OWNERS GUIDE
TT SS |
c=)
ADYANCED REMOTE STARTER
FOR MANUALTRANSMISSION ONLY
Wu = Г) =
ъ DT ГР
INNOVATIONS
www.titaninnovations:ca
OWNER'S MANUAL REMOTE VEHICLE STARTER
Safety
VERY IMPORTANT SAFETY NOTES!
i he owner/user MUST INSTALL a CARBON MONOXIDE \
9
DETECTOR in the living area near to where the vehicle is bein
stored or parked. It is the sole responsibility of the owner/user
to keep the remote transmitters away from the reach of
children and handle with care so that the system does not
unintentionally start. When the vehicle is parked in an enclosed
Ipartially enclosed area (ex: garage, car port...), being serviced
(ex: oil change) or if the vehicle is loaned to an operator not
familiar with a remote starter, the system MUST BE placed in
Service (Valet) Mode.
MANUAL TRANSMISSION STARTERS the installation of a
remote starter MUST only be done with a specified manual
transmission starter. It is the sole responsibility of the vehicles
owner to insure that the vehicle is left with the transmission in
neutral position when the remote starter is in use. The manual
transmission starter is designed to be an added measure of
safety ONLY! The manufacturer does not guarantee or insure
against any damages or loss of life that could result in the
event of a remote starter starting while the vehicle is in gear.
Manual transmission models are designed only to act as a
deterrent against the vehicle starting in gear, this is the
vehicle's owner's and operator's responsibility.
NEVER OPERATE THE SYSTEM IN AN ENCLOSED/ PARTIALLY
ENCLOSED AREA!
REMOTE VEHICLE STARTER OWNER'S MANUAL
SERVICE (VALET) MODE
System Service Mode will disable the remote starter. This will only effect the
remote start portion of the system. The optional lock, unlock and trunk release
features will still be operational. When the vehicle is to have any under hood or
service work done, the system must be placed into Service Mode. This feature
may also be used if a transmitter is lost, damaged or if the system malfunctions.
ENTERING SERVICE MODE
1. Turn the ignition key to the On position.
2. Press and hold the Program Button (Located on the antenna) for 5 seconds
or until the horn (optional) honks five times.
NOTE: The LEDs on the antenna will turn on solid to confirm Service Mode.
If the O button is pressed while the system is in Service Mode the
park lights will flash 3 times slowly.
EXITING SERVICE MODE
1.Turn the ignition key to the On position.
2. Press and hold the Program Button (Located on the antenna) for 5 seconds
or until the horn (optional) honks two times.
NOTE: The LEDs on the Antenna will turn off and the remote starter functions
will be re-enabled. Q
5 secs
ATTENTION:
TO AVOID SERIOUS INJURY, this remote start system must be set into
Service Mode before any under hood servicing is started. Service Mode
Will prevent the vehicle from starting while the vehicle is being serviced.
It is the sole responsibility of the vehicle’s owner to place the system into
Service Mode. The manufacture accepts no responsibility for accidental
starting of the vehicle while the vehicle is being serviced.
OWNER'S MANUAL
Button Operations
REMOTE VEHICLE STARTER
Car Finder
Status
ACTION
FUNCTION
Press LOCK a button once
Locks doors* and activates Starter Disable**
Press LOCK a once then press and hold
Window Roll-up***
Press UNLOCK В button once
Unlocks doors* and deactivates Starter Disable**
Press and hold LOCK Г for 3 sec
Remote panic*
Press and hold UNLOCK D for 3 sec Trunk release*
Press Lock) & unLockKÉ> buttons simultaneously Silent Lock or Unlock
Press START u button once Remote engine starter on
Press and hold START uu button for 3 seconds Remote engine starter off
Press and hold the E button for 3 sec Car finder*
Press Y button once then A button for 3 sec Timer Start mode on/off
* This feature is not available for all vehicles.
** Optional feature, requires additional parts & installation.
*** Vehicle must be equipped with factory window roll-up feature.
REMOTE VEHICLE STARTER OWNER'S MANUAL
Car Finder
Status
FUNCTION CONFIRMATION CHART
Whenever a command is sent to the vehicle by the transmitter, a confirmation is sent back
using button flashes and beeps. Use the table below to identify the comfirmations for all the
different system functions.
Function Button 1 Button 2 Button 3 Button 4 Button 5 Beep(s)
Lock 3 Flashes X X X X 1
Unlock X 3 Flashes X X X 2
Trunk X X X 3 Flashes X 3
Start X X 1 Flash X X 1
Running On for 4 X X X X 6
seconds
Stop X X X X 5 Flashes 5
Activate Cold| on for 3 on for 3 on for 3 on for 3 1
Start Timer seconds seconds seconds seconds
Start Timer | 3 Flashes* | 3Flashes' | 3Flashes* | 3Flashes* x x
confirmation
OWNER'S MANUAL REMOTE VEHICLE STARTER
Car Finder
Status
CHECKING VEHICLE STATUS
A status check will tell you if your vehicle s doors are locked or unlocked, or if the vehicle is
running and if so, approx. how much runtime is left.
To see vehicle status: Press and release button 5 (Status button)
Observe the transmitter 5 response and use the tables below to determine vehicle status.
* The first flash will indicate the status of the doors (locked or unlocked)
* If the vehicle is running under remote start, a second set of flashes will occurs a few
seconds later. This indicates approx. runtime left.
Status Button 1 Button 2 Beep(s)
Doors Locked On for 3 X 1
seconds
Doors x On for 3 2
Unlocked seconds
If the engine is running under remote start, your doorlock confirmation will be followed by a
‘runtime left’ indication. Use the chart below...
Runtime Button 1 Button 2 Button 3 Button 4 Beep(s)
remaining
75%-100% On On On On 3
50%-75% X On On On 3
25%-50% X X On On 3
0%-25% X X X On 3
REMOTE VEHICLE STARTER OWNER'S MANUAL
REMOTE START SETUP (Ready Mode)
To remote start the vehicle, you must first place the system in ready
mode’. There are 3 different programming options for doing this. To use
a method other than the default, you must have your system
re-programmed by an authorized dealer.
DEFAULT - Transmitter activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Press and release the START button on the remote transmitter.
3. Remove the key from the ignition (vehicle will stay running)
4, Exit the vehicle and make sure all doors are closed.
5. Press and hold START button on the transmitter to shut the vehicle down.
6. The vehicle can now be started by remote. (ready mode)
OPTION - Brake switch activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Press and release the brake pedal 2 times (once if it was already on
when you applied the park brake in step 1).
3. Remove the key from the ignition (vehicle will stay running)
4, Exit the vehicle, upon closing the last door, the vehicle will shut down.***
5. The vehicle can now be started by remote. (ready mode)
OPTION - Park brake activation
1. With the engine on, transmission in NEUTRAL, apply the park brake.
2. Remove the key from the ignition (vehicle will stay running)
3. Exit the vehicle, upon closing the last door, the vehicle will shut down.***
4, The vehicle can now be started by remote. (ready mode)
REMOTE STARTING - All modes
A. With the engine off, press the START button.
B. The parking lights will flash and the horn will chirp once (if connected).
C. The vehicle's ignition system will come on and within 3 seconds, the
vehicle will start. (If vehicle does not start, see the diagnostics section
for possible solutions.)
D. The parking lights will flash 5 times to confirm a successful start.
E. The vehicle will run for the programmed runtime (15 minutes default).
OWNER'S MANUAL REMOTE VEHICLE STARTER
TEA ALIAS)
*** Tf you press the START button on the transmitter while the door is open,
the system will go into continuous run and NOT shut down when you close
the door. It will run for the programmed run time or until it is shut down by
remote. This feature is convenient if you need to open other doors after
having closed yours.***
IMPORTANT: If a door is opened while the vehicle is not running and in
‘ready mode’, the system will go out of ready mode and will not remote
start. You will need to start the vehicle with the key and repeat the proce-
dure. If you need to open doors and want to avoid repeating the 'ready
mode’ setup again, simply remote start the vehicle and open the door
while the vehicle is running. When you are done, and the doors are closed, you
can shut down the vehicle with the remote and ready mode will still be engaged.
A. Press LOCK € button momentarily.
B. Parking lights will flash 1 time, horn will honk 1 time*, doors will lock.
C. The LED on the antenna will begin to flash slowly.
D. If the optional starter-disable circuit has been installed, it will activate as well.
A. Press UNLOCK button momentarily.
B. Parking lights will flash 2 times, horn will honk 2 times*, doors will unlock.
C. The LED on the antenna will stop flashing. (If passive starter-disable is
programmed, the LED will flash quickly for 60 seconds then rearm automatically.)
D. If the optional starter-disable is installed, it will be deactivated to allow the
vehicle to be started by key.
SILENT LOCK/UNLOCK
A. Press both LOCK €) and UNLOCK £ buttons simultaneously.
B. Parking lights will flash once or twice to indicate doors locking or unlocking.
C. Any programmed horn confirmations are temporarily bypassed.
REMOTE VEHICLE STARTER OWNER'S MANUAL
TRUNK RELEASE --OPTIONAL--
The vehicle must be equipped with a power trunk release switch or a power sliding door to
use this option.
A. Press and hold the UNLOCK É' button.
B. The doors will unlock and after 3 seconds, the trunk release will activate.
C. The trunk release can also be programmed to work independently on the CAR
FINDER button. If programmed, press and hold the CAR FINDER & button for 3
seconds to activate trunk release.
2nd VEHICLE OPERATION
Your transmitter is capable of controlling a second TS141/TS151 system installed on
another vehicle. (Requires some special programming, see your dealer for details.)
Switching control from one vehicle to the other is simple:
A. Press and hold the button, the transmitters blue light comes on
solid.
B. Within 3 seconds, press any button to activate the corresponding feature for
your second vehicle.
C. The transmitter automatically defaults back to your primary vehicle after any
command to the 2nd vehicle or if no command is issued within 5 seconds.
PANIC MODE
To use Panic mode, the vehicle s horn must be connected to your remote starter.
A. Press the LOCK button for 3 seconds.
B. The horn will sound and the parking lights will flash for 60 seconds.
C. Pressing the LOCK or UNLOCK buttons will cancel Panic mode.
CAR FINDER
To use Car Finder mode, the vehicle's horn must be connected to your remote starter.
A. Press and hold the CAR FINDER button for 3 seconds.
B. The parking lights will flash and the horn will chirp 5 times.
NOTE: Car Finder option is not available when the trunk release option has been
programmed to work on this button
OWNER'S MANUAL REMOTE VEHICLE STARTER
TURBO MODE
This option allows for a cool down on turbo equipped vehicles.
A. With the engine running, press the CAR FINDER E button. (Brake pedal must
not be depressed)
B. The parking lights will flash and the horn will chirp 2 times*.
C. Remove the ignition key and the engine will continue to run for approximately 2
minutes.
ЦОЙ)
This option allows you start your vehicle automatically at preset intervals over a 24-hour
time period. Please note: Vehicle must be in “Ready Mode” to activate the Timer Start,
A. Press and release the CAR FINDER button, then press and hold the START button
for about 3 seconds until buttons 1 through 4 illuminate solid; the parking lights on
the vehicle turn on as well.
B. Within 5 seconds, select your start interval by pressing one of the 4 buttons on
the transmitter (See table below)
C. Once you have selected your start interval, the appropriate button will flash 3
times to confirm the programming. The parking lights will flash as well.
D. The vehicle will start every (your selection) hours for a period of 24 hours.
E. To cancel timer start mode, repeat step 1. The parking lights will flash and the
horn will chirp 2 times. *
NOTE: Starting the vehicle by key or by remote will automatically cancel timer
start mode.
LOCK (button 1) 1 Flash 3 flashes on button 1 Vehicle with start every hour
UNLOCK (button 2) 2 Flashes 3 flashes on button 2 | Vehicle will start every 2 hours
START (button 3) 3 Flashes 3 flashes on button 3 | Vehicle will start every 3 hours
CAR FINDER (button 4) 4 Flashes 3 flashes on button 4 | Vehicle wil start every 4 hours
REMOTE VEHICLE STARTER OWNER'S MANUAL
TRANSMITTER LEARNING
Important! The remote starter will hold 4 transmitter codes.
It is recommended that when programming in transmitters,
you fill up all four transmitter codes, even if only using one or
two transmitters. This will clear all other transmitter coding
from the unit and prevent stray coding or possible
interference from other remote transmitters.
STEP 1 - Within 3 seconds turn the ignition key to the “ON”
position three times leaving “ON” the third time. to
STEP 2 - Press and hold the Program Button. The park
lights will turn “ON” and the horn (optional) will
honk once. Continue to hold the Program
Button, the park lights will turn “OFF” and the
horn (optional) will honk 5 times quickly.
A
NOTE: If the parking lights do not turn “ON”, release the Program Button and
turn the ignition to the “OFF” position, wait 5 sec and repeat steps 1 & 2.
STEP 3 - While holding the Program Button, press and
release the O button on each of the remote
© transmitters to be programmed. If using two
transmitters, code in each transmitter twice.
OWNER'S MANUAL REMOTE VEHICLE STARTER
If the remote starter does not activate when the © button is
pressed, the park lights will flash a diagnostic code to indicate what
shutdown input has been triggered.
Transmitter Vehicle lights | Problem Solution
X 3 slow flashes [system is in valet mode Cancel Valet Mode
5 flashes on button 2 | 4 slow flashes [Deo Open Manual trans. models only
5 flashes on button 3 | 5 slow flashes gon ON Turn off Ignition key and try again
5 flashes on button 1 | 5flashes TBrakeswitch engaged Contact your product dealer
5 flashes on button 4 | — 6flashes Hoods (hood open) Contact your product dealer
X 7 flashes ach lock-out Start vehicle with key, after 5 sec. try again
BATTERY REPLACEMENT
When your starter system begins to show a significant reduction in transmitter range, or the
remote does not respond correctly, it may be time to change the batteries. The transmitter
uses 2 CR2032 3V Lithium batteries.
A. Open the transmitter at the notch in the casing near the pin for the keychain.
Use a small tool or a coin to gently pry the top and bottom apart.
B. Once the 2 pieces are seperated, slide out the 2 batteries under the battery clip.
C. Replace with 2 new CR2032 Lithium batteries.
D. Press top and bottom of casing together until they snap back in place.
If the transmitter shows no significant improvement after replacing the batteries, contact
your product dealer to have the system inspected.
REMOTE VEHICLE STARTER OWNER'S MANUAL
Limited Lifetime Warranty
The manufacturer warrants to the original purchaser of the remote starter and/or alarm, that the
product shall be free from defects in material and workmanship. However, should this product be
proven to be defective, within a three year period from the original date of purchase, the
manufacturer will, without charge to the purchaser (excluding any charges incurred to have the
product delivered to the manufacturer), repair or replace any part of the remote starter and/or alarm
which the manufacturer agrees to be defective. After the initial three year period the manufacturer
shall repair or replace defective products with a nominal processing fee of $35.00 USD. All
warranties apply to the original purchaser and the vehicle in which the unit was originally installed
ONLY. Repairs or replacement of defective modules shall remain at the discretion of the
manufacturer. All other parts, components, accessories, and/or optional equipment pertaining to
the remote starter and/or alarm are not included in the manufacturer's warranty. This warranty is
non-transferable. Request for warranty service from any Factory Authorized Dealer must be
accompanied with the original purchase receipt. Failure to comply with any ofthese conditions may
result in warranty being voided. This warranty does not cover the following: removal and reinstall
labor charges, shipping charges, abuse, misuse, or accidental damages to the remote starter
and/or alarm, automobile, and/or parts thereof. This warranty is void upon modification, repairs, or
alterations to any part of the product. The manufacturer does not guarantee or insure against theft
of the vehicle orits contents. Alarm models are designed only to actas a deterrent against possible
theft. This alarm may qualify for auto insurance discounts. Contact your insurance agent for further
information. The manufacturer shall not be held liable for any consequential damages due to
breach of this or any other warranty, expressed or implied. This warranty gives you specific legal
rights. Your specific legal rights may vary for each region.
CERTAIN DAMAGES EXCLUDED — The manufacturer expressly disclaims any liability or
responsibility for incidental damages caused by the product, including economic loss, loss of use of
the product, car rentals, or any other costs relating to the care and custody of the product. The
manufacturer disclaims liability or responsibility for any consequential damages caused by the
product or resulting from its use, including the cost of repairing or replacing other property damaged
by the product or caused by its use, whether or not the product is working properly. The product is
intended to deter unauthorized use of the vehicles in which it is installed. The manufacturer does
not warrant that the product is fool-safe against theft and/or vandalism and/or human error or
misuse. The manufacturer accepts no liability or responsibility for any damage of any kind
whatsoever caused to any vehicle in which the product is installed or any resulting damage from its
use. The manufacturer accepts no responsibility or liability for any damage resulting to or theft of
the vehicle or its contents caused or alleged to be caused, directly or indirectly, by failure of the
product.
MANUAL TRANSMISSION STARTERS - The installation of a remote starter in a manual
transmission vehicle MUST only be done with a specified manual transmission starter. The
manual transmission starter is designed to be an added measure of safety ONLY! The
manufacturer does not guarantee or insure against any damages or loss of life that could
result in the event of a remote starter starting while the vehicle is in gear. Manual
transmission models are designed only to act as a deterrent against the vehicle starting in
gear. Itis the sole responsibility of the vehicle's operator to insure that the vehicle is left with
the transmission in neutral position when the remote starteris in use.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may
cause undesired operation.
3) CAUTION: Changes or modifications not expressly approved by the part responsible
for compliance voids the user's authority to operate this device.
OWNER'S MANUAL REMOTE VEHICLE STARTER
Notes:
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation
CAUTION: Changes or modifi ications not expressly approved by the part responsible for
compliance void the user's authority to operate this devise.
">
