automatic paper folding machine

automatic paper folding machine
AUTOMATIC
PAPER FOLDING
MACHINE
OPERATORS MANUAL
Morgana Systems Limited
Snowdon Drive Winterhill
Milton
Keynes Buckinghamshire MK6 1AP United Kingdom Telephone:
( 01908 ) 608888
Facsimile: ( 01908 ) 692399
ISSUE
APRIL 2001
90-013
K
I
A
Z
C
FIXED SIDELAY
B
E
F
AA
A
Y
CC
DD
R
BB
Q
X
D
G
P
T
U
V
W
S
EE
FF
PAPER FOLDING MACHINE
PAGE 2
PA P E R
OPERATORS INTRODUCTION TO THE MORGANA DOCUFOLD
The Morgana Docufold is a brand new concept paper-folding machine. Designed to be used in
today's environment of document production, the Morgana Docufold can be used by non-skilled
personnel by following this easy to use operators guide. There are very few operator
adjustments required on the machine and our KWIK START section will get you started very
quickly, but we do recommend that you take a little time to read this manual, to ensure that you
fully understand the machine. We have also included a TIPS & TROUBLE SHOOTING
section. Be sure to read this section before calling a service engineer to avoid any unnecessary
expense.
On the Docufold the fold plates and Delivery Roller will move automatically according to the
type of fold selected. Please be aware that different weights, humidity, temperature or the grain
direction of the paper may make the paper fold in a different position according to the material.
Some manual adjustment may sometimes be necessary to obtain the exact fold plate position for
each type of paper.
KWIK START GUIDE:
1. Set the paper gate gap (knob B) to two thickness of the paper to be folded.
2. Place the paper to be folded onto the loading table against the fixed side lay.
3. Unclamp the moving side lay (knobs A) and slide up against the side of the paper but allow
approximately a 1/2 mm or 1/64 inch gap between the moving side lay and the paper.
4. Clamp the backstop (F) onto the moving side lay at the back of the paper stack.
(Note) Do not attempt to load too many sheets onto the loading table during set up as this
may affect the feeding operation.
5. Make sure you have power to the machine and that knob (S) is turned onto the ON position.
6. Push switch (W) downward to set up position.
7. Slide the sheet-measuring device (BB) up to the block of paper to be folded.
8. Look at the diagram on the moving side (G) lay showing the various fold types. Select the
type of fold that you require to make by turning knob (V), for example select SL for Letter
fold.
9. Lift switch (W) to the middle position (Run)
10. Press the system switch (T) and allow the machine the machine a few seconds to reach its
optimum speed.
11. Press the feed switch (U) down to pulse and the machine will feed three sheets for checking.
FOLDER
PAGE 3
12. ‘Check’ will appear on the control panel display. If the check sheets are folded correctly,
move the feed switch (U) to the off position.
13. Zero the counter by pressing the set-up switch (W) upwards. If you require to batch, the
Docufold provides the facility to batch in denominations of 10’s from 10 to 1000.
To set batch, you can select the requires batch number by turning the feed switch (U) to off
& then rotating the select knob (V) until the required batch quantity appears in the control
panel display.
14. Push the feed switch down to pulse to start the machine feeding the paper.
PAGE 4
PA P E R
MORGANA DOCUFOLD OPERATOR INSTRUCTIONS
SIDE LAY
Place a single sheet of the job onto the loading table.
Release the side lay clamp screws (A) and slide the side lay just up to the sheet so that there is
about half a millimetre clearance or 1/64 inch
Tighten the clamp screws.
PAPER GATE
Adjust the height of the paper gate using knob (B) (clockwise to lower, anti-clockwise to raise)
so that the clearance above the vacuum roller is two thicknesses of the paper to be folded. Do
not make this adjustment, when the face of the paper gate is above a hole in the vacuum roller,
if it is, rotate the vacuum roller by hand to bring the metal between holes below the paper gate.
On this machine, the paper gate is fixed in an optimum position and cannot be moved
backwards and forwards (horizontally).
SUCTION OPENING
The suction slot inside the suction drum, may be adjusted by releasing knob (C) and swinging
the knob in the desired position. Lighter stocks including bond will run best with the knob set
to the left. For heavier stocks and curled-up stock, move the knob (C) to the right until a
satisfactory position is obtained.
AIR DISTRIBUTION KNOB (D)
Depending on the length of the sheet, the air distribution knob (D) should be rotated to supply
the air to the correct ports as follows Position 1 - This is for short sheets A5 or 8" long with only port 1 open
Position 2 - This is for sheets A4 or 11" long with the front port and port 2 open
Position 3 - This is for the longest sheets A3 or 17" with the front port and port
3 open.
Position 0 - In this position, only port 2 is open and can be used on long sheets
with the curl up where you need to blow air into the centre of the stack.
These setting positions are only a guide and some experimentation may obtain a better result
with non-standard settings.
(Note) Position 1 feeds most paper stocks and sizes; thus the air distribution knob can be
left in this position for most jobs.
FOLDER
PAGE 5
AIR SEPARATION KNOB (E)
This knob controls the amount of air that is fed to the paper. The machine would normally run
with this knob set at the 'High' position. If the machine is run with less than approximately 20
sheets on the loading table, or running the job to the last sheet, this knob should be set to the low
position.
BACK STOP (F)
This is placed up to the end of the paper stack and clamped to the moving side lay (G).
SHEET MEASURING (BB)
When pushing set-up switch (W) down to set-up, the position of the sheet-measuring device will
be displayed on the control panel display. It will measure the length of a stack of paper to an
accuracy of 0.1 mm. By pushing the sheet-measuring device up to the back of the stack of paper,
it will allow the Docufold to calculate the fold length according to the type of fold selected.
Note: - If the digit after the decimal place flashes, it is measuring between 0.1 of a millimetre and
is not a malfunction. Always push the sheet-measuring device against the paper stack when
adjusting fold types.
FOLD PLATES
ALWAYS UNPLUG POWER CONNECTIONS BEFORE REMOVING FOLD PLATES.
Fitting
Fit the fold plates into their respective positions (long fold plate upper and short plate lower), by
locating the front pins (I) into the long slots and carefully sliding forwards (without twisting)
until the rear pins can be located into the short slots. When fully in position, pull down the fold
plate to lock into position. Connect the push-in power connectors – short lead to plate 1 (upper)
& long lead to plate 2 (lower).
Settings
The fold plate lengths are set automatically.
Fold plate Tilt
See roller tilt.
PAGE 6
PA P E R
Manual & Fine Adjustment
The fold plate length can be adjusted manually. You may need to make this adjustment to
achieve the exact correct length of fold. Button (CC) will select the upper fold plate & button
(DD) the lower fold plate. To make a manual adjustment to the position of the upper fold plate,
press and hold the upper fold plate button (CC). The dimension of the upper fold plate will now
be displayed in the control panel.
Note: - The upper fold plate shows the dimension of the front edge of the paper to the first fold,
the lower fold plate shows the dimension from the first fold to the second fold.
By turning the select knob (V) whilst still pressing and holding the upper fold plate button (CC)
the fold length of the upper plate can be lengthened or shortened. Turning the select knob (V)
clockwise will lengthen the fold plate length and by turning anti-clockwise it will shorten the
fold plate length.
The digits before the decimal point shown in the display are in millimetres, each ‘click’ of the
select knob (V) represents increments of 0.1 of a millimetre.
To adjust the position of the lower fold plate, press & hold the lower fold plate button (DD) and
adjust the length as described above.
When you have adjusted the fold length dimension, move switch (W) up to the Run position.
The plates will then position themselves according to the fold lengths you have selected.
With switch (W) in the Run position the left hand side of the control panel will display the letter
‘U’ which indicates a user setting followed by a letter that indicated the fold type. For example
the letters ‘UL’ would indicate a User setting based on a Letter fold and the letters ‘UH’ would
indicate a User setting based on a Half fold.
To check the fold position after making a manual or fine adjustment, press the system switch
(T) and then press the feed switch (U) down. The machine will feed 3 check sheets and stop.
After checking the 3-rd sheet, if the fold position is correct, move the feed switch up to the off
position and then immediately down to the pulse position and the machine will start to operate.
If after checking and further plate positioning is required, repeat the above procedure.
The final fold plate and delivery stacker settings can be ‘stored’ for retrieval at a later date, see
‘To Store A Programme’.
FOLDER
PAGE 7
Roller Tilt
Lever (AA) should always be set in the ‘0’ (square) position. To adjust folding out of square
you can move the roller assembly in the + or – direction by releasing knobs (Y) and moving
lever (AA) – always re-tighten Knobs (Y).
+
PAGE 8
-
PA P E R
Stacking Roller
The stacking roller will adjust automatically according to the fold type selected.
Manual or fine adjustment for the position of the stacker roller can be made by pressing and
holding the stacker roller button (EE) on the top of the control panel. ‘Roll’ and a digit from 1 to
9 will appear in the display panel.
The higher the number – the further down the belt stacker bed the roller will be.
To adjust the stacking roller position up or down, press the stacking roller button (EE) and turn
the select knob (V) to one of the pre-set positions 1 to 9.
You should adjust the roller position so that when the work is stopped by the stacking roller, it
lies flat on the delivery without lying on the sloping plate (R) and without the green belts
showing between the sloping plate (R) and the folded sheet.
To Store A Program
After making a manual adjustment or fine adjustment to either the upper fold plate, lower fold
plate or the stacking roller position, you can store the setting for retrieval at a later date. This can
be useful when jobs need to be repeated.
Press switch (W) down to the set-up position, using the select knob turn until you reach a ‘P’ with
a single digit number next to it. You have from ‘P1’ to ‘P6’ to select and can store up to six
programmes. When you have selected a ‘P’ number, press and hold the feed switch (U) down
until ‘StorEd’ appears in the display panel.
To select a ‘P’ programme at a later date, press set-up switch (W) down select the relevant ‘P’
number by rotating the select knob (V) and push the set-up switch (W) to Run.
Press system switch (T) & move the feed switch (U) to Pulse.
Emergency Stop Switch (S)
This switch also serves as the main isolator. It is important that the machine is switched off at
the end of the days running, press this switch to isolate the machine. To switch back on,
rotate the switch head clockwise.
Main Switch (T)
The main switch (T) will run the whole machine. This switch incorporates a circuit that switches
off every 100 seconds whilst the feed switch U is in the off position. The main switch may
disengage seemingly at random but this is a normal function and may be instantly re-engaged.
FOLDER
PAGE 9
Feed Switch (U)
Switches the feed on and off.
Never leave in the pulse or stream position when main switch (T) is off. This switch is used
to select the type of feed, either pulse or stream. In the central pulse position the feeder pauses
between each sheet and allows a gap of 160 mm between each sheet as they enter the fold
rollers. This gap prevents sheets over lapping inside the fold plates, which lessens the chance of
static being generated and will decrease paper jams.
Zigzag / concertina, engineering and gate folds can only be run on pulse. By holding switch (U)
down, the feed mode will switch to stream feed which will feed paper with little or no gap
between the sheets. Stream feed will increase productivity but folding accuracy may be slightly
impaired. You can only use stream on letter, half or double parallel folds.
The pulse feed will cope with all types of fold including perforating.
Batch Knob (V)
The batch knob is a rotary switch and turning the knob slightly so that it moves one position
will cause the display to show the set batch quantity. Moving the knob further will change the
batch quantity in multiples of 10 up to 990. Stopping the feed in the middle of a batch will not
affect the batch. When the machine batches, the feed will stop and the display will show the
batch quantity with a series of dashes. Feeding will resume after a short period. If batching is
not required, turn the batch knob (V) until it reads 0 in the display panel. When 0 is shown after
turning batch knob (V) the counter will only total count.
Overlap
The machine has a built in system that will detect any sheet that overlaps another sheet by at
least 20mm. When this happens, feeding will stop and the main switch will switch off,
preventing serious jams and the display will show 'O-LAP'. Note that this is not a double
detector and will not detect all double sheet feeds. However the overlap system is an indication
of a tendency to double sheet feed and therefore the paper gate should be lowered slightly and
the paper stack should be fanned out more thoroughly.
Speed Control (X)
The machine has two running speeds, which are selected by the handle (X). Pushing the handle
sharply into the machine will select the fast speed. Pulling the handle sharply outwards will
select the slow speed. The slow speed is recommended when running work that is difficult to
stack, for example when perforating or folding an engineering type fold.
PAGE 10
PA P E R
PLUG-IN PERFORATOR
The plug in perforator unit is used for perforating scoring and when folding card cover
stock and should be stored on the rear stowage hooks.
ALWAYS UNPLUG POWER CONNECTORS BEFORE REMOVING FOLD PLATES
OR PLUG-IN PERFORATOR.
Remove the second fold plate and fit the catch tray in position by hooking it over the
opening for the second fold plate. The plug in perforator unit then locates the same as the
fold plate and again, take care not to twist when fitting into position. You may need to
turn the hand wheel and push the perforator unit inwards to engage the drive gear. Plug in
the lower fold plate power connector into the perforator unit. ‘PerF in’ will appear in the
display panel.
For all applications, the unit is set on the bench using the scale to indicate positions of
the blades and hubs. It is important to spread the hubs evenly across the width of the
work to reduce the risk of paper jams.
When perforating or scoring without folding, the upper fold plate must be removed
and replaced with the lower fold plate.
Ensure that the tilt roller is at zero, plug in the upper plate connector into the lower plate.
To prevent damage to the unused upper plate when scoring or perforating, store safely on
the stowage hooks at the reverse side of the machine.
Press set-up switch (W) down and then up to the Run position, the built in deflector on
lower fold plate will close automatically to the deflect position.
Note: - the Docufold will automatically recognise that the lower plate is in the upper
plate position and that the plug-in perforator unit is in the lower plate position. You do
not need to measure the paper length.
Start the machine with the main switch (T), and select slow speed by pulling out lever
(X) sharply. Press the feed switch (U) to pulse.
The machine will feed sheets for checking and will display ‘Perf 3’ if the counter has
been set to zero. To run the job switch feed (U) to off and then pulse.
Note: - Always run perforating or scoring jobs on pulse feed.
FITTING PERFORATER BLADES
The perforator blades are split into two matching halves and are fitted to the upper hubs
as shown in the drawing using the four screws supplied.
FOLDER
PAGE 11
PAGE 12
PA P E R
SCALE
22
PERFORATING BLADE
21
20
19
18
17
16
PERFORATOR STRIPPER
14
13
12
11
10
UPPER TYRE AND HUB ASSEMBLIES
9
8
7
6
5
4
3
2
1
FRAME PAD
0
UPPER PERF SHAFT
ANVIL
LOWER PERF SHAFT
LOWER HUBS (SOLID)
EDGE OF SHEET
DRIVE HUB
RECOMMENDED PERFORATOR SET - UP
SCALE
22
21
UPPER PERF SHAFT
20
19
1,0 mm
( 3/64")
LOWER PERF SHAFT
18
17
16
15
SCORER
14
13
12
11
UPPER TYRE AND HUB ASSEMBLIES
10
9
8
1,0 mm
( 3/64")
LOWER HUBS (SOLID)
7
6
1,0 mm
( 3/64")
1,0 mm
( 3/64")
5
4
3
2
FRAME PAD
1
0
1,0 mm
( 3/64")
EDGE OF SHEET
DRIVE HUB
RECOMMENDED SCORER SET - UP
FOLDER
PAGE 13
SETTING PERFORATORS
Upper and lower hubs can be positioned on the shaft by unscrewing the 2mm-grub screw.
Slide the hub with the blade attached along, the shaft into position to correspond to the
work using the scale as a guide. For example, to perforate 20mm from the edge of an A4
sheet, you would set the blade at 190mm (210 minus 20). When positioned re-tighten the
2mm-grub screw. Important - Do Not Over Tighten This Grub Screw
Slide the hub with the anvil, up to the perforator blade and the remaining upper and lower
hubs, set as the drawing, remembering to spread them to support the sheet fully across its
width.
Clip the perforator stripper adjacent to the upper hub as shown. Plug the unit into
position, fit the sheet smoother into position to hold the sheets down and run the machine
at the slow speed to check position.
Adjust the backstop and side guide to suit the work.
For work longer than the backstop will allow, remove the backstop and use the extended
backstop that is located underneath the catch tray.
There is a full range of perforator blades available as follows:
For fine perforation
For Paper
For heavier Stock
For use with blades
Slitter set for cutting
56 tooth
28 tooth
20 tooth
Anvil
-
Part Number 1.99-41
Part Number 1.99-12
Part Number 1.99-10
Part Number 1.99-35
Part Number 1.99-13
SCORING
It is possible to score work using the plug in perforator. The scorers are split in two
halves, fitted to the upper shaft and set as shown in the drawing using the scale on the
unit as a guide to position. The lower hubs are moved up to but just clear of the scoring
blade. The actual gap is critical and may require some experimentation to obtain a
satisfactory score line. As with perforating, the remaining hubs must be spread to support
the sheet fully across its width.
Scorers available:
Type A
Type B
Type D
PAGE 14
Part Number
Part Number
Part Number
6.99-05 for most card
6.99-06 for deep score
6.99-09 for paper
PA P E R
FOLDING CARD
For best results, the card material should always be printed cross grain as this causes less
resistance when folding. Pre scoring of card stock is also recommended
By using the plug in perforator unit to deliver card, the problem of the stock curling will
be minimised. Put the upper plate into the upper plate position and the plug-in perforator
unit into the lower plate position. Plug in power connectors - upper into upper fold plate
and lower into perforator unit.
Set the backstop, sheet measuring device and side guide to suit the work. Press the
switch (W) down to Set-up and then up to Run. Plate 1 will automatically move to half
the length of the stack of cover stock provided the sheet measuring device (AA) is in
position. Fine adjustments may be necessary to upper plate as described in ‘Fold Plate
Manual / Fine Adjustment’.
It is recommended that when folding card, the machine be set to batch after twenty
sheets, which will allow easy off loading. For longer runs an optional rear delivery belt
stacker (Assy. No. 9-09-01) is recommended to be used.
In the event of a paper jam, the sensor will cut out the main switch. The main fold rollers
are linked to a clutch, which will prevent sheets continuing to feed.
PAPER JAMS
If for some reason a piece of paper jams in the machine, remove and check inside the fold
plates. If there is paper jammed around the fold rollers take hold of a roller and wind
them by hand to remove the jam. If it is impossible to wind the roller by hand, remove
the roller assembly as described below. After clearing a paper jam, always check inside
the fold plate (see Fold Plate Section) to make sure no torn pieces of paper are jammed
inside the plate.
ROLLER ASSEMBLY - REMOVAL
The complete roller assembly unit can be removed from the machine simply by
unscrewing the knobs (Y) on each side and taking hold of the rear roller and lifting out
the unit. This is beneficial to clear paper jams, to clean the roller and for maintenance.
With the roller assembly removed, the safety circuit prevents the machine from running.
Replace the roller unit in the reverse sequence. Clean the rollers with a stiff brush
between the grooves using QD wash supplied by Morgana.
FOLDER
PAGE 15
ROLLER ADJUSTMENT
The unique fold roller design of your Morgana Docufold will fold most paper stocks without the
need for adjustment. If you have a requirement to fold very delicate or thicker stock or refeeding to produce a cross-fold the fold roller gap can be easily adjusted as follows: 1. Remove the roller assembly from the machine as described above.
2. Loosen the Cap Head Screw on the operators side of the roller that you wish to adjust (any
of the 3 outer rollers) using the 5 mm Bondus ‘L’ wrench provided & release the M8 lock
nut on the non-operators side with the 13 A/F spanner provided.
3. Insert the 4 mm hex ball driver into the socket screw at the end of the roller shaft and rotate
in the required direction to adjust the roller gap.
4. The graphics on the inside of the roller side plate show which way to turn the roller to adjust
the gap relative to the centre roller.
5. Re-tighten the half nuts & cap head screws to lock the roller into position.
6. Repeat procedure for each roller that you wish to adjust and then replace the roller assembly
into the machine.
7. Reset the roller tilt knob (AA) back to the zero central position and screw in the Clamping
knobs (Y).
Rotate Roller in this direction to increase Gap
(each graduation equals 0.1 mm of gap adjustment)
Centre Roller
3 Outer Rollers (Adjustable)
Section Through Roller Assembly
PAGE 16
PA P E R
SEN SO R C LEA N IN G
The sensors to detect and count the sheets are located on the end of the ball holder just
next to the fold roller unit. If the counter is failing, the sensors can be accessed for
cleaning by rem oving the roller assem bly as described above. Clean by using a soft
brush or dam p cloth.
FO L D PL AT ES - M A IN T EN A NC E
The fold plates can be opened up for m aintenance, cleaning, etc by rem oving the lock
knob (H) and rem oving the tw o bolts (Z). The fold plate w ill then open up to enable
paper jam s to be rem oved or cleaning.
FOLDER
PAGE 17
FOLDING TIPS AND TROUBLE SHOOTING:
SHEETS DIFFICULT TO FEED
Check that you have not got too many sheets in the feeder. Heavy-coated stock will not feed as
high a pile as for example 80-gsm copier paper.
Make sure the moving side lay is not pushed in too tightly against the paper. Similarly, if the
moving side lay is set too far away from the paper stack, this will allow the air to escape instead
of blowing through the paper.
Make sure that the gap under the paper gate (B) is not set too low.
Turn the Air separation knob (E) to the high position.
Make sure that air distribution knob (D) is set correctly.
If the paper width varies you may need to trim the sheets to the same size.
If the paper is curling upwards the suction drum may not be able to pull the sheet downward to
wrap around the drum for efficient feeding. You may need to bend the sheets downward prior
to loading.
DOUBLE SHEET FEEDING
Make sure the gap under the paper gate (B) is not set too high.
Make sure the air distribution knob (D) and the air separation knob (E) are at the correct setting.
In extreme cases you may need to separate the sheets prior to loading.
Make sure you run on Pulse not Stream.
FOLD IS NOT SQUARE OR CONSISTANT
Check the sheets are all exactly the same size and are square before folding as you can only fold
accurately if the material is consistent.
Make sure you have no foreign bodies such as fragments of torn paper inside the fold plates or
the fold rollers.
Check that the fold plates are locked and located securely and that the roller tilt mechanism is
set to zero and locked.
PAGE 18
PA P E R
PAPER WILL NOT STACK CONSISTENTLY:
Make sure the feed is consistent before attempting adjustments to the stacker.
Set the stacking roller position as described in the manual. Sometimes a small
repositioning of the roller will improve the stacking. See Stacking Roller.
If the paper is too curly when being delivered, place the catch tray and plug in perforating
unit with blades disengaged into position and deliver out the back. This applies to single
fold applications only. If two folds are required, you may need to reduce the weight of
stock to achieve the desired results.
PAPER WILL NOT DEFLECT WHEN USING ONE FOLD OR PERFORATING:
Check to make sure that the second plate is being used as the deflector.
Make sure that the plate is located securely and that the deflector bar is wound right to
the end.
Set the tilt roller mechanism to zero.
Check that the material is not too heavy to deflect.
TOTAL AND BATCH COUNTER NOT WORKING:
Clean the sensors as described in the manual.
O-LAP KEEPS APPEARING ON COUNTER BOARD
If the overlap keeps tripping in and cutting off the machine, first check you are not
feeding doubles and reset the feeder.
Overlap tripping can also mean that the machine is slowing slightly which may mean the
material is too heavy.
Check that you have no foreign bodies or torn paper stuck inside the plates or machine.
‘NO PLATE’ IN DISPLAY
Check fold plate or plug in perforator power connectors.
MACHINE WILL NOT RESET
FOLDER
PAGE 19
NO POWER TO MACHINE
If control panel display fails to come on, check that isolator switch (S) is not pressed in.
To release, turn knob clockwise.
Check power supply to the machine.
MAIN SWITCH CUTS OUT:
The feeder will cut out automatically after 100 seconds if the main switch is left on
without the feed switch being activated.
The compressor inside the machine requires up to 28 amps to start running. You must
have the machine plugged directly into a 30-amp ring main. Do not attempt to run the
machine with an extension lead.
The main switch will cut out if you have a paper jam or overlap is indicated.
FOLD ROLLER REPLACEMENT:
Your Morgana Docufold has been designed to make fold roller replacement an easy and
low cost operation. Your local sales agent will be able to supply you with a complete
replacement roller assembly which allows you to change the roller assembly yourself as
described in the roller assembly removal section of this manual. You will need to send
back to your agent the existing roller assembly.
PAGE 20
PA P E R
FOLDER
PAGE 21
CONTROLS
DISPLAY
INFO....
ACTION
WORK
FOLD SELECTION
STOP
Twist On
SELECT
Sh
312
Sh
297
SL
297
LETTER.
SC
297
CONCERTINA.
Sh
297
HALF.
Sd
297
DOUBLE PARALLEL.
SE
297
ENGINEERING.
SG
297
GATE.
SET-UP
0
I
P1...P6 297
SAVED USER DEFINED
(P1 THROUGH TO P6)
On
PROCESSING....WAIT
READY
PROCESSING....WAIT
PULSE
SL
51
TEST SHEETS
- 3 OFF
ChEc
3
CHECK TEST
SHEETS.
SL
3
ACCEPT IF O.K.
- IF NOT SEE OVER FOR
MANUAL ADJUSTMENT
SL
4
RUN
PULSE
PULSE
FEED - OFF
PULSE
PAGE 22
PA P E R
CONTROLS
DISPLAY
INFO....
bAt
0
bAt
50
SL
4
SL
200
ACTION
WORK
BATCH
ZERO COUNT
ZERO BATCH - 2 SECONDS
ZERO COUNT
SELECT
SET BATCH QUANTITY
READY
RUN
PULSE
PULSE & STREAM
PULSE
- ALL FOLDS
Cont on 200
STREAM
SL
200
PULSE
STREAM
- LETTER
- HALF
- DOUBLE PARALLEL
FOLD PLATE & DELIVERY
ROLLER ADJUSTMENT
MANUAL ADJUST
(BASED ON STD. FOLD)
Pt1
Pt1
SELECT
97.7
MANUAL ADJUST
(BASED ON STD. FOLD)
Pt2
Pt2
SELECT
98.9
Roller
roLL
SELECT
UL
SELECT
SET - UP
FOLDER
10
P1...P6
READY
P5
NOTE DISPLAY CHANGE
U = USER SETTING
L = FOLD TYPE
CHOOSE STORE AREA
(P1 THROUGH TO P6)
STORE
StorEd
PROGRAM
PULSE
1
MANUAL ADJUST
(BASED ON STD. FOLD)
47
RUN
PAGE 23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising