Gas Fryer (NG Unit)
Gas Fryer (NG Unit)
instruction
sheet
#383292
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
CAUTION
insPect contents iMMeDiAteLY AnD FiLe cLAiM With DeLiVerinG cArrier For AnY DAMAGe.
SAVE YOUR BOX AND ALL PACKING MATERIALS.
You Are resPonsiBLe For DAMAGe to Your unit iF returneD iMProPerLY PAcKeD.
Model: CLGF30-NG
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or parts, this information is required.
CLGF30-NG
Model Number
Serial Number
Date Purchased
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other
appliance.
MESURE DE SÉCURITÉ: Ne pas entreposer ni utiliser d’essence ni autres vapeurs ou liquides inflammables à proximité de cet
appareil ou de tout autre appareil.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
AVERTISSEMENT: L’installation, le réglage, la modification, la réparation ou l’entretien incorrects de cet appareil peuvent
causer des dommages matériels, des blessures ou la mort. Lire attentivement les instructions d’installation, de
fonctionnement et d’entretien avant de procéder à son installation ou entretien.
WARNING: Instructions must be posted in a prominent location. All safety precautions must be taken in the event the user
smells gas. Safety information can be obtained from your local gas supplier.
AVERTISSEMENT: Les instructions doivent être affichées dans un endroit très visible. Toutes les mesures de sécurité doivent
être prises au cas où l'utilisateur sente l'odeur de gaz. L'information de sécurité peut être obtenue de votre fournisseur local
de gaz.
CAUTION: These models are designed, built, and sold for commercial use only. If these models are positioned so the general
public can use the equipment, make sure that cautions, warnings, and operating instructions are clearly posted near each unit
so that anyone using the equipment will use it correctly and not injure themselves or harm the equipment.
ATTENTION: Ces modèles sont conçus, fabriqués, et vendus pour un usage commercial seulement. Si ces modèles sont placés
pour que le grand public puisse les utiliser, assurez-vous que les consignes d’attention, d'avertissement, et les instructions
d'utilisation soient clairement affichées près de chaque unité de sorte que n'importe quel utilisateur de l'appareil l'emploie
correctement et ne se blesse pas ou n'endommage pas l'appareil.
(continued on next page)
eG9937
revised 07/16
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: 302/653-3000 • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: 302/653-2065
eagle Foodservice equipment, eagle Mhc, specFAB, and retail Display are divisions of eagle Group. ©2016 by the eagle Group
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
GAS PRESSURE
The appliance and its individual shutoff valve (to be supplied by user) must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of ½ psi (3.45 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than ½ psi (3.45 kPa).
PRESSION DE GAZ
L'appareil et sa valve d'arrêt individuelle (doit être fournie par l'utilisateur) doivent être déconnectés de la canalisation de gaz durant tout test
de pression du système à une pression supérieure à ½ psi (3.45 kPa).
L'appareil doit être isolé du système de canalisation de gaz par la fermeture de la valve individuelle d'arrêt manuel pendant tout test de pression
du système de canalisation de gaz à pression de test égale ou inférieure à ½ psi (3.45 kPa).
WARNING: :A factory authorized agent should handle all maintenance and repair. Before doing any maintenance or repair,
contact EAGLE GROUP.
AVERTISSEMENT: Un technicien autorisé par l'usine devra effectuer tout l'entretien et les réparations. Avant de faire tout
entretien ou réparation, veuillez contacter EAGLE GROUP.
Congratulations on your purchase of this commercial cooking equipment. Eagle Group takes pride in the design and quality of
our products. When used as intended and with proper care and maintenance, you will experience years of reliable operation
from this equipment. To ensure best results, it is important that you read and follow the instructions in this manual carefully.
TABLE OF CONTENTS
ITEM
PAGE
Safety precautions . . . . . . . . . . . . . . . . . . . 3
General Installation Instructions . . . . . . . . 4
Specifications & Dimensions. . . . . . . . . . . 4
Lighting Instructions . . . . . . . . . . . . . . . . . . 5
Operating Instructions . . . . . . . . . . . . . . . . 6
Cleaning & Maintenance . . . . . . . . . . . . 7-8
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . 9
Exploded View. . . . . . . . . . . . . . . . . . . . . . 10
Replacement Parts List . . . . . . . . . . . . . . 11
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 11
(continued on next page)
2
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
LOCATION OF DATA PLATE
The data plate is located on the side panel.
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its
safe transit and delivery. If equipment is received damaged, either apparent or concealed, a claim must be made with the
delivering carrier.
A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by the carrier
representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the necessary forms.
B) Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection must be made to the
carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all contents and packaging material.
Installation and should be performed by a qualified installer who thoroughly read, understands and follows these instruction.
If you have questions concerning the installation, operation, maintenance or service of this product, contact the factory.
SAFETY PRECAUTIONS
DANGER: This symbol warns of imminent hazard which will result in serious injury or death.
DANGER: Ce symbole avertit d'un risque imminent qui a comme conséquence des blessures graves ou la mort.
WARNING: This symbol refers to a potential hazard or unsafe practice, which could result in serious injury or death.
AVERTISSEMENT: Ce symbole désigne un possible danger ou une pratique dangereuse qui pourrait entraîner des blessures
graves, ou la mort.
CAUTION: This symbol refers to a potential hazard or unsafe practice, which could result in minor or moderate injury or product
or property damage.
ATTENTION: Ce symbole désigne un possible risque ou une pratique dangereuse , qui pourrait avoir comme conséquence des
blessures, ou des dommages mineurs ou modérés au produit ou au matériel.
NOTICE: This symbol refers to information that needs special attention or must be fully understood even though not dangerous.
AVIS: Ce symbole désigne l'information qui a besoin d'une attention particulière ou qui doit être entièrement comprise bien
que non dangereuse.
NOTICE: This product is intended for commercial use only. Not for household use.
AVIS: Ce produit est prévu pour un usage commercial seulement. Ce produit n'est pas destiné à un usage domestique.
NOTICE: Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association, Inc.,
states in its NFPA96 latest edition that local codes are “Authority Having Jurisdiction” when it comes to requirement for
installation of equipment. Therefore, installation should comply with all local codes.
AVIS: Les codes locaux concernant l'installation changent considérablement d'un secteur à l'autre. National Fire Protection
Association, Inc., déclare dans sa dernière édition NFPA96 que les codes locaux sont "Autorité ayant la juridiction" quand il
s'agit des conditions pour l'installation d’appareils. Par conséquent, l'installation doit être conforme à tous les codes locaux.
(continued on next page)
3
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
GENERAL INSTALLATION INSTRUCTIONS
Unit installation must conform to the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the National Gas Installation Code, CSAB149.1, or the Propane Installation Code, CSA-B149.2 as applicable and in accordance with local codes.
1. Ensure gas supply and gas type as shown on unit nameplate are the same.
2. Screw legs into the permanently fastened nuts on the four corners of the unit and tighten by hand. Level the unit by turning
the adjustment screw at the bottom of each leg. Do not slide unit with legs mounted, lift if necessary to move unit.
3. Install shut-off valve (not supplied) and regulator to gas inlet. Use proper pipe thread compound. Pipe threading compound
must be resistant to the action of liquefied petroleum gases.
4. Install baffle plate in flue - see figure 1.
CAUTION: DO NOT use an open flame to check for leaks. Check all gas piping for leaks with a soap and water solution before
operating unit.
ATTENTION: NE JAMAIS employer une flamme nue pour déceler l'existence de fuites. Examinez toute la tuyauterie de gaz pour
déceler les fuites avec une solution de savon et d'eau avant de mettre en marche l'unité.
ONLY NON-COMBUSTIBLE MATERIALS CAN BE USED IN CLOSE PROXIMITY TO THIS APPLIANCE.
Combustible clearances:
6" sides (152mm); 6" rear (152mm); 4" floor (102mm)
Non-combustible clearances:
0" sides (0mm); 0" rear (0mm); 4" floor (102mm)
)J
# >2
,
Do not obstruct the flow of combustion and ventilation air, under the unit by the legs or behind the unit by the flue.
)J
# >2
,
Ne pas obstruer le flux d'entrée et de sortie d'air de combustion et de ventilation, sous l'unité par les pattes ou derrière
)J
# >2
,
l'appareil par le conduit.
Adequate clearance for air openings into the combustion
chamber
)J
# >2 is, required. Do not place objects between the bottom of the
unit and the counter top.
Un espace adéquat pour les orifices d'aération dans la chambre de combustion est nécessaire. Ne placez pas des objets entre
le fond de l'unité et le comptoir supérieur.
There must be adequate clearance for removal of the front panel. All major parts except the burners are removable thru the
front if the gas line is disconnected.
&
K
;CLGF30-NG
(>0#9<,7 <
#%
,
A7B'
#
#%
( 7 '
,
! #!( (
D !
#%
,
2A
0
!& !&
%
#*0H,
6( >>>
%
<
/ !
# 1 ,
# 1 ,
A
)
(continued on next page)
4
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
LIGHTIING INSTRUCTIONS
Fryers are furnished with a Gas Control Safety Valve. Please follow the instructions below.
Before Lighting Pilot and Burners
Fill the fat tank about 3/4" below the full line with proper frying compound before lighting pilot. The
reason for filling the tank 3/4" below the full line is that the frying compound will expand during the
preheating process.
If the frying compound expands above the full line, the frying compound may overflow out of the tank
during the cooking process. The reason for adding fry compound in fry tank before lighting the pilot
or burners is that the unit will be damaged if this is not done.
Operating Instruction:
/ .
9
<
;
=
Step 1.
Ensure this Gas Control Valve dial is at the “OFF” position.
/ .
9
< ;
=
Step 2.
Step 3.
Ensure the thermostat dial is at the “OFF” position.
0
< ;
=
E
E
!
%
0
< ;
=
E
E
!
Turn
the Gas Control Valve dial to “Pilot” position and press and hold. Press the pilot
%%
ignition button. If the unit does not light, continue pressing and holding the pilot button
and press the ignition button again. Purging air from the system may take 5–7 minutes on
% use.
first
(continued on next page)
5
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
) 0
<
;
=
E: G
!
C
,
$
!
-
4
1
4
:
L
CAUTION:
The fryer must be turned completely off
prior to draining the oil. Ensure the
thermostat and gas control valve are in
the off position and the pilot and burners
are completely extinguished.
OPERATING INSTRUCTIONS
All burners are lit from constantly burning pilots. Turning the thermostat to the desired temperature
is all that is required to put the unit in service.
Do not permit fans to blow directly at the unit. Wherever possible, avoid open windows next to the
unit's sides or back. Avoid wall type fans which create air cross-currents within a room. It is also
necessary that sufficient air should be allowed to enter the room to compensate for the amount of
air removed by any ventilating system. Otherwise, a subnormal atmospheric pressure will occur,
which will effect operation and cause undesirable working conditions.
A properly designed and installed hood will act as the heart of the ventilating system for the room
or area in which the unit is installed and will leave the unit independent of changing draft
conditions.
All valves and thermostats must be checked periodically. Consult the authorized service
representative in your area.
A planned maintenance program can ensure the safety and performance of this unit is maintained.
(continued on next page)
6
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
CLEANING
Initial Cleaning
Always clean equipment thoroughly before first use. Clean the protective oil from the bright parts and
interior of tank with an appropriate de-greasing solution.
Daily Cleaning
1. Always turn unit off and allow it to cool completely before cleaning.
2. Never clean unit by immersing it in water.
3. The frequency of cleaning should depend on the load conditions. Set a definite cleaning schedule
corresponding to how hard the kettle is used. Cleaning should be done at a least once a week.
4. Strain the frying compound into a clean container. Make sure there is no compound left in tank.
(If the tank is left empty for more than 2 minutes, shut the pilot off. If this is not done, the tank
may be damaged.)
5. Add water to the "MAX" line.
6. Add any good grade of cleaner following cleaner instructions.
7. Turn the thermostat to 75°F(dial “°F” position). Let the heating unit bring the solution to a boil.
8. Boil long enough to loosen or dissolve all varnish or carbon deposits. This should take
approximately 30 minutes.
9. Turn the unit off. Make sure pilot is turned off at this time.
10. If necessary, clean the thermostat probes using a long-handled fiber or plastic brush and mild
soap solution.
11. Rinse with clean water to remove all cleaning mixture.
12. Rinse the inside of the tank with 2 cups of vinegar.
13. Rinse with clean water until the vinegar odor is gone. The fry tank must be thoroughly rinsed
since even a trace of cleaner left inside the tank will contaminate the fry compound.
14. Dry thoroughly.
15. Cover the tank if compound will not be added until a future date.
16. Clean all exterior surfaces of unit on a regular basis with a damp cloth. Thin films of oil subjected
to frying temperatures quickly form into gummy consistency. In order to avoid these gum
formations, clean the surfaces on a regular basis.
17. To remove discolorations or oil film, a non-abrasive cleaner may be used.
CAUTION: Clean exterior of regulator at least once a month. Make sure the vent opening is open
and not blocked in any way. Failure to do so will cause variations in pressure. Your unit will not
function as well and it could shorten the life of the product.
ATTENTION: Nettoyer l'extérieur du régulateur au moins une fois par mois. Assurez-vous que
l'orifice de ventilation est ouvert et n’est pas obstrué de quelque façon que ce soit. Le non-respect
de cette précaution causera des variations dans la pression. Votre unité ne fonctionnera pas
comme elle devrait et cela pourrait raccourcir la vie du produit.
(continued on next page)
7
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
MAINTENANCE
OVERNIGHT SHUTDOWN
Turn the temperature control knob to the off position. (The pilot flame alone will keep the frying
compound temperature to 130-145°F(54.5-62.8℃). when not under any load. This will shorten
preheat time when turned back on.)
EXTENDED SHUTDOWN (4 DAYS OR LONGER)
1. Turn the temperature control knob to the off position.
2. Turn the Off/Pilot/On valve control knob to the off position.
3. Turn the manual control valve under the unit to the off position.
4. Turn the supply valve to the off position (not supplied).
5. The entire flue duct opening on the top rear of unit must always be left uncovered.
Filling Fry Tank (CAUTION: NEVER LIGHT PILOT OR TURN BURNERS ON WITH EMPTY TANK)
1. Fill the fry tank approximately 3/4" below the full line. The fry compound will expand as it is
heated. Heat the fry compound to 375° F(190℃) for 20 minutes then check the level. Add or
decrease amount of fry compound so it lines up with the full line.
2. When using solid frying compound, put enough compound in fry tank so at least half or more of
the tank has compound in it. Then set the temperature to 200 ° F(93.3℃) on dial and allow the
compound to liquefy. Add to adjust compound level.
3. Use a quality frying compound.
4. Filter the frying compound frequently, at least once a day.
5. Skim out food particles frequently with a strainer/skimmer.
6. Add at least 15% (of fry tank capacity) of fresh frying compound daily (more if possible) without
overloading tank. If 15% of frying compound is not used daily, remove some of the compound for
other use (gravy, griddle frying, etc.) to permit adding 15% of fresh compound daily.
7. Do not overload the fry baskets. Overloading will result in longer recovery time, longer cook time,
and compound absorption into the product.
8. Prepare the food properly.
9. Keep salt out of the frying compound. Do not salt foods with the basket above the kettle.
10. Ensure a good thermostat operation by checking frying compound temperature with a reliable
frying thermometer. Temperature of compound should be comparable to thermostat setting.
11. Keep the fry tank and thermo-probes clean.
Thermostat Calibration
The fryer control is factory calibrated. If cooking results indicate unit is not maintaining correct
temperatures, consult an authorized service representative.
SERVICE / REPAIR
NOTE: THIS APPLIANCE MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.
NOTE: Parts protected by the manufacturer or his agent are not to be adjusted by the installer,
unless the installer is an authorized service agent.
If you have any questions or problems, contact your nearest Service Representative.
(continued on next page)
8
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
;
;
%
D!
%
%
:
!;
,
! #;
#$&
!0
@ 1:
0
/0
!0
#;
TROUBLESHOOTING
" $' ! &*
! GUIDE
$(
&& '
#
!
;
0
!
,
0
/0
$
D! :
*
!
,
!
!
!
" '
94
?
<
!
94
!;
$
: -
:
!;
: 94
/ !
94
/
!;
.
!;
!
!;
3 D
;
;
*
/
D
* 1
1
!;
(continued on next page)
9
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
EXPLODED VIEW
MODEL: CLGF30-NG
(optional)
(continued on next page)
10
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
Replacement Parts List
MODEL: CLGF30-NG
DESCRIPTION
PART #
qTY
1
Basket
381096
2
2
Regulator
381097
1
3
Gas Safety Control Valve
381099
1
4
Foot
381100
4
5
Burner
381101
4
6
Flame Device System
381103
1
7
Thermopile
381104
1
8
Gas Thermostat
381105
1
9
LC Series Limit Control
381106
1
10
Piezo Igniter
381107
1
11
Cover (optional)
381076
1
NO.
Warranty
Eagle Foodservice Equipment warrants to the original owner that goods supplied hereunder manufactured by Eagle
Foodservice Equipment will be free from defects in materials and workmanship for a period of one year from date of original
installation, not to exceed 18 months from date of shipment from the factory. Eagle Foodservice Equipment will replace, without
charge, any defective parts or component material, upon demonstration to its satisfaction that a breach of warranty did not exist.
For a listing of the authorized parts and service centers near you, contact the factory for assistance.
This warranty does not cover any cost associated with maintenance, misuse, abuse, improper installation, pilot light
adjustments, pilot outage, improper ventilation, adjustments, alteration, calibration, wrong voltage, wrong gas, voltage or gas
conversions, resetting of circuit breakers or safety controls, overtime charges, travel charges on portable equipment, mileage
in excess of 100 miles, operation contrary to the installation and operating instructions, damage caused by flood, fire, or acts
of God. This warranty shall not apply if the nameplate has been removed or altered.
There are no warranties, which extend beyond these warranties. All other expressed or implied warranties, including those
of merchantability or fitness for a particular purpose, which exceed the warranties stated above, are disclaimed by Eagle
Foodservice Equipment and excluded from this agreement. No employee or agent of ours has any authority to make any
representation or warranty, which exceeds the warranties stated above.
NO EAGLE FOODSERVICE EQUIPMENT MAY BE RETURNED EXCEPT UPON WRITTEN AUTHORIZATION
FROM EAGLE FOODSERVICE EQUIPMENT.
(continued on back page)
11
Gas Fryer (NG Unit)
INSTALLATION OPERATING & MAINTENANCE INSTRUCTIONS
Figure 1
(End)
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: 302/653-3000 • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: 302/653-2065
eagle Foodservice equipment, eagle Mhc, specFAB, and retail Display are divisions of eagle Group. ©2016 by the eagle Group
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement