G-SENSUR 2025
INSTRUCTION
G-SENSOR2026
e Accurately records steps and coverts to miles (or km) and
calories
e Built-in clock
e Dual-function LCD read-out
e Lightweight
e Heavy duty clip securely attaches to any waistband or belt
e No sound when counting
e Avoid not valid step counting
MEASURING YOUR STRIDE LENGTH
1. Mark a line in front of your right toe and take ten normal paces.
(walking or running)
2. Mark the point in front of your left toe after the ten paces.
3. Measure the distance between the two marks in inches (or “CM”)
and divide by 10.
4. This is your average stride length - but remember that your running
stride length is much longer than your walking stride length.
MEASURING YOUR WEIGHT
1. Using a bathroom scales or similar, remove excess clothing and
determine your weight Ibs (or “KG").
INPUTTING YOUR STRIDE LENGTH
1. Press the A button so that display changes from “KCAL” to “MILE”
(or “KM”)
2. Press the B button so that display changes from “MILE” to “INCH”
(or “KM” to “CM")
3. Press the C button to advance display by 2 inch (or “5 CM”) until
stride length is correct as measured. (Display range is from 12 to
70 inches or 30 to 180 cm.)
4. Press the A button again to set the input.
INPUTTING Y OUR WEIGHT
1. Press the A button so that display changes from “MILE” to “KCAL”
(or “KM” to “KCAL”)
2. Press the B button so that display changes from “KCAL” to “LBS”
(or from “KCAL” to “KG”)
3. Press the C button to advance display by 2 Ibs (or 1 KG) until weight
is correct as measured.
(Display range is from 40 to 240 Ibs or 20 to 120 KGS)
4. Press the A button again to set the input.
SETTING REAL TIME
1. Press the A button to reach clock mode.
2. Press the B button, display will show “HOUR” 8 “MIN” and the
“HOUR” flashing.
3. Press the C button to advance the digital of “HOUR”, hold on 1
second for rapid advance.
4. Press the B button, display will show “HOUR” 8 “MIN” and the
“MINUTE” flashing.
5. Press the C button to advance the digital of “MINUTE”, hold on 1
second for rapid advance.
6. Press the B button to complete setting - display will show the step/
clock.
WHERE TO POSITION THE PEDOMETER
1. Clip the unit to your belt or the top of your shorts, trousers or slacks
as near as possible to your hip.
2. The unit also is able to count the steps correctly when the front of
the main unit is placed in the angle of less than 60° (show as below
figure 1) or the unit is not parallel to the ground but is placed in the
angle of less than 30° (shown as below figure 2)
TES
Figure 1
Figure 2
AVOID NOT VALID STEP COUNTING
The unit's display will not change or display steps until after you have
walked for more than 6 steps.
TO RESET THE DISPLAYS
1. To reset the Distance and Calories display, press the C button to reset
the data to zero.
2. To reset the Stride and Weight input settings, adjust these as inputting
instructions above.
TO CHANGE THE BATTERY
Please refer to following diagram to replace the battery with proper type
when display dims.
Battery type: CR2032
Step 2 Step 3
Step 1 e x
>
Step 1. Open the battery cover with a coin.
Step 2. Take out the battery with a thin stick that is not easily breakable
and replace the new battery.
Step 3. Press the SYSTEM RESET button with a thin stick that is
not easily breakable and put the battery cover back on the
pedometer.
SYSTEM RESET
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement