SPOT 360 – 60 RGB

SPOT 360 – 60 RGB
SPOT 360 – 60 RGB
 Please read the manual before installing and using this lighting
Keep it for future reference
Content
INSTRUCTION............................................................................................................... 3
SAFETY INSTRUCTION.............................................................................................. 3
SIZE................................................................................................................................. 4
DMX CHANNEL.......................................................................................................... 10
16CH(DEFAULT) ..................................................................................................... 10
13CH.......................................................................................................................... 12
8CH............................................................................................................................ 13
6CH............................................................................................................................ 13
MENU............................................................................................................................ 14
MENU NEVIGATION...................................................................................................14
1.
DMX MENU...................................................................................................... 14
2.
Manual Dimmer menu.............................................................................. 15
Demo menu..................................................................................................16
Macro menu................................................................................................. 16
Test Menu..................................................................................................... 17
Set Menu....................................................................................................... 17
3.
4.
5.
6.
TECHNICAL PARAMETER....................................................................................... 19
EQUIPMENT CLEANING..........................................................................................20
2
Instruction
Thank you for using our products! Please check the equipment carefully
before using. Any damage or needs, please kindly let us know.
This product complies with the following standards:
GB7000.1-2007/IEC60598-1:2003
GB7000.217-2008/IEC60598-2-17:1984+A2:1990
Safety Instruction
Every person involved with the installation, operation and maintenance of this
device has to be qualified and follow the instructions of this manual. Manufacturer
will not with responsibility for those operations nots according to this Instruction

Verify that the voltage matches the rated voltage.

Before using the fixture, check that all power distribution equipment and
cables are in perfect condition and rated for the current requirements of all
connected devices.

Always ground (earth) the fixture electrically.

Avoiding hit the Light when you are move or install the light.

The minimum distance between light-output and the illuminated surface
must be more than 0.5 meters. Keep all combustible materials (for example
fabric, wood, paper) at least 0.2 meters away from the fixture.

Do not expose the fixture to rain or moisture.

Avoid looking directly into the light source (especially those who suffer from
epileptic fits)

Maximum ambient temperature (Ta) is 40°C.

The Maximum surface temperature is 60°C

When suspending the fixture above ground level, verify that the structure
can hold at least 10 times the weight of all installed devices.
3

Don’t move the cord directly. It’s only allowed with the handle.
 Verify that all external covers and rigging hardware are securely fastened
and use an approved means of secondary attachment such as a safety
cable.
Size
Size: mm
ESC/MENU
UP
DOWN
enter the main menu, or exit the current menu (i.e. return to
the upper menu& give up the selected item or parameter).
Browse the menu item forward or increase the parameter.
Browse the menu item backward or decrease the
parameter.
4
Confirm the selected item or parameter (i.e. enter the next
ENTER
menu, or escape the current menu and save the selected
item or parameter)
DISPLAY
Display Menu
Common operation
 Manual dimmer
Power on, the lighting shows A001
Press UP or DOWN buttons to browse to manual dimmer,
Press ENTER to menu,
Press UP or DOWN buttons to browse to the flowing menu
Light Red: Red dimming
Light Green: Green dimming
Light Blue: Blue dimming
Light White: White dimming
Scan Pan: Pan movement
Scan Tilt: Tilt movement
Scan Pan Fine: Pan fine
Scan Tilt Fine: Tilt fine
Light Strobe: Strobe brightness adjust
Color wheel: color wheel adjusts
If you want to adjust one of above items, press ENTER to enter
and adjust by pressing UP and DOWN buttons, then press ENTER
to confirm
5
 Creating static colors
After Power on shows A001, press UP or DOWN buttons to Demo
menu, the lighting will create static colors:
RED (red)
GEN (green))
BLU (blue)
CYN (cyan)
PUR (purple)
PWHI (pure white)
AWHI (all white)
 Run built-in programs
Power on shows A001, press UP or DOWN buttons to Demo Menu,
the lighting will run the built-in programs
CHCL (color change program)
TWINKLING (strobe program)
FADE (fade program)
 Setting DMX channel modes
There a r e 4 d m x c h a n n e l m o d e s : 16/13/8/6ch,
f o l l o w i n g i s instruction to set dmx channel modes:
DMX menu---Enter
UP/down----DMX channels
6
ENTER---up/down----stage mode
Enter---up/down---16 Channels
13 Channels
8 Channels
6 Channels
 Run programmable macro
Power on, press UP or DOWN buttons to browse to MACR, the
lighting will run macro, press ENTER to enter can browse to the
below menus:
Up/down----Macro Menu
Enter---up/down (to browse below menus:
Set quantity: to set how many built in program in the macro (how
many programs you set, there will be how many steps to choose the
menu)
ST01:1st program set step menu
ST02:2nd program set step menu
``````
If you need to adjust one of the parameter, press ENTER to set.
There are 3 options in every step menu:
CHCL (color change program)
7
STROBE (strobe program)
FADE (fade program)
Eg:
STOB
Set steps number to 3
ST01 choose the STOB program
CHCL
ST02 choose the CHCL program
ST03 choose the FADE program
FADE
The flow chart as right figure.
 Stand-alone mode
In Stand-alone mode, the lighting out of control of any exterior
signal, run solely. Setting method is:
Press MODE-button until shows SET(set menu)
Press ENTER-button
Press UP or DOWN-button to browse to MAAL
Press ENTER-button
Press UP or DOWN-button to browse to ALON (alone)
Press ENTER-button to confirm .
 Master/slave mode
Set one lighting to master-device,and others to slave-device,so all
lightings run synchronously follow the master-device .
1. Setting Master-device
8
Press MODE-button until shows SET(set menu)
Press ENTER-button
Press UP or DOWN-button to browse to MAAL
Press ENTER-button
Press UP or DOWN-button to browse to MAST(master)
Press ENTER-button to confirm .
2. Slave-device setting
Press the lighting to DMX mode position.
 DMX mode
In DMX mode, the lighting can have controlled by controller. When
the display shows A001 or the other actual stored addresses. the
lighting is in DMX mode.
 Setting DMX start address
In DMX mode, a fixture requiring one or more channels for control
begins to read the data on the channel indicated by the start
address. For example, a fixture that uses 3 DMX channels and
was addressed to start on DMX channel 1, would read data from
channels: 1, 2, 3. Choose start addresses so that the channels used
do not overlap, and note the start address selected for future
reference. Note that assign the same address to the different
lightings, they will receive the same signal.
Setting DMX address method:
9
When the lighting is in DMX mode, it shows A001( the stored
address),
Press ENTER , shows DMX(DMX menu)
Press ENTER
Press UP or DOWN to set DMX address
Press ENTER to confirm
 Reload manufacturer's Data
Press SET-button until displays SET(Set menu)
Press ENTER
Press UP or DOWN to browse to LOAD
Press ENTER
Press UP or DOWN to browse to ON(reload)/OFF (do not reload)
Press ENTER to confirm .
DMX Channel
There are 4 dmx channel modes: 16/13/8/6ch, 16ch is default
channel.
Channel
1
2
3
4
5
DXM Value
000-255
000-255
000-255
000-255
000-255
Function
Strobe
Dimming
Tilt scan
Tilt fine
Pan scan
10
6
7
8
9
000-255
0-127
128-189
190-193
194-255
0-127
128-189
190-193
194-255
000-255
11
12
13
14
15
0-4
10-14
60-64
70-74
110-114
120-124
130-134
135-139
250-255
000-255
000-255
000-255
000-255
000-255
16
000-255
10
Pan fine
Tilt unlimited rotation
Null
Positive rotation
Null
Reverse rotation
Pan unlimited rotation
Null
positive rotation
Null
Reverse rotation
Scan speed
Fan, reset function, angle
setting
540°
Reset fixture
Fan speed
Fan Auto
Fast dimmer
Smooth dimmer
540°
630°
Back light on
Color wheel
Red dimmer
Green dimmer
Blue dimmer
White dimmer
CTC Temperature color
control
11
13 Channel
Channel
1
DXM Value
000-255
Function
Strobe
2
000-255
Dimming
3
000-255
4
000-255
5
000-255
6
000-255
194-255
Tilt scan
Tilt fine
Pan scan
Pan fine
Tilt unlimited rotation
Null
Positive rotation
Null
Reverse rotation
000-255
Pan unlimited rotation
0-127
Null
Positive rotation
Positive rotation
Scan speed (fast → slow)
0-127
7
128-189
190-193
8
128-189
190-255
9
000-255
10
000-255
11
000-255
12
000-255
13
000-255
)
Red dimmer
Green dimmer
Blue dimmer
White dimmer
12
8 Channel
Channel
DXM Value
Function
1
000-255
2
000-255
3
000-255
4
000-255
5
000-255
6
000-255
7
000-255
8
000-255
Tilt scan
Tilt fine
Pan scan
Pan fine
Red dimmer
Green dimmer
Blue dimmer
White dimmer
Channel
DXM Value
Function
1
000-255
Dimming
2
000-255
Strobe
3
000-255
Tilt
4
000-255
Pan
5
000-255
Color wheel
6
000-255
Fan, reset function, angle setting
6 Channel
13
Menu
1.
DMX Menu
2.
Manual Dimmer
Demo Menu
3.
4.
Macro Menu
5.
Test Menu
AXXX
AXXX
DMX address
Setting
Set Menu
6.
1. DMX menu
Main menu
Menu
Options
Options
DMX
Address
001-510
DMX address setting
No
Signal
DMX
DMX Menu
Stop Run
Hold Run
Auto Run
Sound Run
DMX
Channels
16 Channels
STAG Mode
13 Channels
8 Channels
6 Channels
14
2. Manual Dimmer menu
Main menu
Manual
Dimmer
Menu
Options
Light Red
000-255
Light Green
000-255
Light Blue
000-255
Light White
000-255
Scan Pan
128
Scan Tilt
128
Scan Pan Fine
000-255
Scan Tilt Fine
000-255
Light Strobe
000-255
Color wheel
000-255
Light Calibrate
15
Options
Cal Red
0~-99
Cal Green
0~-99
Cal Blue
0~-99
Cal Pan
128~+127
Cal Tilt
128~+127
3. Demo menu
Main menu
Demo menu
Menu
Options
Red
000-255
Green
000-255
Blue
000-255
Yellow
000-255
Cyan
000-255
Purple
000-255
Pure White
000-255
All White
000-255
Chang Color
000-255
Twinkling
000-255
Fade
000-255
4. Macro menu
Main menu
Menu
Options
Step Quantity:62
Program Step 01
Macro
menu
Change Color
Twinkling
Fade
.......
.......
Change Color
Program Step 62
Twinkling
Fade
16
5. Test menu
Main menu
Menu
Options
Test All
Test: OFF
Test: ON
Test menu
Test: OFF
Test LED
Test: ON
Test: OFF
Test P&T
Test: ON
6. SET menu
Main
menu
Menu
Options
Options
Reset
Machine
Load
parameter
Master /
Alone
Auto
/
Sound
MIC sense
Reset: ON
Reset: OFF
Load ON
Load OFF
Master mode
Alone mode
Auto Mode
Sound Mode
00~99%
Set menu
TC switch
Options
TC Switch Mask
TC Switch Temp
17
Switch Mask ON
Switch Mask OFF
TC Temp Cap
TC T e m p
Cap: Yes
TC T e m p
Cap: No
TC Temp Set
Reverse Pan
Reverse
Pan :ON
Reverse
Pan: OFF
Reverse Tilt
Scan
setting
Scan 16 Bit
Scan Black Out
Reverse Tilt: ON
Reverse Tilt: OFF
Scan 16 Bit: ON
Scan 16 Bit: OFF
Scan Black Out:
ON
Scan Black Out:
OFF
Feed Back
Feed Back: ON
Feed Back: OFF
Dimmer
curve
Dimmer
speed
Square Law
Dimmer: Smooth
Dimmer: Fast
Time: tt/mm/ss
Information
Date: mm/dd/yy
Model: LM-XXXX
Use
Time: hour:
minute
18
Time: hour: minute
Technical parameters
Rated voltage
AC100-240V , 50/60Hz
Rated power
80W
Led
Color
1PCS 60W LED
R、G、B、W
Displace screen
LED life span
Blue LCD1602
50,000 hours
Strobe
1-25 Hz
Dimmer
0-100%
DMX channel
16/13/8/6
Control mode
Master/slave 、 DMX mode 、 Manual mode 、 Sound
active
Housing
ABS plastic
Temperature
-25℃-40℃
IP rating
IP20
Dimension
L242*W139*H308mm
Weight
3.8kg
Equipment Cleaning
* Humidity, smoke or dirty environments can easily make the lens cover with dirt.
To make sure the best light effect, lens need frequent cleaning.
* Lens need cleaning with soft cloth and special abrasive cleaners and keep dry.
* Lens need cleaning every 30 days.
19
For more information please visit
www.kudux.com
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement