remote power supply bps-1002
REMOTE POWER SUPPLY
BPS-1002
Features
•
•
•
•
•
•
•
•
•
•
•
Description
Mircom’s BPS-1002 is an extremely cost effective 10
amp voltage regulated remote power supply/battery
charger. It may be connected to any 12 or 24 volt Fire
Alarm Control Panel (FACP). Primary applications
include Notification Appliance Circuit (NAC such as
strobes and horns) expansion support to meet ADA
requirements. It also provides auxiliary power to support
system accessories. The unit delivers regulated and
filtered 24 volt power to Class B or Class A NAC loop
circuits.
Additionally, a separate 1.0A auxiliary output with reset
for four (4)-wire smoke detectors is available. The 10
amp max. alarm current can be divided between the
four (4) outputs for powering NAC devices. Each output
is rated at 2.5 amp max., and can be independently
programmed for Steady, Temporal Code 3 or Strobe
Synchronization. All outputs may be programmed for
Input to Output Follower Mode (output will follow input.
i.e. March Time Input, March Time Output). An individual
output of 4 amp is achieved by paralleling 2 outputs.
The BPS-1002 in non-alarm condition provides
independent loop supervision for Class A and/or Class
B FACP NAC circuits. In the event of a loop trouble, the
FACP will be notified via the steered input (input 1 or
input 2). In addition, there are common trouble output
terminals (N.C., C, N.O.) which are used to indicate
general loop/system trouble. A common trouble input
is provided for optional NC (normally closed) devices
to report trouble to the FACP. Two (2) FACP signaling
outputs can be employed and directed to control
supervision and power delivery to any combination of
the four (4) outputs. The unit also features “Loop Output”
trouble memory indication to help identify trouble some
sporatic problems.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Power input 115VAC 60 Hz, 4.4 amp.
Two (2) Class A or two (2) Class B FACP inputs
Field selectable 24VDC or 12VDC voltage regulated
power limited outputs
Two (2) NC dry contact trigger inputs
24VDC @10 amp max total alarm current
2.5 amp max current per output
Separate 1 Amp auxiliary output with built-in and
remote reset capability
Two (2) outputs may be paralleled for more power
on an indicating circuit
Programmable supervised indicating circuit outputs:
Up to Four (4) Class B or Two (2) Class A or One (1)
Class A and Two (2) Class BThermal and short circuit
protection with auto reset
Built-in charger for sealed lead acid or gel type
batteries
Automatic switchover to stand-by battery when AC Fails
Zero voltage drop when switching over to battery backup
PTC battery protection
AC fail supervision (form “C” contact, 1 amp /
28VDC). Factory set for 1 minute with optional 18
hour delay setting (field selectable)
Battery presence and low battery supervision (form
“C” contact, 1 amp / 28VDC)
Input and output status LED indicators
2 wire horn/strobe Sync mode allows audible
notification appliances (horns) to be silenced while
visual notification appliances (strobes) continue to
operate
Temporal Code 3, Steady Mode, Input to Output
Follower Mode (maintains synchronization of
notification appliances circuit)
Horn/Strobe sync protocols include Mircom, Amseco,
Gentex, System Sensor, Faraday and Wheelock
March Time
Compatible with 12 or 24VDC fire panels.
Filtered and electronically regulated output
Output loop supervision steered to input 1 or input 2
Common trouble input and output
Ground fault detection
Unit includes power supply, red enclosure, cam lock,
open frame transformer and battery leads
NOT TO BE USED FOR INSTALLATION PURPOSES.
MEA
approved
S5434
7315-1477:146
385-05-E
CATALOG NUMBER
5667
Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models.
Power Supply Specifications
AC Input
115VAC / 4.4 amp @ 60Hz
Output
24VDC. Maximum 2.5 amp per output
Total of 10 amp in Alarm Condition
Battery
For 12VDC operation use a 12VDC / 12AH battery
For 24VDC operation use two (2) 12VDC / 12AH or two (2) 12VDC / 7AH batteries connected in series
Stand-by/Alarm Current:
90mA/175mA
EOL Resistor (end of line)
2.2K (2200 ohm)
Standby Specifications
Standby Batteries
Standby Time
Alarm Output Total Amp/Minutes
Aux Output Current
24VDC/12AH
(use two (2) 12VDC batteries in series)
24 Hours
10 amp/15 Minutes
50mA
60 Hours
10 amp/5 Minutes
-
24VDC/7AH
24 Hours
10 amp/5 Minutes
-
24VDC/36AH Battery
24 Hours
10 amp/15 Minutes
1 amp
12VDC/36AH Battery
24 Hours
10 amp/15 Minutes
1 amp
Enclosure Dimensions
2.25"
15.5”H x 12”W x 4.5”D
12"
3.68"
4.56"
1.22"
1.22"
4.5"
.875"
1.22"
1.3"
9.97"
1"
1"
2"
6.625"
13.25"
13.53"
3.5"
2.2"
1.25"
15.5"
1"
1.22"
2.25"
3.68"
4.56"
Ordering Information
Model
Description
BPS-1002
10 Amp Remote Power Supply
NOT TO BE USED FOR INSTALLATION PURPOSES.
Distributed by:
Canada
25 Interchange Way
Vaughan, Ontario L4K 5W3
Telephone: (905) 660-4655
Fax: (905) 660-4113
U.S.A.
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Toll Free: (888) 660-4655
Fax Toll Free: (888) 660-4113
Web page: http://www.mircom.com
Email: [email protected]
ISO 9001:2000
REGISTERED
CAT. 5667
Rev. 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement