Monogram | ZIFS36NDLH | ZIRS36NMRH | ZIFS36NMRH | ZIRS36NMLH | ZIRS36NDRH | ZIFS36NMLH | ZIRS36NDLH | ZIFS36NDRH | Installation Instructions
Add to my manuals20 Pages
advertisement
monogram.com
Installation
Instructions
Stainless Steel 36
″ Built-In Refrigerators and Freezers
ZIRS36N LH – All Refrigerator
ZIRS36N RH – All Refrigerator
ZIFS36N LH – All Freezer
ZIFS36N RH – All Freezer
2
Contents
Before you begin – Read these instructions completely and carefully.
IMPORTANT – Save these instructions for local inspector’s use.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
WARNING
ATTENTION
This appliance must be properly grounded. See “Grounding the Refrigerator,” page 7.
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à terre du réfrigérateur », page 7.
If you received a damaged product, you should immediately contact your dealer or builder. Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the GE Appliance Warranty. See the
Owner’s Manual for warranty information.
For Monogram local service in your area,
1.800.444.1845.
For Monogram Service in Canada,
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
CAUTION
Due to the weight and size of this refrigerator, and to reduce the risk of personal injury or damage to the product – THREE PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
WARNING
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords that have become frayed or damaged.
• Unplug the refrigerator before cleaning or making repairs.
• Repairs should be made by a qualified service technician.
ATTENTION
• Il ne faut utiliser cet appareil que pour l’usage pour lequel il a été construit.
• Il faut réparer ou remplacer immédiatement tout cordon d’alimentation électrique effiloché ou endommagé.
• Débrancher le réfrigérateur avant le nettoyage ou toute intervention.
• Les réparations doivent être faites par un technicien qualifié.
PRUDENCE
À cause du poids et de la taille de ce réfrigérator et pour réduire le risque de blessure et de dommages, IL FAUT TROIS PERSONNES POUR
FAIRE L’INSTALLATION CORRECTEMENT.
Design Information
Flush or Semi-Flush Enclosure Installations .... 3
Product Dimensions ................................................ 3, 4
Accessory Grille Panel Kits ....................................... 4
Installation Examples ............................................. 4, 5
Product Dimensions ..................................................... 5
Installation Preparation
Clearances ....................................................................... 6
Electrical and Water Connection Location ....... 6
Grounding the Refrigerator ...................................... 7
Tools Required ................................................................ 8
Materials Required ........................................................ 8
Hardware Supplied ....................................................... 8
Hardware Recommendations ................................. 8
Flooring .............................................................................. 8
Step 1: Remove Packaging ....................................... 8
Installation Instructions
Step 2: Install Water Line ........................................... 9
Step 3: Install Side Panels ........................................ 10
Step 4: Install Anti-Tip Brackets............................ 10
Step 5: Level Refrigerator ........................................ 11
Step 6: Optional Anti-Tip Precaution .................. 11
Step 7: Connect Water Supply .............................. 12
Step 8: Check Power .................................................. 12
Step 9: Mount Top Grille Panel .............................. 12
Step 10: Adjust Door Alignment ......................... 13
Step 11: Install Toekick ............................................. 13
Step 12: Set Temperature Controls ..................... 13
Step 13: Start Icemaker ............................................ 13
Problem Solving ........................................................... 13
ZUGSS Unified Grille Panel Kit ........................... 14
Design Information
36
″ Stainless Steel Refrigerators, Freezers
Advance Planning
Flush or
Semi-Flush
Enclosure
Installations
Enclosure
Cutout and
Product
Dimensions
0"
3/4"
True Flush Installation
In a flush installation, the refrigerator door
will align evenly with the front face of adjacent cabinet doors. The refrigerator blends into the surrounding cabinetry.
Monogram built-in refrigerators and freezers can be installed flush with typical 24-3/4
″ deep cabinetry.
When installed semi-flush, the case trim will conceal slight gaps around the enclosure. The refrigerator will project forward approximately 3/4
″ beyond the front face of surrounding cabinetry.
Semi-Flush Installation
These refrigerators can also be installed semi-flush into an enclosure using the minimum cutout width. The case trim creates a frame around the opening.
Side Panel Requirements:
• Side panels are not required whenever the refrigerator or freezer is installed into an enclosure or between pantry and oven cabinets.
• Side panels are required whenever the sides of the product are exposed.
• Side panel sizes vary depending on the type of installation being made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer. Be sure to provide the exact dimensions.
• To achieve a flush fit, the finished cutout width must be at least 36
″ wide.
• In a semi-flush installation, the finished cutout must be 35-1/2
″.
• The electrical and water locations must be located as shown for either type of installation.
35"
Case
Width
26-3/4"
Including
Tubular
Handles
24-3/4"
Case
Depth
84-1/2" max
83-1/2" min
Finished
Opening
*Finished Width
2-1/2"
6"
Electrical
Area
5"
24-3/4" Total
Depth
3-1/2"
Water Supply
3-1/2"
5" 5"
Wall View
75" From Floor to Bottom of Electrical
Area
84"*
10"
3-1/2" 10"
36" Frame to Frame
*Shipped at 84
″ installation height.
Can be adjusted to 83-1/2
″ or 84-1/2
″ with grille panel kits.
*36
″ for a flush installation.
35-1/2
″ Min. for a semi-flush installation.
NOTE: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width. See installation examples on the following page.
3
Side By Side
Installation
Of Freezer
And Refrigerator
Accessory
Grille Panel
Kits
Installation
Examples
Design Information
36
″ Stainless Steel Refrigerators, Freezers
*Finished Width
2-1/2"
Electrical
6" 6"
84-1/2" max
83-1/2" min
Finished
Opening
5"
24-3/4" Total
Depth
3-1/2"
Water Supply
3-1/2"
5"
5"
5"
28-1/2"
Wall View
75" From Floor to Bottom of Electrical
Area
For a complete food storage center, install a
Monogram Freezer and Refrigerator side by side.
For even more capacity, install two refrigerators and one or two freezers.
• Order ZUGSS Unified Grille Panel Kit for one continuous stainless steel grille panel.
• Electrical and water locations must be located as shown for either type of installation.
A separate 115V, 60Hz, 20 amp power supply is recommended for each product.
10"
3-1/2"
Freezer
10"
Refrigerator
*72
″ min. for a flush installation
71-1/2
″ min. for a semi-flush installation
NOTE: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width. See installation examples below.
These models are factory set for 84
″ installation height. Adjustments to 83-1/2
″ or 84-1/2″ heights can be made by changing the grille panel.
Order ZGCSS36RH (right hand) or ZGCSS36LH
(left hand) Grille Panel Kit. These kits include 2 grille panels, for 83-1/2
″ and 84-1/2″ installation heights.
ZUGSS Unified Grille Panel Kit
For side by side installation, order ZUGSS grille panel kit. This kit provides one continuous panel to span the width of two products installed together for a unified appearance.
Side panels are required whenever the sides of the product will be exposed.
1/2
″ to 3/4″ side panels are normally set into place and fastened to adjacent cabinetry or to the back wall before rolling the refrigerator or freezer into the opening.
Therefore, the rough-in dimensions must allow for side panel thickness. In both a flush and semi-flush installation, the finished dimension (the width of the opening after side panels are installed) must accommodate the full width of the product.
See page 10 for side panel sizes.
Installation
Between
Base and
Wall Cabinets
Refrigerator or Freezer
1/4" Thick
Side Panels
Finished Dim.
Rough-In Dim.
35-1/2"
36"
NOTE: 1/4
″ thick side panels can be inserted into the case trim, making the rough-in the same as the outside trim width: 36
″.
Cabinet
Refrigerator
Cabinet
Refrigerator door
4
Installation
At End-of-Run
Frameless
Cabinets
Product
Dimensions
Design Information
36
″ Stainless Steel Refrigerators, Freezers
Refrigerator or Freezer
Finished Dim.
Roughed-In Dim.
1/2" Thick
Side Panels
36"
37"
Refrigerator
Cabinet
Refrigerator and Freezer installed side-by-side
Finished Dim.
Rough-In Dim.
1/2" Thick
Side Panels
72"
73"
Side panels, 1/2
″ minimum thickness are required when using frameless cabinets. The side panel acts as a spacer between the cabinet and the case trim and prevents interference with cabinet door swing.
The leading (front) edge must be finished to match surrounding cabinetry.
1/2
″ To 3/4″ Side Panels. Leading
Edge Flush With Cabinet
ZIRS36N RH, Refrigerator
ZIFS36N RH, Freezer
Handle on the left side, the door swings left to right.
ZIRS36N LH, Refrigerator
ZIFS36N LH, Freezer
Handle on the right side, the door swings right to left.
CAUTION
Refrigerators are much heavier at the top than at the bottom – be extra careful when moving.
73-1/2"
10-3/4" Max.
10" Min.
24-3/4"
26-3/4"
PRUDENCE
Les réfrigérateurs sont beaucoup plus lourds en haut qu’en bas. Il faut être prudent lors des déplacements.
4"
Refrigerator door
Cabinet
NOTE: 1/2
″ thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width, (36
″ or 72″ for two models) to calculate the rough-in dimension. The leading
(front) edge must be finished to match surrounding cabinetry.
Refrigerator
Cabinet
Refrigerator door
35" Case
36" Overall
84-1/2" Max.
83-1/2" Min.
5
Clearances
Installation Preparation
36
″ Stainless Steel Refrigerators, Freezers
2"
15"
90
° Door Swing
130
° Door
Swing
25"
Min. to
Wall
36-3/4"
130
°
4" Min.
to Wall
Factory set for a 130
° door swing. Order WX14X99 adjustable door stop to reduce swing to as little as 90
°.
When Installed into a corner:
Allow 25
″ for a full 130° door swing. Allow 15″ for pan removal. Allow 4
″ min. clearance when door swing is adjusted to a 90
° opening for pan access, but pan removal is restricted.
0"
25"
Min. to
Wall
130
° Door
Swing
130
° Door
Swing
25"
Min. to
Wall
Clearances for two products installed side-by-side with the same (left or right) door swing
Allow 2
″ minimum clearance between the products to prevent door swing interference. Order the
WX14X99 adjustable door stop to reduce the factory set 130
° door swing. Allow 15″ minimum to a wall to achieve full drawer extension and pan removal.
NOTE: ZUGSS Grille Panel Kit will not fit this installation.
5"
Electrical and Water
Connection
Locations
Clearances for Multiple Single Door Installations
In a side-by-side installation of a left and right door swing product, no clearance between the units is required. Order ZUGSS Stainless Steel Unified Grille
Panel Kit for one continuous grille panel.
The water line can be routed through the floor or back wall.
• The icemaker water line should be:
– Approximately 3-1/2
″ from the floor on the back wall, or 3-1/2
″ from the back wall on the floor.
– At least 5
″ from either side of the opening.
A 115 volt, 60 Hz 15 or 20 amp power supply is recommended. An individual properly grounded branch circuit or circuit breaker is recommended, as noted on the rating plate.
• Locate the electrical outlet within 5
″ x 6″ shaded area shown.
– 2-1/2
″ from the left side.
Between 75
″ and 81″ from the floor.
IMPORTANT: To insure a flush fit and access to the power cord, locate the electrical outlet as shown.
Clearances for two products installed side-by-side with right and left side hinges together
Allow 5
″ minimum between the two products to prevent one door from striking the other. Use the
WX14X99 adjustable door stop to reduce the factory set 130
° door swing and to allow pan removal.
NOTE: ZUGSS Grille Panel Kit will not fit this installation.
Electrical Outlet
Location 2-1/2"
5"
Water Supply
3-1/2"
5"
10"
6"
3-1/2"
3-1/2"
10"
5"
75"
6
Grounding the
Refrigerator
Installation Preparation
36
″ Stainless Steel Refrigerators, Freezers
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with a
3-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
IMPORTANT:
We recommend two separate 115V, 60Hz, 20 amp properly grounded electrical outlets for a side-by-side installation of two products. Each electrical outlet should have a voltage rating that matches the rating plate.
Use of Adapter plug
Because of potential hazards under certain conditions, we strongly recommend against use of an adapter plug. However, if you still elect to use an adapter, where local codes permit, a TEMPORARY
CONNECTION may be made to a properly grounded
2-prong wall outlet by use of a UL listed adapter available at most hardware stores.
The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM THE
POWER CORD.
When disconnecting the power cord from the adapter, always hold the adapter in place with one hand and pull the power cord with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT
USE the appliance until a proper ground has again been established.
Use of Extension Cords
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet, and that the electrical rating of the cord be
15 amperes (minimum) and 120 volts.
PRUDENCE
FICHE D’ADAPTATION
(Fiches d’adaptation non permises au Canada)
CAUTION
Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
7
Tools
Required
Step 1
Remove
Packaging
8
Materials
Required
Hardware
Supplied
Hardware
Recommendations
Flooring
Installation Preparation
36
″ Stainless Steel Refrigerators, Freezers
• Tinsnips to cut banding
• Stepladder
• Bucket
• Level
• 1-1/4
″ open-end wrench
• Appliance hand truck
• Tubing cutter
• 7/16
″ open-end wrench
• #2 Phillips screwdriver
• Stubby Phillips screwdriver
• Drill and appropriate bits
• 7/16
″ socket with 3″ extension for ratchet
• Safety glasses
• 2x4, 35
″ long, for Anti-Tip support, see page 10
• Stick-on hook and loop fastener strips for 1/4
″ side panels
• 1/4
″ copper water line tubing or GE SmartConnect
™
Tubing Kit
• Water shut-off valve
• Screws to secure refrigerator to cabinetry
• 1/4-1/4 union with nuts
• Anti-tip mounting brackets
• Water shut-off valve
• Water filter WR97X0214
For proper installation, the refrigerator and freezer must be placed on a level surface of hard material that is at the same height as the rest of the flooring.
The floor must be strong enough to support a fully loaded product, or approximately 1,200 lbs.
NOTE: Protect the finish of the flooring. Cut a large section of the cardboard carton and place under the product where you are working.
CAUTION
Refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck, handle from side only.
PRUDENCE
Le réfrigérateur est beaucoup plus lourd en haut qu’en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.
• Remove outer carton.
– Carefully cut banding at the top and bottom.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
• Remove styrofoam pads taped to base cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN
IN ORDER TO REMOVE SKID!
• The unit is secured to the skid with 3 slotted tie-down straps. First remove the 5/16
″ bolts from the base channels in the tie-downs, then remove the 7/16
″ bolts securing the straps to the skid.
• Protect the flooring. Cut a large piece of the cardboard carton and place under the product where you are working.
• Support blocks on the bottom must be removed before the refrigerator is taken off the skid or damage will occur. Remove support blocks by carefully tilting cabinet to side and sliding out.
• Lift the refrigerator off the skid with an appliance dolly. Handle from the sides.
CAUTION
7/16" Bolt
DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
PRUDENCE
IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE
RÉFRIGÉRATEUR POUR L’ENLEVER DE LAY PALETTE.
Step 2
Install
Freezer
Water Line
Installation
36
″ Stainless Steel Refrigerators, Freezers
• A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 p.s.i.
• Route 1/4
″ OD copper or GE SmartConnect
™ between house cold water line and the water
tubing connection location.
• Tubing should be long enough to extend to the front of the freezer. Allow enough to accommodate bend leading into the water valve.
Floor
Waterline Tubing
• Install optional water filter in the water line near the freezer. A water filter is recommended in areas where water supply contains sand or particles.
Installation instructions are packed with the filter.
NOTE: The only GE approved plastic tubing is supplied in the GE SmartConnect
™
Refrigerator
Tubing Kits. Do not use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home.
GE SmartConnect
™
Refrigerator Tubing Kits are available in the following lengths:
2
′ (0.6 m) WX08X10002
6
′ (1.8 m) WX08X10006
15
′ (4.6 m) WX08X10015
25
′ (7.6 m) WX08X10025
Shut off the main water supply
Turn on the nearest faucet long enough to clear the line of water.
NOTE: Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered to.
Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
Install a shut-off valve between the icemaker water valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be easily accessible.
NOTE: Saddle type shut-off valves are included in many water supply kits, but are not recommended for this application.
9
Step 3
Install
Side Panels
Step 4
Install
Anti-Tip
Brackets
10
Installation
36
″ Stainless Steel Refrigerators, Freezers
• Side panels are required whenever the sides of the product will be exposed and when installed between frameless cabinets. See pages 3 and 4.
• Side panels are not required when installed into an enclosure.
• Side panel installation will be determined by the design of the side panel you have previously chosen.
• Side panels must be installed plumb.
Illustration A
1/4
″
Side Panels –
Insert end of side panel into case trim.
84"
23-9/16"
• If you choose to use 1/4
″ side panels, they should be inserted into the case trim as illustrated. Fasten the panels to the product with stick-on hook and loop fastener strips before setting in place. See illustration A.
• 1/2
″ to 3/4″ side panels are normally set into
place and fastened to adjacent cabinetry or
the back wall before rolling the product into
the opening. See illustration B.
Illustration B
1/2
″
to 3/4
″
Side
Panels – Leading edge of side panel is flush with cabinet front. Fasten to the back wall using a cleat.
84"
24-3/4"
Trim
2-9/16"
Top View
Standard 4
″ high toekick or trim to fit. Height may vary depending on application.
3-3/4"
Top View
Standard 4
″ high toekick or trim to fit.
Height may vary depending on application.
WARNING
ANTI-TIP PRECAUTIONS
The refrigerator is top-heavy and must be secured to prevent the possibility of tipping forward.
ATTENTION
PRECAUTIONS CONTRE LES BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement vers l’avant.
• Cut a 2
″ x 4″ x 35″ block and secure the block to the mounting brackets provided using #12 or #14 wood screws.
• Secure the bracket with wood block to the back wall so that it is 84
″ (or your installation height) from the finished floor. Use #12 or #14 wood screws. See illustration.
• Screws must penetrate at least one inch into vertical wall studs.
• Before pushing the refrigerator into the opening, plug the power cord into the receptacle. Open the grille panel and reach into the opening at the back to grasp the power cord. Pull the power cord into the opening as you push the refrigerator back.
• Gently push refrigerator into the opening with hands against front corners.
Brackets
Required
Block
2 x 4 Cut
35" Length
Height
From
Floor to
Bottom of Wood
Block
Soffit
Brackets
Not Required
Beneath a
Soffit
Side View
Installation
Height
From Floor
Mounting
Bracket
Screws Mounted into
Vertical Wall Studs
IMPORTANT NOTE: When the refrigerator is installed under a soffit or if there is not enough height for this method of security, brackets cannot be used. Proceed to step 5 to level the refrigerator and then to step 6 to secure refrigerator to cabinets. The refrigerator must be secured to prevent tipping.
Step 5
Level
Refrigerator
Step 6
Secure
Product to Sides
Installation
36
″ Stainless Steel Refrigerators, Freezers
These products have a 4-point leveling system.
The front is supported by leveling legs, the rear is supported by wheels.
• Adjust rear wheels beneath the product to just barely touch the 2x4 block.
• Turn the 7/16
″ hex nut located above the front wheels. Turn to raise or lower.
• For front leveling legs, use a 1-1/4
″ open-end wrench.
• Adjust carefully; the product should be level and plumb with cabinetry, and should align with toekick height.
Hex Nut Adjusts
Rear Wheels
Leveling Leg
CAUTION
The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1
″. If the installation requires more than 84-1/2
″ height, the installer should elevate the refrigerator on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening. If you attempt to raise the
refrigerator more than 1
″, you will damage the
front leveling legs and rear leveling wheels.
PRUDENCE
Les roues de nivellement arrière et les pattes de nivellement avant permettent un réglage maximal de 25 mm (1 po). Si l’ouverture pour le réfrigérateur a une hauteur supérieure à 2,15 m (84-1/2 po), l’installateur doit élever le réfrigérateur sur une feuille de contre-plaqué ou des glissières. Il est
également possible d’ajouter des baguettes de finition des placards sur le haut de l’ouverture afin de la réduire. Lever le réfrigérateur de plus de 25
mm (1 po) endommage les pattes de nivellement avant et les roues de nivellement arrière.
NOTE: Whenever possible, perform this step for additional anti-tip security. This step can be used as an alternate to Step 4, Anti-Tip bracket installation, whenever brackets cannot be used.
Stud
Refrigerator
Cabinet
Door
Spacer
Block
OR
When using 1/2
″ to 3/4″ side panels, the front flange of the case trim is attached to the side panel.
• Open door to access case trim.
• Drill hole in trim below interior opening. Drive screw through trim and side panel.
• Follow the same procedure on opposite side.
If installed between cabinets with no side panels or in a custom enclosure, install a spacer block as shown.
• Open door to access case trim.
• Drill hole in trim below opening. Drive screw through trim and into block.
• Follow the same procedure on opposite side.
11
Step 7
Connect
Freezer
Water Supply
Step 8
Check Power
Step 9
Mount Top
Grille Panel
Installation
36
″ Stainless Steel Refrigerators, Freezers
• Locate and bring tubing to the front of the cabinet.
• Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off water.
Copper Tubing:
• Slip a 1/4
″ nut and ferrule (provided) over both ends of the copper tubing. Insert tube into the union fitting on the unit and tighten nut to union.
• Turn on the water to check for leaks.
GE SmartConnect
™
Tubing:
• Insert the molded end of the tubing into the refrigerator connection. Tighten the compression nut until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
NOTE: Make sure excess tubing length does not interfere with toekick installation.
• Check to make sure power is on by opening the door to see if interior lights are on.
For shipping purposes, the top case trim is secured at 84
″ installation height.
To raise case trim to 84-1/2
″ installation height or
to lower case trim to 83-1/2
″:
• Loosen 2 screws on both sides and raise or lower the top case trim to meet soffit height or to the top of adjacent cabinets.
• Tighten all 4 screws.
• Mount the grille panel by dropping into slots on the case trim.
The grille panel assembly is factory set for an 84
″ installation height. If installation height is 83-1/2
″ or 84-1/2
″, order ZGCSS36RH (right hand) or
ZGCSS36LH (left hand) grille panel kit.
Raise To
Installation
Height
Top Case Trim
Screws
1-1/2" min. gap
IMPORTANT: Maintain 1-1/2
″ min. gap between top of doors and bottom of grille panel.
12
Step 10
Adjust Door
Alignment
Step 11
Install
Toekick
Step 12
Temperature
Controls
Step 13
Start
Icemaker
Problem
Solving
Installation
36
″ Stainless Steel Refrigerators, Freezers
Check door alignment. The top of the door should be parallel with the grille panel. If the door appears to be too high or too low on the handle side, adjustments can be made by turning the hinge.
• To raise the door, turn adjustable hinge pin toward the right.
• To lower the door, turn hinge pin toward the left.
Turn the hinge pin with a 5/16
″ wrench or, on some models, use the 3/16
″ Allen wrench taped to the hinge.
Door Should be Parallel
With Grille Panel
Bushing
Door Hinge
Case Hinge
Pin Shoulder
Raise
5/16" Wrench
• A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws.
IMPORTANT: The vented toekick must remain unobstructed for proper air circulation and operation.
• Set temperature control at “5”.
IMPORTANT: Allow 24 hours for temperatures to stabilize before making adjustments.
• Set the switch to I (on). The green light will come on and the icemaker will begin operation automatically.
• Be sure nothing interferes with the sweep of the feeler arm.
• Discard the first few batches of ice cubes.
• To turn the icemaker off, set the switch to O (off).
Allow 45 minutes for the icemaker to resume operation.
Power Switch
Feeler Arm
Green Power Light
Operation of Refrigerator and Freezer
If the product does not operate after checking the installation instructions:
• Check to be sure power cord is plugged in the wall outlet.
• Check to be sure that fuse or circuit breaker is turned on.
If any of these problems persist:
Call for Monogram local service in your area,
1.800.444.1845.
Cleaning the Stainless Steel Exterior
Stainless Steel has some unique cleaning characteristics. In order to keep your refrigerator or freezer looking like new, we suggest cleaning it with
Stainless Steel Magic or a similar product.
Stainless Steel Magic is available at Ace, True Value,
Home Depot, Servistar, HWI and other leading stores.
It is also available through GE Parts by calling
1.800.626.2002. Order part number WX10X15.
13
ZUGSS Trim Kit
Unified Stainless Steel Custom Grille Panel
Tools and Materials Required:
• #1 and #2 Phillips screwdrivers or sockets
• 1/4
″ angled wrench and 1-1/2″ open ended wrench
• Drill and appropriate bits
• Custom grille panel
• Safety glasses
• Gloves to protect against sharp edges
C
D
E
Parts List:
A. Soffit Vent Top
B. Left Side Case Trim
C. Right Side Case Trim
D. Center U-Shape Trim
E. Grille Base Wrap
F
G
F. Stainless Steel Unified Panel
G. Foam Spacer Pads
B
A
Completion Time: Allow approximately 3 hours to install this kit.
IMPORTANT: 2 People are required to install this kit.
CAUTION: Disconnect power before you begin.
Step 1
Install
Spacer Pads, Replace
Side Case Trims
CAUTION:
Handle parts with care to avoid scratching.
In a side by side installation, the inside case trim of both products will be removed and replaced with a shorter trim.
• Lift up to remove the supplied grille panel assembly on both products. Discard both assemblies.
Foam
Spacer
Pads
• Remove the Phillips head screws from the inside case trim of each product as shown. Remove and discard side trim. Retain screws.
• Apply the supplied foam spacer pads to the mating side of one product as shown.
• Install new side case trim with notches toward the bottom. Install with original screws.
14
Step 2
Install
Anti-Tip
Brackets
Step 3
Level Both
Products
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
WARNING
ANTI-TIP PRECAUTIONS
These products are heavy at the top and must be secured to prevent the possibility of tipping over.
Brackets
Required
Block
Soffit
Brackets
Not Required
Beneath a
Soffit
Height
From
Floor to
Bottom of Wood
Block
ATTENTION
PRECAUTIONS CONTRE LES BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement vers l’avant.
• Cut a 2
″x4″ block, 71″ long. Secure the 2″x4″ to the
4 mounting brackets provided using #12 or #14 wood screws.
• Secure the brackets with wood block to the back wall so that it is 84
″ (or your installation height) from the finished floor. Use #12 or #14 wood screws. See illustration.
• Screws must penetrate at least one inch into vertical wall studs.
Roll Both Products into Opening
• Gently push each product into opening with hands against front corners. Push back into the opening until it is flush or semi-flush with adjacent cabinets.
2 x 4 Cut
71" Length
Side View
Installation
Height
From Floor
Mounting
Bracket
Screws Mounted into
Vertical Wall Studs
IMPORTANT NOTE: When the products are installed under a soffit or if there is not enough height for this method of security, use Step 4 as an alternative. The refrigerator and
freezer must be secured to prevent tipping.
Both products MUST BE LEVEL AND PLUMB with each
other and adjacent cabinetry on each side. Toekick heights should align with cabinetry.
• Adjust carefully. Both models have 4-point leveling.
The front is supported by leveling legs, the rear is supported by wheels.
• Raise units to the same level, aligning with adjacent toekick heights.
• Adjust rear wheels beneath the product to just barely touch the 2x4 block.
• Turn the 7/16
″ hex nut located above the front wheels to raise or lower the back of the refrigerator.
• To adjust the front leveling legs: Use a 1/4
″ angled wrench to turn the top of the leveling leg, or turn the bottom of the legs with a 1-1/4
″ wrench.
Hex Nut Adjusts
Rear Wheels
Leveling Leg
Units must be 1
″ apart and evenly aligned at top
and bottom. The inside case trims must align, top and bottom.
CAUTION
The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of
1
″. If the installation requires more than 84-1/2″ height, the installer should elevate the refrigerator on a sheet of plywood or runners.
Cabinetry trim could also be added across the top of the opening to shorten the opening. If you
attempt to raise the refrigerator more than 1
″,
you will damage the front leveling legs and rear leveling wheels.
PRUDENCE
Les roues de nivellement arrière et les pattes de nivellement avant permettent un réglage maximal de 25 mm (1 po). Si l’ouverture pour le réfrigérateur a une hauteur supérieure à 2,15 m (84-1/2 po), l’installateur doit élever le réfrigérateur sur une feuille de contre-plaqué ou des glissières. Il est
également possible d’ajouter des baguettes de finition des placards sur le haut de l’ouverture afin de la réduire. Lever le réfrigérateur de plus de 25
mm (1 po) endommage les pattes de nivellement avant et les roues de nivellement arrière.
15
Step 4
Secure
Products
To Sides
Step 5
Install Center
Trim Strip
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
NOTE: This step can be used as an alternative to Step 2,
Anti-Tip bracket installation, whenever brackets cannot be used. Whenever possible, perform this step for additional anti-tip security.
Stud
Refrigerator
Cabinet
Door
Spacer
Block
When using 1/2
″ to 3/4″ thick side panels, the front flange of the case trim is attached to the side panel.
• Open door to access case trim.
• Drill hole in trim slightly below the interior opening.
• Drive screw through the trim and into the side panel.
• Follow the same procedure on the opposite outside product trim.
OR
If the product is installed between cabinets with no side panels or into a custom enclosure, install a spacer block as shown.
• Open doors fully.
• Starting at the top, press trim strip over inside case trims of both products.
• Continue pressing trim until you reach the bottom of the case trims. The trim will align with the top and bottom of the case trim.
Case Trim
U-Shape
Trim
Step 6
Remove
Wire Fence and
Switch Cover
Remove
3 Screws
• Remove 3 screws holding the wire fence on both products. Retain fences and all screws.
Grille Base Cover
• Lift off grille base covers. Discard covers.
16
Step 7
Install
Grille Base
Cover
Unified Base Cover
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Place
Trim Over
Hinges
• Open doors fully.
• Install the double width grille base cover by slipping the notched ends over the hinges.
Step 8
Remove
Grille Frame
Install
3 Screws
• Place wire fence over the grille base cover (textured side out). Drive original wire fence screws through the fence, the grille base cover and into the frame.
Remove
Screws
Install
3 Screws
Remove
Screws
• Back out 2 screws on each side of the top case trim.
• The top piece is secured to the unit with a rubber dust gasket. Roll the trim upward to access and remove end screws as shown. Remove and discard inside pieces.
• Slide assembly out of the rubber gasket.
Dust
Gasket
Remove
Screws
17
Slip Dust Gasket
Into Trim On One End
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Slip Second Dust
Gasket Into Trim
Step 9
Install
Soffit
Vent Top
Step 10
Mount
Unified
Grille Panel
• Separate the top and hinge side trim pieces by removing side screws. Discard top piece; retain screws.
• Install one end piece to unified top piece with
2 original screws.
• Slip end of rubber dust gasket into end of top unified piece and slide trim towards the center.
Engage the second piece of gasket and continue sliding trim until even with opposite ends.
• Reinstall end pieces to case trims. Push top piece up against soffit or to installation height. Tighten screws on both sides.
• Whenever possible, place a level on the top trim.
Adjust side trims until entire grille frame is level.
• Mount the unified grille panel by dropping into slots on the outside case trim.
Reinstall
Screws
18
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Step 11
Adjust
Door
Alignment
Bushing
Door Hinge
Case Hinge
Pin Shoulder
Raise
5/16" Wrench
Check door alignment. The top of the door should be parallel with the grille panel. If the door appears to be too high or too low on the handle side, adjustments can be made.
• Use a 5/16
″ wrench to turn the hinge.
• To raise the door, turn adjustable hinge pin toward the right.
• To lower the door, turn hinge pin toward the left.
19
Pub. No. 49-60073-4
Part No. 197D3003P001
08-07 JR
Note: While performing installations described in this book, safety glasses or goggles should be worn.
For Monogram ® local service in your area, call
1.800.444.1845.
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225 ge.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Design Information
- 3 Flush or Semi-Flush Enclosure Installations
- 3 Enclosure Cutout and Product Dimensions
- 4 Accessory Grille Panel Kits
- 4 Installation Examples
- 5 Product Dimensions
- 2 Installation Preparation
- 6 Clearances
- 6 Electrical and Water Connection Location
- 7 Grounding the Refrigerator
- 8 Tools Required
- 8 Materials Required
- 8 Hardware Supplied
- 8 Hardware Recommendations
- 8 Flooring
- 8 Step 1: Remove Packaging
- 2 Installation Instructions
- 9 Step 2: Install Water Line
- 10 Step 3: Install Side Panels
- 10 Step 4: Install Anti-Tip Brackets
- 11 Step 5: Level Refrigerator
- 11 Step 6: Optional Anti-Tip Precaution
- 12 Step 7: Connect Water Supply
- 12 Step 8: Check Power
- 12 Step 9: Mount Top Grille Panel
- 13 Step 10: Adjust Door Alignment
- 13 Step 11: Install Toekick
- 13 Step 12: Set Temperature Controls
- 13 Step 13: Start Icemaker
- 13 Problem Solving
- 14 ZUGSS Unified Grille Panel Kit