Installation Manual for the
Installation Manual for the
SINGLE Gate Operator System
FOR PROFESSIONAL INSTALLATION ONLY!
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the installer
and user accept full responsibility for following and noting the installation and
safety instructions. Failure to follow installation and safety instructions can result
in hazards developing due to improper assembly. You agree to properly install this
product and that if you fail to do so GTO, Inc. shall in no event be liable for direct,
indirect, incidental, special or consequential damages or loss of profits whether
based in contract tort or any other legal theory during the course of the warranty
or at any time thereafter. The installer and/or user agree to assume responsibility
for all liability and use of this product releasing GTO, Inc. from any and all
liability. If you are not in agreement with this disclaimer or do not feel capable
of properly following all installation and safety instructions you may return this
product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before
attempting to install and use this automatic gate operator. This gate operator
produces a high level of force. Stay clear of the unit while it is operating and
exercise caution at all times.
All automatic gate operators are intended for use on vehicular gates only.
2007 GTO, Inc.
©
rev - 09/13/07
For more information on GTO/PRO’s full line of automatic gate openers and access controls visit our website at www.gtopro.com
R4000XL INST
This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety,
as established and made effective March 1, 2000, by Underwriters Laboratories Inc.
The GTO/PRO® 4000XL Gate Operator is intended for use with vehicular swing gates. The operator can be used in
Class I, Class II, Class III and Class IV applications. Vehicular gate operator class categories
Residential Vehicular Gate Operator-Class I: A vehicular gate operator (or system) intended for use in a home
of one-to-four single family dwelling, or a garage or parking area associated therewith.
Commercial/General Access Vehicular Gate Operator-Class II: A vehicular gate operator (or system) intended
for use in a commercial location or building such as a multifamily housing unit (five or more single family units),
hotel, garages, retail store, or other building servicing the general public.
Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended
for use in an industrial location or building such as a factory or loading dock area or other locations not intended to
service the general public.
Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use
in a guarded industrial location or building such as an airport security area or other restricted access locations not
servicing the general public, in which unauthorized access is prevented via supervision by security personnel.
Conversion Chart
Converting Metric Units to English Equivalents
When You Know
Multiply By
To Find
Symbol
centimeters
meters
kilograms
0.3937
3.2808
2.2046
inches
feet
pounds
in. (or ")
ft. (or ')
lb. (or #)
Converting English Units to Metric Equivalents
When You Know
Multiply By
To Find
Symbol
inches
feet
pounds
2.5400
0.3048
0.4535
centimeters
meters
kilograms
cm
m
kg
Converting Temperature
deg. Celsius
deg. Fahrenheit
(ºC x 1.8) + 32 deg. Fahrenheit
(ºF-32) ÷ 1.8 deg. Celsius
ºF
ºC
FOR YOUR RECORDS
Please record the product serial number (located on the right side of the control box), and
the date and place of purchase in the spaces provided below. Refer to this information
when calling GTO for service or assistance with your automatic gate operator.
Serial Number ____________________ Date of Purchase ____________________
Place of Purchase ____________________
Remember to keep all receipts for proof of purchase.
Table of Contents
Gate Operator Class Categories-------------------------------------------------------------inside cover
Units and Standards Conversion Chart----------------------------------------------------inside cover
PLEASE READ THIS FIRST!---------------------------------------------------page iii
Important Safety Instructions --------------------------------------------------- page 1
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Disconnecting the Operator------------------------------------------------------------page 1
Important Safety Instructions for the Consumer-------------------------------------page 2
Secondary Means of Protection Against Entrapment-------------------------------page 5
Required Safety Precautions for Gates------------------------------------------------page 6
Warning Signs and Labels--------------------------------------------------------------page 7
Installation --------------------------------------------------------------------------- page 8
Parts List----------------------------------------------------------------------------------page 8
Technical Specifications --------------------------------------------------------------page 10
Installation Overview -------------------------------------------------------------------page 11
Installing the Mounting Hardware-----------------------------------------------------page 12
Installing the Post Bracket Assembly--------------------------------------------page 12
Installing the Gate Bracket--------------------------------------------------------page 15
Mounting the Operator-------------------------------------------------------------page 16
Installation of the Closed Position Stop----------------------------------------------page 16
Mounting the Control Box--------------------------------------------------------------page 17
Connecting the Operator Power Cable -----------------------------------------------page 18
Installing the Battery--------------------------------------------------------------------page 18
Powering the System --------------------------------------------------------------- page 19
Solar Chart--------------------------------------------------------------------------------page 19
Connecting the Transformer------------------------------------------------------------page 19
Control Board Settings -----------------------------------------------------------page 22
DIP Switches-----------------------------------------------------------------------------page 22
Setting the Closed Position-------------------------------------------------------------page 23
Obstruction Sensitivity------------------------------------------------------------------page 24
Setting Your Personal Transmitter Code -------------------------------------- page 25
Installing the Receiver ------------------------------------------------------------ page 26
Connecting Accessories ----------------------------------------------------------- page 27
Input Connections -----------------------------------------------------------------------page 27
Wiring Accessories - --------------------------------------------------------------------page 28
Push to Open Installation --------------------------------------------------------- page 29
Setting Open Position Limit -----------------------------------------------------------page 31
Troubleshooting Guide-------------------------------------------------------------page 32
Repair Service ----------------------------------------------------------------------page 35
Column Installation Information ----------------------------------------------- page 36
Accessory Catalog ----------------------------------------------------------------- page 37
PLEASE READ THIS FIRST!
Thank you for purchasing a GTO/PRO® 4000XL When correctly installed and properly used, your GTO/PRO®
4000XL Operator will give you many years of reliable service. Please read the following information to ensure you
have the correct system for your particular needs. This manual will enable you to properly install your GTO/PRO®
4000XL Automatic Gate Operator.
The GTO/PRO® 4000XL Operator is designed for installation on a pull-to-open or push-to-open single leaf
gate. The gate must not exceed 20 feet in length (per leaf) nor weigh more than 1000 pounds (per leaf) (please see
Technical Specifications on page 10). The GTO/PRO® 4000XL Operator can be used on vinyl, aluminum, chain
link, farm tube, and wrought iron gates. Use on solid (wood) gates is not recommended. Solid surface gates have a
high resistance to the wind. If the wind is strong enough, the operator will obstruct and stop.
The GTO/PRO® 4000XL Operator accommodates extra transmitters, digital keypads, solar panels, push buttons,
automatic gate locks, and other access control products. These optional accessories (see the Accessory Catalog) are
available.
The GTO/PRO® 4000XL Operator features adjustable obstruction sensing. This safety feature makes the gate
stop and reverse direction within 2 seconds when it comes in contact with an obstruction. MIN is the factory setting;
meaning the gate will exert the minimum force on an obstruction before it stops and reverses direction.
The GTO/PRO® 4000XL Operator also has an adjustable auto-close feature. After the gate reaches the fully open
position, it can be set to remain open up to 120 seconds before automatically closing. Pressing the transmitter button
at any time after the gate opens fully will cause it to close immediately. OFF is the factory setting; meaning the gate
will stay open until you press the transmitter (or keypad, etc.) again.
Please call GTO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our GTO/PRO®
professional line of gate operators and accessories. Our Sales Department will be glad to give you the name and phone
number of a GTO/PRO® dealer near you.
BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPERATOR:
Read these instructions carefully and completely to become
familiar with all parts and installation steps.
You must read the installation manual for detailed instructions on
gate operator safety and proper use of the gate operator.
iii
IMPORTANT SAFETY INSTRUCTIONS
Because automatic gate operators produce high levels of force, consumers need to know the potential hazards associated with
improperly designed, installed, and maintained automated gate operator systems. Keep in mind that the gate operator is
just one component of the total gate operating system. Each component must work in unison to provide the consumer with
convenience, security, and safety.
This manual contains various safety precautions and warnings for the consumer. Because there are many possible
applications of the gate operator, the safety precautions and warnings contained in this manual cannot be completely
exhaustive in nature. They do, however, provide an overview of the safe design, installation, and use of this product.
CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS, WARNINGS, AND INSTALLATION
INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.
Precautions and warnings in this manual are identified with this
warning symbol. The symbol identifies conditions
that can result in damage to the operator or its components, serious injury, or death.
Because GTO automatic gate operators are only part of the total gate operating system, it is the responsibility of the
consumer to ensure that the total system is safe for its intended use.
To Manually Open and Close the
Gate, Follow the Procedure Below:
CAUTION: The gate will move freely and uncontrolled when the gate operator is
removed from the gate. ONLY disconnect the operator when the control box power switch is OFF and the gate is NOT moving.
Disconnecting the Operator
Front Mount
1. Turn control box power switch OFF.
2. Remove hairpin clip, clevis pin, and bushing
from either the front or rear mounting point.
3. Remove the opener from the mount.
Clevis Pin
Gate Bracket
The gate can be opened and closed manually
when the operator is disconnected.
Bushing
Hairpin Clip
NOTE: Substitute a Pin Lock for the clevis pin on the front
mount of the gate operator to prevent unauthorized removal of
the operator from the gate (see Accessory Catalog). 1
IMPORTANT SAFETY INSTRUCTIONS
For The Consumer
WARNING: To reduce the risk of injury or death:
1.
READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction
manual could cause severe injury and/or death, for which the manufacturer cannot be held responsible.
2.
When designing a system that will be entered from a highway or main thoroughfare, make sure the system is placed
far enough from the road to prevent traffic congestion.
3.
The gate must be installed in a location that provides adequate clearance between it and adjacent structures when
opening and closing to reduce the risk of entrapment. Swinging gates must not open into public access areas.
4.
The gate and gate operator installation must comply with any applicable local codes.
I. Before Installation
1. Verify this operator is proper for the type and size of gate, its frequency of use and the proper class rating.
2.
Make sure the gate has been properly installed and swings freely in both directions. Repair or replace all worn or
damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will enhance
the performance of the operator and safety devices used with the system.
3.
Review the operation of the system to become familiar with its safety features. Understand how to disconnect the
operator for manual gate operation (see page 1).
4.
This gate operator is intended for vehicular gates ONLY. A separate entrance or gate must be installed for
pedestrian use (see page 6).
5.
Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS THE
PATH OF A MOVING GATE.
6.
Pay close attention to the diagram below and be aware of these areas at all times.
ZONE 2
ZONE 1
Entrapment
Zones for a
Pull-To-Open
Application
ZONE 3
ZONE 5
ZONE 4
2`WdSeOg
2
5ObSW\bVS
=^S\>]aWbW]\
IMPORTANT SAFETY INSTRUCTIONS
Entrapment Zones for a proper Pull-To-Open installation:
Zone 1 – leading edge of the gate and the fence post.
Zone 2 – between the gate and the gate post.
Zone 3 – the path of the gate.
Zone 4 – the space between the gate in the open position and any object such as a wall, fence, tree, etc.
Zone 5 – pinch points between the opener and gate.
II. During Installation
1.
Install the gate opener on the inside of the property and fence line. DO NOT install an opener on the outside of the
gate where the public has access to it.
2.
Be careful with moving parts and avoid close proximity to areas where fingers or hands could be pinched.
3.
Devices such as contact sensors (safety edges) and non contact sensors (photo beams) provide additional protection
against entrapment.
4.
If push buttons or key switches are installed, they should be within sight of the gate, yet located at least 10 feet from
any moving part of the gate (see diagram below). Never install any control device where a user will be tempted to
reach through the gate to activate the gate opener.
5.
Do not activate your gate opener unless you can see it and can determine that its area of travel is clear of people,
pets, or other obstructions. Watch the gate through its entire movement.
6.
Secure outdoor or easily accessed gate opener controls in order to prohibit unauthorized use of the gate.
Pull-To-Open
Application
Moving Gate
Area
2`WdSeOg
NEVER INSTALL
any control device
within gray area
3
IMPORTANT SAFETY INSTRUCTIONS
III. After Installation
1.
Attach the warning signs (included) to each side of the gate to alert the public of auto­matic gate operation. It is
your responsibility to post warning signs on both sides of your gate. If any of these signs or warning decals become
damaged, illegible or missing, replace them immediately. Contact GTO for free replacements.
2.
The gate is automatic and could move at any time, posing a serious risk of entrapment. No one should be in contact
with the gate when it is moving or stationary.
3.
Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a complete stop.
4.
Do not attempt to "beat the gate" while the gate is closing. This is extremely dangerous.
5. Do not allow children or pets near your gate. Never let children operate or play with gate controls. Keep the
remote controls away from children and unauthorized users; store controls where children and unauthorized users do
not have access to them.
6.
KEEP GATES PROPERLY MAINTAINED. Always turn power to operator OFF before performing any
maintenance. Clean the push-pull tube with a soft, dry cloth and apply silicone spray to it at least once per month.
7.
Service the gate and gate operator regularly. Grease hinges, spray push pull tube with high quality silicone spray and
replace the battery every 3-5 years.
8. To operate this equipment safely, YOU must know how to disconnect the operator for manual gate operation
(see page 1). If you have read the instructions and still do not understand how to disconnect the operator, contact the
GTO Service Department.
Disconnect the operator ONLY when the power is TURNED OFF and the gate is NOT moving.
9. 10.
Make arrangements with local fire and law enforcement for emergency access.
11. Distribute and discuss copies of the IMPORTANT SAFETY INSTRUCTIONS section of this manual with all
persons authorized to use your gate.
12.
IMPORTANT: Save these safety instructions. Make sure everyone who is
using or will be around the gate and gate operator are aware of the dangers
associated with automated gates. In the event you sell the property with
the gate operator or sell the gate operator, provide a copy of these safety
instructions to the new owner.
Should you lose or misplace this manual, a copy can be obtained by
downloading one from the GTO/PRO® web site (www.gtopro.com), by
contacting GTO, Inc., at 3121 Hartsfield Road, Tallahassee, Florida 32303
or by calling 1-800-543-4283 and requesting a duplicate copy. One will be
provided to you free of charge.
4
IMPORTANT SAFETY INSTRUCTIONS
Secondary Means of Protection Against
Entrapment
As specified by Gate Operator Safety Standard, UL 325 (30A.1.1), automatic gate operators shall have an inherent
entrapment sensing system, and shall have provisions for, or be supplied with, at least one independent secondary means to
protect against entrapment. The GTO/PRO® 4000XL utilizes Type A, an inherent (i.e., built-in) entrapment sensing system
as the primary type of entrapment protection. Also, the GTO/PRO® 4000XL has provisions for the connection of Type B2
protection to be used as the secondary type of entrapment protection, if desired.
1. For gate operators utilizing a contact sensor (e.g., safety edge sensor– Type B2) in accordance with UL 325 (51.8.4 [i]):
A. One or more contact sensors shall be located at the leading edge, bottom edge, and post edge, both inside and outside of a vehicular swing gate system.
B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage.
C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended end-use conditions.
Leading Edge Contact Sensor
on both sides of the gate
Vehicular Gate
Post Edge Contact Sensor
on both sides of the gate
Bottom Edge Contact Sensor
on both sides of the gate
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
The GTO/PRO® 4000XL Automatic Gate Operator is designed to stop and reverse within 2 seconds when the
gate comes in contact with an obstruction. Additionally, these operators are equipped with an audio entrapment
alarm which will activate if the unit obstructs twice while opening or closing. This alarm will sound for a period
of 5 minutes, or until the operator receives an intended signal from a hardwired entry/exit source (e.g. push button
control or keypad) and the gate returns to a fully open or fully closed position. Turning the power switch on the
control box OFF and back ON will also deactivate the alarm. Wireless controls such as transmitters and wireless
keypads will not deactivate the alarm.
5
IMPORTANT SAFETY INSTRUCTIONS
Required Safety Precautions for Gates
Install Warning Signs
Warning signs alert people of automatic gate operation and are required when installing the GTO/PRO® 4000XL Automatic
Gate Operator. Furthermore, a walk-through gate must be installed if pedestrian traffic is expected near the vehicular gate.
We recommend using the GTO Bulldog Pedestrian Gate Lock (Call the GTO Sales Department) for controlled access.
GTO Bulldog Pedestrian
Gate Lock
(recommended, not included)
Pedestrian Gate
Contact Sensor
(recommended, not included)
Warning Sign
Vehicular Gate
Photo Beam
Contact Sensor
Contact Sensor
Photo Beam
(recommended, not included) (recommended, not included) (recommended, not included) (recommended, not included)
Entrapment Protection
GTO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily injury in
some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric sensors), which stop and
reverse gate direction upon sensing an obstruction, are suggested for enhanced protection against entrapment.
Warning Signs
! WARNING
The warning signs (at right) must
be installed on both sides of the
gate (see page 7 for details).
Moving Gate Can Cause
Injury Or Death
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
6
IMPORTANT SAFETY INSTRUCTIONS
!
These warning labels should be found
at the locations specified below.
If any of them are missing,
immediately contact GTO for
replacements.
DC SW-4000XL SERIES
Conforms to UL 325 STANDARDS
Maximum Gate: 1000 lb. (453.5 kg); 20 ft. (6.1 m)
US Voltage: 12 Vdc; Frequency: 0 Hz; Power: 60 W
C
LIS ED
T
Class I, II, III and IV Vehicular Swing Gate Operator.
#xxxxxxx
Serial Number: XXXXXXXXXX
TO MANUALLY OPEN AND CLOSE THE GATE:
1. Turn control box power switch OFF.
2. Disconnect front or rear mount from gate bracket.
3. Pull operator away from front or real mounts.
Disconnect operator ONLY when the control box power
switch is OFF and the gate is NOT moving.
GTO, Inc. Tallahassee, Florida USA
Product identification and manual operation instruction
label (1) installed on right side of control box.
Warning signs (2 enclosed) to be installed on each side
of the gate (3–5 feet above the bottom of the gate).
!
WARNING
MOVING GATE
®
Can Cause Injury or Death
1.
2.
3.
1-800-543-GATE (4283) • www.gtopro.com
KEEP CLEAR! Gate may move at any time.
Do not allow children to operate gate or play in
gate area.
This gate is for vehicles only. Pedestrians must
use separate entrance.
Logo and warning labels (2) installed on each side of operator housing.
7
Single Gate Operator Parts List
Operator and Mounting Hardware
ENE
TE OP
E-Z GA
R
Customer Support Card (1)
Master Operator Arm (1)
PRO4000ARMXL
6’ Power Cable
BRACKET BOX - HB4000
Closed Position
Stop Plate (1)
Gate Bracket (1)
Post Bracket (1)
Post Pivot Bracket (1)
HARDWARE BAG - H200HD
1/2" x 10" Carriage Bolt (2)
1/2" x 2-3/4" Bolt (2)
1/2" Lock Nut (4)
3/8" x 3-3/4" Bolt (2)
3/8" Washer (3)
3/8" x 3-1/2" Clevis Pin (1)
3/18" Lock Nut (2)
3/8" x 1-3/4" Clevis Pin (1)
Hairpin Clip (2)
3/8" x 3/4" Bushing (2)
8
3/8" x 3/16" Bushing (2)
2" Receiver Mounting Screw (5)
8" Nylon Cable Tie (10)
1/2" Washer (4)
Single Gate Operator Parts List (continued)
Control Box and Electrical Components
Batteries (2)
RB500
Receiver (1)
AQ201NB
Transformer (1)
RB570
GTO Transmitter (1)
RB741
! WARNING
Moving Gate Can Cause
Injury Or Death
Control Box w/
Control Board (1)
PRO3040CBOX
FF
ON/O
1.
KEEP CLEAR! Gate may move at any time.
2.
Do not allow children to operate gate or
play in gate area.
3.
This gate is for vehicles only. Pedestrians
must use a separate entrance.
Warning Signs (2)
3/8” Bit
Tools Needed
• Power Drill
• Open End Wrenches - 3/8",7/16",1/2",9/16"
Pliers
• 3/8" Drill Bit
• Pliers
Hack Saw
• Hacksaw or Heavy Duty Bolt Cutters
Hammer
• Small (Flat Head) Screwdriver
• Phillips Head Screwdriver
Flat Head
• Tape Measure
Screwdriver
Open End Wrenches
• Level
3/8”, 7/16”, 1/2”, 9/16”
• Wire Strippers
Phillips Head
Screwdriver
• C-Clamps — small, medium, and large
Level
Small
Wire
Tape
• Center Punch
Adjustable
Clamps
Flat Head
Small, Medium, Large
Stripper
Measure
Wrench
• Adjustable Wrench
• Extra person will be helpful
OTHER MATERIALS YOU MAY NEED BEFORE YOU START THE INSTALLATION:
Depending on the type of gate and fence post, you may need some additional materials/hardware. Some of these items can be
found in the GTO/PRO Accessory Catalog.
Drill
Center
Punch
Pen
5/16” Bit
• Low voltage wire may be needed. Length depends upon the distance between the transformer power supply and the control
box. See page 19, Powering the System and the Accessory Catalog for wire and solar charging panels.
• If the gate is more than 1000' away from an AC power source you will need to use at least one GTO Solar Panel to trickle
charge the battery. See the Accessory Catalog.
• The diameter of the fence post should be at least 8" (round) or 6" (square) in order to mount the post bracket (see page 12).
• Depending upon the diameter of the fence post, you may need longer carriage bolts than those provided. Bolts should be at
least 1" longer than the diameter of the fence post (see page 12).
• A horizontal or vertical cross member or mounting plate may be needed to mount the operator to the gate (see page 11).
•
Surge protection for transformer.
•
Some types of installations require U-Bolts.
• Weatherproof cover for transformer if installed outside.
•
For push-to-open applications you must have PTO Bracket R4KPTO.
•
Metal plate for wooden posts (see page 12).
•
Mounting plate for decorative gate (see page 15).
9
Technical Specifications
GTO/PRO® 4000XL AUTOMATIC GATE OPERATOR
DRIVE
• Low friction screw drive (linear actuator) rated for -5 ºF to +160 ºF (-21 ºC to +71 ºC). Use of heater bands on arm and
control box will enhance performance in extreme cold temperatures.
• Powered by a 12 V motor with integral case hardened steel gear reducer. Motor speed reduced to 300 rpm. Generates
1,120 ft. lbs of torque at 12 V.
• Maximum opening arc of 110º. Approximate opening time (90º): 18-22 seconds, depending on weight of gate.
POWER
• The system is powered by a 12 Vdc, 7.0 Ah, sealed, rechargeable acid battery.
• Battery charge is maintained by a 120 Vac, 18 Vac output transformer rectified to 14.5 Vdc (40 VA) through the GTO
control board. Blade-style control board fuse is rated for 25 A.
NOTE: The transformer should not be directly connected to any battery. Do not replace fuses with higher ampere rated fuses; doing so will void your warranty and may damage your control board.
• For optional solar charging see page 19.
CONTROL
• GTO microprocessor-based control board is set for single leaf, pull-to-open gate installations. DIP switches can be
adjusted to accommodate an optional kit for push-to-open gates (see Accessory Catalog).
• Control board has temperature compensated circuits.
• A circuit on the control board regulates charging. "Sleep draw" is 40 mA; "active draw" is 5 to 9 A.
• Auto-memorization of digital transmitter code.
• GTO remote-mounted RF receiver tuned to 318 MHz.
• Operator length with push-pull tube fully retracted is 461/4", mounting point to mounting point, arm stroke 22" max.
• Minimum gate length is 8 ft.
• Adjustable auto-close timer (15 to 120 s), and obstruction sensitivity.
• Power terminal block accommodates a transformer or solar panels (not both).
• DIP switches simplify setup of gate operator.
• Accessory terminal block fully compatible with push button controls, digital keypads, safety loops, etc.
• Control board allows connection of safety edge sensors and photoelectric sensors.
• Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.
OPERATIONAL CAPACITY
• The Gate Capacity Chart shows approximate cycles, per day, you can expect from the GTO/PRO® 4000XL Automatic Gate Operator when powered with a transformer. Actual cycles may vary slightly depending upon the type and
condition of gate and installation.
Gate Capacity Chart GTO/PRO 4000XL
Gate Length
Estimated number of cycles are based on use with a transformer and one(1) 12 Volt battery on a single gate system.
20 ft.
16 ft.
12 ft.
8 ft.
135
140
145
150
300 lb.
130
135
140
145
400 lb.
125
120
130
125
135
130
140
135
500 lb. 600 lb.
Gate Weight
115
120
125
130
700 lb.
110
115
120
125
800 lb.
105
100
110
105
115
110
120
115
900 lb. 1000 lb.
NOTE: BALL BEARING HINGES SHOULD BE USED ON ALL GATES WEIGHING OVER 250 LB.
To determine the number of cycles the gate operator will perform using solar panels, please see the specifications
listed on page 19 or call (800) 543-1236 or (850) 575-4144 for more information.
* An operation cycle is one full opening and closing of the gate.
These specifications are subject to change without notice.
10
Installation Overview
Pull-to-Open Gates (Gate Opens into the Property)
The diagram shown below is an example of a pull-to-open installation on a chain link fence and single gate. Mounting the
operator on a masonry column requires special procedures; see Column Installation Information on page 36 if you intend
to mount the operator on a column. Furthermore, if you have a push-to-open gate, see Push to Open Installation on page 30
before proceeding.
Receiver
Control Box with Batteries
Gate Swings Evenly and Freely
Hung Firmly and Plumb
Horizontal Cross Member
Post Bracket Assembly
Single Gate Opener
120 Volt indoor
Transformer
(surge protector
not supplied)
Warning Sign
Gate Bracket
Power Cable
Closed Position Positive Stop Plate
Run 1000' (max.) of low
voltage wire to control
box from transformer
(wire not included).
Fence Post Set in Concrete
PVC conduit (not included)
to protect wire from lawn
mowers and weed eaters.
Preparation of the Gate
Step 1
The gate must be plumb, level, and swing freely on its
hinges. Wheels must not be attached to the gate. The
gate must move throughout its arc without binding or
dragging on the ground. Note that gates over 250 lb.
should have ball bearing hinges with grease fittings.
Horizontal Cross Member
Step 2
The fence post must be secured in the ground with
concrete so it will minimize twist or flex when the
operator is activated. We recommend you position the
operator near the centerline of the gate to keep the gate
from twisting and flexing and to avoid backsplash from
the ground. The addition of a horizontal or vertical
cross member (if one is not already in place) to provide
a stable area for mounting the gate bracket is also
important.
Vertical Cross Member
11
Installing Mounting Hardware
Installing the Post Bracket Assembly
The post bracket is designed to work on a flat fence post. Fence posts must be at least 6” square in order to mount the
post bracket.
NOTE: The best method of attaching the post bracket to metal
post is welding. Round wood posts (no smaller than 8” diameter)
may be notched to create a flat surface for attaching the post
bracket.
If bolts are used to mount the post bracket, the bolts must
completely penetrate the fence post. If your fence post is wider
than 8", it will be necessary to use carriage bolts longer than
those supplied. On wood posts use a metal plate (not provided)
between the nuts and post to prevent the operator from pulling
the bolts and washers through the wood.
On masonry columns use red heads or other secure masonary
mounting hardware.
NOTE: A fence post smaller than 6" in diameter or 6" square
should be made of metal instead of wood so that it will remain
stable while the operator is moving the gate.
Recommended Reinforcement Examples
Step 1:
Close the gate and place your level against the
horizontal cross member. The top of the level
should be in the center of the cross member
and should overlap the fence post. Scribe
a line across the cross member and fence
post. You will use this line to help determine
position of gate and post brackets.
12
Step 2:
Position the post bracket on the fence post with the mounting
holes centered over the scribe line. The post bracket should be
flush with the edge of the fence post closest to the gate (see
illustration). Mark the position of post bracket holes on the
fence post.
Step 3:
Drill holes in fence post as marked using a 1/2" drill bit.
Install the post bracket using the 1/2" x 10" carriage bolts,
1/ " washers, and lock nuts (provided)­.
2
Step 4:
Place the end of post pivot bracket with two holes inside
the post bracket. Align the back hole in the post pivot
bracket with back hole in the post bracket.­Insert 1/2" x
33/4" hex head bolt through post pivot bracket and post
bracket and secure with washer, lockwasher and nut.
1/2" x 3-3/4" Bolt
Post Bracket
1/2" Washer
1/2" Lock Washer
1/2" Nut
Post Pivot Bracket
13
Clevis Pin
Step 5:
Position the operator rear mount between post
pivot bracket. Place a small bushing under the rear
mount. Align the hole in rear mount, bushing and
post pivot brackets and secure with the clevis pin
and hair pin clip.
Operator
Hairpin Clip
Small Bushing Goes
Under Rear Mount
Clevis Pin
Front Mount
Gate Bracket
Step 6:
Place a small bushing under the the front mount and
attach the gate bracket to the front mount using the
clevis pin and hairpin clip.
Small Bushing Goes
Under Front Mount
Hairpin Clip
Step 7:
Open the gate to the desired open position. Position the operator so
that the gate bracket rests against the gate along the level scribed
line. Check the clearance between the operator and the gate.
The operator should only make contact with the gate at the gate
bracket. See illustration at right for examples of clearance.
Pinch Area
When you have achieved the best position for the post pivot
bracket in the open position, insert the bolt through the aligned
holes of the post bracket and post pivot bracket to hold it in place.
Gate in the
OPENED POSITION
Clamp the gate bracket to the gate using c-clamps or another type
of clamp.
2" minimum
IMPORTANT: While determining the position of
the post pivot bracket, be sure that the position allows
for minimum 2 inches of clearance between the gate
and the operator in both the open and closed positions,
as shown in Steps 7 & 8 . This clearance will give the
operator the most efficient leverage point for opening
and closing the gate and more importantly provides the
least possible pinch area.
14
Step 8:
Gate in the
CLOSED POSITION
2" minimum
Remove the clevis pin
from the front mount and
while supporting the gate
operator, swing the gate and
gate operator to the closed
position. With the gate and
gate operator in the closed
position check the clearance
and be sure that the gate
operator is not binding at the
post pivot bracket.
Pinch Area
If you don't have 2 inches of clearance or the gate operator is binding on the post pivot bracket, remove the bolt in
the post bracket and readjust the pivot bracket until you can achieve the proper clearance.
With the post pivot bracket in the optimum position for clearance and freedom of movement, replace the bolt in a
post bracket adjustment hole and return the operator to the open position and recheck the gate operator level and
clearance. Make sure the gate bracket is clamped securely.
Installing the Gate Bracket
Step 9:
Move the operator away from the gate bracket. The mounting holes should be centered over the scribe line. Mark the gate in
the center of the gate bracket holes. Remove the gate bracket and drill the 1/2" holes in the gate cross member and attach the
gate bracket using the 1/2" x 23/4" bolts, washers and nuts.
LEVEL
horizon
tal cros
s mem
ber
Mark cross member through middle of
gate bracket slots and drill 1/2" holes
FRONT VIEW
FRONT VIEW
SIDE VIEW
SIDE VIEW
Round Tube & Chain Link Gate
Mounting Plate Created
for Decorative Gate
Square Tube Gate
(required but not supplied)
15
Mounting the Operator
Step 10
Attach the operator to the securely bolted post bracket assembly and gate bracket using clevis pins, bushings, and hairpin
clips, or optional Pin Locks (see Accessory Catalog). Verify that the operator is level and adjust the post bracket assembly if
necessary.
Gate In Open Position
Level Operator
Clevis Pin, Bushing, and Hairpin Clip
Fence Post
Installation of the Closed Position Stop
The GTO/PRO® 4000XL Gate Operator firmly holds the gate in the closed position using the positive stop plate.
The positive stop helps stabilize the gate leaf in the closed position. To further enhance the stability and security
of your gate, install the optional GTO/PRO® Automatic Gate Lock FM144 (see Accessory Catalog).
Step 11
5ObS6W\US
Remove hairpin, clevis pin, and washer from front mount
and close the gate (remember to support operator). Fasten the
closed position stop plate to the end of the gate frame on the
gate centerline (in line with the operator arm), but do not
tighten it completely. Slide the stop plate toward the fence
post until they touch (see illustration). Once you have moved
the stop plate to the correct position, tighten its hardware
completely.
1Z]aSR>]aWbW]\
Ab]^>ZObS
BVSUObS[cab]^S\
Ÿ[Of
Use the appropriate hardware for your type of gate (use
U-bolts if you have a tube or chain link gate; wood or lag
screws for wood gates; etc.). This hardware is not provided.
A723D73E
5ObS>]ab
1Z]aSR>]aWbW]\Ab]^>ZObS[]c\bSR
]\[SbOZ^]abeWbVCP]Zba
4S\QS>]ab
B=>D73E
16
At this stage of the installation, the operator should be installed on
the gate and the closed position stop should be in place.
Check List
• The gate is plumb, level, and swings smoothly on its hinges.
• A plate or support was added for the gate bracket (if necessary).
• The operator is level and mounted on the centerline of the gate.
Closed Position Stop Plate
CL
Gate In Closed Position
Mounting the Control Box
Step 1
Mount the control box using the screws (provided) or another
secure mounting method. The control box must be mounted at
least 3 feet above the ground to protect it from rain splash, snow,
etc., and at least 3 feet from an AC power source to prevent
electrical interference.
25
STALL FORCE
BATT+
BATTON DIP
17
AUTO CLOSE TIME
FUSE
1 2 3 4
Use mounting
holes and screws
provided to mount
control box to a
secure surface.
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
S4
POWER
INPUTS
GTO
CONTROL
OUTPUTS
LOCK
AUX
RLY
GTO
LOCK
AUX
PWR
18 VAC
or
SOLAR
RECEIVER
SLAVE CABLE
MASTER CABLE
SLAVE INPUTS
MASTER INPUTS
CONTROL INPUTS
RECEIVER
ALM
Connecting Operator Power Cable
Step 1
Make sure the control box power switch is in the OFF position.
The ON/OFF Switch is located on the bottom of the control
box. Remove the control box cover and slide the battery into
position with its terminals to the BOTTOM (see illustration).
Connect the BLACK battery wire to the NEGATIVE
(–)Battery
battery
Single
Installed Horizontally
terminal. Connect the RED battery wire to the POSITIVE
(+)
terminals
on the
right.
terminal. Pay close attention to the color of thewith
wires.
If the
wires
are connected incorrectly, the control board will be damaged.
NEVER insert the battery with the terminals to the top.
BLACK
Batteries
Installed Vertically
with terminals on bottom.
RED
BLACK wire to NEGATIVE (–) terminal
RED wire to POSITIVE (+) terminal
Step 2
12 V Batteries (Included)
Strip approximately 3/16" of insulation from each wire of
the opener power cable. Twist each exposed wire tightly
(there are seven [7] wires inside the power cable sheath).
Loosen sealing nut on strain relief hub at bottom of
control box. Insert power cable into control box through
strain relief. Thread approximately 6" of the power cable
into the control box and retighten sealing nut until the
power cable locks into place.
AUTO CLOSE TIME
FUSE
25
STALL FORCE
BATT+
BATTON DIP
1 2 3 4
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
S4
POWER
INPUTS
GTO
CONTROL
OUTPUTS
LOCK
AUX
RLY
GTO
LOCK
AUX
PWR
18 VAC
or
SOLAR
RECEIVER
SLAVE CABLE
MASTER CABLE
SLAVE INPUTS
MASTER INPUTS
CONTROL INPUTS
RECEIVER
ALM
Strain Relief
Lock Nut
Hub
Sealing Nut
Strain Relief
Operator Power Cable
GRN
Step 3
BRN
ORG
RED
BLK
COM
COM
CYCLE
CLOSE
SAFETY
EXIT
OPEN
SHADOW
LOOP
CLOSE
EDGE
Wrong
OPEN
EDGE
Terminal �
Block
18
Wire
Terminal �
Block
RECEIVER
Wire
RED
Terminal �
Block
BLK
RECEIVER
Wire
GRN
together. Splicing
permits corrosion and
seriously degrades the
wire's ability to carry
an adequate current.
Wrong
Correct
CONTROL INPUTS
Power Cable from
the Master Arm
Tighten the set screws against the end of the wires.
A dab of petroleum jelly on each terminal will help
prevent corrosion.
NEVER splice wires
MASTER CABLE
BLUE
MASTER INPUTS
WHT
Insert the stripped power cable wires into the
appropriate terminals on the MASTER INPUTS
terminal block. The green wire should be inserted
into the GRN terminal, the white wire into WHT,
the blue wire into BLUE, brown wire into BRN,
orange wire into ORG, red wire into RED, and the
black wire into the BLK terminal.
Powering the System
Optional Solar Panels and Gate Activity
The table and map
illustrate the maximum
number of gate cycles
to expect per day in a
particular area when using
from 10 to 30 watts of
solar charging power.
(see Accessory Catalog).
The figures shown are
for winter (minimum
sunlight) and do not account for the use of any
accessory items. Accessories connected to
your system will draw additional power from
the battery.
Winter Ratings
12 v single gate (10 watts) solar charger 12 v single gate (15 watts) solar charger 12 v single gate (20 watts) solar charger 12 v single gate (25 watts) solar charger 12 v single gate (30 watts) solar charger Zone 1
8
11
14
17
20
Zone 2
Zone 3
16
20
28
36
44
26
30
38
46
54
NOTE: A minimum of 10 watts solar charging
power is needed to charge the batteries.
IMPORTANT:
•
If your gate is more than 1000 ft. from an ac power source, you will need to use at least 10 watts solar
charging power to charge the batteries (see Accessory Catalog). Refer to the Solar Panels and Gate
Activity chart above.
•
The transformer is designed and intended for indoor use. If the transformer can be plugged only into
an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores)
must be used.
•
All low voltage wire used with the GTO PRO® Gate Opener must be 16 gauge dual conductor,
multi-stranded, direct burial wire (see page 20 and the Accessory Catalog). Do not run more than
1000 feet of wire.
Installation of the Transformer
Step 1
Make sure the power switch is OFF before proceeding to the next step.
Step 2
FF
ON/O
ON/OFF Switch
Select the electrical outlet outlet into which you will plug the transformer.
Measure the distance from this outlet to the control box following the path
where the wire will be laid. After you have measured how much wire is
needed, cut the wire to the appropriate length.
19
IMPORTANT INFORMATION ABOUT LOW VOLTAGE WIRE
The only wire acceptable for use with GTO products is 16 gauge multi-stranded, low voltage, PVC
sheathed wire. This particular gauge enables the transformer to provide an adequate charge through the
control board to the battery at distances up to 1000 ft.
DO NOT use telephone wire or solid core wire. Unlike multi-stranded wire, these types of wire are
inadequate for use with your gate opener system. Telephone wire and solid core wire do not deliver
enough voltage for your gate opener to function and will cause the system to go into a condition known
as "low voltage lockout."
NEVER splice wires together. Splicing permits corrosion and seriously degrades the wire's ability to
carry an adequate current.
12 V Batteries
Step 3
Lay the measured length of low voltage wire in a trench following a path
from the selected electrical outlet to the control box. Wires coming up
from the ground should be run through PVC conduit to protect them from
lawn mower blades, weed eaters, and grazing animals. Be sure to bury the
wire laid in the trench.
AUTO CLOSE TIME
FUSE
25
STALL FORCE
BATT+
BATT-
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
S4
Feed the low voltage wires upward through the strain relief opening on the
lower left of the control box. Pull 6" to 8" of wire into the control box.
WARNING! DO NOT PLUG THE TRANSFORMER
INTO AN OUTLET DURING THIS STEP! THE
TRANSFORMER MUST ONLY BE PLUGGED INTO
AN OUTLET DURING STEP 7!
POWER
INPUTS
GTO
CONTROL
OUTPUTS
LOCK
AUX
RLY
GTO
LOCK
AUX
PWR
18 VAC
or
SOLAR
RECEIVER
SLAVE CABLE
MASTER CABLE
SLAVE INPUTS
MASTER INPUTS
RECEIVER
PVC Pipe
AUX
RLY
AUX
GRN
BRN
ORG
RED
SLAVE CABLE
BLUE
SLAVE INPUTS
WHT
BLK
GRN
BRN
ORG
RED
MASTER CABLE
BLUE
MASTER INPUTS
BLK
Power Cable
from Master Arm
WHT
Tighten set screws against exposed end of wires. A
dab of household petroleum jelly on each terminal will
help prevent corrosion.
CONTROL
OUTPUTS
PWR
LOCK
GTO
LOCK
Insert one transformer wire into an GTO TRANSF
terminal. Insert the other transformer wire into the
remaining GTO TRANSF terminal. The transformer
wires can be connected to the GTO TRANSF
terminals regardless of color or polarity.
POWER
INPUTS
GTO
TRANSF
or
18 VAC
Low Voltage Wire
from AC Transformer
or Solar Panel
SOLAR
RED
BLACK
20
CONTROL INPUTS
ALM
Power Cable
from Master Arm
Low Voltage Wire
from Transformer
or Solar Panel
~ ~
Step 5
Strip 3/16" off the ends of the low voltage wire and
twist tightly. Attach these ends to the GTO TRANSF
(GTO Transformer) terminals located on the POWER
INPUTS (GTO Transformer) terminal block (see
illustration at right). Be certain not to let the
exposed wires touch each other!
ON DIP
1 2 3 4
Step 4
Step 6
Strip 1/2" of insulation from the ends of the low voltage
wire. Attach these stripped ends to the transformer
terminals.
A dab of household petroleum jelly on each terminal will
help prevent corrosion.
Make sure the exposed wires do not touch each other!
Step 7
Plug the transformer into the electrical outlet.
(Use of a surge protector with the transformer is strongly
recommended.)
NOTE: This is a class II indoor transformer.
IMPORTANT: If using transformer outdoors be sure
to enclose it in a weatherproof case.
HINT: Keep a few mothballs in the control box to
discourage insects from entering it and damaging the
control board.
21
CONTROL BOARD SETTINGS
ON
OFF
DIP Switch #1 - Soft Start/Stop
ON - Soft start enabled (factory preset).
OFF - Soft start disabled.
The Soft Start/Stop feature slowly starts the
gate as it begins to open and slows the gate as
it comes to the closed position. This saves wear
and tear on the gate and gate opener system.
DIP
Main DIP Switch Settings (MODES)
ON
1 2 3 4
DIP Switches
DIP Switch #2 - Warning Buzzer
ON - Buzzer warning enabled (factory preset).
OFF - Buzzer warning disabled.
The Warning Buzzer alerts you when the gate
opener is beginning to either open or close the
gate. It sounds for the first 2 seconds in each
direction. It also sounds a warning when the gate
obstructs two times in one cycle. Switching this
to OFF only disables the open and close warning
not the obstruction warning.
AUTO CLOSE TIME
STALL FORCE
STATUS
LEARN RMT
OFF
120
MAX
ON DIP
OFF
OFF
PULL
DLY.
OFF
OFF
1 2 3 4
SOFT START
WARNING
OPEN
SLV OPEN
MODE1
MODE2
MIN
ON
ON
PUSH
SIMULT.
ON
ON
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
DIP Switch #3 - Push/Pull-to-Open
ON - Push to open.
OFF - Pull to open (factory preset).
If your gate opens into the property the DIP
Switch is set to the OFF position (factory
setting). If your gate opens out from the property
the DIP Switch must be set to the ON position.
NOTE: if you have a Push-to-Open gate
application you will need a Push-to-Open bracket
(see Push-to-Open Instructions on page 30).
S4
DIP Switch #4 - Dual Operation
ON - Slave opens simultaneously with master.
OFF - Slave opens after master.
Note: Not applicable for single gate operator.
Auto Close
AUTO CLOSE TIME
The 'AUTO CLOSE TIME' potentiometer
controls auto close feature.
Turning the pot all the way counter-clockwise
will turn auto close feature off. The minimum
auto close time is 3 seconds. The maximum
(turn the potentiometer all the way clockwise)
auto close time is 120 seconds.
STALL FORCE
STATUS
LEARN RMT
OFF
OFF
OFF
MAX
ON DIP
MODE1
MODE2
Auto Close Time
Potentiometer
OFF
OFF
PULL
DLY.
MIN
1 2 3 4
SOFT START
WARNING
OPEN
SLV OPEN
120
ON
ON
PUSH
SIMULT.
S3
LEARN
MAST LIMIT
ON
ON
S2
LEARN
22
Setting the Closed Position Limit
for Pull to Open Applications
NOTE: For heavier gates you may need to increase the stall force (see pg 24). If the gate still does not open or close to the
limits you have set, check to ensure that the gate installation was performed correctly according to the guidelines set forth on
page 11. If the transmitter does not activate the gate operator you may have to reset the transmitter code (see pg 25).
TURN CONTROL BOX ON
Your GTO PRO® has two Limit Settings
1) OPEN Limit setting: (Gate in the OPEN POSITION / the limit is FACTORY SET and NOT ADJUSTABLE) The open
limit setting is the fully open position. The tube must be fully retracted.
2) CLOSED Limit setting: (Gate in the CLOSED POSITION) To achieve optimum closed position, you are required
to complete the following FOUR STEPS:
Step 1
Confirm that the power switch is in the ON position and the gate
is in the OPEN POSITION.
CLOSE TIME
STALL FORCE
STATUS
LEARN RMT
ART OFF
G
OFF
PULL
EN DLY.
OFF
OFF
1 2 3 4
Activate your opener by pressing the entry transmitter button.
Your gate should now be moving from the fully open position
toward the closed position. Prepare to STOP the gate by pressing
the entry transmitter button again when the gate reaches the
desired closed position. This step may be repeated until desired
close position is achieved. Once the desired CLOSED position
has been achieved, proceed to step 3.
MIN
MAX
ON DIP
Step 2
120
ON
ON
PUSH
SIMULT.
S3
LEARN
MAST LIMIT
ON
ON
S2
LEARN
SLV LIMIT
S4
Learn Master Limit
Button
Step 3
With the gate in the desired closed position PRESS & HOLD
the “LEARN MAST LIMIT" button on the control board for 5
seconds.
Step 4
Press the transmitter button and allow the gate to return to the
fully open position. YOUR GATE’S CLOSED POSITION LIMIT IS NOW PROGRAMMED.
TESTING YOUR CLOSED LIMIT SETTING:
Press your entry transmitter and allow your gate to close. If the CLOSED position is not correct or needs to be changed, you
will need to CLEAR your CLOSED LIMIT settings and follow Steps 1-4 again.
CLEARING THE PROGRAMMED CLOSED LIMIT SETTING:
If you make a mistake and set the limit at the wrong position – press your transmitter to return the gate to the fully opened
position, then press and hold the "LEARN MAST LIMIT" button for 5 seconds. This will clear the memory for the closed
limit position. Follow Steps 1-4 again.
23
Obstruction Sensitivity Potentiometer
STALL FORCE
AUTO CLOSE TIME
OFF
MAX
The Stall Force potentiometer on
the control board operates like a
volume control on a radio. It controls the obstruction
sensitivity (or the amount of force the opener will apply to an
obstruction) before it automatically stops and reverses direction for
approximately two (2) seconds.
SOFT START
WARNING
OPEN
SLV OPEN
MODE1
MODE2
OFF
OFF
PULL
DLY.
OFF
OFF
MIN
MAX
ON DIP
MIN
120
STALL FORCE
1 2 3 4
IMPORTANT: For safety reasons
the obstruction setting or Stall
Force on the GTO PRO® control
board comes from the factory set at
MIN (minimum). In many gate installations this setting will need to
be adjusted to overcome the weight
and size of the gates.
ON
ON
PUSH
SIMULT.
ON
ON
Use a small slotted screwdriver to turn the arrow in the center of the
potentiometer. Adjust the stall force from the MINIMUM position
where the gate operates without obstructing from its own weight or the
wind conditions in your area.
ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR
SERVICING YOUR AUTOMATIC GATE OPENER!
NOTE: YOU MAY NEED TO INCREASE THE STALL FORCE IN COLD TEMPERATURES DUE TO
INCREASED RESISTANCE FROM GATE HINGES.
24
Setting Your Personal Transmitter Code
All GTO transmitters are set to a standard code at the factory and are ready to operate your GTO PRO® Gate Opener®. For
your safety and security, however, we strongly recommend that you replace the factory setting with your own personal code.
Follow the directions below:
1. Remove the Transmitter Cover
On the back of the transmitter use a small phillips head screw driver to remove
the two screws on the sides of the visor clip and separate the front cover from the
transmitter. With the front cover removed, the battery and the DIP switches will
be exposed. To set a new code, use a small screwdriver to move the switches.
LE
D
0
–
+ 1
2
3
4
5
A2
AL
3S
L
KA
IN
E
12
BA
TT
ER
2. Set the transmitter DIP Switches
There are nine (9) transmitter DIP switches; each can be placed in three different
positions (+, 0, –). DO NOT set all the switches in the same position, such as all +,
all 0, or all –. Once the DIP switches have been set to a personal code, replace front
cover.
6
7
8
9
EC
E
V
Y
1 2 3 4 5 6 7 8 9
+
0
ECE
WARNING: No other adjustments should be made inside the transmitter.
3. “Teach” the New Code to Control Board Memory
CLOSE TIME
STALL FORCE
STATUS
LEARN RMT
120
OFF
OFF
MAX
ON DIP
ART OFF
G
OFF
PULL
EN DLY.
MIN
1 2 3 4
A.
Press and hold transmitter button.
B. Press and hold the LEARN RMT (Learn Remote) button on the control board until the buzzer sounds.
C. Release transmitter button. The new code
is stored in control board memory.
D. Release the LEARN RMT (Learn Remote) button.
ON
ON
PUSH
SIMULT.
ON
ON
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
S4
25
Learn Remote
Button
Installing the Receiver
Use the transmitter to check the range of the receiver before permanently mounting it.
Consider the following when mounting the receiver:
• Standard receiver cable length is 10 feet (receivers with a longer cable are available as
special order items; call the GTO Sales Department). NEVER splice receiver cable!
• Run the cable through PVC conduit to protect it from damage.
• DO NOT run cable through metal conduit because the receiver signal range will be
decreased.
• DO NOT run cable in conduit containing ac wiring.
• The receiver range can vary from 50 to 100 feet depending upon weather, topography,
and external interference.
• DO NOT mount upside down.
• DO NOT mount on metal fence or post; doing so will decrease signal range.
• MOUNT so that you have line of sight between remote to antenna.
• MOUNT 3 feet away from AC voltage.
• MOUNT as high as possible for optimum range.
FCC Regulation
This device complies with FCC rules Part 15. Operation is subject to the following
conditions:
1. This device may not cause harmful interference.
2. This device must accept an interference that may cause undesired operation.
Transmitter distance may vary due to circumstances beyond our control. NOTE:
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate the equipment.
26
E
BLK
GRN
Input Connections
BLUE
BRN
ORG
RED
MASTER CABLE
WHT
MASTER INPUTS
NOTE:
• All control inputs are dry-contact, normally open, inputs. DO NOT apply external voltage sources to these inputs.
• All inputs are connected with respect to COMMON terminal.
• The status LED will blink once when its corresponding input is activated.
1 COM: Circuit common (reference for all logic input)
• Two (2) terminals to provide extra common connection point.
RED
S
Connecting Accessories
BLK
1
EXIT
OPEN
SHADOW
LOOP
6
CLOSE
EDGE
7
OPEN
EDGE
GRN
BLK
RED
7 OPEN EDGE: (Typically for use with safety edge device)
• Activation of this input while the gate is opening will cause the gate to stop and reverse direction for approximately 2 seconds.
• Activation of this input while the gate is closing has no effect (gate will continue to close).
• Activation of this input while gate is idle will prevent gate from opening.
ALM
6 CLOSE EDGE: (Typically for use with safety edge device)
• Activation of this input while the gate is closing will cause the gate to stop and reverse direction for approximately 2 seconds.
• Activation of this input while the gate is opening has no effect (gate will continue to open).
• Activation of this input while gate is idle will prevent gate from closing.
CONTROL INPUTS
SAFETY
5
5 SHADOW LOOP: (Typically for use with loop detector device)
• This input is only monitored when the gate is at the fully open
position. At any other position, activation of this input has no effect on gate operation.
• Activation of this input while gate at the fully open position will
prevent gate from closing.
27
CYCLE
CLOSE
RECEIVER
4 EXIT/OPEN: (Typically for use with exit loop or wand)
• Activation of this input will open the gate if it’s not already at the
open position
• Activation of this input while at open limit will restart the auto close time
(if enabled).
COM
3 SAFETY: (Typically for use with photo beam device, loop detector
or other non-contact sensors)
2
• Activation of this input while the gate is closing will cause the gate to stop and return to the opened position.
3
• Activation of this input while the gate is opening has no effect (gate will continue to open).
4
• Activation of this input while gate is idle will prevent gate from closing.
COM
2 CYCLE CLOSE: (Typically for use with doorbell button or hardwired key pad)
• Each activation at this input will cycle the operation as follows:
….→ OPEN → STOP → CLOSE → STOP → OPEN → …
Connecting Accessories
Wiring Accessories
BLUE GRN
BRN WHT
ORG BLUE
RED BRN
BLK ORG
RED
COM BLK
COM
MASTER INPUTS
SLAVE INPUTS
1
2
3
4
5
6
OPEN
EDGE
AUXWHT
GRN
CLOSE
EDGE
or
SOLAR
CONTROL INPUTS
SHADOW
LOOP
GTO
LOCK
PWR
EXIT
OPEN
18 VAC
RECEIVER
AUX
SLAVE CABLE
RLY MASTER CABLE
SAFETY
LOCK
CYCLE
CLOSE
GTO
TRANSF
GRN
7
6
7
GTO/PRO
Automatic Gate Lock
BLK
RED
RECEIVER
ALM
According to
Application
1
Edge Sensor
3
4
5
ON
DIP
NO
COM
NC
V+
V–
LOOP
LOOP
1 2 3 4 5 6 7 8 9 10
1
According to
Application
GTO/PRO
Loop Detector
3
1
GTO/PRO
Photo Beams
LOOP
1
2
GTO/PRO
Push Button Control
4
1
GTO/PRO
Vehicle Sensor
1
4
GHI
7
PRS
2
ABC
5
JKL
8
TUV
0
Refer to Vehicle Sensor
manual for additional
connections.
3
DEF
6
MNO
9
WXY
1
2
NOTE: Connections are for typical applications.
There may be additional connection options for
applications that are not illustrated here.
GTO/PRO Keypad
28
Connecting Other Auxiliary Devices (Mag Locks,
Sirens, Lights, etc.}
• These 2 terminals are normally open 'dry-contact' (no voltage) relay ouput.
• These 2 terminals are ON (shorted) whenever the gate is moving and OFF (opened) otherwise.
• These 2 terminals maximum rating is 24Vdc, 1 Amp.
Push to Open Installation
Determining The Mounting Position
of The Post Bracket Assembly
Swinging gates shall not open into public access areas!
A "Push-to-Open" gate opens out from the property.
If you have a pull-to-open gate (gate opens into the property), return to
page 12.
1/2" x 3-3/4" Bolt
In a PUSH-TO-OPEN installation the operators are installed while the
gates are in the closed position.
Post Bracket
NOTE: An optional 12" long Post Pivot Bracket (R4KPTO) is available
for installations that need a greater distance to achieve the safe gate and
gate operator clearance (2 inches).
1/2" Washer
1/2" Lock Washer
Step 1
With the gates closed, adjust the post bracket assembly and the gate
bracket until the operator is level. While holding the operator level,
use C-clamps to temporarily keep the post bracket assembly and
gate bracket in their respective positions on the fence post and gate.
1/2" Nut
Post Pivot Bracket
IMPORTANT: While determining the mounting point for the post
pivot bracket assembly be sure that the position allows for maximum
clearance between the gate and the operator in both the open and closed
positions, as shown in the diagrams below. This clearance will give the
operator the most efficient leverage point for opening and closing the
gate and more importantly provides the least possible pinch area.
Step 2
After verifying that you have the best position
for the post pivot bracket, insert the 5/16" x 1 3/4"
bolt through the aligned holes of the post bracket
and post pivot bracket and fasten it with the 5/16"
washer and nut.
Gate in the Open Position
IMPORTANT: If you loosened the clamp on
the post bracket to achieve the optimum position,
tighten it in its new position and recheck the gate
bracket with the gate in the open position (move the
gate bracket and re-clamp it if necessary).
Pinch Area
2" minimum
Gate in the Closed Position
Pinch Area
2" minimum
29
Step 3
With the gate in the fully closed position and the operator retracted, align the operator to the gate. Mark reference points
for bolt holes on gate cross member through middle of gate bracket slots. The operator must be level. Drill 3/8" holes into
the gate cross member as marked. Fasten gate bracket to cross member using (2) 3/8" x 3" bolts, washers, lock washers, and
nuts. Attach the operator to the post bracket assembly and gate bracket using clevis pins, bushings, and hairpins clips.
Gate In Closed Position
Level O
perato
r
Clevis Pin, Bushing, and Hairpin Clip
3
4
OFF
ON
ON
MAX
MIN
120
OFF
OFF
PULL
DLY.
OFF
OFF
MODE1
2
OFF
1
ON DIP
1 2 3 4
SOFT START
WARNING
OPEN
SLV OPEN
ON
ON
AUTO CLOSE TIME
Make sure the control box power switch is OFF. Use a small
screwdriver to move the Number 4 DIP switch from the factory
setting (OFF / Pull-To-Open) to ON for Push-To-Open. Turn
power switch ON. The control board is now configured to push
the gate open.
STALL FORC
FORCE
ORC
Step 4
ON
ON
PUS
PUSH
SIMU
SIMULT.
Fence Post
DIP#3
ON
Push-to-open operation.
OFF Pull-to-open operation (factory setting).
30
Setting the Open Position Limit
Step 1
Confirm that the power switch is in the ON position, and the gate is in the CLOSED POSITION.
Step 2
Activate your opener by pressing the entry transmitter button. Your gate should now be moving from the closed position
toward the open position. Prepare to STOP gate by pressing the entry transmitter button again when the gate reaches the
desired open position. This step may be repeated until desired open position is achieved. Once the desired OPEN position has
been achieved, proceed to Step 3.
Step 3
With the gate in the desired open position PRESS & HOLD the “LEARN MAST LIMIT" button on the control board for 5
seconds.
Step 4
Press the transmitter button and allow the gate to return to the closed position. YOUR GATE’S OPEN POSITION LIMIT IS
NOW PROGRAMMED.
CLOSE TIME
TESTING YOUR OPEN LIMIT SETTING:
LEARN RMT
120
ART OFF
G
OFF
PULL
EN DLY.
OFF
OFF
If you make a mistake and set the limit at the wrong position
– press your transmitter to return the gate to the fully closed
position, then press and hold the "LEARN MAST LIMIT" button
for 5 seconds. This will clear the memory for the
open limit position. Follow steps one (1) to four (4) again.
31
MIN
MAX
ON DIP
CLEARING PROGRAMMED
OPEN LIMIT SETTING:
STATUS
1 2 3 4
Press your entry transmitter and allow your gate to open. If the
OPEN position is not correct or needs to be changed, you will
need to CLEAR your OPEN LIMIT settings and follow steps
one (1) to four (4) again.
STALL FORCE
ON
ON
PUSH
SIMULT.
ON
ON
S3
LEARN
MAST LIMIT
S2
LEARN
SLV LIMIT
S4
Learn Master Limit
Button
Troubleshooting Guide
If your gate opener does not function properly after it is installed, use this guide before calling the GTO Service Department.
Generation 3 Audible Feedback
Symptom
Diagnosis
Check:
1 short beep upon
activation
Blown Fuse
Low or Bad Battery
Loose Battery
Connection
•
•
•
Fuse
Battery Under Load
Battery Harness Connections
1 short beep upon power
up
Circuit Board Powered
Up & Ready
•
Normal Operation
Continuous
Uninterrupted Alarm
Circuit Board Senses an
Obstruction
•
•
•
•
•
Path of Gate
Gate for Level and Plumb
Stall Force Adjustment
Disconnect Safety Devices
Rev Counter
1 beep with 10 seconds
off
Low Battery Condition
•
•
•
Fuses
Battery Harness Connections
Battery Under Load
1 beep then 2 beeps
Master Motor Terminals
Shorted
•
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Motor
Circuit Board
1 beep then 3 beeps
Slave Motor Terminals
Shorted
•
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Motor
Circuit Board
1 beep with
2 seconds off
Master Arm Limit Switch
Error
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Master Input ORG & GRN, BRN & GRN voltage with wires
disconnected. 11VDC across each terminal.
2 beeps with
2 seconds off
Slave Arm Limit Switch
Error
•
•
•
Connections to Slave Inputs
Slave Arm Power Cable
Slave Input ORG & GRN, BRN & GRN voltage with wires
disconnected. 11VDC each across each terminal.
3 beeps with
2 seconds off
Master Arm Rev Counter
Error
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Rev Counter
4 beeps with
2 seconds off
Slave Arm Rev Counter
Error
•
•
•
Connections to Master Inputs
Master Arm Power Cable
Rev Counter
32
Generation 3 Visual Feedback
Symptom
Diagnosis
Check:
Status (clear)
1 blink
Cycle Terminal
Shorted
Disconnect the push button, keypad, intercom keypad, or any other accessory
wired to this terminal. Try the remote. If the remote works, then the problem is
the accessory.
Status (clear)
2 blinks
Safety Terminal
Shorted
Disconnect the loop detector, photo beam, or any other accessory wired to this
terminal. Try the remote. If the remote works, the problem is the accessory.
Status (clear)
3 blinks
Exit Terminal
Shorted
Disconnect exit wand, loop detector, photo beam, Knox box, or any other accessory
wired to this terminal. Try remote. If the remote works, the problem is the
accessory.
Status (clear)
4 blinks
Shadow Terminal Disconnect the loop detector, photo beam, or any other accessory wired to this
Shorted
terminal. Try remote. If the remote works, the problem is the accessory.
Status (clear)
5 blinks
Close Edge
Terminal Shorted
Disconnect the edge sensor, photo beam, or any other accessory wired to this
terminal. Try the remote. If the remote works, the problem is the accessory.
Status (clear)
6 blinks
Open Edge
Terminal Shorted
Disconnect edge sensor, photo beam, or any other accessory wired to this terminal.
Try the remote. If the remote works, the problem is the accessory.
RF (yellow)
Flickers
Receiving 318
MHz RF
Normal operation when remote or wireless keypad is used.
RF (yellow)
OFF
No 318 MHz RF
Received
Power (green)
ON
AC or Solar
Power Present
Power (green)
OFF
No AC or Solar
Power
•
•
•
•
Battery in Remote
Program Remote
Antenna Receiver Connections
Antenna Receiver
Normal Operation
Transformer:
• Breaker or GFI
• Power at AC outlet.
• Output of Transformer.
• Voltage on wire at 18 VAC Input
Solar:
•
•
•
•
•
Solar Panel Wires Reversed
Weather
Solar Panel Placement
Output of Solar Panel
Voltage on wire at Solar Input
Charge (red)
ON
Fast Charging
Mode
Battery Voltage should be ~14.8 VDC when connected to the circuit board
Charge (red)
Fast Blinking
Soak Charging
Mode
Battery Voltage should be ~14.1 VDC when connected to the circuit board
Charge (red)
Slow Blinking
Float Charge
Battery Voltage should be ~13.8 VDC when connected to the circuit board
Charge (red)
OFF
Battery Not
Being Charged
AC power
Transformer
Solar Panel – Check Weather
Charging Circuit
33
®
PROFESSIONAL ACCESS SYSTEMS
The GTO, Inc. Technical Service Department is open
Monday – Friday 8:00 A.M. – 7:00 P.M. (Eastern Time)
Telephone (800) 543-1236
Telephone (850) 575-4144
Fax (850) 575-8950 • Web site: www.gtopro.com
34
VOLTAGE RATINGS
18 Vac Transformer____________________________18.0 to 22.0 Vac, 2200mA
10 W Solar panel (single)_______________________18.0 to 22.0 Vdc 600 mA
measure voltage at panel and control box.
12 V, 7 amp hour Battery_ ______________________12.0 to 13.5 Vdc 7.0 Ah
or Two 12V, 7 amp hour Batteries if using solar power
Charging circuit ______________________________12.0 to 14.8 Vdc
measure voltage with battery connected
Repair Service
If your GTO/PRO® 4000XL/4200XL Gate Operator(s) are not operating properly, please follow the steps below:
1. First use the procedures found in the Troubleshooting Guide (see page 34).
2. If you are unable to solve the problem, call the GTO Service Department at (800) 543-1236, or (850) 575-4144.
Refer to the serial number (located on the right side of the control box) and date of purchase when calling for assistance.
3. If repair or replacement of your gate operator is necessary, the Service Department will assign a Return Goods Authorization (RGA) number to you.
4. Securely pack the component(s) authorized for return to the factory. Include a copy of your sales reciept for the purchase of the product(s). Write the RGA number issued to you on the outside of the package in LARGE BOLD PRINT.
Ship the package(s) freight prepaid to: GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA 32303.
NOTE: Products returned to GTO without a Return Goods Authorization (RGA) number in LARGE
BOLD PRINT on the outside of the package WILL NOT be accepted. Also, items returned to GTO freight
collect WILL NOT be accepted.
®
PROFESSIONAL ACCESS SYSTEMS
Fax (850) 575-8950 • Web site: www.gtopro.com
E-Mail: [email protected]
GTO, Inc.
3121 Hartsfield Road • Tallahassee, Florida, USA 32303 • (850) 575-0176 • Fax (850) 575-8912 •
Web site www.gtopro.com
35
Column Installation Information
IF THIS OPERATOR WILL BE USED WITH GATES THAT ARE MOUNTED ON
MASONRY, BRICK, OR ROCK (etc.) COLUMNS:
READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING
A.
The simplest solution is to install the operator in a push-to-open configuration. The minimum clearance is
easier to achieve and clearance is no longer a problem, since the operator will be pushing the gate away from
the column instead of pulling it toward the column. It is recommended that you place a steel plate between the
operator mounting brackets and masonry surface for additional strength.
B.
If a push-to-open installation is impossible due to traffic hazards, terrain, etc., another option is to re-hang the
gate. You may hang it on a post, either in the center of the column or at the back corner, or move the gate to the
back corner of the columns.
C.
The most difficult solution is to cut a notch in the column to accommodate the operator and power cable. This
job is NOT for the inexperienced!
Column Mount Example
(A + B can not exceed 19 inches)
Example: If A is 2" then B can not exceed 17"
A
Pivot Bracket
B
Gate
Column
Hinge
36
ACCESSORIES
Solar Panel (FM123), (FM122)
The Solar Panel is a 10 watt solar powered battery charger for use with the all GTO/PRO DC gate
operator systems. Particularly suited for remote installations, each Solar Panel comes with tubular
steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire
for additional wire). The GTO/PRO® control board has clearly labeled terminal connections for easy
installation of the Solar Panel. Installation in some regions of the world will require multiple solar
panels for adequate charging power. Solar Panel (FM122) is a 5 watt solar powered battery
charger with all the same features as (FM123).
Push Button Control (RB101)
Unlit doorbell button for remote entry or exit control. Wires directly to the control board and uses 16
gauge multi-stranded, dual conductor low voltage wire (sold separately).
Pin Lock (FM345)
The Pin Lock substitutes for the clevis pin at the front end of the GTO/PRO® 4000XL gate operator.
Helps prevent theft of the operator from the gate, while allowing quick release of the operator.
Key Chain Two Button Transmitter (RB742)
The Key Chain Mini Transmitter is a miniature version of the GTO/PRO® entry transmitter and has the
same adjustable code settings. 12 Volt battery included.
Single Button Transmitter (RB741)
The GTO/PRO® entry transmitter, with adjustable code settings, is standard equipment with all GTO/
PRO® systems. 12 Volt battery included.
1
2
3
4
5
6
7
8
9
0
Digital Keypad (F310)
The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can be
programmed to use up to 25 different personal identification number (PIN) codes. Each code is face
programmable with additional security features built in. Wired installations require 16 gauge, low
voltage, multi-stranded, dual conductor, direct burial wire (sold separately). Requires 3 AA batteries
(not included) or hardwiring to battery in gate opener.
Mounting Post (F100) - In Ground
This black powder coated pedestal is designed to provide convenient access to your keypad, wireless
intercom, or other access control device from your vehicle. With its break down design it is easy to
install and works well in most standard applications. Surface Mount Flanges (F102) and Extensions
(F103) for added height are available.
GTO/PRO 50' Exit Wand (FM139), 100' Exit Wand (FM140), 150' Exit Wand (FM141)
The GTO/PRO® Exit Wand is designed for residential and agricultural applications and is compatible
with all GTO/PRO® automatic gate operator models. The wand is an electromagnetic sensor, which
offers 'hands free' operation of the GTO/PRO® Gate Operators with a 12 ft. radius of detection of
vehicles in motion.
IC
MAT
AUTO LOCK
GATE
Automatic Gate Lock Pull-to-Open (FM144)
A MUST for added security. Solenoid driven, with a steel housing. Unlocks and locks automatically as
gates open and close. Used with GTO/PRO® DC swing gate operating systems for maximum stability
and security. Comes with a keyed manual release. Recommended for gates over 8 ft. long. Ideal for
animal enclosures or high wind areas.
37
ACCESSORIES
Wireless Entry Intercom / Keypad (F3100MBC)
Allows owner to screen guest at the gate before allowing access to the property. Keypad also allows owner
to give up to 25 programmable entry codes to family, friends or approved delivery personnel. Codes can be
permanent of temporary. Can be wireless up to 500 feet or hard wired up to 1000 feet. Additional base stations
available (F3101MBC).
Replacement Battery (RB500)
Standard 12 volt, 7.0 amp-hour, maintenance-free battery for the GTO/PRO® 2500, GTO/PRO® 2000XL,
GTO/PRO® 3000XL, GTO/PRO® 4000XL gate operator systems. This is the only battery approved for use
with the GTO/PRO® gate operator systems. Life expectancy is 3-5 years.
Low Voltage Wire (RB509)
The 16 gauge, multi-stranded, dual conductor Low Voltage Wire is for connecting the AC powered
transformer, or the Solar Panel to the control board. Also used for the connection of accessories, such as locks,
keypads, push buttons and other wired control devices. This specially designed wire is UV treated, PVC coated
and ready for direct burial. Available in 50, 100, 250, 500 and 1000 foot rolls.
12" Push to Open Bracket (R4KPTO)
An optional longer Post Pivot Bracket for push-to-open installations that need a greater distance to achieve the
safe gate and gate operator clearance (2 inches). Order two 12" PTO brackets for conversion of a dual swing gate
installation.
Column Mount Lock Receiver (433IH)
For mounting the Automatic Gate Lock on brick columns, walls, or for other applications with limited space
between gate and post.
Replacement Transformer (RB570)
Standard 18 volt, 2200 mA, AC transformer for maintaining the battery included with the GTO/PRO® 4000XL gate
operator. This is the only transformer approved for use with the GTO/PRO® 4000XL gate operator systems.
Garage Door Receiver (RB709U)
The Garage Door Receiver allows you to use the same GTO/PRO® entry transmitter (see Dual Transmitter) to
operate your gate operator and your garage door operator. Compatible with most garage door operators.
If you have a question about GTO/PRO accessories
just call 1-800-543-GATE!
The contents of all material available on this installation manual are copyrighted by GTO, Inc. (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced,
downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO. Any reprinting of GTO publications is by permission only. Copyright
infringement is a violation of federal law.
GTO®, GTO/PRO®, Bulldog® are registered trademarks of GTO, Inc. Professional Access Systems™ is a trademark of GTO, Inc. and are the exclusive property of GTO, Inc. (“GTO”).
All rights are reserved by GTO, and these marks may not be used, in any for without the prior, written permission of GTO.
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement