Feature Specification Function Menu Structure How to

Feature Specification Function Menu Structure How to
Feature
1
2
Dimension
■ 1/3" 1.3M SONY Progressive Scan Color CMOS Sensor
■ 1280H (720P-AHD)
■ 3DNR(Smart NR)/D-WDR
■ OSD, Sense-up x 30
■ 40-IRLED
Specification
Item
Specification
1/3" 1.3Megapixel CMOS
Imaging Sensor
Progressive Scan
Scanning System
Number of effective pixels
1305(H) X 1049(V) = 1,368,945(pixel)
Total number of pixels
1312(H) X 1069(V) = 1,402,528(pixel)
More than 50㏈
S/N Ratio
Video Output Mode
720P (1280 X 720) 25P/30P
1000TVL NTSC/PAL
Video Output Level
AHD1.0
1.0 Vp-p (75Ω, Composite)
Lens
Built-in DC Iris ICR Vari-focal Lens (2.8~12mm, F=1.4)
Setup and Function
1.0Lux(Color) , 0.5Lux(BW) , 0.02Lux(Sens-up x30)
Min. Illumination
Built-in
O.S.D
FUNCTION SET UP BUTTON
AUTO / FLK
Electronic Shutter Speed
NTSC : 1/30(60)sec ~ 1/50,000sec
PAL : 1/25(50)sec ~ 1/50,000sec
1 ~ 15 Step
AGC
Sens-up
AUTO / OFF (x2 ~ x30)
D-WDR
ON / OFF / AUTO
OFF / AUTO
DEFOG
BLC / HSBLC / OFF
Backlight Compensation
ATW / AWC-SET / INDOOR / OUTDOOR / MANUAL / AWB
White Balance
AUTO / COLOR / BW / EXT
Day & Night
2DNR / 3DNR
DNR
VBS-EXTERNAL
FREEZE / MIRROR / NEG.IMAGE
D - EFFECT
On / Off (4 Zone Selectable)
Motion Detection
▶ VBS-EXTERNAL
On / Off (4 Zone Selectable)
Privacy Masking
- Video signals are output through this RCA type Port. Connect this port(VBS-External)
English / Chinese1 / Chinese2 / German / French / Italian / Spanish /
Polish / Russian / Portuguese / Dutch / Turkish / Korean / Japanese / Hebrew / Arab
Language
to the Video IN port of a monitor
▶ FUNCTION SET UP BUTTON
LIVE DPC / WHITE DPC / BLACK DPC
Defect
- SET Button : Displays the menu on the screen. Press the button to confirm status or after changing a selected item.
Pelco - D / P
Protocol
- Up and Down Button : Used to move the cursor up or down in the menu screen to select a desired menu item.
RS - 485[ Baud Rate : 2400,4800,9600,19200,38400 ]
Communication [OPTION]
- Left and Right Button : Used to move the cursor left or right in the menu screen or to
SHARPNESS / MONITOR / LSC / NTSC/PAL
Adjust
change the value of the selected item.
AC24V & DC12V
Supplied Voltage
IRLED OFF : 100mA(Max), IRLED ON : 230mA(Max)
Power Consumption
3
Function Menu Structure
4
Notes
Function Menu
■ DC
■ MANUAL
■ SHUTTER
■ AGC
■ D-WDR
■ DEFOG
■ OFF
■ BLC
■ HSBLC
■ ATW
■ AWC→SET
■ INDOOR
■ OUTDOOR
■ MANUAL
■ AWB
DAY & NIGHT
■ AUTO
■ COLOR
■ B/W
■ EXT
NR
■ 2DNR
■ 3DNR
■ CAM TITLE
■ D-EFFECT
■ MOTION
■ PRIVACY
■ LANGUAGE
■ DEFECT
■ RS485
■ SHARPNESS
■ MONITOR
■ LSC
■ MONITOR OUT
■ COMET
■ SAVE&END
■ RESET
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
SPECIAL
ADJUST
EXIT
■ SENS-UP
■ BRIGHTNESS
This function Deactivates when the AGC "OFF", DAY&NIGHT "OFF"
OFF : Deactivates the Sense-up function.
AUTO : You can adjust brightness by increasing or decreasing the shutter speed
- Speed : x2 ~ x30
* Note that the higher the zoom level, the brighter the screen, but the more likely it
is that an after-image will appear.
* Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom
level is increased, this is normal.
▶ BRIGHTNESS : You can control the brightness by using the Left and Right button in Manual Lens mode.
▶ D-WDR : If there are bright area and dark area on the screen at the same time,
this function makes both areas to be in clear image
■ VIDEO.OUT
* SET : OFF/ON/AUTO
■ NOT SAVE
D-WDR ON
How to use the camera
D-WDR OFF
▶ DEFOG : Carry out defog function
Notes
⊙ An item with the
, you can move to sub menu pressing SET button
⊙ An item with the - - -, icon is unavailable due to function settings.
BACKLIGHT
▶ BLC : This function allows you to get a clear pictures of objects even the objects in strong backlight.
- BLC : Enables a user to directly select a desired area from a picture, and to view the area more clearly.
LENS
- LEVEL : LOW, MIDDLE, HIGH
● Using this function, you can control screen brightness
- AREA : Area Set(Size & Position)
1. When the SETUP menu screen is displayed, select 'LENS' by using the Up and
Down buttons so that the arrow indicates 'LENS'.
2. Select the connected type by using Left and Right buttons
- DEFAULT : Factory reset
▶ HSBLC : If the scene contains extremely bright light areas such as;
from street light or car headlight, the light can mask out much of the on-screen detail.
▶ DC : Select Auto Iris Lens (MODE: INDOOR / OUTDOOR)
▶ MANUAL : Select Manual Lens
EXPOSURE
1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Up and
Down buttons so that the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Up and Down buttons.
▶ SHUTTER : Auto / FLK / Manual
HSBLC OFF
※ Out Door : Auto
- DISPLAY : SELECT AREA ON/OFF
※ In door : NTSC : 1/30(60), PAL : 1/25(50)
- BLACK MASK : Mask ON/OFF
- AUTO : Select this mode to control the shutter speed automatically.
Shutter speed is automatically controlled depending on the brightness of the screen.
- FLK : Select this when you experience picture flicker
HSBLC ON
- SELECT : AREA1, AREA2, AREA3, AREA4
- LEVEL : Masking Level Set
- MODE : ALL DAY and NIGHT
- DEFAULT : Factory reset
- MANUAL : LEVEL (x2~x30 ~ 1/50,60~50000)
▶ AGC : LEVEL 1 ~ 15
The higher the gain level, the brighter the screen but the higher the noise.
▶ SENSE-UP : When it is night of dark, the camera automatically detects the light level and maintains a clear pictur.
※ DISPLAY - AREA Set
- Use Narow Button to set
Size and Position
WHITE BALANCE (WHITE BAL)
5
1. When SETUP menu screen is displayed, select 'WHITE BAL' by using Up and
SPECIAL
Down buttons so that the arrow indicates 'WHITE BAL'.
Down buttons so that the arrow indicates 'SPECIAL'.
2. Select the connected type by using Left and Right buttons
2. Select a desired mode using the Up and Down buttons.
※ Select one of the following 6 modes, as appropriate for your purpose
▶ CAM TITLE : If you enter a title, the title will be appear on the monitor.
▶ ATW : Select this when the color temperature is between 2,500ºK and 9,800ºK.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow indicates 'CAM TITLE'
▶ AWC→ SET : To find the optimal setting for the current luminance environment in this
Notes
mode, set the point the camera towards a sheet of white paper and press
⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if you
enter one.
the SET button. If the environment changes, readjust it.
▶ INDOOR
6
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using Up and
② Set it to 'On' by using Left and Right buttons.
: Select this when the color temperature is around 3,100ºK.
▶ OUTDOOR : Select this when the color temperature is around 5,100ºK.
③ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
▶ MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
the ATW or AWC mode. After that switch to MANUAL mode.
Notes
Adjust the [BLUE] and [RED], according to the changing of color on the screen
⊙ If you entered wrong letter……
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over the
letter to be edited, move the cursor to the letter to be inserted and then press SET button.
▶ AWB : Select this when the color temperature is between 2,400ºK and 11,000ºK.
Notes
⊙ White balance may not work properly under the following conditions.
In this case, select the AWC mode.
① When color temperature of environment surrounding the subject is out of the control range
② If the camera towards a fluorescent, the White Balance operation may become unstable
④ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
on the screen. Select the position to display the title on the screen by using the 4 directoin
buttons and press the SET button. When the position is determined, select 'END' and press
the SET button to return to the SPECIAL menu.
DAY&NIGHT
● You can display pictures in Color or Black and White.
▶ D-EFFECT
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' by using the Up and
* Freeze : You can stop the image or reactivate it.
Down buttons so that the arrow indicates 'DAY/NIGHT'
* MIRROR
2. Select the connected type by using Left and Right buttons
- Mirror : you can flip the image vertically on the screen.
▶ AUTO : The mode is switched to color in a normal environment, but switches to B/W mode
- V-Flip : you can flip the image vertically and horizontally both.
when ambient illumination is low. To set up the day&night switching delay time for AUTO mode, press the SET button
also you can select the duration time about changing the D(Day) → N(Night) and N(Night) → D(Day) mode.
- Rotate : you can flip the imate horizontally on the screen.
* NEG IMAGE : you can flip the color on screen.
- Delay : You can select the duration time about changing the day/night mode.
▶ MOTION : If you connect an alarm device to this camera, you can monitor activity
- D→N(AGC) : The condition about changing color to B/W mode.
( Increase the level, switches to B/W slowly )
because a signal is generated by the camera whenever motion is detected. The
motion detection signal is output through the MD OUT port.
- N→D(AGC) : The condition about changing color to COLOR mode.
( Increase the level, switches to Color fast )
- SELECT : AREA1, AREA2, AREA3, AREA4
→ The brightness of illumination is changeable by installed environment.
- DISPLAY : SELECT AREA ON/OFF
▶ COLOR : The picture is always displayed in color.
Use Narow Button to set Size and Position
▶ BW : The picture is always displayed in B/W.
▶ EXT : This mode allows you to apply a desired filter to external signals.
NR
● This function reduces the background noise in a low luminance environment
1. When the SETUP menu screen is displayed, select 'NR' by using the Up and
Down buttons so that the arrow indicates 'NR'.
- SENSITIVITY : When sensitivity number is high, motion detection sensitivity is increased to recognize
2. Select a desired mode using the Up and Down buttons.
even small movement
▶ 2DNR - LEVEL : OFF/LOW/MIDDLE/HIGH
- COLOR : SELECT COLOR (GREEN / BLUE / WHITE / RED)
▶ 3DNR - LEVEL : OFF/LOW/MIDDLE/HIGH
- TRANS : 1.00 ~ 0.00
* Activates NR so that noise is reduced.
- ALARM (VIEW TYPE, OSD VIEW, ALARM OUT, TIME)
3. Set the NR mode to 'ON' andpress the SET button. Then you can adjust the Noise reduction level.
▶ PRIVACY : Hide an area you want to hide on the screen.
- DEFAULT : Factory Reset
7
▶ SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer
- SELECT : AREA1, AREA2, AREA3, AREA4
- DISPLAY : SELECT AREA ON/OFF, SET Size and Position
Adjust this value appropriately depending on the sharpness of the picture.
- SET : LEVEL, START AGC, END AGC
▶ MONITOR
* COLOR / OFF / MOSAIC / INV.
Use Narow Button to set Size and Position
* CRT : CRT Monitor
* LCD : LCD Monitor
- Set : BLACK LEVEL, GAMMA, BLUE GAIN, RED GAIN
▶ LSC : Lens shading compensation
▶ VIDEO. OUT
* NTSC/PAL : Select NTSC / PAL
- COLOR : SELECT COLOR (WHITE / BLACK / RED / BLUE / YELLOW / GREEN / CYAN / USER)
▶ MONITOR OUT : 4:3 / 16:9
▶ COMET : ON/OFF
- TRANS : 1.00 ~ 0.00
- DEFAULT : Factory Reset
EXIT
▶ LANGUAGE : You can select the menu language according to your requirement.
- Supplied Language : English, Chinese1, Chinese2, German, French, Italian,
Spanish, Polish, Russian, Portuguese, Dutch, Turkish
1. When the SETUP menu screen is displayed, select 'EXIT' by using Up and
Down buttons so that arrow indicates 'EXIT'.
2. Select the connected type by using Left and Right buttons
▶ DEFECT
▶ SAVE&END
* Defect CMOS correction to compensate for defects that can occur at the low light conditions.
▶ RESET : Resets the camera settings to the factory defaults.
* LIVE DPC : Auto Defect
- AGC LEVEL : 0 ~ 255
Language and Communication status is not initialized
▶ NOT SAVE
- LEVEL : Level of Auto Defect (0 ~ 100)
* WHITE / BLACK DPC : Manual Defect
- POS / SIZE : SET Size and Position
- START : Start Defect
(Close the lens to shield the light, Select the START and press the SET button twice)
- DPC VIEW : ON/OFF
- LEVEL : Manual Defect Value (0 ~ 100)
- AGC : 0 ~ 14
- SENS-UP : Defect Sens up Value (x2 ~ x30)
▶ RS485 : This function sets up the camera communication status when controlling the camera through an
external device.
* You can control SETUP Menu through this port by using external controllers like a remote
controller that RS-485 Communication is supported
- SET : CAM ID, ID DISPLAY, BAUDRATE
ADJUST
1. When the SETUP menu screen is displayed, select 'ADJUST' by using Up and
Down buttons so that arrow indicates 'ADJUST'.
2. Select a desired mode using the Up and Down buttons.
MEMO
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement