3-wire fluorescent dimmer modules

3-wire fluorescent dimmer modules
3-WIRE FLUORESCENT DIMMER MODULES
OPTIO 3-WIRE FLUORESCENT DIMMER MODULES
INSTALLATION INSTRUCTIONS
277VAC
120VAC
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR THE END USER. DO NOT DISCARD.
OPT22000F - DUAL 2000VA 3-WIRE FLUORESCENT DIMMER MODULE
OPT22000F15 - DUAL 1800VA 3-WIRE FLUORESCENT DIMMER MODULE
FOR USE IN OPTIO LIGHTING CONTROL PANEL MODELS OPT3120, OPT6120, OPT9120
OPT24000F7 - DUAL 4000VA 3-WIRE FLUORESCENT DIMMER MODULE
FOR USE IN OPTIO LIGHTING CONTROL PANEL MODELS OPT3277, OPT6277, OPT9277
WARNING: Before installation, disconnect power at circuit breakers or remove fuse to avoid electrical
shock or damage to the unit. It is recommended that an electrician perform this installation.
THREE YEAR LIMITED WARRANTY
The Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period of three years form the date of original retail purchase, to be
free from defects in materials and workmanship. If during the warranty period you believe the purchased product or any part thereof has such a defect, you must return the product (or part) at your cost during such period, with proof of
purchase (or if installed by a third-party a written explanation of installation transaction with proof of date), to Philips Controls, 2828 Trade Center Dr. Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips Controls
supplier which agrees in advance to handle the return and replacement by factory authorization). If the product or part is found by Philips Controls to have been defective in material or workmanship it will be repaired or replaced (as deemed
necessary by Philips Controls), and the replacement will be returned to you free of charge. The original user is solely responsible for any costs associated with removal and re-installation of the product and shipping to Philips Controls or its
authorized supplier.
PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE, AND OTHERWISE DISCLAIMS ALL IMPLIED WARRANTIES
WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties so you should consult your state law if you have a questions regarding this limitation and disclaimer. Philips Controls disclaims any
and all liability for incidental, consequential, special or indirect damage arising out of any claimed breach of warranty or otherwise. However, some states do not allow exclusion or limitation of such damages, so this disclaimer may not apply to
you.
The remedy provided in the Limited Warranty for defective products is the user’s sole and exclusive remedy, subject to your state law. Further, this Warranty gives the user specific legal rights, and the user may also have other rights which may vary
from state to state.
If you believe warranty claim is warranted, you may contact your nearest authorized Philips Controls supplier. If one does not exist in your area, please contact Philips Controls Customer Service at the above address (or at 1-800-526-2731), or
please visit us at www.philipslightingcontrols.com.
Made in U.S.A.
Technical/Sales assistance: 1-800-526-2731
P/N 85-6358B
Product
Specifications
Installation
MHPWDC2020H
Instructions
3-WIRE FLUORESCENT DIMMER MODULES
Figure 1: Installing Modules and Blank Covers
Description
The Optio 3-Wire Fluorescent Dimmer Modules offer reliable dimming of 3-wire phase control
dimming ballasts where two wires are used for hot and neutral, and a third wire carries the phase
control signal. (For control of Lightolier Controls PowerSpec HDF dimming ballasts, use an Optio
"HDF" series module).
All Optio Dimmer Modules have identical mounting dimensions, allowing them to be easily swapped
within any of the Optio Lighting Control Panels. (Use caution to ensure that quad dimmer modules
are not installed into module spaces wired for dual dimmer modules.)
WARNING: Installing the module with power applied to the cabinet may expose you to
dangerous voltage and damage the device. Remove power before installing. A qualified
electrician should perform this installation.
Blank Cover
Screw (4)
Focus Button
& Status LEDs
Installation Procedure
Any combination of Optio dimming and relay modules may be installed in the Lighting Control Panel.
Blank covers MUST be installed in any unused spaces. Pull the jumper (shorting plugs) before
installing.
To install modules:
1. Unpack module and recycle or properly discard packaging materials. (Be sure to keep this
instruction sheet for future use.) Inspect dimming module for signs of damage during transit.
2. Disconnect main power to Optio Lighting Control Panel.
3. Open dimmer module side of panel front cover.
4. If present, remove blank cover from location where module is to be installed (Figure 1).
When possible, lower modules should be installed first.
5. Remove shorting plugs from the load terminal block. (The shorting plug is the red tab
protruding from the green load terminal block. To remove, grasp the shorting plug and
gently pull.) Note: The dimmer module will not operate properly if the shorting plug
is left in circuit.
6. Gently insert module into lighting control panel, heatsink first. Secure module using four
screws (provided). Dimmer Module should be installed with the heatsink facing away from
you. Note: The connectors of 277VAC Optio modules are keyed, preventing the insertion
of modules into panels of the incorrect voltage. Do not force modules into slots.
7. Connect control wire from fluorescent dimming ballast to appropriate terminals on panel.
8. Close panel front cover.
Operation
Optio Dimmer Modules are
equipped with a "Focus Button" on
each circuit (Figure 1). Tapping
the focus button quickly will turn the
circuit on to full, tapping it quickly
again will turn the circuit off.
Pressing and holding the focus button will ramp the dimmer up to full
intensity. If the focus button is
released before reaching full intensity, the dimmer will stop at that relative output.
Screw (4)
Status LED Indications:
Red LED
Green LED
Off
Flashing
Slow Flashing
Off
Off
Off
Fast Flashing
Philips Lighting Controls
On
Flashing
2828 Trade Center Drive, Suite 130B
Carrollton, Texas 75007
Off
On
Off
Off
Flashing
Condition
Normal
No Load
Focus Mode
(controlled at dimmer)
Overload
Over Temperature
Communication Error
Miswire to Line
Dimmer
Module
NOTE: The Optio 9-Module
Panel is used to illustrate the
installation. However, the
module installation is identical
for all Lighting Control Panel
models.
Load Terminal Block
Terminal
Shorting
Plug
DETAIL
Figure 2: Ballast Wiring Connections
TERMINAL A
TERMINAL B
Switched A
Leg (Hot)
Switched B
Leg (Hot)
Dimmer A
Control
Dimmer B
Control
Electrical Specifications
Operating Voltage: 120VAC, 50/60Hz
Number of Circuits: 2
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit):
OPT2200F: 2000VA
OPT22000F15: 1800VA
Operating Voltage: 277VAC, 60Hz
Number of Circuits:
OPT24000F7: 2
Min. Rated Load (per circuit): 35W
Max Rated Load (per circuit):
OPT24000F7: 4000VA
Supported Load Types: 3-Wire Phase Control Fluorescent
dimming ballasts
Cooling: Natural convection
Ambient Operating Temp: 0 to 40 degrees C
Relative Humidity: 5 to 95% (non-condensing)
Technical/Sales assistance: 1-800-526-2731
Made in U.S.A.
www.philipslightiingcontrols.com P/N 85-6358B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement