Performance Series USB Host - Datamax

Performance Series USB Host - Datamax
1
Safety
Warnings and Cautions
The following Warnings and Cautions are used throughout this manual:
Warning: Warnings alert you to possible safety risks.
Caution: Cautions alert you to the potential for equipment damage.
General Safety Information
Caution: This product is intended for indoor use only.
All service procedures should be done by properly trained and qualified service
personnel.
Any on-site assembly required during the installation process must be performed by
properly trained and qualified service personnel.
When operating, the product must be connected to a properly grounded and
appropriately rated AC receptacle using the supplied cord set.
Caution: This product contains sensitive electronic components that could be damaged
if exposed to excessive force.
Caution: Use only factory-approved consumables and cleaning kits. Use of any nonapproved supplies could damage the product and void the warranty.
Figure: 1 - 1 Caution - Hot
The printhead heats during printing. Do not touch.
1
Media Hub Installation Guide
2
USB Host Installation Instructions
USB Host
Figure: 2 - 1 USB Host
3
USB Host Installation Guide
2 | USB Host Installation Instructions
Tools Needed
•
2.5mm Hex Head Wrench
•
3mm Hex Head Wrench
•
7mm Nut Driver
•
#2 Phillips Screwdriver
•
Long #2 Flat Blade Screwdriver
Safety Overview
Caution: ESD protection is required when performing these steps.
Warning: The cover set may only be removed by a Datamax-O’Neil Authorized Service
Center. Unauthorized service will void the manufacturer’s warranty.
Warning: The printer must be powered off and disconnected from utility power prior to
performing these procedures. Failure to heed this warning may result in personal injury
or damage to internal components.
•
Maintain complete ESD protection in a safe, clean environment at all times while
servicing this equipment.
•
When handling the printhead, grasp it by its edges.
•
Avoid contact between the printhead and clothing.
•
Never pull on any wires to disconnect connectors. This can void the manufacturer’s warranty.
USB Host Installation Guide
4
USB Host Installation Instructions | 2
USB Host Installation Procedure
Note: Retain all hardware for reassembly.
1. Open the media cover assembly.
2. If the present sensor option is installed on the cover, gently pry the sides of the
cable chain outward to disconnect it from the present sensor cable connection
cover.
Note: If there is no present sensor mounted on the media cover, continue to step 5.
Figure: 2 - 2 Cable Chain Disconnect
Note: To clarify the illustration above, the cable chain is shown disconnected from the
printer chassis backbone.
5
USB Host Installation Guide
2 | USB Host Installation Instructions
3. Remove all four 7mm nuts securing the present sensor cable connection cover to
the media cover.
Figure: 2 - 3 PCB Cover
4. Disconnect the present sensor cable connector and route the connector (male) out
of the opening.
5. Loosen all three (3) 2.5mm hex head screws from the upper cover mount.
Note: For an easier re-installation, loosen but do not remove the screws.
Figure: 2 - 4 Upper Screws
USB Host Installation Guide
6
USB Host Installation Instructions | 2
6. Loosen and remove the three (3) 2.5mm hex head screws securing the right side
cover to the printer chassis.
Figure: 2 - 5 Right Side Screws
7. Lift and remove the cover assembly from the printer chassis.
Caution: Exercise caution when removing the cover set assembly and secure it in a safe
position where it will not be damaged.
Figure: 2 - 6 Lift Cover Assembly
7
USB Host Installation Guide
2 | USB Host Installation Instructions
8. If applicable, loosen and remove the power ribbon transport assembly screw and
cover.
Figure: 2 - 7 Power Ribbon Transport Assembly Cover
USB Host Installation Guide
8
USB Host Installation Instructions | 2
9. Gently push the upper panel locking tab upward enough to begin to separate the
top of the panel from the printer frame.
Figure: 2 - 8 Front Panel Removal
Upper Tab
Lower Tab
Caution: Be careful not to damage any surrounding components.
10. While holding the upper part of the panel, gently push the lower panel locking tab
downward enough to separate the panel from the printer frame.
Caution: Be careful not to damage any surrounding components.
9
USB Host Installation Guide
2 | USB Host Installation Instructions
11. Gently separate the panel from the printer frame.
Note: With the display cable still attached, the panel cannot be fully separated.
12. Disconnect the display cable from the front panel connector.
Caution: Do not pull the wires. Pulling the wires could damage both the wires and the
connector.
13. Secure the USB host assembly to the printer chassis using the supplied socket
head screws.
Figure: 2 - 9 USB Host Assembly
Caution: Exercise caution when handling and installing the USB host assembly. The
components are fragile and susceptible to damage.
USB Host Installation Guide
10
USB Host Installation Instructions | 2
14. Connect the small end connector from the supplied cable to the USB host
assembly.
Note: Be sure the connection is secure.
15. Route the cable through the slot opening on the front of the printer chassis, through
the cable clamp to the main PCB assembly area.
Caution: Be sure the cable is routed properly to prevent it from rubbing other
components.
16. Connect the larger connector to junction J3 of the main PCB assembly.
17. Reinstall all other printer components in the reverse order as they were
disassembled.
11
USB Host Installation Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement