users manual - Allesvast.nl

users manual - Allesvast.nl
USERS MANUAL
16 GA. MEDIUM CROWN AIR STAPLER
MODEL: XJKC851
WARNING
Failure to follow warning could result in DEATH OR SERIOUS INJURY.
M0731
01/12 V1
CONTENTS:
IMPORTANT INFORMATION
EXPLANATION OF THE NAILING ACTION
GENERAL SAFETY RULES
WORK AREA
PERSONAL SAFETY
TOOL USE AND CARE
SERVICE
AIR SOURCE
DESCRIPTION AND SPECIFICATION
SPECIFICATION
FEATURES
ASSEMBLY/INSTALLATION
OPERATION
LUBRICATION
ADJUSTING AIR PRESSURE
CONNECTING AIR SUPPLY
TOOL TESTING
NAIL LOADING
METHODS OF OPERATION
COLD WEATHER OPERATION
ADJUSTING THE NAILING DEPTH
ADJUSTABLE THE EXHAUST
MAINTENANCE
JAM CLEARING
CLEANING
STORAGE
HOOKUP INSTRUCTIONS FOR TOOL TO AIR SUPPLY
RECOMMENDED HOOKUP
TROUBLE SOLVING
P1
P1
P1
P1
P1
P1
P2
P2
P3
P3
P4
P4
P4
P4
P4
P4
P5
P5
P6
P6
P6
P7
P7
P7
P7
P7
P7
P7
P8
IMPORTANT INFORMATION
The employer must enforce the use of safety glasses by
the tool operator and others in work area.
ALWAYS WEAR EAR AND HEAD PROTECTION. Always
wear ear protection to protect your ears from loud noise,
Always wear head protection to protect your head from
flying objects.
USE SAFETY EQUIPMENT. A dust mask, non-skid safety
shoes and a hard hat must be used for the applicable
conditions. Wear a full face shield if you are producing
metal filings or wood chips.
DRESS PROPERLY. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts and increases
the risk of injury.
STAY ALERT, WATCH WHAT YOU ARE DOING AND USE
COMMON SENSE WHEN OPERATING A POWER TOOL.
Do not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating the tool may cause serious injury.
AVOID UNINTENTIONAL FIRING. Keep fingers away from
trigger when not driving fasteners, especially when
connecting the tool to the air supply.
DO NOT OVERREACH. keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
MAKE SURE AIR HOSE IS FREE OF SNAGS AND
OBSTRUCTIONS. DO NOT ATTACH AN AIR HOSE OR
TOOL TO YOUR BODY. Entangled or snarled hoses can
cause a loss of balance or footing in addition to
unintentional tool operation. Attach the hose to the
structure to reduce the risk of loss of balance of the hose
shifts.
WARNING
TO AVOID SERIOUS PERSONAL INJURY, ALL USERS AND
EMPLOYERS/OWNERS MUST READ AND UNDERSTAND
ALL INSTRUCTIONS IN THIS MANUAL BEFORE OPERATING
OR MAINTAINING THIS TOOL.
Keep this manual for the safety warnings and precautions,
operating, inspection, maintenance. Keep this manual and
the receipt in a safe and dry place for future reference.
EXPLANATION OF
THE NAILING ACTION
SINGLE ACTUATION MECHANISM:
First, press the safety against the wood; next, pull the
trigger to drive the fastener. After fastening once,
fastening will not be possible again until the trigger is
released and pressed again.
CONTACT ACTUATION MECHANISM:
First, press the safety against the wood; next, pull the
trigger to drive the fastener. First. Pull the trigger; next,
press the safety against the wood to drive the fastener. If
the trigger is held back, a fastener will be driven each
time when the safety is pressed against the wood.
FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the safety against the wood; next, pull the
trigger to drive the fastener. Follow the same sequence
to continue driving fasteners.
GENERAL SAFETY RULES
TOOL USE AND CARE
WORK AREA
NEVER POINT TOOL AT YOURSELF OR OTHERS IN
WORK AREA. Always assume the tool contains
fasteners. Never point the tool at yourself or others,
whether it contains fasteners or not. If fasteners are
mistakenly driven, it can lead to severe injuries. Never
engage in horseplay with the tool. Respect the tool as a
working implement.
KEEP FINGERS AWAY FROM TRIGGER WHEN NOT
DRIVING FASTENERS TO AVOID ACCIDENTAL FIRING.
Never carry the tool with finger on trigger since you
could drive a fastener unintentionally and injure yourself
or someone else. Always carry the tool by the handle
only.
NEVER MODIFY OR ALTER A TOOL. Doing so may cause
malfunction and personal injuries.
KNOW THIS TOOL. Read manual carefully, learn its
applications and limitations, as well as the specific
potential hazards related to this tool.
USE ONLY FASTENERS THAT ARE RECOMMENDED FOR
YOUR MODELS. Do not use the wrong fasteners or load
the fasteners incorrectly.
CHECK FOR MISALIGNMENT OR BINDING OF MOVING
PARTS, BREAKAGE OF PARTS, AND ANY OTHER
KEEP THE WORK AREA CLEAN AND WELL LIGHTED.
Cluttered benches and dark areas increase the risks of
accidents.
DO NOT OPERATE THE TOOL IN EXPLOSIVE
ATMOSPHERES, such as in the presence of flammable
liquids, gases, or dust. The tool creates a spark which
may ignite flammable liquids, gases or dust.
KEEP VISITORS AWAY. Do not let visitors handle the
tool. All visitors should be kept safety away from work
area.
NEVER ENGAGE IN HORSEPLAY WITH THE TOOL.
Respect the tool as a working implement.
PERSONAL SAFETY
OPERATORS AND OTHERS IN WORK AREA MUST WEAR
SAFETY GLASSES WITH SIDE SHIELDS. When operating
the tool, always wear safety glasses with side shields,
and make sure others in work area wear safety glasses.
Safety glasses must conform to the requirements of
American National Standards Institute, ANSI Z87.1 and
provide protection against flying particles both from the
front and side.
1
TOOL SERVICE
CONDITION THAT MAY AFFECT THE TOOL'S OPERATION.
If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
CHECK SAFETY BEFORE USE. Make sure the safety
operates properly. Never use the tool unless the safety is
operating properly, otherwise the tool could drive a
fastener unexpectedly. Do not tamper with or remove
the safety, otherwise the safety becomes inoperable.
DO NOT USE TOOL IF TRIGGER DOES NOT ACTUATE
PROPERLY. Any tool that cannot be controlled with the
trigger is dangerous and must be repaired.
NEVER USE TOOL WHICH IS DEFECTIVE OR OPERATING
ABNORMALLY. If the tool appears to be operated
unusually, making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by an authorized service center.
MAINTAIN TOOLS WITH CARE. Keep the tool clean and
lubricated for better and safer performance.
NEVER CARRY THE TOOL BY AIR HOSE.
STORE TOOLS OUT OF THE REACH OF CHILDREN AND
OTHER UNTRAINED PEOPLE. Tools are dangerous in the
hands of untrained users.
PLACE TOOL PROPERLY ON WORKPIECE. Do not drive
fasteners on top of other fasteners or with the tool at too
steep of an angle; the fasteners can ricochet and hurt
someone.
DO NOT USE THE TOOL AS A HAMMER.
KEEP ALL SCREWS AND COVERS TIGHTLY IN PLACE.
KEEP FACE, HANDS AND FEET AWAY FROM FIRING
HEAD AT ALL TIMES. Never place your face, hands or
feet near the firing head.
DO NOT DISCONNECT AIR HOSE FROM TOOL WITH
FINGER ON TRIGGER. The tool can fire when reconnected to an air supply.
DO NOT LOAD FASTENERS WITH TRIGGER PULLED OR
SAFETY DEPRESSED.
NEVER PLACE A HAND OR ANY PART OF BODY IN
FASTENER DISCHARGE AREA OF TOOL.
DO NOT DRIVE FASTENERS INTO THIN BOARDS OR
NEAR CORNERS AND EDGES OF WORKPIECE. The
fasteners can be driven for a way from the workpiece
and hit someone.
DISCONNECT AIR HOSE FROM TOOL WHEN:
1). Doing maintenance and inspection;
2). Turning the adjuster and top cover;
3). Attaching or removing the no-mar tip;
4). Clearing a jam;
5). It is not in use;
6). Leaving work area;
7). Moving it to another location;
8). Handing it to another person.
Never attempt to clear a jam or repair the tool unless you
have disconnected air hose from the tool and removed
all remaining fasteners from the tool. The tool should
never be left unattended since people who are not
familiar with the tool might handle it and injure
themselves.
USE ONLY ACCESSORIES THAT ARE IDENTIFIED BY THE
MANUFACTURER FOR THE SPECIFIC TOOL MODEL
USE OF UNAUTHORIZED PARTS OR FAILURE TO FOLLOW
MAINTENANCE INSTRUCTIONS MAY CREATE A RISK OF
INJURY
USE ONLY THE LUBRICANTS SUPPLIED WITH THE TOOL
OR SPECIFIED BY THE MANUFACTURE.
TOOL SERVICE MUST BE PERFORMED ONLY BY
QUALIFIED REPAIR PERSONNEL.
AIR SOURCE
NEVER USE OXYGEN OR OTHER BOTTLED GASES AS A
POWER SOURCE. Explosion may occur. Combustible
gases and other bottled gases are dangerous and may
cause the tool to explode.
DO NOT EXCEED MAXIMUM RECOMMENDED AIR
PRESSURE MARKED ON THE TOOL. Use only clean, dry,
regulated, compressed air within the rated pressure
range marked on the tool. Never connect the tool to
pressure as which potentially exceeds 200PSI the tool
can burst.
DO NOT ABUSE THE AIR HOSE. Protect all hoses from
kinks, restrictions, solvents or sharp objects. Keep air
hose away from heat, oil, sharp edges or moving parts.
Replace damaged hoses immediately. Damaged hoses
can burst or whip around.
CHECK ALL FITTINGS, HOSES, PIPES, CONNECTIONS
AND COMPRESSOR BEFORE EACH USE OF THIS TOOL.
Repair or replace damaged or leaking hoses and
connections immediately. Damage to a hose or
connection can cause a pressure hose to break and whip
around the work area, and can lead to injury.
2
FUNCTIONAL DESCRIPTION AND SPECIFICATIONS
WARNING
Disconnect the tool from the air source before making any adjustments, changing accessories or storing the tool. Such
precautionary safety measures reduce the risk of unintentional tool operation.
FIG. 1
Adjustable Exhaust
Deflector
Air Cap
Hand Grip
Trigger
Air Plug
Body
Depth of Driver
Adjustment
Limit Pin
Quick Release
Lever
Magazine
Pusher
Safety
Fastener Type
SPECIFICATIONS
0.425”
(10.8mm)
Product Size:
Length - 14.37"(365mm)
Height - 12.01"(305mm)
Width - 3.78"(96mm)
Weight: 5.28Ibs(2.40kg)
Normal Operating Pressure: 70-110PSI(0.5-0.75MPa)
Magazine Capacity: 140pcs
Firing Mode: Sequential Fire
Fastener Size Range:
16 Gauge Staples: 3/4" - 2"(19-50mm)
3
0.063”
(1.6mm)
3/4”
19mm
2”
50mm
0.055”
(1.4mm)
FEATURES
If the tool is not used with an in-line lubrication system on
the air supply it is necessary to periodically lubricate the
tool with air tool lubrication.
360 adjustable exhaust.
Allows user to direct air away from debris.
Tool-free depth adjustment.
Quick release latch for jam.
More powerful and light weight.
Under low use, lubricate once a day. Under heavy use,
lubricate twice a day. To lubricate, insert 2-3 drops of
lubricant into the air supply fitting attached to the tool
handle (FIG 2). Using too much oil will cause it to collect in
the tool and be noticeable in the exhaust.
ASSEMBLY/INSTALLATION
FIG. 2
Follow the instructions below to prepare your tool for
operation.
1. All tool operators and their immediate supervisors must
become familiar with the operator safety instructions
before operating the tool.
2. Included with each tool are one copy of these
Operating/Safety Instructions. Keep this publications for
future reference.
3. Install a filter, regulator, lubricator unit and moisture trap
on your air delivery system per the manufacturer's
instructions for these devices. Additionally, install a
pressure gauge as close as practical to the tool,
preferably within 10 feet.
4. Select hoses with a minimum inner diameter of 1/4
inches and a maximum length of 100 feet.
2-3 Drops of
Air Tool Lubricant
Do not use detergent oil, WD-40, transmission fluid, motor
oil, or other lubricants not specifically designated as air tool
lubricants. These lubricants will cause accelerated wear to
the seals, o-rings, and bumpers in the tool, resulting in
poor tool performance and frequent maintenance.
WARNING
ADJUSTING AIR PRESSURE
To reduce the risk of injury from a hose bursting, select
hoses that are rated at least 200PSI.
5. Select fittings that are appropriate size for the selected
hoses. The tool and air hose must have a hose coupling
so that all pressure is removed from the tool when the
coupling joint is disconnected.
Adjust the air pressure at recommended operating
pressure 70-110PSI according to the length of nails and
the hardness of workpiece.
The correct air pressure is the lowest pressure which will
do the job. Using the tool at a higher than required air
pressure unnecessarily over stresses the tool. Don't exceed
110PSI.
WARNING
Never use non relieving couplers and/or female quick
disconnect couplings on the tool. Non relieving couplings
and female couplings will trap high pressure air in the tool
when the air line is disconnected. This will leave the tool
charged with enough air after it has been disconnected to
drive a nail. Only MALE pneumatic type air connectors
should be fitted to the tool, so that high pressure air in the
tool is vented to atmosphere as soon as the air line is
disconnected.
6. Set the regulator at the air delivery system to a PSI that
falls within the tool's operating range of 70-110PSI. The
correct pressure is the lowest pressure that will do the
job.
FIG. 3
70PSI Minimum
110PSI Maximum
CONNECTING AIR SUPPLY
WARNING
Never use oxygen or other bottled gases as a power source.
Explosion may occur. Combustible gases and other bottled
gases are dangerous and may cause the tool to explode.
OPERATION
WARNING
Never connect the tool to an air source that is capable of
producing air pressure exceeding 200PSI. Excessive
pressure can cause abnormal operation or cause the tool to
burst, resulting in personal injury.
LUBRICATION
WARNING
USE ONLY THE AIR TOOL LUBRICANTS SUPPLIED WITH
THE TOOL. Do not use other lubricants as they may
damage the tool.
4
WARNING
Do not exceed maximum recommended air pressure marked
on the tool. Verify prior to using the tool that the air source has
been adjusted within the rated air-pressure rang. Be sure the
air pressure gauge is operating properly and check it at least
twice a day. Tools operated in excess of their maximum
pressure rating may operate abnormally or burst resulting in
personal injury.
To connect the tool to the compressor only use pneumatic air
hoses that meet the following criteria:
1. Minimum hose pressure rating, 200PSI.
2. Minimum hose inner diameter, 1/4 in.
3. Maximum hose length, 100 ft.
FIG. 4
against the wood.
THE TOOL MUST NOT OPERATE.
4. Separate the safety from the wood. Next, point the tool
downward, pull the trigger and then wait in that position
for 5 seconds or longer.
THE TOOL MUST NOT OPERATE.
5. 1). Without touching the trigger, depress the safety
against the workpiece. Pull the trigger.
THE TOOL MUST OPERATE
2). Hold the trigger back while separating the safety
from the wood.
The tool will remain in operated status(the driver blade
will remain at the bottom).
3). Remove the finger from the trigger.
Tool operation will end (the driver blade will return to the
top).
6. If no abnormal operation is observed, you may load
nails in the tool. Drive nails into the workpiece that is the
same type to be used in the actual application.
THE TOOL MUST OPERATE PROPERLY.
NAIL LOADING
WARNING
Connect the air supply:
Snap the air hose onto the quick connector.
Check for air leakage. If leakage is noted, stop using the
tool immediately and performed by qualified repair
personnel.
Be sure the air pressure gauge is operating properly and
check it at least twice a day.
TOOL TESTING
DANGER
OPERATORS AND OTHERS IN WORK AREA MUST WEAR
SAFETY GLASSES WITH SIDE SHIELDS WHICH CONFORMS TO
ANSI Z87.1 SPECIFICATIONS.
When loading the tools magazine, check that the nail tips
contact the wear rail and slide smoothly against the surface
of the magazine. If the nails are not loaded properly, the
tool will misfire and nails can be deflected, causing the tool
to react in an unexpected manner, and damage the tool.
1. Connect air supply.
2. Pull the Pusher backward to the place of the Limit
Pin(FIG 5).
3. See tool specifications to determine appropriate nail
sizes. Insert appropriate nail strips(FIG 6). Push the nail
strip against the nose.
4. Press the Limit Pin, and the Pusher can be forward
against the nail strips automatically.
FIG. 5
WARNING
NEVER USE TOOL UNLESS SAFETY IS OPERATING
PROPERLY.
Before actually beginning the nailing work, test the tool by
using the check list below. Conduct the test in the following
order.
If abnormal operation occurs, stop using the tool and
performed by qualified repair personnel immediately.
Limit Pin
1. Disconnect air hose from tool. Remove all nails from
tool.
ALL SCREWS MUST BE TIGHTENED. If any screws are
loose, tighten them.
THE SAFETY AND TRIGGER MUST MOVE SMOOTHLY.
2. Adjust the air pressure to 70PSI, connect the air
hose.Do not load any nails in the tool.
THE TOOL MUST NOT LEAK AIR.
3. Remove the finger from the trigger and press the safety
Pusher
PULL BACKWARD
5
Stapler
16Ga.
FIG. 6
4).Open the petcock on the air compressor tank to drain
any moisture.
PRESS
COLD WEATHER OPERATION
WARNING
PUSH FORWARD
DO NOT USE A FROZEN TOOL. Allow tool to thaw before
using. Moisture frozen in the tool may impede internal
components resulting in the risk of injury and/or tool
damage.
When using the tool in cold conditions the tool will cycle
slower than usual while driving the first nails. The cycle rate
will increase as the tool warms up. Keep tool warm to avoid
reduced cycle rate.
Limit Pin
Pusher
WARNING
KEEP THE TOOL POINTED AWAY FROM YOURSELF AND
OTHERS WHEN LOADING FASTENERS. FAILURE TO DO
COULD RESULT IN POSSIBLE SERIOUS PERSONAL INJURY.
ADJUSTING THE NAILING DEPTH
WARNING
NEVER LOAD FASTENERS WITH THE WORKPIECE
CONTACT OR TRIGGER ACTIVATED. DOING SO COULD
RESULT IN POSSIBLE SERIOUS PERSONAL INJURY.
Disconnect the tool from the air source before making
adjustments. Such precautionary safety measures reduce
the risk or unintentional tool operation.
1.Disconnect tool from air supply.
2.Remove nails from the tool.
3.Adjust tool driving depth:
To reduce the nail depth , turn the adjustment knob
Counter clockwise (FIG 7).
To drive the nail deeper, turn the adjustment knob
clockwise (FIG 8).
4.Reload nails as described in the "Loading Nails" section
of this manual.
5.Reconnect air supply.
REMOVING THE NAILS:
1. Disconnect air supply.
2. Press magazine latch and pull magazine to open
position(FIG 5).
3. Grasp the head of the nail strip and remove it from
magazine.
METHODS OF OPERATION
FIG. 7
This tool is equipped with the safety and does not operate
unless the safety is depressed.
The methods of operation to drive nails with this tool is
sequential actuation mechanism.
Flush
Too Deep
1).Position the nail outlet on the workpiece with finger off
The trigger.
2).Depress the safety firmly until it is completely
depressed.
3).Pull the trigger to drive a nail.
4).Remove finger from the trigger.
Turn the adjustment knob counter clockwise
To continue nailing a separate location, move the tool
along the wood, repeating steps (2-4) as required.
FIG. 8
Too Shallow
Always handle nails and package carefully. If nails are
dropped, collating bent may be broken, which will cause
mis-feeding and jamming.
After nailing:
1).Disconnect air hose from the tool.
2).Remove all nails from the tool.
3).Supply 5-10 drops of pneumatic tool lubricant into
the air plug on the tool.
Turn the adjustment knob clockwise
6
Flush
ADJUSTING THE EXHAUST
The direction of the exhaust vent can be changed by turning
the top cover (FIG 9).
FIG. 9
WARNING
Do not attempt to clean by inserting pointed objects through
openings. Sharp edges may damage internal components
and cause a serious hazard.
Ventilation openings, the work contact element, and the
trigger must be kept clean and free of foreign matter.
Periodically clean the tool with compressed air.
Clean the magazine. Remove metal or wooden chips which
may have accumulated in the magazine. Periodically clean
magazine with compressed air.
STORAGE
WARNING
Keep out of reach of children and personnel unfamiliar with
tool operation. Lock the storage area. Tools are dangerous
in the hands of personnel unfamiliar with the tool.
MAINTENANCE
JAM CLEARING
If a nail becomes jammed in the tool, disconnect the air hose
and keep the tool pointed away from you while clearing the
jam.
1. Disconnect the tool from the air supply.
2. Open the Nose Part, and remove the jammed fasteners,
using pliers if necessary.
3. Reconnect the tool to the air supply.
4. Reload the tool with nails.
FIG. 10
Nose part
CLEANING
WARNING
When cleaning a tool be careful not to disassemble any
portion of the tool since internal components may be
misplaced or safety components may be improperly
mounted. Certain cleaning agents such as gasoline, carbon
tetrachloride, ammonia. etc. may damage plastic parts and
o-rings.
7
When not in use, the tool should be disconnected and
stored in the storage case in a warm and dry place. When
tool will not be in use for an extended period, apply a thin
coat of the lubricant to the steel parts to avoid rust.
Do not store the tool in a cold weather environment.
HOOKUP INSTRUCTIONS FOR
TOOL TO AIR SUPPLY
For better performance, install a 3/8 inch quick plug(1/4
inch NPT threads) with an inside diameter of 0.315 inch
(8mm) on the nailer and a 3/8 inch quick coupler on the air
hose.
1. With ON/OFF switch in OFF position, plug compressor
into electrical outlet.
2. Close pressure regulator by turning all the way to the
left. Turn compressor ON and let it pump all the way up
to automatic shut-off pressure.
3. Attach air hose to regulator outlet. Adjust pressure
regulator by turning to the right so that outlet pressure is
between 70PSI to 110PSI.
4. Load fasteners into nailer.
5. Point the nailer in a safe direction while attaching to air
hose.
6. Nailer is ready for use. You may need to adjust outlet
7. pressure to achieve proper fastener depth.
RECOMMENDED
HOOKUP
MINIMUM COMPONENTS
REQUIRED FOR HOOKUP
Air compressor: The air compressor must be able to maintain a minimum of 70PSI when the nailer is being used. An
inadequate air supply can cause a loss of power and inconsistent driving.
Pressure regulator: A pressure regulator is required to control the operating pressure of the nailer between 70PSI and
110PSI .
Air supply hose: Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure
from the power source, or 150PSI, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch air hose for
50 feet, run or longer.
TROUBLE SOLVING
PROBLEMS
POSSIBLE CAUSES
SUGGESTED SOLUTIONS
Air leaking near the top of
the tool or in the trigger
area.
1. Loose screws.
2. Worn or damaged O-rings or seals.
1. Tighten screws.
2. Install overhaul kit.
Air leaking near the bottom
of the tool.
1. Loose screws.
2. Worn or damaged O-rings or seals.
1. Tighten screws.
2. Install overhaul kit.
Tool does nothing or
operates sluggishly.
1. Inadequate air supply.
2. Tool is too dry.
3. Exhaust blocked.
4. Worn or damaged O-rings or seals.
1. Make sure the air compressor is set
between 70PSI and 110PSI.
2. Add about 2-3 drops of lubrication into
the air connector.
3. Clean exhaust channel.
4. Install overhaul kit.
Fasteners are jammed in
the tool frequently.
1. Driver channel is worn.
2. Piston is broken or worn.
3. Bent fasteners.
4. Dirty magazine.
5. Loose magazine.
6. Wrong fasteners.
1. Fix the drive channel.
2. Replace the piston.
3. Remove the bent fasteners, replaced with
the right fasteners.
4. Clean magazine.
5. Tighten screws.
6. Verify that fasteners are the correct size.
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising