15stsole_미주 - Marlow Hunter
Safety Instructions
FCC Information
This equipment has been tested and found to comply with limits for a class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment can generates, uses, and radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful inteference to radio Communications.
However, there is no guarantee that interference will not occur in a particular
Notes & Descriptions
installation.
To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind
If this equipment does cause unacceptable interference to radio and
when installing, using and maintaining your TV.
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
Warning : If you manipulate against the notice, it may cause serious injury or death to user.
more of the following measures.
Reorient or relocate the receiving antenna.
Caution : If you manipulate against the notice, it may cause slight injury to user or appliance.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
Please recycle to preserve environment.
which the receiver is connected.
Consult the dealer or an experienced Radio/ TV technician for help.
Caution
Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Ver 2.00NSO
EN 2 15 TFT-LCD TV
PAL/SECAM 3
Warning
When moving it, do not apply any forces on the set.
Disconnect the power cable and signal cable connected to the product in case
of thunder or lightning.
Do not attempt to disassemble, repair or change the product.
Whenever you need to repair, adjust or check it, refer servicing to qualified
Do not attempt to touch its power cord with wet hands.
service personnel.
If any electric pin is wet or dusty, remove the moisture or dust first before use.
Do not directly spray water or rub it with inflammable substances (thinner or
It is recommended to pull out the power cord unless you use it for a long time.
benzene) when cleaning it.
Damaged power cord, plug or unfitted outlet may be very dangerous.
Do not wet or penetrate water over/into the set.
When cleaning the LCD surface, disconnect the power and use a piece of
Do not install the set close to any heating sources.
Do not place heavy articles on it or step on the product.
The product should be installed on a clean and dry place.
smooth cloth against any scratches on it. Never use wet cloth.
Caution
Make sure to pull out the power cord when cleaning or removing the product.
Ventilation should be always open and the set should be installed in a wellWhen you detect any smog, unusual noise or smell, just disconnect the electric
power and refer servicing to qualified service personnel.
Do not place any bowl with water, beverage, can or other liquid products on it.
ventilated and wide enough place (a minimum distance away from a wall 10cm
or more).
Do not install the set in a place directly exposed to sunlight.
Do not use or place any combustible sprayer or inflammable substances close
to the product.
Do not arrange the power cord close to any heating devices/sources.
Install the outdoor antenna for the set far away from high voltage cables.
EN 4 15 TFT-LCD TV
PAL/SECAM 5
Available Temperature & Humidity
Operating Temperature
0~40˚C
Storage Temperature
-10~50˚C
Operating Humidity
10~60% RH
Storage Humidity
10~90% RH
For non-active pixel of LCD :
There may be red spots, green spots, blue spots and black spots on the screen. This is a
characteristic of liquid crystal panels and is not a problem. The liquid crystal panel is built with very
high precision technology giving you fine picture details. Occasionally, a few non-active pixel may
appear on the screen as a fixed point of red, green, blue or black. Please note this does not affect
the performance of your LCD.
When used as a PC monitor :
Optimal Resolution: 1024 768 @ 60Hz.
NOTE :
If the same pattern is continuously displayed on the TV/Monitor for a long period of time, it will
result in image "sticking" to the screen. The marking or retained image on the LCD panel results
from fixed image use is not an operating defect. As such is not covered by warranty. This product
is not designed to display fixed image patterns for extended period of time.
EN 6 15 TFT-LCD TV
PAL/SECAM 7
Contents
CHAPTER 1.
Before Use
12
Using Menus of Picture,
Sound and Others
1-2. Panels
13
4-1. Setting Picture Mode
42
1-3. Remote Control
16
4-2. Setting Sound Mode
44
1-4. Menu Configuration
18
4-3. Setting Option
45
1-5. Jog Shuttle Button
20
1-6. Inserting the Batteries in the Remote Control
21
1-1. Accessories
CHAPTER 4.
CHAPTER 5.
CHAPTER 2.
CHAPTER 3.
EN 8 15 TFT-LCD TV
Connection
Using PC MENU
5-1. Auto Adjustment
48
5-2. Setting Picture
49
2-1. Connecting Power
24
5-3. Setting Sound
50
2-2. Connecting TV Antenna
24
5-4. Setting Option
51
2-3. Connecting PC
25
5-5. Setting Color Temperature
52
2-4. Connecting HDTV
25
2-5. Connecting DVD
26
2-6. Connecting VIDEO / S-VIDEO
26
2-7. Connecting Headphone (Speaker)
27
CHAPTER 6.
Specifications
6-1. Dimensions
54
6-2. Specifications
55
Using TV Menus
CHAPTER 7.
Services & Others
3-1. Watching TV
30
3-2. Channel Search
33
7-1. Troubleshooting
58
3-3. Fine Tune
34
7-2. Concerning Services
60
3-4. Add/Remove Channel
35
3-5. Channel Swap
36
3-6. Change TV Channel Mode
37
3-7. Closed Caption
38
3-8. V-chip Function
39
PAL/SECAM 9
CHAPTER 1
Before use
1-1. Accessories
1-2. Panels
1-3. Remote Control
1-4. Menu Configuration
1-5. Jog Shuttle Button
1-6. Inserting the Batteries in the Remote Control
EN 10 15 TFT-LCD TV
PAL/SECAM 11
1-1. Accessories
1-2. Panels
Please make sure the following items are included with your LCD TV.
1) Front Panels
If any items are missing, contact your dealer.
AAA-type battery( 2)
RF Cable
-
Power Cord
-
DC Adaptor
-
Remote Control
Power/Menu
-
Power-On/Off
Channel Button
-
AUTO / Move above Menu
Sound Cont.
-
SOURCE / Move under Menu
Remote Control Sensor
-
Exit Menu
LED
-
Load Menu
Auto button operates as auto adjustment function when it’s input singnal is PC.
User’s Manual
Power button is jog shuttle type button and it operates different functions by pushing it
to Up/Down/Left/Right.
EN 12 15 TFT-LCD TV
PAL/SECAM 13
2) Rear Panels
3) Side Panels
Audio Input (L, R)
S-Video Input
Power Input
Video Input
PC Input
Audio (PC Input/Headphone Output)
TV Antenna Input
EN 14 15 TFT-LCD TV
PAL/SECAM 15
1-3. Remote Control
Functions by remote control buttons
Button
Function
Button
Function
POWER
Power On/Off
MUTE
Sound off Temporarily
0~9
Numeric Buttons.
- / --(+100)
Select channels over 100
Power On/Off
PRE
Previous Channel
CH UP/DOWN
Move TV Channels
Sound off Temporarily
VOL +/-
Control Volume
Channel Selection Button
SOURCE( / )
Input Source selection Botton (PC S-Video Video Full SCART TV Half SCART)
PC
PC Input
TV
TV Input
PM
Control Picture Mode
SM
Not available
MENU
Displays the MENU On Screen
DUAL I/II (MTS)
Not available
ON SCREEN
Display screen status
SCALE
Control Picture Scale
TV & Input Source Selection Button
Not available
Control Picture Mode
Channel & Volume Control Button
Menu Control Button
Not available
/
/
EXIT
Exit Main / Sub MENU
MENU settings (Move MENU up and down / Move MENU left and right / MENU Confirmation)
TV Functions & Teletext Menu Button
TELETEXT
Not available
Not available
MEM
Add / Remove a TV CH
SCREEN
Not available
Not available
SLEEP
Sleep Timer setting
LIST
Not available
HISTORY
Not available
DTV
Not available
SUBTI
Not available
MENU
Not available
EPG
Not available
TV/RADIO
Not available
PIP
Not available
The remote control provided operates up to 7m from the optical receive part within Left/Right
30 degrees.
EN 16 15 TFT-LCD TV
PAL/SECAM 17
1-4. MENU Configuration
2) Using Remote Control
Most functions of the TV set can be controlled by MENU and selection buttons on the
remote control, so learning how to operate them would be convenient for you.
Press MENU button to display main menu.
1) Menu Configuration
Press Menu control button (
/ ) to move to sub menu of a
selected main menu.
Main Menu
Sub Menu
Settings
To move among menus, use Menu control button (
/
).
To change a selected menu setting, use Menu control button ( / ).
Press EXIT button to return from sub menu to main menu or
from main menu to menu removal.
EN 18 15 TFT-LCD TV
PAL/SECAM 19
1-5. JOG Shuttle Button
1-6. Inserting the Batteries in the
Remote Control
Push MENU button right to display main menu.
Remove the cover of the remote control.
Check the polarity of batteries and insert them in right directions.
Push it right again to display sub menu.
Replace the cover.
Available batteries : 2 DC 1.5V AAA-type batteries
Push MENU button left to return to main menu.
Since incorrect insertion of batteries may cause breakage, leakage or injuries, check
the polarities before the insertion.
Separate and collect used batteries for the protection of environment.
Do not use alkaline and manganese batteries together.
Push it left again to clear menu.
Push the button up and down to move among menus.
If pushing it downward when menu is not display, it changes input signals.
EN 20 15 TFT-LCD TV
PAL/SECAM 21
CHAPTER 2
Connection
2-1. Connecting Power
2-2. Connecting TV Antenna
2-3. Connecting PC
2-4. Connecting HDTV
2-5. Connecting DVD
2-6. Connecting VIDEO / S-VIDEO
2-7. Connecting Headphone (Speaker)
EN 22 15 TFT-LCD TV
PAL/SECAM 23
2-1. Connecting Power
2-3. Connecting PC
The product automatically adjusts voltage.
Power Cable should be firmly connected to an outlet or DC adaptor in order not to
be pulled out or shake.
2-2. Connecting TV Antenna
When round cable (75Ω coaxial cable) is used, copper part of the cable should not
be bent.
<Input>
<Output>
Connect D-Sub Cable to D-Sub port on the TV and PC.
Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC
Audio Input Port of the TV (stereo jack).
TV antenna
TV Wall-outlet
RF cable
Connecting RF
cable
2-4. Connecting HDTV
copper wire
Antenna converter
Connecting
feeder cable
feeder cable
TV Wall-outlet
Digital TV Broadcasting Receiver
Pb Y Pr
L
R
Pb
Y
Pr
L
R
Cautions
1. When an outdoor antenna is used, it is recommended for a qualified technician to install it.
2. For weak radio wave, signal amplifier (purchased separately) is recommended for use.
<Input>
<Output>
Connect Component Cable (not included) to HDTV Connection ports of TV (Pb Y
Pr) and DTV Receiver.
Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver.
Cables should be connected to ports of the same colors.
EN 24 15 TFT-LCD TV
PAL/SECAM 25
2-5. Connecting DVD
Cables should be connected to ports of the same colors.
Audio signals of S-VIDEO should be used with external audio signal cables.
S-VIDEO signal secures better picture quality than composite video signal.
DVD Playera
R
2-7. Connecting Headphone(speaker)
L
Pr
Pb
Y
Pr
L
R
Y
Pb
<Input>
<Output>
Connect Component Cable (not included) to Component ports of TV and DVD
player. VCR, Set-Top box or camcorder.
<Output>
2-6. Connecting VIDEO/S-VIDEO Input
Video & DVD Player
Connect Headphone (not included) to the Headphone output port of the TV.
If possible, use headphones of 8ohms impedance. Otherwise output volume may
L
be too low or too loud.
R
In case of connecting to speakers, connect speakers with amps. If connected with
Audio
Video
S-VIDEO
speakers without amps, the output volume may be low.
<Input>
<Output>
Connect Video/Audio Cable (not included) and S-VIDEO Cable to Video port of TV
and camcorder, game machines, VCR, DVD player or Set-Top box.
EN 26 15 TFT-LCD TV
PAL/SECAM 27
CHAPTER 3
Using TV Menus
3-1. Watching TV
3-2. Channel Search
3-3. Fine Tune
3-4. Add/Remove Channel
3-5. Channel Swap
3-6. Change TV Channel Mode
3-7. Closed Caption
3-8. V-chip Function
EN 28 15 TFT-LCD TV
PAL/SECAM 29
3-1. Watching TV
3) Channel Selection
Press CH button on the remote control to change channels.
1) Precautions in the initial installation
Press numeric buttons (0~9) to go to a channel directly.
Press CH buttons (
) on the TV set to change TV channel up or down.
Check whether TV antenna cable is properly connected.
Check input voltage then connect power cord and adaptor to TV.
TV is now ready to be turned on.
2) Turning on TV
Press the Power button on either the TV set or the remote control.
Channel button on the remote control
Channel button on the TV set
Each pressing the button turns on or off the set.
4) Move to Previous Channel
When pressing the PRE button on the remote
control, it moves back to a previous channel.
Previous Channel Button
Power Button on Remote Control
Power Button on the TV Set
5) Volume Control
Increase/decrease volume by pressing VOL button on the remote control.
Press VOL button ( + / - ) on the TV set to control the volume.
Volume Button on the remote control
EN 30 15 TFT-LCD TV
Volume Button on the TV Set
PAL/SECAM 31
3-2. Channel Search
6) Mute
Press
MUTE
button on the remote control to
turn off the sound.
When using the TV for the first time, or after reconnecting it due to power failure or
other reasons, channels should be searched and registered again.
Press it again to turn the sound back on or press
volume buttons.
- Press
MENU
button on the remote control.
MUTE button on the remote control
- Once you move to Start by using
button on the remote control, it starts channel
search.
- To stop channel search, repress
7) Checking the present broadcasting information
Press
ON SCREEN
button on the remote control
MENU
button on the remote control.
- If you stop it during channel search, it stores the currently searched channels only.
- Also, it can be set in OSD by using JOG button.
to display the information on the screen.
Press it again to remove the information except
input source automatically.
Broadcasting Info Button
EN 32 15 TFT-LCD TV
Press it again to remove all information.
PAL/SECAM 33
3-3. Fine Tune
3-4. Add/Remove Channel
If a searched channel is unclear or the sound is not working properly, use Fine Tune
You may add or remove a channel as your need.
function to adjust.
- Channel can be added or removed by pressing numeric buttons(0~9) or CH button.
- Press
MENU button and move to <CH Fine Tune> menu.
- Set the best status with
- To stop channel search, repress
button on the remote control.
MENU
button on the remote control.
- Once the setting is complete, exit from menu.
- Press MEM button on the remote control.
- In case of adding a channel by using
button on the remote
control, move to Add.
- Once the setting is complete, press MEM button again.
- Also, it can be set in OSD menu by using JOG button.
EN 34 15 TFT-LCD TV
PAL/SECAM 35
3-5. Channel Swap
3-6. Change TV Channel Mode
For frequently watched channels, you can store and swap between those channels.
Please choose your TV input type by selecting either Air or Cable.
If set as Air, some cable broadcast stations will not be displayed.
- Move to a channel to change.
- Press MENU button on the remote control and move to <CH Swap> menu.
- Press MENU button on the remote control and move to <CH Mode> menu.
- Set both channels that you are watching and want to swap.
- Set the CH Mode between Air & Cable by using
- Change the default and escape the menu.
button on the
remote control.
- Once the setting is complete, press MENU button.
- Also, it can be set in OSD menu by using JOG button.
EN 36 15 TFT-LCD TV
PAL/SECAM 37
3-7. Closed Caption
3-8. V-Chip Function
This function works only with caption broadcast or other CC marked video tape and
This function deals with MPAA rating of TV broadcast and other media.
DVD title.
It works only with V-Chip function broadcast and media.
Set the function in the SETUP menu.
Caption can be set only by using the remote control.
- Press MENU button on the remote control and move to <V-Chip> menu.
- Set the V-Chip menu by using button on the remote control.
- Select a TV station, video tape or DVD title
- Press MENU
button on the remote control and move to <Closed
Caption> menu.
- Set Caption broadcast type by using
button on the remote control.
- Also, it can be set in OSD menu by using JOG button.
Default V-Chip PIN is 0000.
Please change PIN as yours when you install.
- Press
button and enter Password.
- Press pin number using the remote control.
- A number can be deleted with left volume button when using it.
- Set V-Chip function by using
EN 38 15 TFT-LCD TV
button on the remote control.
PAL/SECAM 39
- Move to TV Guideline or MPAA Rating by using
button on the remote control.
CHAPTER 4
- Move to the position which you want to make channel blocking and press MENU
button for setting.
Using Menus of
Picture, Sound
and Others
- Press it again for cancellation.
4-1. Setting Picture Mode
4-2. Setting Sound Mode
4-3. Setting Option
- Escape the menu pressing EXIT.
- V-chip function can be set up only by the remote control.
EN 40 15 TFT-LCD TV
PAL/SECAM 41
4-1. Setting Picture Mode
2) Mode : Standard - Soft - Dynamic - User
- Press PM button on the remote control.
1) Image Scale : Full - Wide
- Set a picture mode by using PM button on the remote control.
You can set the screen’s suitable image scale of TV or Video input signals and view
them accordingly.
Standard : Standard picture mode.
Soft : It displays a picture softly as a whole and is better for watching movie or
- Press
SCALE
button on the remote control.
Full : Show a screen in the full LCD Panel.
Wide : Show a screen in the 16:9 Wide screen size.
- Also, it can be set in OSD menu by using JOG button.
EN 42 15 TFT-LCD TV
regular cable TV.
Dynamic : This mode is suitable for watching sports or movie.
User : It is a picture mode customized by a user.
- Also, it can be set in OSD menu by using JOG button.
PAL/SECAM 43
3) Brightness : Adjust screen brightness
4) Contrast : Adjust screen contrast
5) Color : Adjust screen color
4-3. Setting Option
- Press
MENU
button on the remote control to move to Main Menu.
- Change the settings by using
/
button on the remote
control.
6) Tint : Adjust screen tint
7) Sharpness : Adjust screen sharpness
4-2. Setting Sound Mode
Volume : Adjust volume
Bass : Adjust bass
Treble : Adjust treble
Balance : Adjust balance of left & right speaker
Sleep Timer
- Press
SLEEP
button on the remote control.
- Sleep timer can be set up to 180 minutes.
Menu Timeout : It can be adjusted to display OSD Menu between 5 ~ 60 seconds.
Menu Language : Change a language to display OSD.
Factory Reset : Reset all the OSD control settings back to the factory default
setting.
Version : It shows the product version.
EN 44 15 TFT-LCD TV
PAL/SECAM 45
CHAPTER 5
Using PC MENU
5-1. Auto Adjustment
5-2. Setting Picture
5-3. Setting Sound
5-4. Setting Option
5-5. Setting Color Temperature
EN 46 15 TFT-LCD TV
PAL/SECAM 47
5-1. Auto Adjustment
The Standard Signal Modes for PC Monitor
Resolution
When the set is connected to a PC, the MODE should be set as PC RGB Mode.
- Press
AUTO
button on the remote control synchronize the TV set
with the PC.
- When it is used as PC monitor
Optimal Resolution : 1024 x 768 @ 60Hz
(H
V)
Vertical Frequency Horizontal Frequency Clock Frequency
(kHz)
(Hz)
(MHz)
Polarity
(Vert./Hor.)
640
480
31.469
59.94
25.175
-/-
640
480
37.861
72.809
31.5
-/-
640
480
37.5
75
31.5
-/-
720
400
31.469
70.087
28.322
-/+
800
600
35.156
56.250
36
+/+
800
600
37.879
60.317
40
+/+
800
600
48.077
72.188
50
+/+
800
600
46.875
75
49.5
+/+
-/-
1024
768(Optimal)
48.363
60.069
65
1024
768
56.476
70.069
75
-/-
1024
768
60.023
75.029
78.75
+/+
When you use it as a PC monitor, depending on signals of a PC, it may not display
picture normally even though it is set for standard mode resolution.
5-2. Setting Picture
- Brightness : Adjust screen brightness
- Picture may not be displayed properly in any resolution other than the optimal
resolution.
- Even though it is automatically adjusted, it may display picture depending on signals
from a PC and in this case, It is then recomended to use Auto Adjustment function.
- Also, it can be set in OSD menu by using JOG button.
- Contrast : Adjust screen contrast
- Phase : In case picture is not optimally set after auto-adjustment, use Phase function.
- H. Size : Adjust the Size of the screen.
- H. Position : Adjust the H position of the screen.
- V. Position : Adjust the V position of the screen.
- Auto Adjustment : Automatically resets its all settings to optimize the picture quality.
EN 48 15 TFT-LCD TV
PAL/SECAM 49
5-3. Setting Sound
5-4. Setting Option.
- Volume : Adjust volume
- Press
- Bass : Adjust bass
MENU
button on the remote control to move to Main
Menu.
- Treble : Adjust treble
- Change the settings by using
- Balance : Adjust balance of left & right speaker
/
button on the remote
control.
Sleep Timer
- Press SLEEP button on the remote control.
- Sleep timer can be set up to 180 minutes.
Menu Timeout : It can be adjusted to display OSD Menu between 5 ~ 60 seconds.
Menu Language : Change a language to display OSD.
Factory Reset : Reset all the OSD control settings back to the factory setting status.
Version : It shows the product version.
EN 50 15 TFT-LCD TV
PAL/SECAM 51
5-5. Setting Color Temperature
CHAPTER 6
- Press MENU button on the remote control and move to <Color Temp> menu .
- Set the value between 5500, 7300, 9300 or you can set as your preference in USER.
Specifications
6-1. Dimensions
6-2. Specifications
EN 52 15 TFT-LCD TV
PAL/SECAM 53
6-1.Dimentions
6-2. Specifications
Dimensions, design and all specifications are subject to change without any prior
notice.
Product Name
LCD Panel
35.6mm
15” TFT-LCD TV
Type
Amorphos Silicon TFT-LCD
Size
15” (diagonal length)
Pixel Pitch
0.297 mm x 0.297 mm
Contrast Ratio
500 : 1 (Typ.)
Brightness
450 cd /
Actual Display Size
304.1mm (H) x 228.1mm (V)
356mm
17.5mm
323mm
323mm
LVDS
NTSC-M Type
Audio Output
MAX 3W x 2 / Stereo
Power
Power Consumption
Energy Saving Mode
EN 54 15 TFT-LCD TV
L/R : 130° U/D : 100°
Interface
TV Broadcasting System
PC Monitor
Weight : approx. 4.5kg (before packing) / approx. 5.9kg (after packing)
Viewing Angle
Horizontal Frequency
30 ~ 61 KHz
Vertical Frequency
60~ 75 Hz
Colors
16M colors
Max. Resolution
XGA : 1024 (H) x 768 (V)
Adaptor Input
AC 100V~240V, 50~60Hz
Adaptor Output
DC 12 V
In-Operation
< 40W
Power-Saving Mode/OFF
< 5W
VESA DPMS
PAL/SECAM 55
CHAPTER 7
Service & Others
7-1. Troubleshooting
7-2. Concerning Services
EN 56 15 TFT-LCD TV
PAL/SECAM 57
7-1. Troubleshooting
2) PC Monitor-related Troubles
If the TV seems to have a problem, please check the followings first.
No image on the monitor
If you still have the same symptoms even after taking the following actions,
Check whether the D-Sub cable is firmly connected to the TV and a PC.
contactyour local dealer or nearest service centre.
Check whether a graphic card is correctly inserted into the slot.
Check whether the Power of a PC and the TV is on.
1) TV-related Troubles
Checck whether a graphic card or mode is set appropriately on a PC.
Referring to the Standard Signal Mode for PC Monitor in the previous chapter,
Unclear display or noisy sound
Check whether TV antenna is correctly connected.
change graphic mode.
Check whether D-Sub cable pins are not inserted or bent.
Broadcasting may not be good in an area with bad reception or far away from a
station/network.
No Power
Check whether the power cord is normally inserted and reconnect it.
No image
Pull out the power cord from wall outlet and reconnect it in 10~20 minutes.
Check whether power is connected correctly. And press the POWER button.
LED Lamp turns off in red and it shows no image
Black background only
Check whether the graphic cable is connected to theTV and a PC.
Check whether the mode is set as PC monitor or Video/S-Video Input, not TV mode.
Check whether a computer is in power-saving mode and attempt to operate
keyboard and mouse.
Strips and shaking display
It may be interrupted by neighboring radio waves (please check any wireless phone,
hair drier, electric drilling machine and etc)
Execute fine tuning for manual adjustment.
Unstable or unfocused image or trembling
Check whether the D-Sub cable is connected to the TV and a PC.
If a PC’s display mode is changed, the screen needs readjusting, so you need to
use Auto Adjustment or Picture Adjustment.
Can’t receive a specific channel
Check whether Channel Setting is normally set.
Try to rotate an antenna’s direction.
Picture plays without sound
VOL
whether it is set as an appropriate refresh rate. If letters look distorted, change the
refresh rate to 60Hz.
Abnormal image scale
Try to press MUTE button.
Volume up by using
Check whether the TV and your graphic card are compatible each other and
By using vertical/horizontal position in Picture Adjustment Menus, adjust the
button.
position.
Try to execute Auto Adjustment function.
EN 58 15 TFT-LCD TV
PAL/SECAM 59
7-2. Concerning Services
In one of the following cases, warranty will be void.
1) Malfunctions resulting from inserting of foreign substances (water, beverage, coffee
and etc)
2) Dropping or applying force causing damages to the product or induce malfunction.
3) Appearance damage or transformation by use of organic solutions such as thinner,
benzene and etc.
4) Malfunction due to disassemble by the user.
5) When other parts/consumption accessories (including adaptor) that are not supplied
by the manufacturer causing malfunction.
6) Supplying wrong voltage to the unit causing malfunction.
7) A repair or modification performed by an unauthorized service personnel causing
malfunction.
8) Natural disasters (lightning, fire, flood, gas, damage from sea wind, earthquake and
etc) directly cause troubles
9) Violation against the directions in the manual causing malfunction.
10) Customer’s mishandling causing malfunction.
EN 60 15 TFT-LCD TV
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement