hs gravitex plus stone chip protector

hs gravitex plus stone chip protector
HS GRAVITEX PLUS
STONE CHIP PROTECTOR
Description
GRAVITEX PLUS is a tough, hard, durable coating designed to reproduce the manufacturers
original stone chip finish. It will protect against stone chips, salt, damp and rust. GRAVITEX
PLUS will also help to deaden sound and vibrations and is, therefore, ideal for application to
panels and inside engine compartments. The high build formula will cover weld marks and
seams, often in one application.
Health & Safety Statement
FOR PROFESSIONAL USE ONLY. Read full instructions before use.
IMPORTANT: This product contains hazardous materials and therefore appropriate personal
protective equipment should always be used. Please refer to the label and consult the material
safety data sheet for full handling instructions and personal protection information. These are
available via your local stockist or via the U-POL website at WWW.U-POL.COM.
U-POL disclaim any liability where the user does not wear the recommended personal
protective equipment.
Surface Preparation &
Instructions for Use
GRAVITEX PLUS stone chip protector can be used on the following surfaces:• Suitably prepared bare metal. For overcoating aluminium, ACID #8 etch primer is
recommended.
• Original paint surfaces (with the exception of thermoplastic acrylics).
Thoroughly clean and degrease old paint surfaces with a suitable spirit wipe or thinner. Wet flat
with 400 grade paper. For bare metal use 180 grade paper. Re-clean and dry.
Application
Shake the tin before use. Apply with a clean Schutz gun or brush. Allow approximately 1015 mins. for the solvent to flash off when building a thick coat.
Thinners
GRAVITEX PLUS is supplied ready for use.
Build & Pressure
One coat of GRAVITEX PLUS will give a build of approximately 100-150 microns and a
pressure of between 2.76 - 4.82 BAR is required at the gun. Less or more pressure will give a
flatter or more rippled effect.
Drying Time
Approximately 2 hours at normal shop temperature or 30 mins. at low bake (80ºC). Drying time
is dependent on film thickness, humidity and temperature.
Over-Painting
GRAVITEX PLUS may be over-painted with most paint systems. With 2 pack acrylic paints its
can be over-painted wet on wet. For optimum gloss and protection from fading, the use of a
U.V Clear is recommended.
Issue 6/2011
1
VOC Information
As Packaged
UP0721 & UP0792
As Packaged
UP0723 & UP0793
VOC
Regulatory
432g/l
3.6lbs/gal
424g/l
3.5lbs/gal
432g/l
3.6lbs/gal
VOC Actual
423g/l
3.5lbs/gal
424g/l
3.5lbs/gal
430g/l
3.6lbs/gal
Volatiles
44.85% by weight
41.06% by weight
42.64% by weight
Exempt
Compounds
0% by
weight
2.7% by
weight
0% by
volume
2.09% by
volume
0% by
weight
0.00% by
weight
0% by
volume
0.00% by
volume
0% by
weight
0.50% by
weight
0% by
volume
0.38% by
volume
Density
1005g/l
8.4lbs/gal
1034g/l
8.6lbs/gal
1021g/l
8.5lbs/gal
Water
Product Codes
As Packaged
UP0722
UP0721 UP0722 UP0723 -
Black Color/ 1L tin.
White Color/ 1L tin.
Gray Color/ 1L tin.
UP0792 UP0793 -
Black Color / 25L drum.
Gray Color / 25L drum
U-POL US, Inc., 630 Selvaggio Dr, Suite 300, Nazareth, PA 18064
Tel: (800) 340 7824; Fax: (800) 787 5150
Email: [email protected] Website: www.u-pol.com
Issue 6/2011
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement