Pyle | PLD71MU | Datasheet | Pyle PLD71MU car media receiver

PLD71MU
Motorized Slide Down and Detachable Panel
7-Inch Wide TFT Touch Screen Monitor
Front panel USB port and AUX input
Car DVD/VCD/MP4/CD/MP3 Player
Built in AM/FM Tuner and RDS
SD Card Slot in the panel
Contents
Precautions .....................................2
Selecting Subtitles ..........................27
Safety Information......................... 3
Selecting multi-angle views .............. 27
Disc Notes .................................... 4
Title menu function .......................... 27
Installation .................................... 5
Setup .............................................28
Detaching the control panel .............. 7
General Setup ................................ 28
Changing the control panel ............... 8
Speaker Setup ............................... 30
Electric Connection ...................... 9
Dolby Digital Setup ........................ 30
Remote Control ........................... 10
Preferences Setup ..........................31
Control Panel ................................13
Defaults Table ................................ 32
Touch Panel ....................................13
Other Main Operations ...................33
Unit Keys ...................................... 14
USB Operations .............................. 33
Basic Operations .......................... 16
SD/MMC Card Operations ............... 34
TFT Monitor Adjustment ................ 17
MP3/WMA/JPEG Play ..................... 35
Rear View Camera ........................ 17
MPEG4 Play ................................... 35
Audio Quality Adjustments ...............17
Specifications ............................... 36
Setting Audio Mode .........................18
Trouble Shooting .......................... 37
Reset Factory Settings .................. 18
Alternate Audio/Video Source .......... 18
Radio Operations ..........................19
Listening to the radio ...................... 1 9
Storing stations in memory .............. 1 9
Listening to a preset station ............ 20
RDS Function ................................ 20
DISC Operations ........................... 2 2
Basic Operations ............................22
Select Playback Mode .....................24
AUX Operation ............................... 25
On-Screen Disc Operations .............26
DISC Special Functions ................ 27
Selecting audio languages .............. 27
-1-
Precautions
THANK YOU FOR PURCHASING THIS CAR DVD PLAYER .
Before operating the unit, read this manual thoroughly and keep it handy
for future reference .
To avoid injury or accident , read the following precautions before
installing and operating the unit .
ON INSTALLATION
DO NOT install any receiver in locations where;
- it may obstruct the steering wheel and gearshift lever operations, as this
may result in a traffic accident.
- it may obstruct the operation of safety devices such as air bags, as this
may result in a fatal accident.
- it may obstruct visibility.
DO NOT operate any receiver while manipulating the steering wheel, as
this may result in a traffic accident.
The driver must not watch the monitor while driving.
IF THE DRIVER watches the monitor while driving, it may lead to
carelessness and cause an accident.
IF YOU NEED to operate the receive while driving, be sure to look ahead
carefully or you may be involved in a traffic accident.
IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the
monitor, and no playback picture will be shown.
- This warning appears only when the parking brake wire is connected to
the parking brake system built in the car ( refer to the electric connection)
ABOUT THE LIQUID CRYSTAL DISPLAY (LCD) PANEL
Do not press on the LCD panel on the unit as doing so can distort the
picture or cause a malfunction . The picture may become unclear , or the
LCD panel may be damaged .
NOTES ON CLEANING
-Clean the LCD panel with a slightly damp soft cloth.
-Do not use solvents such as benzine, thinner, commercially available
cleaners or antistatic spray .
-Do not use alcohol to clean the screen .
If your car was parked in a cold or hot place, the picture may not be clear .
The monitor is not damaged . The picture will become clear the temperature in your car becomes normal .
-2-
Safety Information
CAUTION:
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD
PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DVD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
COPYRIGHT PROTECTION
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this
DVD Player, this DVD Player cannot play this disc.
-3-
Disc Notes
Disc formats supported by this
player
DVD
Audio and Video
Disc size 12 cm
VCD
Audio and Video
Disc size 12 cm
CD
Audio
Disc size 12 cm
MP3
Audio
Disc size 12 cm
Discs which cannot be played
with this player
DVD-RAM
CDV
CDG
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Note:
A disc may become somewhat scratched
(although not enough to make it
-4-
unusable) depending on your handle it
and conditions in the usage environment.
Note these scratches are not an
indication of any problem with the player.
Label side
up
Do not touch
the
underside
of the disc
Do not
bend
Wipe the disc from
center
toward the outside
edge
Preparing New Discs with Rough
Spots
A new disc may have rough edges on
its inside and outside edges. If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc. Therefore,
remove the rough edges in advance
by using a ball point pen or pencil as
shown on the right. To remove the
rough edges, press the s i d e o f t h e pen
or pencil against the inside and outside
edges of the disc.
Rough spots
on
outside edge
Ball point pen
or pencil
Rough spots
on inside
edge
Installation
NOTES:
1. Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
2. Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
3. Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
4. Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
5. Install the unit where it does not get in the driver ' s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
6 . Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
7 . If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
Revoving the unit
1. Press the REL button to release the front panel .
2. Remove the control panel .
-5-
Installation
3. Remove the PLASTIC COVER of the both sides away
PLASTIC COVER
4. Insert the two KEY PLAT into the grooves at both sides
of the unit as shown in figure until they click .
KEY PLATE
5. Pulling the levers makes it possible to remove
the unit from the dashboard .
Installation the unit
DASH BOARD
HEX NUT
METAL MOUNTING
STRAP
SPRING WASHER
CONSOLE
PLAIN WASHER
SLIDE BRACKET
HOUSING
TAPPING SCREW
HEX BOLT
-6-
Installation
How To Remove And Install The Front Panel
When detaching or attaching the control panel, be careful not to damage the
connectors on the back of the control panel and on the panel holder.
Detaching The Front Panel
Before detaching the control panel, be sure to turn off the power.
1). Press the “REL” release button and the left hand side of front panel will release.
RELEASE BUTTON
2). Pull-off the front panel and keep the front panel into the case .
PROTECTIVE CASE
Attaching The Front Panel
1). First insert the right hand side of the front panel into the hollow of the unit .
(NOTE : the “bulge” point on the panel must be attached into the hollow of the unit .)
2). Gently push the left hand side of the front panel until you feel a “ Click” .
Hollow
Bulge
PUSH
-7-
Panel Angle Adjustment
CHANGING THE CONTROL PANEL ANGLE
When you want to change the viewing angle of the operating unit to play,
you can touch the
section on touch screen (or press the
button
on the front panel) repeatedly to select the desired angle as follows:
ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGEL 4 - ANGLE 1 .
ANGLE 1
ANGLE 2
ANGLE 4
ANGLE 3
Caution:
Do not insert your finger behind the control panel.
-8-
Electric Connection
WIRING CONNECTION
MAIN UNIT
ISO CONNECTOR
WHITE
BROWN
(B+)12V
REAR CAMERA SWITCH
(B-)PARKING BRAKE
RADIO ANTENNA JACK
YELLOW
REAR CAMERA INPUT
RCA CABLE
FUSE
IGNITION
SWITCH(B+)
REAR RCA OUTPUT
CABLE
RED
BLACK
COAXIAL OUT BROWN
RCH RED
LCH WHITE
MEMORY YELLOW
BACK-UP(B+)
GROUND(B-)
GREY SUBWOOFER
VIDEO OUT 2 YELLOW
FRONT RCA OUTPUT
CABLE
CHOKE
BOX
FRONT RCA RED R
VIDEO OUT 1 YELLOW
FRONT RCA WHITE L
AUTO
ANTENNA
FUSE
BLUE
FRONT
Lch SPK.
REAR
Lch SPK.
WHITE
GREY
WHITE/BLACK
GREY/BLACK
GREEN
VIOLET
GREEN/BLACK
VIOLET/BLACK
FRONT
Rch SPK.
REAR
Rch SPK.
Note:
the earth connection cable (parking brake B-) must be connected in order for DVD
pictures to be played back to the monitor. If the cable has not been correctly
connected, the message “PARKING BRAKE” appears on the monitor.
-9-
Remote Control
DVD/RECEIVER CONTROL
15
MODE
17
7
2
MUTE
PLAY/PAUSE
3
REPEAT
ANGLE
MO/ST
19
13
16
STOP
20
MENU
EQ
MODE
1
CLK
21
LO/DX
6
23
OSD
22
14
BAND
9
ENTER
TITLE/PBC
18
A/PS
VOL
VOL
12
INT
TOP
1
11
5
2
3
RDM
5
4
6
26
AF
10
SEL
8
7
9
25
TA
4
SETUP
GOTO
+10
0
8
Ref # Button
1
CLOCK
2
MODE
3
STOP
4
SETUP
5
24
Function
Press it briefly to view the clock time , Press again to return to
normal display mode . Press longer to set the time .
Press repeatedly to cycle through the various modes:
RADIO > DISC > AUX IN.
Press once to pause playback. Press PLAY/PAUSE to resume
playback. Please note: if you press STOP twice, playback will
start at the beginning of the disc.
Press this button to open the SETUP menu.
In Radio mode, press this button to change between Mono and
MO/ST
Stereo reception modes (when a station is weak, sometimes
(AUDIO) switching to Mono will improve sound quality). In Disc Playback
mode, pressing this button opens the AUDIO setup menu for
making changes to the way the soundtrack is reproduced.
In DVD Disc Playback mode, pressing this button will allow you to
6
SUBTITLE change the subtitle language on discs which have this as an
LOCAL/
option. In Radio mode, press this button to change the radio
DISTANT reception sensitivity in stations are near or far.
7
Pressing this button will open a menu presenting you with the
REPEAT playback repeat options available for that kind of disc.
-10-
Remote Control
Ref # Button
8
GOTO
9
/
10
SEL
11
VOL+/-
12
/ / /
13
14
Function
Press it button to begin playback at a moment in the program you
designate. Use number buttons to enter the data that is needed.
Press these buttons to skip ahead or back one track. (Note: In
DVD mode, press continually the
twice to skip back one)
Press this button repeatedly to cycle through the various audio
and video adjustments you can make: Volume, Bass, Treble,
Balance, Fader, Color, Brightness, Contrast and Tint.
Use these controls to adjust the volume level.
Press to navigate the various menus present in the product.
Menu
Press this button briefly to display the root level directory of a
SubWoofer DVD disc. Press and hold this button to turn on or off the
(
)
SUBWOOFER output.
BAND
(OSD)
15
In Radio mode, press this button repeatedly to switch between
the five radio bands: FM1 > FM2 > FM3 > AM1 > AM2.
In Disc Playback modes, Press this button to see information
about the disc currently in play.
(POWER)
Press this button to turn the unit ON , press and hold to turn the
unit OFF.
16
PLAY/
PAUSE
In Disc Playback mode, press to pause playback. Press again to
start where playback stopped.
17
MUTE
Press this button to turn off the audio. Press again to restore the
sound to its prior volume level.
18
When playing a DVD, pressing this button will open the TITLE
menu which is recorded on the DVD. When playing a VCD disc,
TITLE/
PBC(A/P) press this button to create a PBC (Playback Control) menu for the
disc to assist in making playback selections. In Radio mode,
press and hold this button to start the Auto-Program mode, during
which the tuner will scan for all strong stations and assign them
to the radio preset buttons.
Press this button to adjust the screen viewing angle (see page 8).
19
20
ANGLE
For DVD discs which have alternate viewing angles encoded,
when you see the "angle mark" symbol advising you that these
angles are available, press this button to see them.
21
EQ
Press repeatedly to cycle through the different equalizer curve
presets you may wish to use for enhanced listening.
22
/
In Disc Playback mode, press for fast forward/reverse playback.
23
ENTER
This button is used to confirm selections and settings within
many of the menus in the OSD system.
-11-
Remote Control
Function
Ref # Button
These buttons are used for numeric entry in many different menus.
In addition, in Radio Mode (when RDS is engaged), 0 serves as
the TA button and 9 serves as the AF button.
24
0-9
25
+10
This button is used with the other number buttons for use with
two-digit number entries.
26
1-6
Six numbered preset buttons store and recall stations for each band.
Preparing the Remote Control
Inserting the Battery
1.First push to inside as the direction indicated by the arrow (See 1 )And then
Remove the battery holder as the direction indicated by the arrow (See 2 ).
2.Replace the battery Set a new battery property with (+)side up as illustrated
(See 3 ).
3.Insert the battery holder. Push in the holder to the original position(See 4 ).
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About
30 degree in each the direction of the front of the IR mark.
Note :
The lithium cell in the battery compartment of remote control has been secured for
transport with a foil . Before initial use please remove this foil so that the remote
control is ready for operation .
-12-
Control Panel
Key Functions
Touch Panel
CAR DVD/VCD/CD/MP3 PLAYER WITH MPEG4
SEL
TOUCH SCREEN
CH1-6
REL
MODE
MUTE ON
DSP
MOD
VOL
TA
AF
CLK
VOLUME-
LUD
S-WOOFER
SEL
VOLUME+
RES
IR
AUX IN
Touch Screen Key :
MODE
MUTE ON
DSP
Operating mode selection
CLK
Touch briefly show/hide
clock, touch longer to set
the clock .
To switch of the sound
LUD
Loudness Function
Select EQ function
S-WOOFER
Subwoofer Function
Changing the viewing angle
of the operating unit
Loading and ejecting the
DVD/CD
TA
AF
Turning pre-switching for
traffic announcements ON
and OFF . (Only for RDS)
VOLUME-
Switch ON and OFF and
alternative frequency .
(Only for RDS)
-13-
Decrease the volume level
SEL
Select the menu of the
Picture/Sound
VOLUME+
Increase the volume level
Control Panel
Unit Keys :
11
10
9
8
7
6
5
4
CAR DVD/VCD/CD/MP3 PLAYER WITH MPEG4
SEL
TOUCH SCREEN
CH1-6
REL
MOD
VOL
RES
3
2
12
IR
AUX IN
1
1
AUX Input JACK
For information about connecting a AUX device, please see page 25 .
2
IR SENSOR
3
VOL+/ VOL- KNOB
In normal mode, this knob is used to increase or decrease the volume. It is also
used as an UP/DOWN knob when audio or video settings are being adjusted
when accessed using the SELECT button.
4
(POWER On/Off )/MODE BUTTON
Press this button to switch the device on. WELCOME appears in the display.
Press it again to switch the device off. SEE YOU appears in the display.
In playback mode, you can use the button to select the input mode by pressing
repeatedly until the proper one is found :
DISC > AUX IN > RADIO .
5
ANGLE (Screen position)
Press this button repeatedly to cycle through the different positions.
-14-
Control Panel
6
REL BUTTON
Press this button to release the front panel for removal . Refer to see page 7.
7
8
/CH 1-6 (RADIO PRESET) BUTTON
A) In Disc Playback Mode
Press this button to pause playback, press it again to resume playback.
B) In Radio Mode
you can store 30 stations in memory: 18 FM stations and 12 AM(MW)
stations, each band stores up to six preset stations .
-Store in Memory
> Select the frequency band
> Press repeatedly the button to select the desired memory key .
> Select the station
> Keep the desired memory key pressed in until the station is heard again
after a brief interruption .
-Retrieve a preset station
press the button repeatedly to retrieve a station which had been
stored in the memory in advance the chose number is shown on display .
SELECT BUTTON
To access the available adjustment settings for audio and video, press this
button repeatedly to cycle through and select them:
Buzzer
Volume
Bass
Treble
Balance
Tint
9
Contrast
Bright
Color
Fader
(EJECT) BUTTON
Press it button to eject the DISC or insert the DISC to start play .
10 USB OPERATION
For information about connecting a USB device, please see page 33.
11 SD/MMC CARD SLOT
12 RESET BUTTON
Press this button to return to factory settings .
-15-
Basic Operation
POWER On/Off
Mute Function
Press it to switch the device ON,
press and hold about 2 seconds
to switch the device OFF.
MUTE ON
Ejecting The Disc
Use your finger to touch the
range on touch screen ,
the control panel of the unit
will swing downwards . Then
you can insert the disc or eject the disc .
(You can also press the
button on the
front panel to eject the disc or insert the
disc to start play . )
Touch “MUTE ON” range,
it will mute the sound
but the disc continues
playing . Touch it again
to resume .
Setting The Clock
Touch briefly the “CLK” range
to show/hide the clock .
Touch hold for more than 2’s
the hour will flash , use the
VOL+/- to adjust .Touch it again, the
minute will flash, then use the VOL+/to adjust .
CLK
Select Sources
MODE
DISC
Touch repeatedly the MOD
section on the screen, the
signals will display in the
screen as follow :
AUX IN
Setting The Buzzer ON/OFF
SEL
RADIO
Repeatedly touch “SEL” range
to select the BUZZER item, and
the use the VOL+/- to switch the
BUZZER ON/OFF .
Volume Adjusting
Setting the Background Color
Volume button
In radio mode, repeatedly touch
the “ SEL ” range to select the
“wallpaper” item, and then use
the VOL+/- to select the background color among of the “wallpaper
AUTO, wallpaper: 01 ...... wallpaper: 11” ,
in the “AUTO” mode, the monitor of unit
will change the background color
automatically .
SEL
A
Revolve : clockwise to increase /
Anticlockwise to decrease .
Touch screen
VOLUME-
Touch the screen the
VOLUME+ to increase
the volume level .
VOLUME+
Touch the screen the
VOLUME- to decrease
the volume level .
-16-
Basic Operation
Rear View Camera
TFT Monitor Adjustment
When connecting the rear view camera.
the mirror image of the rear view through
the rear view camera is automatically
displayed on the monitor when you
change the gear to the back position.
(The monitor on the unit only.)
During DISC playback, use your
finger to touch briefly the SEL
section on the screen (or press
SEL button on front panel )
to access the Picture mode
selection menu, by repeatedly touch the
SEL section, and then touch the VOL+/(or rotate the VOL+/-) to adjust the
selected mode .
(The corresponding value will show on
the monitor )
SEL
Volume
Bass
Treble
Buzzer
Audio Quality Adjustment
During DISC playback, use your
finger to touch briefly the SEL
section on the screen (or press
SEL button on the front panel )
to access the Sound mode selection
menu, by repeatedly touch the SEL
section, and then touch the vol+/(or rotate the vol+/-) to adjust the
selected mode . (The corresponding
value will show on the monitor )
SEL
Balance
Fade
Tint
Contrast
Bright
Color
Volume
BRIGHT
Bass
Treble
16
Buzzer
MODE
Fade
MUTE ON
Tint
VOLUME-
SEL
Balance
Contrast
Bright
Color
VOLUME+
FLAT
12: 18
DISC-IN
touch to select
TREBLE
MODE
touch to adjust
ADJUSTABLE ITEMS:
COLOR: 0 to 32
Adjust the color for the picture-lighter or
darker.
BRIGHT: 0 to 32
Adjust if the picture is too bright or
too dark.
CONTRAST: 0 to 32
Adjust the contrast of the bright and dark
portion.
TINT: 0 to 32
Adjust the tint if the human skin color is
unnatural.
-Adjustable when “ NTSC “ is selected for
“ NTSC/PAL “ .
VOLUME-
SEL
+02
MUTE ON
VOLUME+
touch to select
touch to adjust
ADJUSTABLE ITEMS:
Volume: 0 to 32
Adjust volume level by using VOL + / - .
Bass: -14 to +14
Adjust bass level by using VOL + / - .
Treble: -14 to +14
Adjust treble level by using VOL + / - .
-17-
Basic Operation
Balance: R 0-10 to L 0-10 .
Adjust sound balance between left
and right speakers by using VOL + / - .
Fader: F 0 - 10 to R 0 -10 .
Adjust sound balance between front and
rear speakers by using VOL + / VOL - .
The RESET button is to be activated for
the following reasons:
A. Initial installation of the unit when
all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
Setting Audio Modes
ALTERNATE AUDIO/VIDEO SOURCE
Touch the screen the DSP range
DSP
(or press the EQ button on the
remote control ) to select one of
the preset sound modes .
(Rock/Pop/Jazz/Classic/Flat) .
The information will display in the
monitor as follow :
POP
JAZZ
ROCK
CLASSIC
FLAT
FLAT
On the front panel of the unit , there is an
AUX IN jack, to connect analogue replay
devices. Use this jack to replay sound of
other replay equipment such as
DVD players, computers, etc.
Via the loudspeakers.
1). Please f ollowing the diagram below,
connect the external device with stereo
jack plug the AUX IN socket .
2). Press the MOD button to select the
AUX IN connection.
3). Use the buttons on the external
device itself to operate it .
16: 18
DISC-IN
POP
S-WOOFER
OSD
TA
DSP
AF
CLK
LUD
AUX IN
GOTO
AUX IN
touch to select
It`s depend on your habit to select the
Audio mode .
Headphones port
Reset Factory Settings
RESET button is placed on the housing
and must be activated with either a
ballpoint pen or thin metal object.
RESET
RES
-18-
Radio Operation
Listening to the Radio
Start Searching For a Station
Manual Search
Switching To Radio Mode
Touch the screen of “MODE”
range (or press the MOD button
on the front panel ) repeatedly to
select the RADIO mode. the following
information will appears as below:
MODE
FLAT
Automatic Search
12:06
NO-DISC
ST
FM1
1
DX
87.60 MHZ
MODE
MUTE ON
2
VOLUME-
3
4
SEL
FLAT
5
6
VOLUME+
12:06
NO-DISC
ST
FM1
AF
DX
87.60 MHZ
BND
PTY
TA
AF
S-WOOFER
CLK
LUD
STEREO/MONO
APS
LOC/DX
DSP
Touch “
” to next .
Touch “
” to previous .
Selecting The Frequency Band
BND
During Radio mode, briefly touch the
screen of “
” section or press the
“ ” on front panel to increase frequency
by one step of channel spacing .
Briefly touch the “
” section or press
the “ ” button on the front panel to
decrease frequency by one step of
channel spacing .
Touch the screen of “ BND ”
section (or press the BND on
the front panel ) repeatedly to
During Radio mode, touch and hold
(for more than 2’s ) the screen of “ / ”
section or press longer the “
/ ” on
the front panel to start search for a radio
station automatically .
When an FM stereo broadcast is
hard to receive
Touch the “STEREO/MONO” section on
touch screen (or press ST/MO button on
the remote control ) to select the MONO
or STEREO mode .
(When Stereo mode is activated, the ST
symbol will appear . )
To tune in strong-singnal FM
Station only (LO/DX function)
Touch the “ LOC/DX ” range on the touch
screen (or press LO/DX button on the
remote control ) to select the LOCAL
or DX mode .
( You can choose between the LOCAL
and DX(DISTANCE) mode for local or
long-distance traffic news . )
select the band , the message will show
in turn :
FM1
FM2
AM2(MW2)
FM3
AM1(MW1)
-19-
Radio Operation
e.g. FM1, for the stronger signal
level until the search cycle has finished .
The six strongest stations are then
allocated to the corresponding storage
locations . Then the station of the first
storage location is set .
Storing Stations In Memory
With this system, a total of 30 stations
can be stored in the memory of six
buttons. Each band stores up to six
preset stations. The stations might be
FM1, FM2, FM3, AM1(MW1), and
AM2(MW2) band.
The operation is as below :
Scan Function
DX
In Radio mode, briefly touch the
APS section on the touch screen ,
the radio briefly plays all the
preset stations of the frequency band .
6
RDS FUNCTION
APS
Touch the screen of the “ 1-6 ” sections
FLAT
12:06
NO-DISC
ST
FM1
87.60 MHZ
MODE
1
MUTE ON
2
VOLUME-
3
SEL
4
5
In Radio mode, touch it to select
the desired item, it will display the
following as below :
VOLUME+
Touch to preset station
FLAT
-Retrieve a preset station
Touch the 1-6 sections briefly to retrieve
a station which had been stored in the
memory in advance the chose number
is shown on display .
FM1
AF
DX
87.60 MHZ
BND
PTY
TA
AF
S-WOOFER
CLK
LUD
STEREO/MONO
APS
LOC/DX
DSP
In Radio mode, touch briefly the
screen of “TA” range to activate
the TA function.
Touch it again to turn off the TA function .
When the TA function is activated, the
TA symbol appears in the display .
During radio operation in one FM
frequency band the search for a traffic
announcement station is started
automatically (TA SEEK) .
If an FM station is being received which
transmits the latest traffic announcements from time to time, the TP display
lights up.
TA
Automatic Preset Setup
In Radio Mode, Touch and keep the
APS section on the touch screen
for about 2 seconds to active
automatic station storage. The radio
searches within the current frequency
band,
NO-DISC
TA Traffic Announcement
(Priority For Traffic Information)
Automatic Memory Storing &
Program Scanning
APS
12:06
ST
-Store in Memory
> Select the frequency band
> Select the station
> Keep the desired memory key pressed
in until the station is heard again after a
brief interruption .
-20-
Radio Operation
When the TA function is switched on ,
the FM traffic automatically interrupt CD
operation(the word TRAFFIC appears
in the display).
The volume level is increased to the
minimum value for the transmission of
traffic announcements.
Note :
the status of the AF function is shown by
an AF symbol in the display.
If the AF symbol appears in the display,
the AF function is switched on and RDS
transmission date is being received .
If the AF symbol flashes in the display,
the AF function is selected but no RDS
signal can be received at the moment .
After the traffic announcements has
finished, the program that was previously
running is resumed.
PTY FUNCTION
Interruption of the TA Function:
if you would like to interrupt the current
traffic announcement, touch the TA
section on screen briefly . This does
switch off the TA mode .
PTY
AF FUNCTION
(Alternative Frequencies)
In Radio mode, touch briefly the
screen of “AF” range to activate
the AF function. Touch it again
to turn off the AF function .
AF is a function that works with the help
of RDS (Radio Data System) and can
only be used with FM stations . The radio
searches in the background for the best
frequency reception of the station that
has been tuned into .
AF
Touch the AF section on touch screen or
swing and keep the SEL knob in the
TA/AF direction for about 2 seconds ,
the AF function is activated. The AF
symbol appears in the display .
When the AF function has been switched
on, the radio continuously tests the
signal strength of the AF frequency .
The test interval for each AF frequency
depends on the signal strength of the
current station and varies from a few
minutes in the case of weak signals.
Whenever the new AF frequency is
stronger than the station that is currently
tuned in , the radio switched to this
frequency for a short time for a short
time and the message
“NEW FREQUENCY “ is displayed for
one or two seconds.
In Radio mode, touch the screen
of “PTY” range to select the
Program type .
PTY Selection of the program type
besides the stations name, some FM
stations also transmit information on the
type of program. This information can
be displayed by your car radio .
Examples of such types of program
are :
SPORT NEWS POP WEATHER ......
With PTY function you can specifically
select stations transmitting a particular
type of program. Touch the PTY range
on screen repeatedly to call up the PTY
selection menu . The message
“PTY SEEK” then appears briefly in the
display .
When PTY has been selected the radio
starts searching for corresponding PTY
information and stops when the PTY
information has been found, “NO PTY”
appears in the display. If the PTY
information being searched for no longer
exists, the PTY function automatically
switches to normal mode .
-21-
DISC Operation
Basic Operation
Switching the DVD mode
During DISC playback, you can touch
the screen to display the following:
Touch the screen of “MODE” range (or
press MOD button on the front panel ) to
select the DISC mode, it display like
following :
FLAT
12: 16
DISC-IN
DVD
1-0:00:16
MODE
FLAT
12: 16
DISC-IN
MUTE ON
DVD
1-0:00:16
MODE
VOLUME-
VOLUME+
SEL
VOLUME-
FLAT
MUTE ON
SEL
VOLUME+
12: 16
Function setup
(different the source the display is different)
DISC-IN
DVD
1-0:00:16
RANDOM
REPEAT
AUDIO
SUBTITLE
SETUP
INTRO
ZOOM
Stopping Play
TITLE
FLAT
Touch the screen the range (or
press the button on remote
control .) To stop the unit playback.
Touch the
section or press
button on front panel to start play.
12: 16
DISC-IN
DVD
1-0:00:16
S-WOOFER
OSD
TA
AF
DSP
FLAT
CLK
LUD
Pause (still picture)
Touch the “
” section on touch
screen during playback will stop
play temporary, touch it again to
return the normal playback .
GOTO
12: 16
DISC-IN
DVD
1-0:00:16
Rapid Forward/Rapid Reverse
During DISC playback, touch the
screen of “
/
” range or press
longer (more than 2’s) the “ / ”
button on the front panel ,
the speed of rapid forward/reverse
changes according to the disc as
follow:
OK
Touch “
” to next .
Touch “
” to previous .
DVD/VCD/CD/MP3:
Normal Playback 2x
-22-
4x
8x
16x
DISC Operation
Skipping Track
Selecting The Play Modes
During DISC playback, Touch the
/
section on the touch screen
to skip to next/back one track.
(You can also press the
/
on
the front panel to skip to next /back
one track.)
During the Disc playback, touch the
touch screen, it will display the following
as below :
FLAT
DISC-IN
DVD
Note :
1. In DVD mode, touch the
section
continually twice to back one track .
(Press the
button continually twice
to back one track .)
2. For some VCD2.0 disc (PBC-playback
control), above these buttons may be
unavailable .
12: 16
1-0:00:16
RANDOM
REPEAT
AUDIO
SUBTITLE
SETUP
INTRO
ZOOM
TITLE
Touch to select
1). Repeat Function
Zoom Function
ZOOM
Repeatedly touch the section of
the ZOOM, the displaying rate
can be 2x, 3x, 4x, 1/2, 1/3, 1/4 .
Use the direction keys ( / / /
on
remote control or / / / on touch
screen) to move the enlarged picture .
Note: During the JPEG disc playback ,
touch the screen of “ZOOM” range , the
“zoom 100%” word will display, then you
can touch longer (more than 2’s) the
/
section on touch screen (or press the
/
buttons on remote control ) to
zoom in/zoom out the picture. In zoomed
mode, use the direction keys to move
the enlarged picture .
FOR DVD :
Touch the screen the of “REPEAT” range
(or press longer 2/RPT button on the
remote control) to select REPEAT mode
as follow :
CHAPTER REPEAT ON
TITLE REPEAT ON
REPEAT ALL
FOR VCD/CD/MP3 :
Touch the screen the of “REPEAT” range
(or press longer 2/RPT button on the
remote control) to select REPEAT mode
as follow :
REPEAT ONE
REPEAT ALL
REPEAT OFF
Loud Function
LUD
Touch the screen of “ LUD ” range
to switch the Loudness function
ON or OFF.
1. Continuously repeat at the current
chapter/track, when selected REP-ONE
mode .
2. Select REP-ALL mode to continuously
repeat all chapter/track on the current
disc .
Subwoofer Function
S-WOOFER
Use your finger touch the
“ S-WOOFER “ section on the
screen to turn on the Subwoofer
function, touch it again to
cancel function .
2). RDM(RANDOM) Function
During DISC playback, touch screen of
“RANDOM” section ( press the 4/RDM
button longer on the remote control to
play in random.
-23-
DISC Operation
Each playing, the order is different .
(Depend on the disc used for VCD).
Touch it again to cancel this function .
Note : in random mode, the
button is
not available .
DISC Search (GOTO)
FLAT
DISC-IN
DVD
OSD
FOR CD :
Touch the screen of the “INTRO” section
(or longer press the 3/INT button on the
remote control ) to play the previous 6
seconds part of each track/chapter on
disc. (Touch it again to cancel this mode)
TA
AF
DSP
CLK
LUD
GOTO
Touch to select
FLAT
12:16
DISC-IN
DVD
1-0:00:16
GOTO
FOR VCD :
Touch the screen of the “INTRO” section
(or long er press the 3/INT button on the
the remote control ). It display will
following menu as below :
(touch it again to cancel this mode .)
0
ENTER
1
2
3
4
5
6
7
8
9
+10
FOR DVD :
Touch the screen the of “GOTO” range
(or press the GOTO button on the remote
control ) Twice, the screen will display
the following message :
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
TRACK INTERVAL
Use the UP, DOWN, LEFT and RIGHT
arrows on the remote to select the item,
and then press ENTER to confirm .
Title 01/01 Time -:--:-0:10:36
FOR DVD :
Touch the screen of the “INTRO” section
(or long er press the 3/INT button on the
the remote control ). It display will
following menu as below :
(touch it again to cancel this mode .)
You can select the item you want to
watch through TIME setting by using
numberic buttons . (E.x. 0:10:36)
FOR VCD (With PBC OFF):
Touch the screen the of “GOTO” range
(or press the GOTO button on the remote
control )Once, the screen will display the
following message :
Disc Go To --:--
Use the UP, DOWN, LEFT and RIGHT
arrows on the remote to select the item,
and then press ENTER to confirm .
NOTE : For MP3, the 3/INT button is not
available.
1-0:00:16
S-WOOFER
3). INT Function
SELECT DIGEST TYPE:
TITLE DIGEST
CHAPTER DIGEST
TITLE INTERVAL
CHAPTER INTERVAL
12: 16
00:36
Use the numberic buttons to input the
time directly (E.x. : 00:36)
-24-
DISC Operation
3) You now hear the sound from the
external device played back through
the loudspeakers .
Note:
Touch and hold the
/
section on
the touch screen , you can select the
title or chapter of DVD . (Only for the
DVD with title /chapter.)
4) Touch the volume+/- sections on
touch screen or use the VOL+/- on
the remote to adjust the volume level.
AUX Operation
On the front panel of this unit, there is an
AUX IN jack, follow the diagram below t o
connect analogue replay devices.
Use this jack to replay sound of other
replay equipment such as DVD players,
computers, etc. Via the loudspeakers.
AUX IN JACK FRONT PANEL
AUX IN
DOM
VIDEO IN (yellow)
RCH IN (red)
LCH IN (white)
1) Please connect the external device
with stereo jack plug the Aux in socket .
2) Touch the MOD section on screen
or press the MOD button to select the
AUX IN connection. It will display the
following as below :
FLAT
12: 16
DISC-IN
AUX IN
MODE
TA
AF
MUTE ON
CLK
VOLUME-
DSP
LUD
S-WOOFER
SEL
VOLUME+
-25-
DISC Operation
ON-SCREEN DISPLAY FUNCTION
OSD
During playback, touch the screen
the OSD section (or press the OSD
on the remote), it will display the
following as below :
2.Example for VCD/SVCD/CD:
A.Touch or Press OSD for first time:
SINGLE ELAPSED
TRACK 01/16
0:00:56
1. DVD:
A.Touch or Press OSD for first time:
B.Touch or Press OSD for second time:
TITLE ELAPSED
T 01/01 C 01/38
SINGLE REMAIN
0:02:06
TRACK 01/16
Title Number, Total Title Number,
Chapter Number, Total Chapter Number
of this Title of the disc currently being
played will be shown on the screen,
along with the elapsed time.
0:05:10
C.Touch or Press OSD for hird time:
TOTAL ELAPSED
TRACK 01/16
0:31:36
B.Touch or Press OSD for second time:
D.Touch or Press OSD for fourth time:
TITLE REMAIN
T 01/01 C 01/38
3:24:36
TOTAL REMAIN
TRACK 01/16
0:36:26
C.Touch or Press OSD for hird time:
CHAPTER ELAPSED
T 01/01 C 01/38
0:02:56
D.Touch or Press OSD for fourth time:
CHAPTER REMAIN
T 01/01 C 01/38
0:04:32
E.Touch or Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
NOTE:
For CD and MP3,the message will
always display on the screen.
3.Example for MP3:
Each time OSD is pressed or touch , the
message displayed on screen changes
as follows:
SINGLE ELAPSED
E. Touch or Press OSD for fifth time:
The message on the screen will be
cleared.
-26-
SINGLE REMAIN
DISC Special Functions
DVD/VCD Special Function
FLAT
For VCD/CD:
during playback, touch the AUDIO
section of the touch screen or Press
AUDIO on the remote . It is possible to
switch the sound between monaural
and stereo sound.
12: 16
DISC-IN
DVD
1-0:00:16
RANDOM
REPEAT
AUDIO
SUBTITLE
SETUP
INTRO
MONO LEFT
MIX-MONO
TITLE
3. Multi-Angle Function
(for DVD Only)
Touch to select
1. Multi-subtitle Language
Function (for DVD Only)
During DVD playback. Touch
the SUBTITLE section on touch
screen(or press the SUBTITLE
on the remote) .
Each time the button is pressed or touch,
number of the subtitle language changes
in sequential order.
SUBTITLE
Notes:
- The language number is different
according to the disc.
- Some discs only contain one subtitle
language.
- When no different subtitle language
are recorded,
will be displayed
at screen left top corner.
2. Multi-Audio Language Function
For DVD:
During DVD playback , touch
the AUDIO section on touch
screen (or press the AUDIO
on the remote .) Each time the button is
pressed or touch , number of the audio
soundtrack language changes on
sequential order.
Notes:
- The language number is different
according to the disc.
- Some disc only contain one language
soundtrack
- When no different language
soundtrack are recorded
will be
display at screen left top corner.
AUDIO
MONO RIGHT
STEREO
ZOOM
During DVD playback, touch the
section or Press ANGLE button
on the remote . Each time the
button is pressed or touch,number
of the angle changes in sequential
order.
Notes:
- The angle number is different
according to the disc.
- The function only work for disc having
scenes recorded at different angles.
- When no different angle are recorded,
will be displayed at screen left top
corner.
4. Title Menu Function
For DVD:
If the DVD has multiple titles
recorded on the disc. It can
select preferred title from the
title menu to start playback.
- During DVD playback, touch the TITLE
section or press TITLE button on the
remote .The title menu is display.
- Touch the cursor button shown in TV
screen, select preferred title by the
cursor button and confirmed by touch
ENT button .
For VCD:
Press TITLE/PBC button on the remote
control while the disc is playing, you can
switch between "PBC on"and "PBC off"
mode.
TITLE
-27-
Setup
USING THE MENU
GENERAL SETUP
TV Setting
DOLBY
DOLBY
....GENERAL SETUP PAGE....
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
....GENERAL SETUP PAGE....
LB
ON
ENG
SPDIF/RAW
ON
ON
ON
TV Display
Display
TV
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
Nor mal/PS
Nor mal/LB
Wide
Go To General Setup Page
Set TV Display Mode
1. Touch the screen of “ SETUP ” range
or press the SETUP button on remote .
2.The SETUP menu is displayed.
3.Select the preferred item by touch the
/ / / range on the screen
or by using the
/ / /
buttons .
4.Touch screen of the “ OK ” range or
Press ENTER on the remote to confirm .
16:9
4:3 Letter Box
4:3 Pan Scan
The Following Buttons For Entering
The Selection .
Touch to select
OK
Previous Enter
Up Down
Left
1.TV DISPLAY SETUP
This is to select the appropriate TV
aspect (4:3 or 16:9) according to the
connected TV set.
Normal/PS (For 4:3 TV)
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the
left and right edges are cut off.)
Normal/LB (For 4:3 TV)
Played back in LETTER BOX style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
Right
The buttons of the left and right are for
selection of setting type .
The buttons of the up and down are for
selection of the setting program .
Overview Of The Main Menu
DOLBY
( 1)
( 2)
( 3)
(1) General Settings
(2) Speaker Settings
(3) DOLBY Digital Settings
(4) Preference Settings
( 4)
-28-
Setup
GENERAL SETUP
DOLBY
DOLBY
....GENERAL SETUP PAGE....
....GENERAL SETUP PAGE....
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
TV Display
Angle Mark
OSD
OSD Lang
Lang
Spdif Output
Captions
Screen Saver
Last Memor y
ON
OFF
SPDIF/OFF
SPDIF/RAW
SPDIF/PCM
Setup SPDIF
Set Angle Mark
2. ANGLE MARK DISPLAY SETUP
If it is set to ON, when the multi-angle
DVD disc is playing,
(the angle
mark) will appears on the screen; if is
set to OFF, the mark will not appear.
4.SPDIF OUTPUT
This is to activate the audio output
from SPDIF OFF mode to SPDIF/RAW
mode to SPDIF/PCM mode.
LANGUAGE DISPLAYING
DOLBY
DOLBY
....GENERAL SETUP PAGE....
....GENERAL SETUP PAGE....
TV Display
Angle Mark
OSD Lang
Lang
OSD
Spdif Output
Captions
Screen Saver
Last Memor y
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
English
French
Ger man
Spanish
Italian
Por tuguese
Set OSD language
ON
OFF
Closed Caption
3.OSD LANG TYPE SETUP
5.CAPTIONS SETUP
Touch the /
section on the touch
screen or press the
/ button on the
remote to select the preferred OSD
language , then touch the OK section
to confirm .
Activate the CAPTIONS feature by
selecting ON. And release this feature by selecting OFF.
-29-
Setup
GENERAL SETUP
SPEAKER SETUP
.....Speaker Setup Page.....
DOLBY
DOLBY
....GENERAL SETUP PAGE....
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
....Speaker Setup Page....
ON
OFF
Screen Saver
Set Downmix Mode
6.SCREENSAVER SETUP
If the screen displays a static image for
too long, some "burn-in" may occur,
leaving a permanent trace of the image
behind. To avoid this, turn ON the
SCREENSAVER item. After a short
period of inactivity on the monitor, the
unit will substitute a moving image to
avoid burn-in.
DOLBY DOWNMIX
Many DVD discs are recorded using a
surround sound recording technology
called Dolby AC3 5.1. When such a disc
is played in a normal 2- or 4-channel
playback unit like this one, the surround
sound must be "downmixed" to stereo.
In this case, choose "stereo," unless the
output from this unit is connected to a
mobile Dolby surround sound system.
In that case, choose LT/RT.
DOLBY DIGITAL SETUP
DOLBY
....GENERAL SETUP PAGE....
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
Screen Saver
Last Memor y
LT/RT
STEREO
DOWNMIX
DOLBY
....DOLBY Digital Setup....
FULL
DYNAMIC
DOWNMIX
ON
OFF
6/8
4/8
2/8
Set Last Memor y State
OFF
Set DRC OFF
7.LAST MEMORY SETUP
Select the LAST MEMORY output
ON/OFF.
DYNAMIC RANGE CONTROL
Select DRC and adjust the dynamic
range of a Dolby Digital encoded
program. There are 8 steps between
full compression and off compression.
-30-
Setup
--- PREFERENCES PAGE --DOLBY
DOLBY
....Preference Page....
....Preference Page....
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
PAL
AUTO
NTSC
Set TV Standard
English
French
Ger man
Spanish
Italian
Por tuguese
Off
Prefer red Subtitle Language
1. TV TYPE SETUP
This player is capable of playing discs
recorded in either PAL or NTSC formats.
Make the selection based on whether you
are connecting the unit to a PAL TV or an
NTSC TV. You can also set the unit to
AUTO (autoselect). The disadvantage to
autoselect is that each time you turn the
unit on it checks to see what kind of
monitor is connected, which causes a
small delay and some flickering of the
display image which you may find
unpleasant.
3.SUBTITLE LANGUAGE SETUP
Select the preferred SUBTITLE
language by using the cursor buttons.
DOLBY
....Preference Page....
DOLBY
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
....Preference Page....
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
English
French
Ger man
Spanish
Italian
Por tuguese
Prefer red Audio Language
2.AUDIO LANGUAGE SETUP
Select the preferred AUDIO soundtrack
language using the cursor buttons.
English
French
Ger man
Spanish
Italian
Por tuguese
Prefer red Menu Language
4.DISC MENU LANGUAGE SETUP
Select the preferred DISC MENU
language by using the cursor
buttons.
-31-
Setup
--- PREFERENCES PAGE --Age control
DOLBY
DOLBY
....Preference Page....
....Preference Page....
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
TV Type
Audio
OSD
Lang
Subtitle
4PG13
5PGR
6R
7NC 17
8ADULT
OFF
Disc Menu
Parental
Password
Default
Set Parental Control
RESET
Load Factor y Setting
5.PARENTAL
7.DEFAULTS
Selecting the DEFAULT item and
confirming RESET will return ALL
personal settings you have made,
including radio and TV presets, to the
factory default settings.
Select suitable parental guidance with
the cursor buttons and confirm it by
pressing the ENTER button.
DOLBY
DEFAULTS TABLE
....Preference Page....
TV Type
Audio
OSD
Lang
Subtitle
Disc Menu
Parental
Password
Default
GENERAL SETUP
CHANGE
Changed Password
6.PASSWORD SELECTION
The password must be used to make
changes to the Parental Control menu
above. The factory default password is
1379 . To change this password, press
change. You will be asked for the current
password. Once you have entered it,
you have the opportunity to change it.
Then, when you enter the Parental
Control menu, you will be required to
use this new password in order to make
any changes.
-32-
TV DISPLAY
NORMAL/LB
ANGLE MARK
ON
OSD LANGUAGE
ENGLISH
SPDIF OUPUT
SPDIF/RAM
CAPTIONS
ON
SCR SAVER
ON
LAST MEMORY
ON
SPEAKER SETUP DOWNMIX
DOLBY DIGITAL
PREFERENCES
STEREO
DYNAMIC
OFF
TV TYPE
AUTO
AUDIO
ENGLISH
SUBTITLE
OFF
DISC MENU
ENGLISH
PARENTAL
8 ADULT
PASSWORD
1379
Other Main Operation
USB Operation
Changing From DISC to USB Playback
Modes
If the disc present in the player is an
MP3 disc, touch
section on screen
or press the STOP on remote once then
touch or press the GOTO to USB
playback.
If the disc present in the player is an
DVD or VCD or CD disc, touch
on
the screen or press STOP twice on the
remote then touch GOTO section on
the screen or press the GOTO button
on the remote to USB playback.
Following the diagram below, connect
your USB device to the front panel
USB port . If it is properly connected,
the device will be mounted and start
playing automatically.
Important Note:
To prevent damage to the USB device,
do not remove or disconnect it during
playback. it is also a good practice to
remove the USB drive during disc
playback.
In USB Playback mode
Use the UP, DOWN, RIGHT or LEFT
buttons to navigate to and select files
to play, and press ENTER to begin
playback (or viewing, in the case of
JPEG files). To skip to the next or last
track, touch or press the
or
.
Press the
or
buttons for Fast
Forward or Fast Reverse playback.
REPEAT play modes are also available
by repeatedly pushing REPEAT until
the desired mode is found.
Changing From USB to DISC Playback
modes
If you are in USB Playback mode and
wish to begin playback of a disc already
in the player, touch the
range on the
touch screen or press the STOP on the
remote once. Then touch GOTO range
on the screen or press the GOTO on the
remote and the player will switch to
DVD/VCD/CD/MP3 Playback mode.
-33-
Other Main Operation
SD/MMC card OPERATION
The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are
stored into SD and MMC memory card .
Please read below before you start the operation of memory card .
Inserting and removing a SD or MMC card on the front panel of unit .
Inserting the SD or MMC card .
Label side facing
backward
Insert the memory card into slot
with label side facing backward .
Press in till heard a “CLICK” .
Removing the SD or MMC card .
Remove the memory card .
Press in till heard a “CLICK” .
Mode change to SD/MMC card
After a SD or MMC card was inserted into the main unit card slot . The unit will starts
playing the files contained on the memory card . Once the unit read the memory card
successfully, the first file on the memory card will automatically start play back .
Press the mode button repeatedly is allowing changing to other modes .
Change DISC to SD/MMC card
The operations are same as USB mode, refer to see USB operation .
Change SD/MMC card to DISC
The operations are same as USB mode, refer to see USB operation .
File Playback Operation
All the SD or MMC memory car playback operation function is same as the operation
on CD/MP3/WMA .
Please to “ MP3/WMA” operation for more details .
-34-
Other Main Operation
MP3/WMA/JPEG/MPEG4 DISC PLAY
When you insert a disc which contains MP3, WMA or JPEG files, the different file
types are detected, and a list of the files are produced, as shown in the diagram
below.
5
4
3
00:56
2
003/112
1
04:07
Mp3
K
Mp3
woman 1
Mp3
new ton
6
Repeat one
P
....... .......
1 Current track(file)(highlighted bar)
2 Current track (file) number/total
number of tracks(files) in the current
folder.
3 Elapsed playing time of the current
track( not available for JPEG disc)
4 total playing time. ( not available for
JPEG disc)
5 Operation mode icon.
(Play),
(stop), (pause),
(forward)
(reverse).
6 Selected playback mode
Touch the screen, it will display the following as below :
(when the parking brake is applied .)
FLAT
FLAT
08: 16
12: 16
DISC-IN
DISC-IN
MP3
02-0:36:20
MODE
MP3
MUTE ON
Touch repeatedly
VOLUME-
SEL
02-0:36:20
VOLUME+
OK
In stop mode, touch the
/
/
/
sections on touch screen (or Use / /
on the remote control ) to select the item or folder, then touch the “OK” range
(or press ENTER button on the remote control ) to confirm.
/
Touch the screen of “REPEAT ” range or press longer “REPEAT” on the remote control
repeatedly can select two kinds of repeat play mode.
REP-ONE:
Play the same song over and over again.
REP ALL:
Play all songs on the disc, then repeats the entire disc over and over again .
Moving To Another Track :
1. Touch the
or
section to skip a track ahead or back.
2. Press the
or
button to skip a track ahead or back.
Fast Forward/Fast Backward
1. Touch briefly the “
/
” range on touch screen for fast forward / fast backward.
2. Press longer the
or
button for forward or backward .
-35-
Specification
Generall :
Supply Voltage:
Current Consumption:
Signal System:
Discs Played:
12V DC (11V-15V)
Less than10 A
Compositive video 1.0Vp-p 75
(1)DVD-VIDEO Disc
5"(12 cm) single-sided, single-layer
5"(12 cm) single-sided, double-layer
(2)Compact Disc (CD-DA, VIDEO CD)
5"(12cm) disc
Audio Signal Output:
Characteristics:
2ch&4ch line out
(1)Frequency Response
(2)S/N Ratio
(3)Wow and Flutter
20 Hz - 20 KHz
90 dB (JIS)
Below measurable limits
RADIO Section:
Frequency Coverage:
IF:
Sensitivity (S/N = 30 dB):
Frequency Coverage:
IF:
Sensitivity (S/N = 20 dB):
For 3 Bands
(Europe)
FM
87.5 to108 MHz
10.7 MHz
15 dBu
MW
522 to1620 KHz
450 KHz
40 dBu
For 2 Bands
(Europe)
FM
87.5 to108 MHz
10.7 MHz
15 dBu
MW
522 to1620 KHz
450 KHz
40 dBu
For 2 Bands
(U.S.A.)
FM
87.5 to107.9 MHz
10.7 MHz
15dBu
AM
530 to1710 KHz
450 KHz
40 dBu
TFT Monitor:
Monitor Screen Size:
Number of Pixels:
Color System:
7 Inch Wide
480 X RGB X 234 pixels
NTSC/PAL
NOTE:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
-36-
Trouble Shooting
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
SYMPTOM
No power
CAUSE
SOLUTION
The car ignition switch is
not on
The fuse is blown
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
Replace the fuse
Presence of disc inside the Remove the disc in the player,
then put a new one
player.
Disc can not be
loaded or ejected
Inserting the disc in reverse Insert the compact disc with
the label facing upward
direction
The disc is extremely dirty
or defective
Clean the disc or try to play a
new one
Temperature inside the car Cool off or until the ambient
temperature return to normal
is too high
Television/video
imageappears
black-white
The color system is
set incorrectly
The unit is not connected
No television/video to the parking brake
image appears
detection switch
No color in picture
Please switch to correct color
system from menu
Make proper connection
according to “ wire connection ”
The parking brake is not
engaged
For safety reasons no television
/video images are displayed
while the vehicle is moving.
Engaging the parking brake will
cause images to be displayed.
The disc format is not
accordingto the TV-set
used (PAL/NTSC)
Please the television mode of
the choice accommodation
No JPEG files are recorded
Change the disc
on the disc.
JPEG files are not recorded Change the disc Record JPEG
files using a compliant
in a compliant formant
application
The built-in microcomputer Press the RESET button.
The operation keys is not operating properly
Front panel is not properly fixed
do not work
due to noise
into its place
The
antenna
cable
is
not
The radio does not
Insert the antenna cable firmly
connected
work
JPEG disc can
not be played
back
The signals are too weak
Select a station manually
888-J9000-03S
-37-
Download PDF

advertising