PL900
DEUTSCH
ENGLISH
Hersteller
Wörlein GmbH
Gewerbestrasse 12
D 90556 Cadolzburg
GERMANY
FRANÇAIS
NEDERLANDS
Tel.: +49 9103/71670
Fax.: +49 9103/716712
Email. [email protected]
Web: www.woerlein.com
PL900
BATTERY INSTALLATION
The battery compartment is located on the back of the remote control.
1. Remove the battery compartment door by pressing in on the tab and
lifting it off.
2. Insert two (2) AAA size batteries (not included) into the battery
compartment following the polarity markings inside the battery
compartment.
3. Replace the battery compartment door.
Location of controls
1) Remote sensor
2) Standby LED indicator
3) LCD display
4) On/Off button
5) Function button
6) CD tray open button
7) CD tray
8) CD tray eject hole
9) Vol +/- button
10) Finalize button
11) CD stop
button
12) Record button
13) CD play/pause
button
14) Track separation button
15) CD Skip up / down button
16) USB
skip/tune up/ down button
17) USB play/stop/tuner band button
18) Earphone jack
19) Aux in jack
21) USB socket
22) Cassette forward/eject knob
23) Cassette slot
24) Turntable dust cover
25) Spindle adaptor
26) Alignment screw with rubber cover
27) Counter weight
28) Anti skating
29) Turntable speed selector
30) Cueing lever
31) Tone-arm lock
32) Line out jack
33) FM antenna
34) AC line cord
Remark : control location from 35-47 on remote control mentioned at last page of this I/M
Caution:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
This unit should not be adjusted or repaired by anyone except qualified service personnel.
Precautions for use
Installation
•
•
•
Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the mains voltage and before all other connections have been
made.
Do not cover any vents and make sure that there is a space of several centimeters around the unit for ventilation.
EN-1
Installation of counter weight
1.
2.
3.
4.
Slide in the counter weight completely into the rear of the tone arm until it reach the end, turn it clockwise until it click with
pit inside.
Twist the counter weight clockwise & backward until it reach the white line as figure 2
Twist the counter marking until it reach “ 1 “ position
Twist the counter weight anti-clockwise & inward until it reach the appropriate working pressure.
Remark : The working pressure of the provided stylus is from the range 4 – 6 grams. According to the cartridge manufacturer.
All stylus has it own working pressure and please refer to the specification respectively.
Connection
1.
2.
Connect the AC line cord (34) to AC outlet.
Press the On/off button (4/35) and if standby LED indicator (2) light off, it’s mean the power supply is normal. Now your
system is ready to play the music.
Setting the clock
1.
2.
3.
4.
¾
Set unit in standby mode.
Press & hold the “ MEM/CLK-ADJ ” button (44), the LCD display (3) will show “ 24 hr “press TUNE
or TUNE
button (16/44) to select the appropriate area hour format (12hr/24hr). Press “MEM/CLK-ADJ” button (44) again to
confirm.
The LCD (2) will display the first & second digit of “ 00 ” is flashing. Press TUNE
or TUNE
button (16/45) to set
the correct hour. Press “ MEM/CLK-ADJ ” button (44) to store the correct hour.
or TUNE
button (16/44) to set the correct minutes.
The third & fourth digit of “ 00 ” is flashing, press the TUNE
Then press “ MEM/CLK-ADJ ” to store the correct minute.
The pre-set time will be re-set completely if dis-connecting the main power supply. You are
recommended to switch the system into standby mode for convenience usage.
Listening to radio
Manual tuning
1.
2.
3.
4.
5.
Press the On/off button (4/35) to switch on the unit and press the function switch (5/45) to select “ Tuner “ mode.
Press and hold the TUNE
or TUNE
button (16/44) for 1-2 seconds and then release
The unit will start seeking automatically and stop until a radio station is reached.
Repeat step 2 & 3 until the desired radio station is being reached.
Adjust volume up/down button (9/42) to the desired volume level.
Preset stations
You can store up to total of 30 radio stations in the memory.
1. Set to “ Tuner “ mode
2. Turn to the desired radio station by “manual” or “auto” tuning method.
3. Press “ MEM/CLK-ADJ ” button (44) to enable program state.
button to select the desired station memory position for storage.
4. Press “ FOLDER/PRE (44) or FOLDER/PRE
5. Press “ MEM/CLK-ADJ ” button (44) again to confirm the setting.
6. Repeat step 2 to 5 to store other stations.
button at remote handset to select the preset stations in order.
7. Press FOLDER/PRE (44) or FOLDER/PRE
¾
¾
THE PRE-SET MEMORIES WILL BE CANCELLED COMPLETELY IF SWITCHING OFF THE MAIN POWER
BUTTON ON SYSTEM. YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR
CONVENIENCE USAGE.
YOU CAN OVERWRITE A PRESET STATION BY STORING ANOTHER FREQUENCY IN ITS PLACE.
FM & FM-stereo reception
z
System defaulted in stereo mode. The FM-stereo icon “ST” will light up on LCD display (3) show FM stereo program is
receiving. In particular when stereo signal are weak. It is preferable to receive the program in mono by ST/MP button on
remote control.
Hints for best reception:-
FM : The receiver has a built-in FM wire antenna (33) hanging at the rear cabinet. This wire should be totally unraveled
and extended for best reception.
EN-2
Playing compact disc
z
Getting start
1.
Press the Function button (5/45) to select “ CD “ mode. The LCD display will show “ busy “ and then “ no disc “ if the CD
compartment is empty.
Then press the CD tray open button (6) to open the CD tray (7).
Place a CD with the printed side facing up inside the tray & then close the CD door.
Focus search is performing and LCD display (3) will show “ busy “ and then display the total number of tracks & total
playing time.
2.
3.
4.
z
Play / Pause mode
1.
Press the “ CD Play/Pause
” button (13/36) to start playback, the first track will start playback.
To interrupt, press the “ Play/Pause
” button (13/36) once, the playing time will be freeze on the LCD display (3).
Press again to resume normal playback.
2.
z
Stop mode
1.
If “ CD Stop “ button (19/38) is pressed during play or pause mode. It will go to stop mode and display total number of
track on the LCD display (2).
2
z
Skip mode (skip up
1.
During play or pause mode, if “ Skip up
” button (15/37) is pressed. It will go to next track and display the track no.
and then remain the play or pause mode.
” button (15/37) is pressed. It will go back to the previous track and play
During play or pause mode, if “ Skip down
the track.
2.
/ skip down
)
Remark:-
-
Before pressing the “ CD tray open ” button (6) for changing disc. Press the “ CD stop ” button (11/38) first and
ensure the LCD resume to the original information.
The reaction time of the CD burner is longer than normal CD player due to the complicacy system.
Keep pressing with all difference function within a short time may cause mal-function of the system. Please re-start the
unit if this is happen.
The reading and playback time of CD-R(W) disc is various from brand to brand. It depends on the compatibility of the
used disc.
This device only design for normal compact disc format. Is not support any MP3/WMA format.
z
Repeat mode
-
Press the Repeat button (48) before or during playback, a single track or all the tracks can be played in difference mode as
follow:(1) repeat all track
Play mode
Repeat all
Repeat 1
Off mode
(2) repeat 1
(3) off mode
Indicator
on LCD display
1
--------------
CD disc programming
1.
2.
3.
4.
5.
6.
7.
Up to 32 tacks can be programmed for CD playing. Before use, be sure the system is at stop mode before
programming:Set in CD mode & stop the disc playback.
Press the “Program” button (46), “ Prog “ indicator will appear on LCD display (3). Moreover, it will indicate program no.
(P-xx) and digits for track no. to be programmed.
Select a desired track by pressing CD skip up
or down
buttons (15/37).
Press the “ Program ” button (46) to store the trace into memory.
Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
” button (13/36) to play the disc in
When all the desired tracks have been programmed, press CD “ Play/Pause
assigned order.
To cancel the programmed file, press “Stop” button (11/38) until “ Prog “ indicator is disappear on LCD display (3).
Remark:-
After program play and you can delete the programmed track in the order from the last one to the 1st one after the
programmed track start to played. Press stop button to set the unit in stop mode first, press “ Clear “ button at remote
control once, then press stop button to enter clear mode, press the Clear button again once by once. The programmed
track will delete one by one from the memory.
EN-3
Recording function
Apart from the CD playback function, it can perform the CD recording function either from Phono / Tape / Aux and USB mode
respectively. All the recording track will be stored at “ audio-CD “ format:Before start, place a CD-R or CD-RW disc in the CD tray (7). The disc is able to record only if the LD display show “ NO TOC
“.
Remark : CD-R disc can be recorded once only and not support erase or re-record function. The playback quality of either
CD-R(W) disc is various from differences kind of audio CD player device.
Important notices:The revolving speed of CD burner is higher than normal CD mechanism. Thus, some
mechanical noise and vibration of unit cabinet may occur during operation. This is not the
malfunction of the system.
Due to the variety on the quality and the compatibility of CD-R(W) disc from the market.
Please change other brand if you found the used one is not able to record or the
performance is not so stable.
Since the CD burner was complicate equipment, in case the power was interrupt or wrong
operation during the CD burner is running, it may cause the system will locked and cannot
eject the CD tray, switch off the power and use a stick to stab the hole which near by the
CD tray, then the CD tray will eject portion mechanically, pull out the CD tray completely
by manual and remove the disc, then re start the system again.
3
A) Recording mode
I) Phono recoding
1) Press Function button (5/45) to select “ Phono “ mode. Place the recorded vinyl & get ready for playback.
2) Press “ Rec
“ button (12/44) and then press the CD “ Play/Pause
” button (13/36) until the play indicator “
“ show on LCD display (3).
3) After few seconds, the LCD (3) will show the time counter and now the system is start recording process. Now start the
playback of the vinyl at phono.
4) After completing of recording, press the “ Stop
” button (11/38) and then stop the playback of vinyl.
II) Cassette recording
1)
2)
3)
4)
Press Function button(5/45) to select “ Tape “ mode. Place the recorded cassette tape to the cassette slot (23) to get
ready for playback.
Press “ Rec
“ button (12/43) and then the CD “ Play/Pause
” button (13/36) until the play indicator “
“ show on
LCD display (2).
After few seconds, the LCD (3) will show the time counter and now the system is start recording process. Now push the
cassette tape to the cassette compartment to start playback of which the track you prepare to record.
After completing of recording, press the “ Stop
” button (11/38) and then stop the playback of the cassette tape.
III) Aux-in recording
1)
2)
3)
Press Function button (5/45) to select “ Aux “ mode. Connect the headphone output at the audio device (such as mp3
player, CD player etc) to the 3.5mm aux-in jack (19) via a 3.5 mm connecting cable (not provided).
Repeat the same procedures from step 2 as described on other recording model from above then start playback your
external device.
Adjust the volume output level at your audio player device if the recording level is too high.
IV) USB recording
1) Press function button (5/45) to select “ USB “. Plug-in the USB pen-drive with the face up & make sure it going into
completely
2) Repeat the same procedures from step 2 as described on other recording model from above and press Play button of
USB function.
4) Adjust the volume output level at your audio player device if the recording level is too high.
Remark:The recording speed is 1:1 and according to the actual plying time of the playing source
” button (13/36), “ busy “ briefly appear on LCD and the
To suspend the recording process, press the “ Play/Pause
recording is in pause. To re-start, press again the “ Play/Pause
” button (13/36) until the play indicator “
“ show on
LCD display (3).
B) Recording setting
I) Recording level
Record level can be adjust by REC LEVEL +/- button (40) to avoid distortion once the record source level was too high.
II) Track separation
You can divide the recording music track by track during recording by auto or manual mode:-
EN-4
A) Auto mode
Press the “ Auto/Manual “ button (43) when prepare the recording function, the LCD (3) will show -20db , -30db, -40db, the
“AUTO TRACK” icon will appear on LCD“
When the recording sound level has dropped below the -20 / -30 / -40 dB (record signal) respectively, the current track will
terminate and then generate a new track & continue the recording mode automatically.
Thus, you are recommended to set lower record level for the music source with clear performance such as USB and higher
record level for higher noise music source such as vinyl:“ – 20db or – 30db “ – for recording of USB or Aux-in with digital music source
“ – 30db or – 40db “ – for recording of Tape or Phono mode
“ ------- “ – auto mode off
Remark:The above is just a recommendation, the actual performance is various and depend on difference music source time by time.
thus, if the cut-off is always mis-judge for certain music file, please use manual mode instead.
B) Manual mode
Anytime when press the “ track separate “
“ button (43) once during recording at any mode, the system will generate a
new track and continuous the recording. the word “ busy “ will briefly show on LCD display (3), it mean the unit is creating a
new track successfully.
III) Finalize a CD-R(W) disc
You must convert the CD-R(W) disc into standard CD before playing at other audio CD player. This process is knows as
finalizing and a table of contents (TOC) will written to the CD on the same time:1.Select CD function mode and place the CD-R(W) disc you are going to finalize.
2.Press the finalize button (43) during CD stop mode. “ Fin-d “ appears on the LCD display (3). (press the “ CD stop
button (11/38) to quite finalize mode if necessary)
3.Press the “ Play/Pause
” button (13/36) to start finalizing and the LCD (3) will show “ busy “ during the process.
4.After completion, the CD door will open automatically and the “ NO TOC “ indicator will disappear from LCD (3).
”
Remark:-
The time for finalizing is subject to the contents of recorded and it may take up to 15 minutes in some cases.
No button is working during finalize process.
Never turn off the power or un-plug the power cord during finalize process.
The CD-R disc cannot be recorded again after finalizing.
Although finalized CD-R disc may be played on ordinary CD players, remember that finalized CD-RW disc may not play
on ordinary CD players.
Owing to the variance of the compatibility of CD-R or CD-RW disc from the market. Please change to other one if
the recording cannot perform or you find the recording performance of existing one is not up to satisfaction.
This is not the malfunction of the system.
IV) Erase or un finalize a CD-RW disc
It is possible to erase the last recorded track or erase a whole record disc.
If erase the last track of the finalized CD-RW, must un finalized the CD-RW first
A) Un finalize a CD-RW disc
1. Set at CD function mode and place the CD-RW disc you would like to un finalize.
2. Press the “ Erase “ button (43) at CD stop mode & display will show “un Fin-d” then press the “ CD Play/Pause
”
button (13/37) to start erasing and “ busy “ disappear on the LCD (3)
3. After finish the un finalized display will show total track nr. and total playing time of the disc and “ NO TOC” indicator will
appear
B) Erase one track
4. Set at CD function mode and place the un finalized CD-RW disc you would like to delete the track.
5. Press the “ Erase “ button(43) at CD stop mode & “Er“ and the last track nr. appear on the LCD (3)
6. Press the “ CD Play/Pause
” button (13/36) to start erasing the last track and “ busy “ disappear on the LCD (3) .
7. After finish the track erasing display will show total track nr. and total playing time of the disc and “ NO TOC ” indicator will
appear
8. Repeat step 5 and 7 to continues the erasing .
C) Erase all track
1. Set at CD function mode and place the CD-RW disc you would like to delete the track.
2. Press the “ Erase “ button(43) at CD stop mode repeatedly until “ Er all “ appear on the LCD (3)
” button (13/36) to start erasing and display appear “busy” during erasing
3. Press the “ CD Play/Pause
4. The LCD (3) will show “ 0000000 “ to confirm the erase process is completed.
Remark :
-
This operation cannot be undo.
The copy CD-RW disc from other system cannot be erase one by one in this unit but may be erase all is possible.
EN-5
Playback of MP3 song via USB storage media
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media with USB connecting port (21).
1.
2.
z
3.
4.
z
Set the system at standby mode first or other function except USB mode.
Plug-in the USB pen-drive with the face up & make sure it going into completely or insert the memory card in the direction
of the arrow as shown in the label on the underside of the memory card slot. Insert straight without bending..
Connecting the USB upside down or backwards could damage the audio system. Check to be sure the direction
is correct before connection.
“ USB mode.
Press Functions button (5/45) to select “
The system will start reading the storage media automatically after connecting, and LCD display (3) will show the total
number of MP3 files being detected.
Play / pause mode
1. To interrupt, press the USB “ ” button (44) once, and the playing time will be freeze & flashing on the LCD display (3).
Press again to resume normal playback.
z
1.
z
Stop mode
Press and the USB stop
Skip mode (skip up
button (44) during play or pause mode, system will go to stop mode.
/ skip down
)
1. During play or pause mode, if “USB skip up
” button (16/44) is pressed. It will go to next track and display the track no.
And then remain the play or pause mode.
2. During play or pause mode, if “USB skip down
” button (16/44) is pressed. It will go to the previous track and change to
play mode.
5
Remark
-
-
z
The system can detect and read the file under MP3 format only though the USB port.
If connect the system to MP3 player via the USB socket, due to variances in MP3 encoding format, some MP3
player may not be able to play via the USB socket. This is not a malfunction of the system.
USB port does not support connection with USB extension cable and is not designed for communication with
computer directly
MP3 track format requirement:MP3 bit rate : 32 kbps~256 kbps.
The performance of playing MP3 file is various from the quality of recording disc and the method of recording.
Play mode
Press the play mode button (44) during playback to select repeat and random function, a single track, single folder or all the
tracks can be played in difference mode as follow:(2) repeat all track
(1) repeat 1
Play mode
Repeat 1 track
Repeat all
Repeat folder
Random
Off mode
z
(3) repeat folder
(4) random
(5) off mode
Indicator
on LCD display
FOLDER
RAN
--------------
Repeat play
You can listen the desired tracks or folder repeatedly by this function.
z
Random play
You can listen all the tracks in a random order by this function
USB programming
Up to 30 tacks can be programmed for MP3 play in any order. Before use, be sure to press the “ USB stop
“ button (44)
1. Set in USB mode & stop the playback.
2. Press the “mem/clk-adj” button (44) , “ MEM “ will appear on LCD display (3). Moreover, it will indicate program no. P- 01 .
3. Select a desired track by pressing skip up
or down
buttons (16/44).
4. Press the“ mem/clk-adj ” button (44) to store the track into memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
” button (44) to play the disc in assigned order.
6. When all the desired tracks have been programmed, press “
” button (44) to terminate program play.
7. Press “ stop
EN-6
z
z
z
Press “ stop
“ button (44) at USB stop mode to cancel all programmed memory.
Press the “ folder / pre-up “ button (44) to select the 1st track of next folder directly and hence to speed up the song
selection.
The programming model will automatically stop if no button is being pressed in a period of about 10 seconds after
pressing the “ mem/clk-adj “ button (44).
Listing to tape
General operation
Select the function button (26) to select Tape mode. The LCD display (3) will show “ TAPE ”
Cassette playback
: The system will start the playback automatically after inserting
of cassette tape
Stop and ejection
: Press the “ Tape forward / Eject “ button completely inwards
and the cassette tape will be ejected though the cassette door cover. The “ Tape forward /
Eject “ button will keeping at lowest height position.
Fast forward
: Press the “ Tape forward / Eject “ button half inwards during
Playback mode, the tape winding forward direction. The “ Tape forward / Eject “ button will
keeping at middle height position.
Slightly press the “ Tape forward / Eject “ button again to resume normal playback. The “ Tape
forward / Eject “ button will resume to the highest position.
Remark
-
Make sure the direction is correct when inserting the tape into the system.
-
There is some searching noise can be heard and the system cannot perform normal playback function during fast
forward mode.
-
This is recommended to take out the cassette tape from the system every times after listening and don’t leave the
cassette tape inside the system when not under playback mode.
Phono Operation
-
Remove the stylus protector.
Be sure that the tone arm is being detached from the tone arm rest before operating and
re-secured again afterwards.
1.
Select the Function button (5/45) to “ Source ” position. The LCD display (3) will show
“ PHONO”
Set the speed selector (29) to the proper position depending on the record to be played.
Place the record on the platter (use the spindle adaptor if required).
Set the cueing lever (30) to the up position.
Lift the tone arm from the rest and slowly move it to the record side. The platter will start to rotate and position the tone
arm over the desired position of the record.
Pull down the cueing lever (30). The tone arm will come slowly on the recorder and start playback.
At the end of record, the tone arm will return to the rest position automatically.
To stop manually, lift the tone arm from the record and return it to the rest.
2.
3.
4.
5.
6.
7.
8.
z
Play suspension
Set the cueing lever (30) to the up position will life up the tone arm and then stop playback temporarily.
Remark :
- Due to the auto return system was mechanical design and reset point will affected after transportation.
Thus, the tone arm will return to the rest automatically when first time place the tone arm to the platter
and it was not the malfunction.
- Due to the length of the record is various, if you find the tone arm cannot return automatically after
playback the record. Please press the eject button and return the tone arm back to the rest position
- Users should not change to a magnetic cartridge system, otherwise unit cannot be connected anymore
to an aux-in of music-centre
EN-7
Adjustments
-
-
Anti-skating control
The anti-skating control (28) is made the stylus more stable and this
relative to the different type of vinyl, thus, just set it to the comfortable
position as you desired.
Tone arm stopping position alignment
The position of the tone arm complete playback and return to the rest
station can be adjusted at the alignment screw (26) as follow:Before starting the alignment, please take out the hole covering rubber:-
A) If the system cannot complete the playback of record and return earlier
1) Use a cross head screw driver and turning the alignment screw (26) inside the hole clockwise, the stopping and eject
position of the tone arm will move more inward to the center of the record before playback completion.
B) if the system cannot return to rest position automatically after playback of record
2) use a cross head screw driver and turning the alignment screw (26) inside the hole anti-clockwise, the stopping and eject
position of the tone arm will move more away from the center of the record before playback completion.
Remark:-
The stopping position is very subjective among difference customer, please select the most suitable position based on
your own record collection. The ex-factory setting is based on the most common template.
Please check the stopping position time by time during adjustment and avoid over turning of the screw inside.
Line out connection
You can connect the system to your whole hi-fi system by connecting the line out socket (32) to the auxiliary input socket with
a RCA cable (not included).
Remark : Due to ErP stage two requirement and to protect the environment, the unit will
switch to standby mode automatically once no any music playing over 15 minutes.
Remote control transmitter
Battery installation (battery not provided)
The infra-red transmitter requires 2 pc AAA size battery for operation
Button description
35) Stnadby/On button
36) Play/Pause
37) Skip up
/down
Operate the unit to standby or on mode
In CD mode, press once to start playback.
Press again to enter pause mode
Press to select previous / next tracks in CD
mode
38) Stop
In CD mode, press to stop
39) Display
Press to show different information
40) Rec Level+/-
Press to select CD-R record level
41) Preset EQ
Press to select different EQ mode
42) Volume +/-
Press to adjust the volume level
43) CD-R operation button
playback
Press to operate CD-R function such as Record,
TS…etc
44) USB/Tuner operation button
Press to operate USB/Tuner function such as
program/play mode preset up…etc
45) Function button
Press to change the function mode such as
Tuner, CD, USB…etc
46) Program
In CD mode, press to active programming function
47) Repeat button
Press to active report function of CD-R
EN-8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement