CONTENTS
1. Product Features………………………………..………………..….2
2. Product Specifications……..………………………………………3
3. Overall Performance………………………………………………..4
4. Protection………………………………………………………………..4
5. Dimensions……….……………………………………………………..5
6. Cables & Connectors………………………………………………..5
7. Precautions………………………………………………………………6
8. Information………………………………………………………………7
9. Installation………………………………………………….……………7
10. Troubleshooting….………………………………………………….8
1
1. Product Features a. Stable and reliable b. Cosmic black casing c. Supports single 12v output for higher power usage d. Supports ATX 12v 2.3 version e. Supports Dual/Quad Core CPUs f. All cables are sleeved g. Built in 1 x 13.5cm extremely silent automatically thermal fan
speed controlled blue LED fan h. Dimensions:
150mm / 5.91” (W) x 158mm / 6.22” (L) x 86mm / 3.39” (H) i. Heavy duty protections including OVP (Over Voltage Protection)
, OPP (Over Power Protection), UVP (Under Voltage Protection)
and SCP (Short Circuit Protection) j. Universal AC input by active PFC (99%PF Typical) k. Double Forward Converter Design
2
2. Product Specifications:
a. AC input voltage: 115-230V b. AC input frequency: 60Hz/50Hz c. Operating temperature: The power supply should be operated in an ambient temperature of 0°C to 40°C d. DC output:
Model
AC Input
DC Output Voltage
Max Output Current
Combined power
Total Power
Model
AC Input
DC Output Voltage
Max Output Current
Combined power
Total Power
Model
AC Input
DC Output Voltage
Max Output Current
Combined power
Total Power
ATX‐JP600W
+3.3V
115‐230VAC , 8A/4A , 50‐60HZ
+5V
20A
120W
20A
+12V
44A
528W
‐12V
0.3A
+5Vsb
2.5A
3.6W 12.5W
600W
ATX‐JP800W
+3.3V
115‐230VAC , 8A/4A , 50‐60HZ
+5V
20A
120W
20A
+12V
58A
698W
‐12V
0.3A
+5Vsb
2.5A
3.6W 12.5W
800W
ATX‐JP1000W
+3.3V
115‐230VAC , 10A/5A , 50‐60HZ
+5V
20A
120W
20A
+12V
74A
888W
‐12V
0.3A
+5Vsb
2.5A
3.6W 12.5W
1000W
3
3. Overall Performance:
a. Total output power: full load at normal line input voltage. b. Hold up time: 17ms at full load normal line input voltage. c. Switching frequency: 50KHz at normal line input. d. Stability: +/- 5% for 24KHR after warm up.
4. Protection:
a. Under voltage protection.
If an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state when +12V, +5V & +3.3V outputs under 60% of its maximum value. b. Over voltage protection output
+12 VDC
+5 VDC
+3.3 VDC
Minimum
13.4
5.70
3.70
Nominal
15.0
6.3
4.2
Maximum
17
7.0
4.8
Unit
Volts
Volts
Volts
An output short circuit is defined as any output impedance of less than 0.1 ohms. The power supply shall shut down and latch off for shorting the +3.3
VDC, +5 VDC or +12 VDC rails. Shorts between main output rails and
+5VSB shall not cause any damage to the power supply. The power supply shall either shut down and latch off or fold back for shorting the negative rails. +5VSB must be capable of being shorted indefinitely, but when the short is removed, the power supply shall recover automatically or by cycling
PS_ON#. The power supply shall be capable of withstanding a continuous short-circuit to the output without damage or overstress to the unit.
4
The power supply will be shut down and latch off when output power is110%~150%
5. Dimensions:
150mm x 158mm x 86mm (5.9” x 6.2” x 3.4”) W x L x H
6. Description of Connectors:
5
7. Precautions:
Warning! To avoid the risk of electrical shock, unauthorized persons heed the following precautions: a. Do not open the power supply case! b. Before turning on, please make sure that the input voltage of the red RMS side switch on the power supply corresponds to the power voltage given in your environment.
(USA & Canada: 115V; Europe, Central and South America: 230V). c. Avoid exposure to humidity.
6
8. Information:
Thank you for purchasing a high-quality Apevia product! Please visit our website at http://www.apevia.com
for complete warranty information and future support for your product. For the latest release information, or should you have any questions, please visit our website, or contact us at:
Support Phone Number: 1-909-718-0789
Support E-mail: [email protected]
9. Installation:
7
10. Troubleshooting:
If power supply fails to operate properly, please check the following before requesting for an RMA: a. Please make sure the power supply and power cord are connected properly. b. Please make sure the power cord is plugged into the power socket. c. Please make sure the power supply I/O button is switched to the “ I ” position. d. Please check if all the connectors (motherboard, floppy and peripherals) are connected properly. e. Please allow 5 seconds interval before turning the power on again when power supply is switched off manually (setting the I/O switch to the “ O ” position)
8