partially for pedestrians, pulse the N.O. push button that is connected to the respective
terminals on the pedestrian opening card. Adjust the span of the pedestrian opening through the provided potentiometer
“P” to meet the site requirements. DIP - switch - B - N° 3 set to “ON” automatic mode: the gate runs to closed after the time
set with the main PC board potentiometer, ie. (+ DWELL). - You can manually pulse to close either by push button or remote
control.
OPTIONAL PEDESTRIAN
* 24 V ~ output. Terminals 12-13. It can supply power for 2 pairs of photocells plus 1 radio receiver.
OPENING P.P. CARD TO FIT
THE P.P. CONNECTOR
Terminal 11 provides a power output for a lamp. 24 V - 3 W max.
Flashing lamp output. Terminals 22-23. Maximum available power 25 W max.
PP
CONNECTOR FOR THE
PEDESTRIAN OPENING CARD
Via Mantova, 177/A - 37053 Cerea (Verona) Italy
GB
Drwg. No. 2442
®
s.n.c.
AUTOMATIC GATE MANUFACTURERS
Tel. 0442 330422 r.a. - Fax 0442 331054
®
e-mail: [email protected] - www.fadini.net
the gate opener
Made in Italy
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement